Chief LFE1U User Manual
Displayed below is the user manual for LFE1U by Chief which is a product in the Signage Display Mounts category. This manual has pages.
Related Manuals
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Electrical Height Adjustable Video Stand
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LFE1U
LFE1U Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
Chief® is a registered trademark of Legrand AV Inc.
DEFINITIONS
WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
DANGER alerts you to an imminently
hazardous situation which, if not avoided, will result in death or
serious injury.
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: FAILURE TO READ AND FOLLOW
THE FOLLOWING INSTRUCTIONS CAN RESULT IN
SERIOUS PERSONAL INJURY, DAMAGE TO EQUIPMENT
OR VOIDING OF FACTORY WARRANTY. It is the installer’s
responsibility to make sure all components are properly
assembled and installed using the instructions provided.
When using an electrical mounting system, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS
PRODUCT!!!!
DANGER: TO REDUCE THE RISK OF
ELECTRIC SHOCK:
1. Always turn off power at source before cleaning.
WARNING: TO REDUCE THE RISK OF
BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS:
1. Unplug from outlet before putting on or taking off parts.
2. Close supervision is necessary when this furnishing is used
by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in
these instructions. Do not use attachments not
recommended by the manufacturer.
4. Never operate this mounting system if it has a damaged
cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the
mounting system to a service center for examination and
repair.
5. Keep the cord away from heated surfaces.
6. Never operate the furnishing with the air openings blocked.
Keep the air openings free of lint, hair, and the like.
7. Never drop or insert any object into any opening.
8. Do not use outdoors.
9. Do not operate where aerosol (spray) products are being
used or where oxygen is being administered.
10. To disconnect, turn all controls to the off position, then
remove plug from outlet.
11. For loading always put heavier items at the bottom and not
near the top in order to help prevent the possibility of the
furnishing tipping over.
WARNING: Exceeding the weight capacity
can result in serious personal injury or damage to equipment! It
is the installer’s responsibility to make sure the weight of all
components attached to the LFE1U does not exceed 200 lbs
(90.7 kg).
WARNING: Use this mounting system only
for its intended use as described in these instructions. Do not
use attachments not recommended by the manufacturer.
WARNING: Never operate this mounting
system if it is damaged. Return the mounting system to a
service center for examination and repair.
WARNING: RISK OF SERIOUS INJURY OR
DEATH! Risk of death or serious injury may occur when
children climb on audio and/or video equipment furniture. A
remote control or toys placed on the furnishing may encourage
a child to climb on the furnishing and as a result the furnishing
may tip over on to the child.
Installation Instructions LFE1U
3
WARNING: RISK OF SERIOUS INJURY OR
DEATH! Relocating audio and/or video equipment to furniture
not specifically designed to support audio and/or video
equipment may result in death or serious injury due to the
furnishing collapsing or overturning onto a child.
NOTE: The LFE1U stand has no user serviceable parts.
NOTE: The LFE1U stand can support screen sizes up to a
maximum of 86".
NOTE: The LFE1U stand is intended for Institutional Use.
NOTE: To reduce the risk of electric shock, this furnishing has
a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.
NOTE: This product is a double-insulated, cord-connected
product and must be serviced accordingly. In a double-
insulated product, two systems of insulation are
provided instead of grounding. No grounding means for
grounding to be added to the product Servicing a
double-insulated product requires extreme care and
knowledge of the system, and is to be done only by
qualified service personnel. Replacement parts for a
double-insulated product must be identical to the parts
they replace. A double-insulated product is marked
with the symbol (square within a square)
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
IMPORTANT ! : The LFE1U is designed to be mounted
to:
• a bare concrete wall with a minimum thickness of
8" (203mm):
• a bare 8" x 8" x 16" (203mm x 203mm x 406mm)
concrete block wall; or
• a wood stud wall with a maximum drywall
covering of 5/8”.
• a 2" x 4"-25ga minimum steel stud wall.
IMPORTANT ! : Mounting with hardware to the finished
floor is optional, however the LFE1U CANNOT be
mounted exclusively to the floor without also being
attached to the wall!
IMPORTANT ! : The LFE1U must be sitting on the floor
after it is mounted to the wall. It CANNOT be elevated off
the floor!
CAUTION: Changes or modifications to this
unit not expressly approved by the manufacturer can void the
units FCC compliance rating and make the unit illegal to
operate.
