Chief LSA1U User Manual
Displayed below is the user manual for LSA1U by Chief which is a product in the Signage Display Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
MTA1U
MSA1U
LSA1U LTA1U
FUSION MEDIUM AND LARGE
FLAT PANEL MOUNTS
Spanish Product Description
German Product Description
MSA1U/MTA1U/LSA1U/LTA1U
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provi de for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone A V Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WA RNING alerts you to the possibility of
serious injury or death if you do not follow the instructions .
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using th e instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components and accessories attached to the MSA1U/
MTA1U does not exceed 125 lbs (56.7 kg), OR 200 lbs (90.7
kg) for the LSA1U/LTA1U.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mounting system outdoors.
IMPORTANT ! :
The MSA1U/MTA1U/LSA1U/LTA1U mounts
are designed to be mounted to :
• a bare 8" concrete or 8"x8"x16" concrete block wall;
• a 2" x 4" wood stud wall covered by drywall with
maximum thickness of 5/8":
•MSA1U/MTA1U: Wood studs must be 16" on
center;
•LSA1U/LTA1U: Wood studs may be 16" or 24" on
center.
--SAVE THESE INSTRUCTIONS--
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U
3
DIMENSIONS
6.00
152.4
1. MAXIMUM MOUNTING PATTERN IS 22.25" (565 mm) WITHOUT REVERSING UPRIGHTS
2. MAXIMUM MOUNTING PATTERN IS 25.6" (650 mm) WITH REVERSING UPRIGHTS
3. FOR RECESSED APPLICATION S , MINIMUM VERTICAL LIFT FOR HO OK
ENGAGEMENT IS .75" (19 mm)
RAILS CAN BE SLID LEFT OR RIGHT
FOR OFFSET
MTA1U
DIMENSIONS: INCHES
[MILLIMETERS]
6.00
152.4
RAILS CAN BE SLID LEFT OR RIGHT
FOR OFFSET
1. MAXIMUM MOUNTING PATTERN IS 22.7" (576 mm) WITHOUT REVERSING UPRIGHTS
2. MAXIMUM MOUNTING PATTERN IS 25.3" (642 mm) WITH REVERSING UPRIGHTS
3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
ENGAGEMENT IS .75" (19 mm)
DIMENSIONS: INCHES
[MILLIMETERS]
MSA1U
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions
4
DIMENSIONS--continued
15.00
381.0
14.00
355.6
0.34
8.7
1.00
25.4
1.25
31.8
6.00
152.4
1.45
36.9
1.72
43.8
16.00
406.3
MINIMUM UPRIGHT SPACING
20.50
520.7
7.00
177.8
2.07
52.5
RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET
34.00
863.6
34.75
882.7
1.99
50.6
7.00
177.8
2.75
69.9
1.48
37.5
19.69
500.0
0.49
12.5
0.34
8.7
9.84
250.0
1. M AXIMUM MOUNT IN G PA T TERN IS 34.3" (871 mm) WITH OUT REVERSING UP RIGHTS
2. M AXIMUM MOUNT IN G P ATTERN I S 31.7" (805 mm) WITH RE VE RSING UP RIGHT S
3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
ENGAGEM ENT IS .75" (19 mm)
LSA1U
DIMENSIONS: INCHES
[MILLIMETERS]
16.00
406.3
MINIMUM UPRIG HT SPACING
6.00
152.4 1.25
31.8
1.00
25.4
0.34
8.7
15.00
381.0
14.00
355.6
7.00
177.8
1.63
41.3
2.59
65.9
2.07
52.5
R A ILS CA N B E SLID LEFT OR RIGHT
FO R OFFSET
34.00
863.6
34.75
882.7
2.00
50.9
20.50
520.7
7.00
177.8
2.75
70.0
12°
0.34
8.7
0.49
12.5
19.69
500.0
2 X 3.44
87.5
1.48
37.5
9.84
250.0
1. MAXIMUM MOUNTING PATTE RN IS 31.25" (794 mm) WITHO UT RE V E R SING UPRIG HTS
2. M A X I M U M M OUNT IN G PA T TERN IS 34.6" (879 mm) WITH REVE RSING UPRIGHTS
3. FOR RECESSE D AP P LICATIONS, MINIMUM VERT ICAL LIFT FO R H OOK
E N GAGEMENT IS . 75" (19 mm)
LTA1U
DIMENSIONS: INCHES
[MILLIMETERS]
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32" (5.5mm) Wood Stud
