Chief LVS1UP User Manual
Displayed below is the user manual for LVS1UP by Chief which is a product in the Signage Display Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
LVS1UP LVSXUP
ConnexSys™ Portrait Video Wall Mounting System
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
LVS1UP / LVSXUP
LVS1UP / LVSXUP Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provi de for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief®, ConnexSys™, RapidDraw™, and PowerZone™ are
trademarks of Milestone AV Technologies. All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions .
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the LVS1UP/LVSXUP does not
exceed maximum weights listed in table below.
IMPORTANT ! : The video wall system ships either with rails
(LVS1UP) or without (LVSXUP). If you’re installing a video wall
of LVSXU P mounts you will need to provide th e strut channel
for mounting to the wall. (See LET’S GET STARTED!
Measurements You’ll Need section for further information.)
IMPORTANT ! : The LVS1UP/LVSXUP is designed to be
mounted to:
• a bare 8" thick solid concrete wall. Fasteners must be
placed a minimum of 16" (406mm) and a maximum of
24" (610mm) apart AND within 4" (102mm) of each end
of the rail/strut channel.
• a 5/8" minimum thickness plywood-backed, steel stud
wall covered with drywall having a maximum thickness
of 5/8". Five fasteners must be evenly spaced in the
top rail/strut channel along the width of the display with
at least 3-1/2" (89mm) spacing between each fastener
AND within 3-1/2" (89mm) from each end of rail/strut
channel. Repeat to secure bottom rail/strut channel.
• a 2" x 4" wood stud wall covered with drywall having a
maximum thickness of 5/8". Fasteners must be placed
a minimum of 16" (406mm) and a maximum of 24"
(610mm) apart AND within 4" (102mm) of each end of
the rail/strut channel.
NOTE: For installation on a curved wall, the wal l radius must
be greater than 200" (508cm).
--SAVE THESE INSTRUCTIONS--
MODEL Maximum Weight Allowed
LVS1UP 150 lbs
(68.0 kg)
LVSXUP 150 lbs
(68.0 kg)
Installation Instructions LVS1UP / LVSXUP
3
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .....................................2
TABLE OF CONTENTS ...............................................................3
LEGEND ......................................................................................4
DIMENSIONS ..............................................................................5
TOOLS REQUIRED FOR INSTALLATION .................................6
PARTS .........................................................................................6
LET’S GET STARTED! Measurements You’ll Need ....................7
MOUNTING PATTERN OFFSET CALCULATION ......................8
STRUT CHANNEL REQUIREMENTS (LVSXUP) .......................8
CURVED VIDEO WALLS ON FLAT WALL ..................................9
Calculating Wall Radius......................................................9
ALLOWING SPACE FOR MOUNT ADJUSTABILITY...................9
ATTACHING STRUT CHANNEL OR RAIL .................................10
HANGING LVS1UP/LVSXUP MOUNT ON RAIL/STRUT CHANNEL.. 11
Preparing Strut Channel (LVSXUP only) ................11
Hanging Mounts .....................................................11
INSTALLING INTERFACE BRACKETS ......................................12
ADDING DISPLAYS TO MOUNTS ..............................................12
ADJUSTMENTS ..........................................................................13
COMPLETING THE INSTALLATION ..........................................15
Cable Management Clips .......................................15
Security ...................................................................15
SERVICE .....................................................................................15
Extending and Retracting Mount ............................15
Interface Bracket Kickstands ..................................15
RapidDraw Display Release ...................................16
FASTENER INSTALLATION METHODS ....................................16
Wood Stud ..............................................................16
Concrete .................................................................16
Plywood-Backed Steel Stud ...................................17
LVS1UP / LVSXUP Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions LVS1UP / LVSXUP
5
DIMENSIONS
15.75
400.0
MAX DISPLAY
PATTERN WIDTH
31.50
800.0
MAX DISPLAY
PATTERN HEIGHT
32.50
825.4
1.00
25.4
HEIGHT
ADJUST
4.09
103.9
MIN DEPTH
BACK TILT
LVS1UP
DIMENSIONS: INCHES
[MILLIMETERS]
15.75
400.1
MAX DISPLAY
PATTERN WIDTH
31.50
800.0
MAX DISPLAY
PATTERN HEIGHT
32.50
825.4
1.00
25.4
HEIGHT
ADJUST
4.09
103.9
MIN DEPTH
BACK TILT
RAILS NOT INCLUDED IN LVSXUP VERSION. 13/16” RAILS SHOWN
FOR DEPTH AND POSITION MEASUREMENTS ONLY. IF USING
DEEPER STRUT CHANNEL ADD IN THE ADDITIONAL DEPTH.