Responsible Party:
Legrand | AV
6436 City West Parkway
Eden Prairie, MN 55344
866-977-3901
av.support@legrand.com
CAN ICES-3 (B)/NMB-3(B)
--SAVE THESE INSTRUCTIONS--
Electrical Specifications
Input voltage, frequency 100-240 V~, 50-60 Hz, 450W
Duty Cycle Intermittent: 10%; max 2
minutes on/18 minutes off
LFE1U Installation Instructions
4
DIMENSIONS
18.75
476.3
4.01
101.8
16.25
412.8
TILT
B
C
DD
2.5
ROLL
DETAIL B
SCALE 1 : 5
2X 1.00
25.4
2X 0.75
19.1
2X
0.332
8.4
1.50
38.1
4.00
101.6
DETAIL C
SCALE 1 : 4
3X
0.38
9.5
OPTIONAL ANCHOR
HOLE FOR 1/4" SCREW
0.27
6.8
SECTION D-D
SCALE 1 : 4
FRONT
WEIGHT RATING: 200LB (90KG)
ELECTRICAL RATING:
100-240 VAC, 50-60HZ, 450W
INT. 10%, MAX. 2MIN/18MIN
Installation Instructions LFE1U
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
LFE1U Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/16” (included)
1/8” (included)
7/32" (5.3mm) - wood studs
3/8" (10mm) - concrete
1/2" (12.7mm) - steel/wood studs
1/2"
P (1)
[Column assembly]
C (1)
[Floor plate]
A1 (1) A2 (1)
M(4)
5/16-18 x 3 3/4”
W (1) - Display interface + hardware
H (1)
3/16”
K (10)
[Cable tie]
N (4)
3/16”
S (1)
G (1)
5/16-18 x 1/2"
(See interface parts list on page 7)
T (4)
5/16-18 x 1"
V (1)
[Power cable]
[Control pad bracket]
F (2)
#8-32 x 3/8"
U (1)
[Double-sided tape]
[Lower cover]
5/16-18 x 1/2"
Box "A"
Box "B"
B1 (2)
[Bottom back cover]
Hardware bag 1
J (4)
5/16-18
Hardware bag 2
L (4)
5/16-18 x 2 1/4"
X (4)
[Wall bracket] D (1)
[Control pad + cable]
E (1)
[Motor cable]
Q (4)
5/16 x 2 3/4" R (4)
[Fischer anchor]
Hardware bag 3 Hardware bag 4
LFE1U Installation Instructions
7
PARTS - DISPLAY INTERFACE
WR (2)
WJ (4)
WI (4)
WC (4)
WG (4)
WF (4)
WE (4)
WD (4)
WA (4)
WQ (2)
WK (4)
WH (4)
WL (4)
WP (1)
1/8”
Hardware Kit
Bag A Bag B Bag C
Bag D Bag E Bag F
Bag G Bag H Bag I
Bag J Bag K Bag L
Bag M
WB (4)
M4 x 20mm
#10-24 x 1/2"
M4 x 25mm
M5 x 12mm M5 x 20mm M5 x 25mm
M6 x 12mm M6 x 20mm M6 x 25mm
M8 x 12mm M8 x 20mm M8 x 30mm
[Vertical bracket]
[Horizontal bracket]
M4 x 12mm
WMA (8)
[Nesting spacer]
WMB (4)
[Universal spacer]
WN (8)
LFE1U Installation Instructions
8
Assembly And Installation
IMPORTANT ! : The LFE1U packaging was designed to
help make the installation and setup easier. Do NOT
remove assembly prior to reading installation
instructions!
Cart Assembly
1. Remove all boxes and smaller parts. Leave foam packaging
and other cardboard pieces inside to provide stability while
performing Steps 2-4. (See Figure 1)
2. Lift column assembly (P) up by lifting at the bottom of the
assembly. (See Figure 1)
3. Carefully set column assembly (P) base on the edge of box.
(See Figure 1)
Figure 1
4. Use four 5/16-18 x 1" flat head cap screws (T) button head
cap screws (K) and four 5/16-18" hex nuts (J) to secure floor
plate (C) to column assembly (P) and bottom back cover
(A1). (See Figure 2)
Figure 2
5. Remove stand from box by tipping it from the top onto the
floor plate. (See Figure 3)
Figure 3
6. Attach control pad bracket (S) to column assembly (P) using
5/16-18 x 1/2" button head cap screw (G). (See Figure 4)
Figure 4
7. Secure control pad (D) into control pad bracket (S). (See
Figure 5)
NOTE: Control pad may also be attached to bottom of display
using double-sided tape (U) after display has been
installed.
