Chief K1P220B User Manual
Displayed below is the user manual for K1P220B by Chief which is a product in the Monitor Mount Accessories category. This manual has pages.
Related Manuals
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
K1P110
K1P22H
K1P220
K1P120 K1P120XRH
K1P220XRH
K1P Pole Mounts
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
K1P Series
K1P Series Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components and accessories attached to the K1P Series
Monitor Arm up to (and including) the display does not
exceed the weight limits listed below. Use with products
heavier than the maximum weight indicated may result in
collapse of the mount and its accessories causing possible
injury.
--SAVE THESE INSTRUCTIONS!--
MODEL Max Weight
Allowed for EACH
Display
Max Weight
Capacity of
Mounting System
K1P110 25 lbs
(11.34 kg)
25 lbs
(11.34 kg)
K1P120 25 lbs
(11.34 kg)
25 lbs
(11.34 kg)
K1P120XRH 25 lbs
(11.34 kg)
25 lbs
(11.34 kg)
K1P22H 9 lbs
(4.08 kg)
18 lbs
(8.16 kg)
K1P220 25 lbs
(11.34 kg)
50 lbs
(22.68 kg)
K1P220XRH 25 lbs
(11.34 kg)
50 lbs
(22.68 kg)
Installation Instructions K1P Series
3
DIMENSIONS
K1P110
DYNAMIC HEIGHT
ADJUST RANGE
14.59
1.59
370.5
40.3
TILT RANGE
75 UP
10
DOWN
0.78
19.8
DYNAMIC LIFT ARM
LENGTH RANGE
STRAIGHT ARM = MAX
FULL UP/DOWN = MIN
10.21
7.12
259.3
180.9
1.97
50.1
POLE CLAMP RANGE
1.50" - 1.90"
[38.1 - 50.8]
INTERFACE ROTATION RANGE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
INTERFACE
ROTATION
RANGE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
0.81
20.6
6.75
171.5
DYNAMIC LIFT ARM
LENGTH RANGE
STRAIGHT ARM = MAX
FULL UP/DOWN = MIN
10.21
7.12
259.3
180.9
1.50" - 1.90"
[38.1 - 50.8]
HEIGHT RANGE
25.88
12.88
657.3
327.1
TILT RANGE
75
UP
10
DOWN
K1P22H
K1P Series Installation Instructions
4
K1P120
DYNAMIC HEIGHT
ADJUST RANGE
24.26
11.26
616.3
286.1
TILT RANGE
75
UP
10
DOWN
6.75
171.5
0.78
19.8
DYNAMIC LIFT ARM
LENGTH RANGE
STRAIGHT ARM = MAX
FULL UP/DOWN = MIN
10.21
7.12
259.3
180.9
1.97
50.1
POLE CLAMP RANGE
1.50" - 1.90"
[38.1 - 50.8]
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
INTERFACE
ROTATION
RANGE
90
K1P120XRH
DYNAMIC HEIGHT
ADJUST RANGE
17.81
4.81
452.4
122.2
TILT RANGE
75 UP
5 DOWN
6.75
171.5
0.78
19.8
DYNAMIC LIFT ARM
LENGTH RANGE
STRAIGHT ARM = MAX
FULL UP/DOWN = MIN
10.21
7.12
259.3
180.9
1.97
50.1
POLE CLAMP RANGE
1.50" - 1.90"
[38.1 - 50.8]
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
INTERFACE
ROTATION
RANGE
90
Installation Instructions K1P Series
5
INTERFACE
ROTATION
RANGE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
0.81
20.6
6.75
171.5
DYNAMIC LIFT ARM
LENGTH RANGE
STRAIGHT ARM = MAX
FULL UP/DOWN = MIN
10.21
7.12
259.3
180.9
1.50" - 1.90"
[38.1 - 50.8]
HEIGHT RANGE
25.88
12.88
657.3
327.1
TILT RANGE
75
UP
10
DOWN
K1P220
K1P220XRH
INTERFACE
ROTATION
RANGE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
0.81
20.6
6.75
171.5
DYNAMIC LIFT ARM
LENGTH RANGE
STRAIGHT ARM = MAX
FULL UP/DOWN = MIN
10.21
7.12
259.3
180.9
1.97
50.1
1.28
32.5
POLE CLAMP RANGE
1.50" - 1.90"
[38.1 - 50.8]
HEIGHT RANGE
19.43
6.43
493.5
163.3
TILT RANGE
75 UP
5 DOWN
K1P Series Installation Instructions
6
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions K1P Series
7
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/16” (included)
1/8” (included)
5/32” (included)
A (1)
[Pole clamp arm]
(K1P110 shown)
B (4/8)*
M4x10mm C (4/8)*
M4x20mm
D (4/8)*
M10x5.3x10
J (1) - included with K1P22H only!