DIMENSIONS: INCHES
[MILLIMETERS]
LVSXUP
LVS1UP / LVSXUP Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
nut driver 7/16"
1/2"
7/16"
1/2"
7/16"
1/2" 1/8" x 6"
(included)
3/8"
3/8"
7/32"
3/8"
(Letters correspond to letters on bag)
A (4)
M6 x 12 B (4)
M6 x 16 C (4)
M6 x 30 D (4)
3/16"
E (4)
.75x.344x.5
F (4)
M8 x 12 G (4)
M8 x 16
H (4)
M8 x 25
J (4)
UX10 x 60
K (4)
5/16"
L (4)
5/16" x 2-1/2"
M (10)
N (10)
#14 x 1-1/2"
1/4" Q (4)
[Cable clip]
P (8)
[7-1/2" cable tie]
U (1)
V (1)
[Rail]
[LVS1UP assembly]
X (2)
[Interface
bracket]
OR
U (1)
[LVSXUP assembly]
(LVS1UP only)
R (2)
[Outer stop
S (2)
T (2)
1/4-20 x 1/2"
W (1)
1/8" x 6"
(LVSXUP only)
Cable Management Kit
Display Hardware Kit Concrete and Wood St ud Walls
Install Hardware Kit
Plywood-backed Walls
Install Hardware Kit
clamp]
[Inner stop
clamp]
PowerZone™ Adjustment Guide
Y (1)
[Label sheet]
Z (1)
Installation Instructions LVS1UP / LVSXUP
7
LET’S GET STARTED!
Table 1: Measurements You’ll Need
* Check with your local strut channel dealer to determine th e lengths available. You may need to buy multiple pieces or cut longer
pieces down to size.
Figure 1
Description Measurement
A - Number of displays in each row
B - Number of displays in each column
C - Width of individual display
D - Height of individual display
E - Total width - (A) x (C)
F - Floor to bottom of display (bottom row) OR Ceiling to top of display
(top row)
G - 1/2 height of display (D) / 2
H - Display mounting pattern offset. Only applies to some displays.
Calculation instructions (See Figure 2)
I - Strut channel length* (E) – 4" (102mm) (LVSXUP only)
J - Number of strut channel lengths ( B) x 2 (LVSXUP only)
R - Radius of curved wall (Curved wall installations only)
I
C
D
E
G
FLOOR
CEILING
F
F
LVS1UP / LVSXUP Installation Instructions
8
MOUNTING PATTERN OFFSET CALCULATION
Figure 2
STRUT CHANNEL REQUIREMENTS (LVSXUP)
IMPORTANT ! : Strut channel must be made of steel with a minimum yield strength of 33ksi (230MPa), OR aluminum
(6063-T6, 6005-T5 or stronger) with a minimum yield strength of 30ksi (207MPa), and meeting the profile and dimension
requirements outlined in Table 2, dependent on whether it is a flat wall or curved wall installation. (See Figure 3) and (See
Figure 4) Table 2: Strut Channel Material and Dimension Requirements
STRUT REQUIREMENTS
MATERIAL ALUMINUM STEEL
Minimum Y i eld Strength 30ksi (207MPa) 33ksi (230 MPa)
Material Thickness [0.078"] (2mm) 14 ga [0.075"] (2mm)
or 12ga [0.104"] (2.5mm)
K (Flat wall) 13/16" (21mm) or 7/8" (22mm) 13/16" (21mm) < K < 3-1/4" (83mm)
K (Curved wall) 13/16" (21mm) or 7/8" (22mm)
R - Minimum Wall Radius > [200"] (50.8m) > [400"] (101.6m)
L - Flange Length 1/4" (6mm) < L < 9/32" (7mm)
Center line of
display
Center line
of mounting
pattern
Mounting
of display
pattern
Offset (H)
NOTE: An offset measurement (H) is required if the
centerline of the display does not match the centerl ine of the
display mounting pattern.