8. Route control pad cable (D) through side channel. (See
Figure 5) and (See Figure 6)
Figure 5
1
1
remove parts and packaging
2
2
3
3
(P)
4
(P)
(J) x 4
4
A1
(C)
(T) x 4
front corners
slightly curved
5
(G)
7
(R)
6
8
(D)
Installation Instructions LFE1U
9
9. Remove back cover to expose control box. (See Figure 6)
10. Route control pad cable (D) behind bottom back cover (A1)
and into port A1 on control box. (See Figure 6) and (See
Figure 7)
11. Route motor cable (E) behind bottom back cover (A1) and
into port 1 on control box. (See Figure 6) and (See
Figure 7)
NOTE: Bottom back cover (A1) may need to be pulled back or
loosened in order to fit cables behind it.
NOTE: Use cable ties (K) and pre-installed cable clips to
provide tension relief.
NOTE: Knockout holes can be created on A1 bracket for
another cable routing option. (See Figure 7)
Figure 6
IMPORTANT ! : Lower cover (A2) should only be
installed after all cables have been routed with no load.
12. Slide lower cover (A2) onto column assembly (P) and use
two 8-32 x 3/8" Phillips pan machine screws (F) to secure
bottom back cover (A1) to lower cover (A2). (See Figure 7)
Figure 7
13. Plug in power cable (V) to control box and route along side
of control box. Provide strain relief using the cable ties (K)
and cable clips. All three cable clips MUST be used to
prevent cable from rubbing against lower edge of cover!
(See Figure 8)
Figure 8
14. Plug in power cable (V) to outlet.
15. Press and hold "DOWN" button for three seconds to
initialize lift mechanism. (See Figure 9)
16. Press and hold "UP" button until mount reaches it’s
maximum height. (See Figure 9)
NOTE: If lifting mechanism does not function properly refer to
"Troubleshooting" Section.
Figure 9
(D)
10
9
(C)
(E)
into port "A1"
into port "1"
11
(K) x 4 for tension relief
(as needed)
(A2)
12
12
(A1)
(F) x 2
12
knockout
holes
control box
13
required clip
locations
"UP" "DOWN" "PRESETS" "SAVE"
LFE1U Installation Instructions
10
17. Attach display and signal cables to power source. Use cable
ties (K) to route as necessary. (See Figure 10)
IMPORTANT ! : Do not install display at this time, only
route the cables through the back cover.
IMPORTANT ! : Make sure to install cables when lift is at
the highest position and so that there is enough length to
reach input locations for display and signal.
18. Reinstall back cover to column assembly (T). (See Figure
10)
Figure 10
19. (Optional) Relocate control pad to the front center of display
if desired following these steps. (See Figure 11) and (See
Figure 12)
IMPORTANT ! : Make sure to perform these steps when
lift is at the highest position and so that there is enough
length for cable to reach control box.
• A. Unplug control pad cable from the RJ45 port in
the control box.
• B. Remove cable through side cable cover.
• C. Pull cable out through opening at bottom of
cable cover.
• D. Feed removed cable down through back
channel.
• E. Plug cable back into control box into A1 port.
• F. Use double-sided foam tape (U) to attach
control pad to bottom of display in the center.
Figure 11
Figure 12
recommended strain relief
locations
display cable
(example)
(pre-installed cable clips)
17 18
A
B
C
D
F
(rear view)
E
Installation Instructions LFE1U
11
Installation to Wall
IMPORTANT ! : The LFE1U is designed to be mounted
to:
• a bare concrete wall with a minimum thickness of
8" (203mm):
• a bare 8" x 8" x 16" (203mm x 203mm x 406mm)
concrete block wall; or
• a wood stud with a maximum drywall covering of
5/8”.
• a 2" x 4"-25ga minimum steel stud wall.