3/16”
1/8”
L (1)
M (1)
E (1)
[pole clamp] F (4)
1/4-20 x 1 1/2”
G (4)
1/4-20 x 1" 5/32”
K (1)
* - (single display models/dual display models)
H (1/2)*
#10-32 x 3/8”
J1 (1)
[Array] J2 (1)
[Handle]
J5 (1)
5/16-18 x 3"
J4 (1)
[Pivot pin]
J6 (1)
[Pocket washer]
J3 (1)
5/16-18
J7 (2)
[Array Cable
J8 (2)
[Thin steel J9 (1)
[Plastic J10 (1)
[Rotational
spacer]washer] washer] clip]
J11 (1)
[Cable clip]
J12 (1)
[Pivot point
spacer]
N (1/2)*
M4x4mm
K1P Series Installation Instructions
8
Assembly And Installation
Connecting to Pole
1. Determine approximate location for mount keeping in mind
display size, extension, height adjustment requirements.
2. Place mount (A) against pole with clamp (E) on opposite
side of pole. (See Figure 1)
Figure 1
3. Using 5/32” hex key (L) and appropriate length screws,
loosely attach assembly to pole clamp (E). If installing to
1 1/2” NPT pipe, use 1/4-20 x 1 1/2” button head cap screws
(F). If installing to 1 1/2” diameter pipe, use 1/4-20 x 1"
button head cap screws (G). (See Figure 1)
4. Position mount at desired height and orientation.
5. Equally tighten screws against mount and the pole clamp.
Array Installation (K1P22H ONLY)
1. Slide rotational spacer (J10) into opening on array
attachment bracket. (See Figure 2)
2. Use 5/16-18 x 3" button head cap screw (J3), two thin steel
washers (J8), plastic spacer (J9), pocket washer (J5), pivot
pin (J4), pivot point spacer (J12) and 5/16-18 lock nut (J6)
to secure array (J1) to K1 arm (A). (See Figure 2)
NOTE: Cable clip (J11) can be used in place of pivot point
spacer (J12) if additional cable management is desired.
(See Figure 2)
Figure 2
Display Installation
1. Remove quick release faceplate from mount by pulling
quick release lever and sliding faceplate off mount. (See
Figure 3)
Figure 3
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! See
Display Removal section for details.
3
(F or G) x 4
(E)
(A)
(J10)
1
(J3)
2
(J9)
(J8) x 2
(J5)
(J1)
(J4)
(J6) (A)
(J12)
or
(J11)
quick release lever
1
1
Installation Instructions K1P Series
9
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the K1P Series Monitor Arm up to
(and including) the display does not exceed the weight limits
listed below. Use with products heavier than the maximum
weight indicated may result in collapse of the mount and its
accessories causing possible injury.
2. Carefully place display face down on protective surface.
3. Connect faceplate to display
For flush mounting hole installation:
• Using Phillips screwdriver, carefully install four
M4x10mm screws (B) through corresponding
holes on faceplate and into the mounting holes on
the display. (See Figure 4)
Figure 4
For recessed mounting hole installation:
• Place four spacers (D) on top of mounting holes
on back of display. (See Figure 5)
• Using Phillips screwdriver, carefully install four
M4x20mm screws (C) through corresponding
holes on faceplate, spacers (D) and into the
mounting holes on the display. (See Figure 5)
Figure 5
4. Position display with faceplate attached above mount. (See
Figure 6)
5. Slide faceplate onto mounting head until quick release tab
clicks into place. (See Figure 6)
Figure 6
MODEL Max Weight
Allowed for EACH
Display
Max Weight
Capacity of
Mounting System
K1P110 25 lbs
(11.34 kg)
25 lbs
(11.34 kg)
K1P120 25 lbs
(11.34 kg)
25 lbs
(11.34 kg)
K1P120XRH 25 lbs
(11.34 kg)
25 lbs
(11.34 kg)
K1P22H 9 lbs
(4.08 kg)
18 lbs
(8.16 kg)
K1P220 25 lbs
(11.34 kg)
50 lbs
(22.68 kg)
K1P220XRH 25 lbs
(11.34 kg)
50 lbs
(22.68 kg)
(for flush mounting holes)
(B) x 4
quick release
faceplate
3
(for recessed mounting holes)
(C) x 4
(D) x 4
quick release
faceplate
3
5
K1P Series Installation Instructions
10
Handle Installation (K1P22 model only)
1. Loosen four screws securing handle brackets to K1P22
array. (See Figure 7)
2. Install uprights of handle (J2) into handle brackets located
on the back of array. (See Figure 7)
Figure 7
3. Position handle (J2) at desired height and secure by
tightening button head cap screws attaching handle
brackets to array. (See Figure 8)
Figure 8
Adjustments
Pitch Adjustment (non-array models)
1. Adjust pitch to desired tilt position. (See Figure 9)