1. If display mounting pattern is BELOW display centerline:
8-3/4" - H = Distance from display centerline to rail/
2. If display mounting pattern is ABOVE display centerline:
8-3/4" + H = Distance from display centerline to rail/
strut channel mounting locatio n
strut channel mounting location
Figure 3 Figure 4
7/8" 3/8"
L
K
1-5/8"
IMPORTANT! All dimensions other than "L" and "K"
are nominal requirements.
(10mm)
(22mm)
(41mm)
Strut Channel Profile
UNACCEPTABLE strut channel profiles
Strut channel MUST have
rolled up lips on both sides
of channel.
Strut channel MUST NOT
have holes or slots on
side walls of channel.
Installation Instructions LVS1UP / LVSXUP
9
CURVED VIDEO WALLS ON FLAT WALL
• 5.5° is the maximum angle a mount can make from vertical;
• Two or more mounts placed side-by-side can create a maximum angle of 11° (on a flat wall);
• All other requirements/restrictions listed in Table 2 still apply.
CALCULATING WALL RADIUS
1. Place a rigid, flat stick or channel strut (at least 3 ft or 1m long, but preferably longer) against the curved wall. Do NOT bend the
stick or strut.
2. Measure the largest gap between the stick/strut and the wall.
Figure 5
EXAMPLE:
Stick/ Strut Length 48 inches
Gap 0.375 inches
Radius (R) 768.1875 inches
Radius = Gap/2 + (Length/8 x Length/Gap)
Radius = 0.375/2 + (48/8 x 48/0.375)
Gap
(view from above) Flat stick or strut
Curved wall
ALLOWING SPACE FOR MOUNT
ADJUSTABILITY
IMPORTANT ! : In order to enable the most adjustability
within the video wall, include some extra depth when
planning the installation.
As a rule of thumb, assume the mount is 4.5" deep and add
0.125" for every 10’ of displays [1"/120" x 0.125" = 0.00104"]
EXAMPLE: With a 4x3 Portrait video wall where the height is
48.9" x 3 and the width is 28.3" x 4. (See Figure 6):
•take the longest dimension (height) and multiply it
by 0.00104 (or 1"/120" x 0.125")
48.9" x 3 x 0.00104" = 0.153"
For this example, you would then install under the assumption
the depth will be 4.5" + 0.153".
Table 3: Depth Adjustment Factor
NOTE: The maximum mount thickness to design into the
installation is 7.00".
Figure 6
WALL
TYPE RADIUS DEPTH ADJUST
FACTOR
Flat walls N/A 0.00104" per inch
Curved walls
Radius >500"
0.0025" per inch
Curved walls 200"<Radius<500" 0.003 12" per inch
48.9"
28.3"
48.9" x 3 screens x 0.00104" (depth adjustment factor) = 0.153"
LVS1UP / LVSXUP Installation Instructions
10
ATTACHING STRUT CHANNEL OR RAIL
IMPORTANT ! : Reference measurements noted on
page 7.
1. Mark distance (F) from floor to desired location for bottom
of display OR from ceiling to desired location for top of
display (if installing top row first). (See Figure 1) and (See
Figure 7)
2. Mark dist ance (G) from bottom of display (or top of display)
to center line of display. (See Figure 1) and (See Figure 7)
3. Measure up 8-3/4" (222mm) from centerline of display and
mark location for top strut channel/rail attachment.
NOTE: If an offset measurement (H) is needed (See Figure 2):
• If display mounting pattern is BELOW display
centerline, measure up: 8-3/4" (222mm) - H
• If display mounting pattern is ABOVE display
centerline, measure up: 8-3/4" (222mm) + H
4. Level and attach strut channel/rail (V) using the provided
hardware. See Parts drawing, (See Figure 7) and (See
Table 4).