Installing to Wood Stud Wall
1. Use a stud-finder to locate stud.
2. Measure 5 5/8" off the finished floor to mark lower mounting
locations and 32 5/8" off the finished floor for upper
mounting locations with one of the locations being centered
on stud. Holes must be 4" apart horizontally. (See Figure
13)
3. Mark hole locations at each mounting location. (See Figure
13)
4. Drill two 7/32” holes at marked hole locations on studs. (See
Figure 13)
5. Drill two 1/2" holes on marked hole locations NOT on stud.
(See Figure 13)
Figure 13
6. Follow Steps 7-10 to install toggler anchors into two drywall
holes (not on stud).
7. Hold metal channel on anchor (L) flat alongside plastic
straps and slide channel through hole. (See Figure 14)
Figure 14
8. Holding plastic straps on anchor (L), pull anchor away from
wall until channel rests flush behind wall making sure
anchor channel is positioned vertically on stud. (See Figure
15)
9. Slide plastic cap on anchor (L) towards wall until flange of
cap is flush with wall. (See Figure 15)
Figure 15
10. Snap off plastic straps on anchor at wall by pushing side to
side, snapping off straps level with flange of plastic cap.
(See Figure 16)
Figure 16
11. Repeat Steps 7 through 10 for the other mounting hole not
on stud.
X
X
X
X
5 5/8” above
finished floor
32 5/8” above
finished floor
4
” apart
4” apart
7/32"
on stud 1/2"
(not on stud)
4
5
(L)
Drywall
Plastic Straps
7
(L)
Plastic Cap
Drywall
Anchor Metal Channel
SIDE VIEW
8
9
Plastic Straps
Drywall
Anchor Metal Channel
Plastic Cap
SIDE VIEW
10
LFE1U Installation Instructions
12
12. Place wall brackets (B1) over anchors and drilled holes and
align mounting slots on mount with holes in anchors and
wall. (See Figure 17)
13. Install two 5/16 x 2 3/4" hex head tapping bolts (Q) through
corresponding mounting slots on mount and into drilled
holes on wood stud. DO NOT overtighten! (See Figure 17)
14. Install two 5/16-18 x 3 3/4" Phillips pan machine screws (M)
through 3/16 washers (N) and slots on wall bracket (B1) and
into toggler anchors (L). (See Figure 17)
15. Position column assembly (P) inside two installed wall
brackets (B1). (See Figure 17)
Figure 17
16. Install four 5/16 x 1/2” button head cap screws (X) through
holes on wall brackets (B1) and side of column assembly
(P). (See Figure 18)
Figure 18
Installing to Steel Stud Wall
13
14
(Q) x 2
(M) x 2
(N) x 2
15
(X) x 4
16
(P)
Installation Instructions LFE1U
13
Site Requirements (Steel Studs)
Drywall
**1/2" minimum
Drywall Thickness
LFE1U Installation Location
FRONT
(Both Sides of Stud)
There must be a minimum of
1-7/8" (48mm) clearance
inside wall
16" (on center) Studs
If back side of wall is unfinished, drywall must be installed
to a minimum of one stud left and right of the studs
being used to install the mount. Drywall must be
secured to studs with screws 12" on center
Steel Stud (2 x 4 / 25ga minimum)
Stud type and structural strength must conform to the North American
Specification for the Design of Cold-Formed Steel Structural Members.
**See hazard statement
on page 2!
[362, 125 18, C-Shape, S - Stud Section]
LFE1U Installation Instructions
14
1. Measure 5 5/8" off the finished floor to mark lower mounting
locations and 32 5/8" off the finished floor for upper
mounting locations with one of the locations being centered
on stud. Holes must be 4" apart horizontally. (See Figure
19)
2. Mark hole locations at each mounting location. (See Figure
19)
3. Drill two 1/2” holes at marked hole locations on stud. (See
Figure 19)
4. Drill two 1/2" holes on marked hole locations NOT on stud.
(See Figure 19)
Figure 19
5. Hold metal channel on anchor (L) flat alongside plastic
straps and slide channel through hole. (See Figure 20)
Figure 20
6. Holding plastic straps on anchor (L), pull anchor away from
wall until channel rests flush behind wall making sure
anchor channel is positioned vertically on stud. (See Figure
21)
7. Slide plastic cap on anchor (L) towards wall until flange of
cap is flush with wall. (See Figure 21)
Figure 21
8. Snap off plastic straps on anchor at wall by pushing side to
side, snapping off straps level with flange of plastic cap.