#2
3/8" (9.5mm) Concrete 3/16" x 10"
(included)
C (4) E (4)
A (4)
M4x12mm B (4)
M4x20mm M4x25mm D (4)
M5x12mm M5x20mm F (4)
M5x25mm
G (4)
M6x12mm
H (4)
M6x20mm
LSA1U
[Interface brackets]
Universal Hardware Kit
I (4)
M6x25mm K (4)
J (4)
M8x12mm M8x20mm L (4)
M8x30mm
MA (8)
[Nesting MB (4)
[Universal washer]
Wall Mounting Hardware Kit
N (4)
5/16 x 2-1/2"
P (4)
UX10x60mm
Q (4)
[Slotted
washer]
MSA1/LSA1 Mount Hardware Kit
R (1)
3/16"
S (2)
3/8-16 x 3/4"
MTA1/LTA1 Mount Hardware Kit
R (1)
3/16" S (2)
3/8-16 x 3/4"
T (2)
1/4-20 x 1"
U (2)
1/4-20
V (1) W (1)
[left] [right] X (1) Y (1)
[left] [right]
LTA1U
[Interface brackets]
Z (1)
[MSA1U/MTA1U
mount]
Z (1)
[LSA1U/LTA1U
mount]
OR
spacer]
[Included in hardw are box ]
[Included in hardware box]
[Included in hardware box]
MSA1U
V (1) W (1)
[left] [right]
MTA1U
X (1) Y (1)
[left] [right]
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U
7
INSTALLATION
The MSA1U/MTA1U/LSA1U/LTA1U mounts are designed to be
mounted to a bare 8" concrete, 8"x8"x16" concrete block; or
2" x 4" wood studs (16" on center for MSA1U/MTA1U , an d 16"
or 24" on center for LSA1U/L T A1U) wall covered by drywall with
5/8" maximum thickness.
The MTA1U and LTA1U have brackets which allow the TV to be
tilted. The MSA1U and LSA1U have static brackets which keep
the TV in an upright position.
Locate Mounting Site
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE T O EQUIPMENT! It is the installers responsibility
to make certain the structure to which the mount is being
attached is capable of supporting five times the combined
weight of all components located on the mou nt, not to exceed
125 lbs (56.7 kg) for the MSA1U/MTA1U,
OR
200 lbs (90.7 kg)
for the LSA1U/LTA1U.
NOTE: Proceed to either the Installing to a Wood Stud Wall
section or the Installing to a Concrete Wall section.
Installing to a Wood Stud Wall
1. Determine the center of the TV screen, and where it should
be located on th e wall.
2. Locate the closest stud to the left and right of the selected
location.
NOTE: If the screen area lies over a stud, use that stud and the
stud to either the left or right of it.
3. Line up the diamond shapes on mo unt (Z) with center of
screen marking to determine vertical center. (See Figure 1)
4. Measure up 7" (177.8mm) from the center point to mark
location of the upper mounting slots. (See Figure 1)
Figure 1
5. Using a level, mark the wall on each stud to attach the
mount through the upper mounting slots. (See Figure 2)
6. Drill one 7/32" (5.5mm) pilot hole in each stud.
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (N) into
pilot holes but do not tighten to wall.
8. Hang mount (Z), aligning upper mounting slots over lag
bolts and adjust side-to-side for proper location.
9. Place one slotted washer (Q) over each flanged lag bolt.
(See Figure 2)
10. Tighten lag bolts to secure mount (Z) to wall at upper
mounting slots.
Figure 2
11. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 2)
12. Drill 7/32" (5.5mm) pilot holes at markings for lower
mounting holes. (See Figure 2)
13. Use two 5/16 x 2-1/2" flanged lag bolts (N) and two 5/16"
slotted washers (Q) to attach the mount to the wall through
the lower mounting holes. (See Figure 2)
14. Slide rails to approximate center of screen location.
15. Proceed to Attaching Interface Brackets to Screen
section.