5. Mark dist ance (D) (up or down) from first strut channel/rail
slots and mark location of next row of strut channel/rail.
6. Repeat for remaining rows of strut channels/rails.
7. (LVSXUP only) Proceed to Hanging LVS1UP/LVSXUP
Mount On Rail/Strut Channel section.
8. (LVS1UP only) Measure over (C) (width of display) from
center of first installed rail, level and mark location of
adjacent rail. (See Figure 1) and (See Figure 7)
9. Repeat Step 8 for remaining rails in that row.
10. Attach upper rails (V) using Fastener Information. (See
Table 4)
11. Measure up from attached rails the distance (D) and mark
for next row of rails (V). (See Figure 1) and (See Figure 7)
12. Repeat Steps 4 - 10 for that row of rails.
13. Repeat Step 11 for any remaining rows of ra ils (V).
IMPORTANT ! : See Fastener Installation Methods section
at end of Installation Instructions for details on installing product
into various wall types.
Table 4: Fastener Information
WALL TYPE PILOT
HOLE FASTENERS (see PART S
drawing)
Drywall
attached to
plywood-
backed walls /
Steel studs
N/A #14 x 1-1/2" hex slot head screw (N)
& 1/4" washer (M). 5 fasteners must
be evenly spaced in the top rail/strut
channel along the width of the display
with at least 3-1/2" (89mm) spacing
between each fastener AND within 3-1/
2" (89mm) from each end of rail/strut
channel. Repeat for lower rail/strut
channel.
Wood stud
(2" x 4")
7/32" x 3"
5/16 x 2-1/2" hex head lag (L) & 5/
16" washer (K). Fasteners placed at
stud locations, min. 16" (400mm) and
max. 24" (610mm) AND within 4"
(102mm) of each end of the rail/strut
channel.
Concrete 3/8" x 3" 5/16 x 2-1/2" hex head lag (L) &
Fischer UX10x60 anchor (J).
Fasteners placed a min. 16" (400mm)
and max. 24" (610mm) apart AND
within 4" (102mm) of each end of the
rail/strut channel.
Figure 7
Top rail - LVS1U
Top strut channel - LVSXU
Ceiling
Centerline - display
Centerline - display
C
I
D
1
2
3
Floor
1
2
3
5
7
H
C
D
Installation Instructions LVS1UP / LVSXUP
11
HANGING L VS1UP/LVSXUP MOUNT ON RAIL/
STRUT CHANNEL
Preparing Strut Channel (LVSXUP only)
1. On the top rail, slide one inner stop clamp (S) into end of
strut channel section. (See Figure 8)
2. Fasten outer stop clamp (R) to inner stop clamp (S) using
one 1/4-20 x 1/2" hex head screw (T). (See Figure 8)
3. Repeat for each end of each top section of strut channel.
Figure 8
Hanging Mounts
1. Lift mount and hang it on lower lip of upper strut channel or
rail (V). (See Figure 9)
Figure 9
2. Repeat for remaining mounts in that row , and slide mounts
along rails/strut channel s to desired location.
3. LVSXUP only: Add lower strut channel to bottom of all
mounts in row by lifting strut channel up from below mounts
and setting upper lip of strut channel onto mounts’ latching
hooks. (See Figure 10)
Figure 10
4. Tighten two hex head fasteners at bottom of each mount.
(See Figure 11 )
Figure 11
5. Fasten bottom rail (LVS1UP) or lower strut channel
(LVSXUP) to wall using the provided hardware. See Parts
drawing, and (See Tabl e 4).
6. Extend RapidDraw pull cord to bottom row of displays so
that it is accessible, re-tie to correct length and label the pull
cord using label (Y) so that it is identifiable. (See Figure 11)
IMPORTANT ! : See Service section for more
information on properly configurating the RapidDraw cord
and display release.
7. Repeat Attaching Strut Channe l or Rail and Hanging
LVS1UP/LVSXUP Mount On Rail/Strut Channel sections
for each row of displays.