(See Figure 22)
Figure 22
9. Repeat Steps 5 through 8 for the other mounting holes.
X
X
X
X
5 5/8” above
finished floor
32 5/8” above
finished floor
4
” apart
4” apart
1/2"
on stud 1/2"
(not on stud)
34
(L)
Drywall
Plastic Straps
5
(L)
Plastic Cap
Drywall
Anchor Metal Channel
SIDE VIEW
6
Steel Stud
7
Plastic Straps
Drywall
Anchor Metal Channel
Plastic Cap
SIDE VIEW
8
Steel Stud
Installation Instructions LFE1U
15
10. Place wall brackets (B1) over anchors and align mounting
slots on mount with holes in anchors. (See Figure 23)
11. Install four 5/16-18 x 3 3/4" Phillips pan machine screws (M)
through 3/16 washers (N) and slots on wall bracket (B1) and
into toggler anchors (L). (See Figure 23)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Overtightening of
mounting hardware can damage the steel studs. DO NOT
overtighten mounting hardware!
12. Position column assembly (P) inside two installed wall
brackets (B1). (See Figure 23)
Figure 23
13. Install four 5/16 x 1/2” button head cap screws (X) through
slots on wall brackets (B1) and side of column assembly (P).
(See Figure 24)
Figure 24
Installing to a Concrete Wall
1. Measure 5 5/8" off the finished floor to mark lower mounting
locations and 32 5/8" off the finished floor for upper
mounting locations. Holes must be 4" apart horizontally.
2. Mark hole locations at each mounting location. (See Figure
25)
3. Drill four 3/8” holes at marked hole locations. (See Figure
25)
Figure 25
4. Install four concrete anchors (R) into drilled holes. (See
Figure 26)
5. Use four 5/16 x 2 3/4" flange head screws (Q) to secure two
wall brackets (B1) to wall. (See Figure 26)
Figure 26
11
(M) x 4
(N) x 4
12
(X) x 4
13
(P)
X
X
X
X
5 5/8” above
finished floor
32 5/8” above
finished floor
4
” apart
4” apart
3/8"
3
5
(Q) x 4
(R) x 4
4
LFE1U Installation Instructions
16
6. Install four 5/16 x 1/2” button head cap screws (X) through
slots on wall brackets (B1) and side of column assembly (P).
(See Figure 27)
Figure 27
Securing with Hardware to Floor (Optional)
The LFE1U can be mounted to the floor for additional support
and security, however it CANNOT be installed to the floor ONLY
without being also attached to a wall. No hardware is provided
for supplemental mounting to the floor.
Display Installation
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the weight of all
components attached to the LFE1U does not exceed 200 lbs
(90.7 kg).
1. Make sure height is at the lowest possible position.
2. Make sure latching flags are in "open" position.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware. Only use hardware provided or specified by
manufacturer.
3. Determine and mark the vertical center position between
the Left side Upper and Lower mounting holes in display.
(See Figure 28)
4. Determine and mark the vertical center position between
the Right side Upper and Lower mounting holes in display.
(See Figure 28)
Figure 28
5. Orient vertical mounting bracket (WR) so that mounting
holes are on top and mounting slots are on bottom. (See
Figure 28)
6. Align mounting holes in vertical mounting bracket (WR) with
upper and lower mounting holes in display.
7. Adjust vertical mounting bracket (WR) position until mark
made in Step 1 aligns with center mark in vertical mounting
bracket (WR).
8. Select correct screws, nesting spacers (if necessary) and
universal washers (if required) from the hardware bag (WA-
WM) and attach brackets to back of screen. (See Figure 30)
IMPORTANT ! : The M8 screws do NOT require a
washer. Use the universal washer (WMB) only with M4,
M5 and M6 screws.
NOTE: The nesting spacers (WMA) may be used separately,
or put two together in different configurations to create
different size spacers. (See Figure 29)
Figure 29
(X) x 4
6
(P)
for 1/4" screws (not included)
for 5/16" anchors (not included)
6
3
(TR) x 2
Mounting holes
Mounting Slots
(Single) (Nested) (Stacked)
0.375
[9.5]
0.563
[14.3]
0.750
[19.1]
Installation Instructions LFE1U
17
Figure 30
10
8
(WR) x 2
(WMA) x 4
(WA through WL)
x 4
(WMB) x 4
(WR)
9. If the display has a recessed mounting surface, protrusions
or a power box, a spacer and longer mounting hardware
must be placed between the display and vertical mounting
bracket (WR). (See Figure 30)
10. Repeat Steps 5 through 8 for Right side vertical mounting
bracket using the same hole locations to align brackets
horizontally.