Center of screen
Vertical center
of mount
(MSA1U shown)
7"
(177.8mm)
11 12
56
7
10
(N) x 2
(Z)
9
(Q) x 2
13
(N) x 2
13
(MSA1U shown)
(Q) x 2
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions
8
Installing to a Concrete Wall
1. Determine the center of the TV screen, and where it should
be located on th e wall.
2. Line up the diamond shapes on mount (Z) with center of
screen marking to determine vertical center. (See Figure 1)
3. Measure up 7" (177.8mm) from the center point to mark
location of the upper mounting slots.
4. Using a level, mark the wall through both upper mounting
slots. (See Figure 3)
Figure 3
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 16" (406.4mm). Do not
place mounting brackets closer together than 16" (406.4mm).
5. Drill one 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot hole at each
marking.
6. Install an anchor (P) into each pilot hole using a hammer,
making sure that the anchor is flush with the wall.
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (N) in to
pilot holes but do not tighten to wall.
8. Hang mount (Z), aligning upper mounting slots over lag
bolts and adjust side-to-side for proper location.
9. Place one slotted washer (Q) over each flanged lag bolt.
(See Figure 3)
10. Tighten lag bolts to secure mount (Z) to wall at upper
mounting slots.
11. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 3)
12. Drill 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot holes at markings
for lower mounting holes. (See Figure 3)
13. Use two 5/16 x 2-1/2" flanged lag bolts (N) and two 5/16"
slotted washers (Q) to attach the mount to the wall through
the lower mounting holes. (See Figure 3)
14. Slide rails to approxima te center of screen location.
Attaching Interface Brackets to Screen
1. Align the center of the bracket (V and W or X and Y) with
center of screen. (See Figure 4)
NOTE: The diamond-shape holes in the bracket correspond to
the center of the mount.
Figure 4
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2. Select correct screws, nesting spacers (if necessary) and
universal washers (if required) from the hardware bag (A-M)
and attach brackets to back of screen. (See Figure 4)
IMPORTANT ! : The M8 screws do NOT requir e a
washer. Use the universal washer (MB) only with M4, M5
and M6 screws.
11
5
64
12
x 4
(P) x 4
10
7
10
(N) x 2
(Q) x 2
9
(Q) x 2
13
13
(MSA1U/MTA1U shown)
(N) x 2
Center of bracket
Pull cord
[Brackets V and W shown]
(MA) (A-L)
(MB)
(MSA1U shown)
NOTE: Use universal washer (MB) ONLY with M4, M5
and M6 screws.
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U
9
NOTE: The nesting spacers (MA) may be used separately, or
put two together in different configurations to create
different size spacers. (See Figure 5)
Figure 5
Switching Interface Brackets (Optional)
If an installation situation makes adjusting the location of
interface brackets necessary, there are several options.
1. The wall brackets may be adjusted side to side at the point
of attachment. (See Figure 6)
2. The location of the left and right interface brackets (V and W
or X and Y) may be switched, with the knobs on the MT A1U/
LTA1U interface brackets (X and Y) facing the inside of the
mount. (See Figure 6)
Figure 6
3. If necessary, the tilt interface bracket knobs may be
switched to allow the interface brackets (X and Y) to be
reversed. (See Figure 7)
a. Remove display from mount.
b. Remove interface brackets from display.
c. Hold the right in t erf ace bracket horizon tally, tightly
gripping it so that spacers do not move.
d. Remove the knob and screw.
e. Replace the knob and screw in the opposite order, with
the knob on the inside of the bracket.
f. Switch the right interface br acket to the left side of the
wall mount.
g. Repeat Steps 3c through 3f with the left interface
bracket.