(R)
(S)
1
2
(T)
Stop clamp fastened
in place at each end
of upper row of
strut channel
(LVS1UP shown as example)
1
1
lower lip of strut
channel or rail
3
3
side
view
mount hooks
strut channel
upper lip
lower strut
channel
wall
4
x 2
RapidDraw
pull cord
LVS1UP / LVSXUP Installation Instructions
12
INSTALLING INTERFACE BRACKETS
1. Place displays face down on a soft, non-abrasive surface.
CAUTION: Using screws of improper diameter may
damage your display! Proper screws will easily thread into
display mounting holes.
2. Select screw diameter by examining hardware (A-C and F-H)
(6mm or 8mm) and comparing with mounting holes on
display. (See Figure 12)
3. Select spacers:
• Spacers are NOT required if mounting holes are not
recessed and interface brackets (X) can lay flat against
display.
•Spacers (E) ARE required if mounting holes are
recessed, or if protrusions prevent interface brackets
(X) from laying flat.
CAUTION: Using screws of improper le ngth may damage
your display! Proper screws will have adequate thread
engagement witho ut contacting bottom of display mo unting
holes.
4. Select screw length: (See Figure 12)
• By hand, insert SHORTEST length screw of selected
diameter (A or F) through 3/16" washer (D, if using
screw A), bracket (X), selected spacer (E, if required),
into display mounting hole. Do NOT thread screw into
hole at this time.
• Proper screw length requires base of screw head to
protrude above flat washer (if flat washer is used) a
distance equal to or greater than the screw diameter. If
screw length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
Figure 12
5. Make sure diamond on interface brackets is even with
center of display. (See Figure 12)
6. Use selected screws (A-C or F-H), washers (D, if using
screws A, B or C) and spacers (E), if necessary, to connect
interface brackets (X) to back of display. (See Figure 12)
ADDING DISPLAYS TO MOUNTS
1. Raise display with attached interface brackets and hook top
of brackets into top of mount. (See Figure 11)
2. Slowly bring bottom of display in towards mount until it clicks
into place.
3. Repeat Steps 1 and 2 for remaining mo unts in that row.
Figure 13
4. The displays can be easily removed by pulling both
interface bracket cords down. (See Figure 13)
5. Pull the bottom of the display out.
6. Lift up display to lift hooks off the mount.
6
(A-C or F-H) x 4
(D) x 4
(E) x 4, if
required
(X)
5
Match diamond
with center of
display
Bracket kickstand
may be raised to
allow hardware
attachment
Interface
bracket
hooked over
mount
(Display not shown)
(LVS1UP shown
as example)
1
1
5
4
5
Interface
bracket
cords
Installation Instructions LVS1UP / LVSXUP
13
ADJUSTMENTS
NOTE: The following steps are also referenced on the next
page (See Figure 18) and the PowerZone
Adjustment guide (Z).
1. Place the level against the front of the display and use knob
(#1 in Figure 18) to straighten the tilt. (See Figure 14)
Figure 14
2. Place a level on top of display and use the knobs at the top
of the interface brackets (#2 in Figure 18), to raise/lower
each side of display and level the display. (See Figure 15)
and (See Figure 18)
Figure 15
3. Place level across face of adjoining screens and adjust
depth (#3 in Figure 18) to make displays flush across the
front of the vi deo wall. (See Figu re 16 ) and (See Fi gure 18)
Figure 16
4. Slide latch mechanism until tab sits flush against the
interface bracket.
5. Pull tab forward to lock latch mechanism to interface
bracket. (See Figure 17)
6. Push latch down to engage the micro late ral adjustment
knobs (#4B and #4C in Figure 18). (See Figure 17) and
(See Figure 18)
7. Turn micro lateral adjustment knobs clockwise to move
display toward knob end until displays are in correct
position. (See Fig ure 18)
Figure 17
1
22
3
3
(Display not shown)
6
5
4
Tab
Latch Interface
bracket
Installation Instructions LVS1UP / LVSXUP
14
Figure 18
Tilt adjust
Height adjust
Depth adjust
Micro-lateral shift latch
Micro-lateral shift: Clockwise moves display towards knob end
Micro-lateral shift: Clockwise moves display towards knob end
Display release
Installation Instructions LVS1UP / LVSXUP
15
COMPLETING THE INSTALLATION
Cable Management Clips
1. Place cable clip (Q) into rail/strut channel and turn 90° in
either direction until cable clip is vertical. (See Figure 19)
2. Route cables and RapidDraw release cords along rails/strut
channels, through cable clips.