11. Determine and mark the horizontal center position between
the Left and Right TOP mounting holes in display.
(See Figure 31)
12. Determine and mark the horizontal center position between
the Left and Right BOTTOM mounting holes in display. (See
Figure 31)
13. Orient upper horizontal mounting bracket (WQ) so that
flanges are facing towards display and resting in recessed
area of left and right vertical mounting brackets (WR). (See
Figure 31)
14. Adjust Upper horizontal mounting bracket (WQ) position
until center diamond in horizontal mounting bracket (WU)
aligns with mark made in Step 11, and mounting holes and
slots in horizontal mounting bracket (WQ) are aligned with
threaded holes in mounting tabs of left and right vertical
mounting brackets (WR). (See Figure 31) and (See Figure
32)
15. Use 1/8" hex key (WP) to secure upper horizontal mounting
bracket (WQ) to left and right vertical mounting brackets
(WR) using four button head flanged screws (WN). (See
Figure 32)
16. Repeat Steps 12 through 15 for lower horizontal mounting
bracket (WQ).
IMPORTANT ! : The orientation of, and mounting holes used,
when installing the lower horizontal mounting bracket must be
the same as the upper horizontal mounting bracket. Vertically
align upper and lower brackets by aligning holes or end of slots.
(See Figure 32)
IMPORTANT ! : Whenever possible install mounting
screws diagonally as shown in detail in Figure 32.
17. Install display with attached universal interface to mount
following the installation instructions provided with the
mount.
Figure 31
12
11
(WR) x 2
Center Mark
(WQ) x 2
LFE1U Installation Instructions
18
Figure 32
15
15
(WQ) x 2
(WR) x 2
(WN) x 8
(WR) x 2
14
18. Make sure latching flags are in "closed" position prior to
using cart!
IMPORTANT ! : Manufacturer recommends using cable
ties (K) to secure the latching flags in closed position on
both sides if padlock is not being used. (See Figure 33)
Figure 33
Adjustments
Height Adjustment
1. Press "UP" or "DOWN" buttons to raise or lower height as
desired. (See Figure 34)
Figure 34
Save Height Levels
1. Adjust height until desired preset level is reached using
"UP" and "DOWN" buttons. (See Figure 34)
2. Press "SAVE" button. (See Figure 34)
3. Press one of three preset buttons (., .. or ...) to save preset
position. (See Figure 34)
4. Repeat Steps 1-3 as desired.
(K) x 2
"UP" "DOWN" "PRESETS" "SAVE"
Installation Instructions LFE1U
19
Tilt Adjustment
IMPORTANT ! : Remove display from mount prior to
adjusting tilt!
5. Use 3/16" hex key (H) to remove tilt adjustment screws on
both sides. (See Figure 35)
6. Adjust faceplate tilt and re-install removed screw in either
the middle hole for 2° tilt or the lowest hole for 4° tilt. (See
Figure 35)
Figure 35
Roll Adjustment
7. Loosen nuts on back of faceplate. (See Figure 36)
8. Adjust roll as desired. (See Figure 36)
9. Tighten nuts on back of faceplate. (See Figure 36)
Figure 36
Troubleshooting
If lifting function does not work properly, try to following
troubleshooting steps. If none of these work, contact customer
service.
1. If there is uneven movement, initialize the control box
(reset)
• Hold "Down" button until lift has reached it’s lower
limit.
• Briefly release "Down" button
• Press and hold "Down" for five seconds, wait until
all movement has stopped, then release
2. If there is no movement, check the following
• Check all cable connectors between controllers
and actuators.
• Check power cable connection to control box.
3. If there is slight movement and then reverse travel, check
for any obstructions that may be interfering such as cables
or peripheral devices.
4. Contact customer service if none of the above steps fix the
problem.
5
66
2°
4°
remove
re-install
(rear view)
8
79
LFE1U Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003128 Rev01
2020 Legrand | AV
www.legrandav.com
01/20