Figure 7
(Single) (Nested) (Stacked)
0.375
[9.5]
0.563
[14.3]
0.750
[19.1]
1
2
Knobs
[Brackets X and Y shown]
(MTA1U shown)
3e
Knobs to outside
of brackets
[Brackets X and Y shown]
3d
(MTA1U shown)
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions
10
Attaching Screen to Wall Mount
NOTE: NEVER place both interface brackets (V and W or X
and Y) to one side of the wall mount center line! (See
Figure 8)
NOTE: Do NOT allow both interface brackets (V and W or X
and Y) to be located on same side of wall bracket. (See
Figure 8)
Figure 8
Both interface brackets must NEVER be located
to one side of the wall brackets!
NEVER place both interface brackets to one
side of the wall mount center line (CL)!
Center Line (CL)
[Brackets V and W shown]
(MSA1U show n)
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U
11
1. Hang screen onto the top rail of the mount (CC). (See
Figure 9)
•
MSA1U / LSA1U:
Hang top hook of interface brackets (V
and W) onto the top rail of the mount (Z). (See Figure 9)
• MTA1U / LTA1U: Move latch on top of interface
bracket to OPEN position and hang top hook of
interface brackets (X and Y) onto the top rail of the
mount (Z). (See Figure 9)
NOTE: The screen initia lly installs into the "service mode" to
allow easy cable access.
2. Adjust screen and rails to desired view ing position.
3. Route cables between wall and rails.
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
4. Pull downward on the pull cords and swing inward toward
wall, latching interface brackets to lower rail and fastening
bottom of screen to the mount. (See Figure 9)
5. Attach end of pull cord (a magnet) to mount so it does not
extend beyond bottom of screen. (See Figure 9)
Figure 9
5
Pull
1
Top
Hook
cords
(MSA1U shown) (MTA1 U shown)
Latch in
5
Pull
cords
4
4
4
4
1
OPEN
position
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions
12
Adjustments
Horizontal Adjustment
1. The mount wall brackets may be adjusted side to side at the
point of attachment. (See F igure 10)
Figure 10
2. The screen may also be adjusted alo ng rails side to side.
NOTE: NEVER place both interface brackets (V and W or X
and Y) to one side of the wall mount center line! (See
Figure 8)
NOTE: Do NOT allow both interface brackets (V and W or X
and Y) to be located on same side of wall bracket. (See
Figure 8)
3. (MTA1U / LTA1U only) Move latch on top of interface
brackets to CLOSED position. (See Figure 11)
Tilt (MTA1U / LTA1U Only)
The interface brackets (X and Y) allow from -2° to 12° tilt, and
can be locked at 0°, 6° and 12°.
1. Loosen the interface bracket knob.
2. Adjust tilt as required. (See Figure 11)
3. The tilt may be locked at 0°, 6° or 12° using one 1/4-20 x 1"
round head carriage bolt (T) and one 1/4-20 hex nut (U) per
interface bracket. (See Figure 11)
4. Tighten interface bracket knob.
Figure 11
1" (25.4mm) horizontal
1
adjustment possible
Latch in
CLOSED
position
3
(U)
(T)
2
Lock at 12° tilt
Lock at 6° tilt
Lock at 0° tilt
Interface
bracket
knob
(MTA1 U shown)
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U
13
Locking Screen Interface Brackets (Optional)
1. Lock screen interface brackets onto mount rails using one
3/8-16 x 3/4" set screw (S) on each interface bracket. (See
Figure 12)
Figure 12
Locking Mount (Optional)
1. Add padlock (not included) to interface bracket to complete
security. (See Figure 13)
NOTE: The padlock maximum shackle diameter is 5/16"
(7.9 mm).
Figure 13
(MSA1U shown)
1
1
(S) x 2
(back view)
(S) x 2
(MTA1U shown)
(front view)
1
(MSA1U shown)
Padlock shackle
- 5/16" (7.9mm)
maximum diameter:
1
Padlock shackle
- 5/16" (7.9mm)
maximum diameter:
(MTA1U shown)
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions
14
Installation Instructions MSA1U/MTA1U/LSA1U/LTA1U
15
MSA1U/MTA1U/LSA1U/LTA1U Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Stree t
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002852 Rev00
2016 Milestone AV Technologies
www.milestone.com
05/16