3. Fasten cables and cords to cable clips (Q) using cable ties
(P).
Figure 19
Security
The displays may be secured to the mounts by using a padlock
(not included) through the bottom of the interface brackets.
(See Figure 20)
NOTE: Padlock must have a 1/4" (6mm) shackl e diameter.
Figure 20
SERVICE
Extending and Retracting Mount
The mounts may be extended and retracted only in a service
situation.
1. To Extend Mount: Pull on the RapidDraw release cord
designated for the specific mount.
2. When the mount releases, carefully grasp bezel edges of
display and pull out slowly, being careful to clear
surrounding displays.
3. To Retract Mount: Carefully push against display bezel
edges, being careful to clear surrounding displays.
4. Push display against mount until it clicks into place.
Interface Bracket Kickstands
The interface brackets are equipped with kickstands which must
only be used in a service situation.
1. Pull down on interface bracket release cords. (See Figure 21)
2. Pull out bottom of display.
3. Flip down the kickstands on both interface brackets, and
prop against mount during service.
Figure 21
4. Af ter service, hold display while flipping up both kickst ands.
5. Slowly bring bottom of display in towards mount until it clicks
into place.
1
(Q)
Insert
padlock
Interface bracket
release cords
2
1
(Display not shown)
Kickstand
3
LVS1UP / LVSXUP Installation Instructions
16
RapidDraw Display Release
The RapidDraw pull cord and display rele ase allows easy
service access to any specific display in the video wall.
Each mount ships with the pull cord installed. It is installed so
that when pulled from below the mount or from the right of the
mount it will release the display for service.
The following steps should be taken if an installation requires
that the pull cord be accessible from the left of the display or
above the display:
1. Unhook the pull cord from the mount. (See Figure 22)
2. Reinstall the pull cord in the opposite hole on the mount.
(See Figure 22)
Figure 22
FASTENER INSTALLATION METHODS
IMPORTANT ! : (See Table 4) for appropriate hardware
and pilot hole sizes for various wall types.
Wood Stud
1. Use one 5/16" x 2-1/2" lag bolt (L) through product and into
pilot hole. (See Figure 23)
2. Repeat for remaining pilot holes.
Figure 23
Concrete
1. Inst all one UX10 x 60 anchor (J) into each pilot hole using a
hammer , making sure that the anchor is flush with the wall.
(See Figure 24)
2. Use one 5/16" x 2-1/2" lag bolt (L) through product into each
anchor in wall.
Figure 24
Mount ships with
cord attached here
2
To release display from
left or above,
reinstall cord
here
1
2
(L) x 2
1
2
(L)
(J)
LVS1UP / LVSXUP Installation Instructions
17
Plywood-Backed Steel Stud
1. Use one #14 x 1-1/2" hex-head washer slot head screw (N) and one 1/4" washer (M) through strut channel or rail. (See Figure 25)
Figure 25
Steel Stud (2 x 4 / 25ga minimum)
FRONT
There must be a minimum of
1-7/8" (48mm) clearance
inside wall
16" or 24" (on center) Studs
If back side of wall is unfinished, drywall must be installed
to a minimum of one stud left and right of the stud(s)
being used to install the mount. Drywall mu st be
secured to studs with screws a maximum of 12" (305mm) apart down center of stud.
Stud type and structural strength must conform to the North American
Specification for the Design of Cold-Formed S teel Structural Members.
5/8" maximum
drywall thickness
(Both Sides of Stud)
[362 S 125 18, C-Shaped, S-Stud Section]
Plywood
5/8" minimum thickness
plywood (5 layers) covered
with drywall having
maximum thickness of 5/8"
LVS1UP / LVSXUP Installation Instructions
18
Installation Instructions LVS1UP / LVSXUP
19
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
LVS1UP / LVSXUP Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002639 Rev02
2016 Milestone AV Technologies
www.milestone.com
05/16