2. Adjust pitch tension screw to change the adjustment
tension. (See Figure 9)
Pivot Adjustment (non-array models)
3. Adjust pivot position as desired. (See Figure 9)
4. Use 3/16” hex key (L) to adjust pivot point tension screws to
change pivot adjustment tension. (See Figure 9)
Figure 9
Rotational Adjustment
NOTE: (Optional) Rotational adjustment may be locked by
installing rotational locking screw (M) into back of
faceplate. (See Figure 10)
Figure 10
5. The monitor may be adjusted 90 degrees in either direction
in order to provide a portrait view of the monitor. (See Figure
9)
6. Use 3/16” hex key (L) to adjust rotational adjustment screw
to adjust rotational tension. (See Figure 9)
2
2
(J2)
1
x 4
3
3
3
x 4
pitch
pivot point
tension
tension
5
1
3
Rotational tension
6
(M)
Installation Instructions K1P Series
11
Lift Arm Tension Adjustment
1. Tension may be adjusted with tension adjustment screw
inside cable management cover and 1/8” hex key (M). (See
Figure 11)
Figure 11
Adjustments - K1P22H models only
1. Loosen knobs securing faceplates to array. (See Figure 12)
2. Slide displays laterally on array to adjust lateral shift. (See
Figure 12)
3. Adjust pitch and pivot position as desired. (See Figure 12)
4. Tighten knobs to secure faceplates in position. (See Figure
12)
Figure 12
Array Bar Roll Adjustment
1. Loosen roll adjustment screws on back of array bracket.
(See Figure 13)
2. Adjust roll of array bar as desired. (See Figure 13)
3. Tighten roll adjustment screws on back of array bracket.
(See Figure 13)
Figure 13
Display Removal
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! (See
Figure 14)
1. Make sure display is in the upright position.
2. Remove quick release faceplate from mount by pulling
quick release lever and sliding faceplate off mount. (See
Figure 14)
Figure 14
Reduce tension
Increase tension
(lighter display)
(heavier display)
Do NOT over-tension
adjustment tension
screw.
2
3
2
1 4
3
3
3
13
2
2
quick release tab
2
K1P Series Installation Instructions
12
Display Removal Security Screw
NOTE: In order to prevent display from being easily removed
from mount using the quick release lever, install
M4x4mm security screw (H) into lower hole on back of
faceplate. (See Figure 15)
Figure 15
Pivot Adjustment Range
Single Arm Models
1. Adjust arm angle as desired up to 90 degrees in either
direction. (See Figure 16)
WARNING: Swinging the arm beyond 90 degrees may
result in the mount slipping off the desk causing serious
injury!
Figure 16
Dual Arm Models
1. Adjust arm angles as desired within a 90 degree range from
the pivot point of the arm and a perpendicular centerline of
mount. (See Figure 17)
WARNING: Swinging the arm beyond this range may result
in the mount slipping of the desk causing serious injury!
Figure 17
Cable Management
1. Press insides of cable management covers at both ends to
unhinge tabs on either end of cable management cover on
upper arm. (See Figure 18)
2. Lift cable management cover up until tabs are unhinged and
cover is in the “open” position. (See Figure 18)
Figure 18
(H)
(top view)
+/- 90 degrees range
of motion
pivot point of the arm
perpendicular centerline
90 degrees range
of motion per arm
pivot point of the arm
(top view)
cable management cover tabs
1
2
Installation Instructions K1P Series
13
Figure 19
3. Route cables through cable management channels. (See
Figure 19)
IMPORTANT ! : Be sure to leave enough slack in the
cables near display and arm joint to allow for full arm
articulation!
4. Close cable management covers on monitor arm. (See
Figure 19)
5. Repeat Steps 1-4 for lower arm.
Array Models
1. Install array cable clips (J7) to back of array. (See Figure 20)
2. Route cables through array cable clips (J7) as desired. (See
Figure 20)
3. Route cables through arm cable clips as desired. (See
Figure 20)
Figure 20
2
2
4
4
3
3
cable (typical)
(J7)
2
1
3
K1P Series Installation Instructions
14
Installation Instructions K1P Series
15
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
K1P Series Installation Instructions
8800-002759 Rev02
2019 Legrand | AV
www.legrandav.com
03/19