Chief MTM1U User Manual
Displayed below is the user manual for MTM1U by Chief which is a product in the TV Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
LSM1U LTM1U
MSM1U MTM1U
FUSION HEIGHT ADJUST
FLAT PANEL MOUNTS
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
MSM1U / MTM1U /
LSM1U / LTM1U
MSM1U / MTM1U / LSM1U / LTM1U Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provi de for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARN ING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions .
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARN ING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using th e instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equip ment! It is the
installer’s responsibility to make sure the combined weight of
all components and accessories attached to the
MSM1U/
MTM1U does not exceed 125 lbs (56.7 kg); OR 200 lbs (90.7
kg) for the LSM1U/LTM1U.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mountin g system outdoors.
IMPORT ANT ! :
The MSM1U/MTM1U/LSM1U/L TM1U mounts
are designed to be mounted to:
• a bare 8" concrete or 8"x8"x16" concrete block wall, or
• a 2" x 4" wood studs wall covered by drywall with
maximum thickness of 5/8":
•MSM1U/MTM1U: Wood studs must be 16" on
center;
•LSM1U/LTM1U: Wood studs may be 16" or 24" on
center.
NOTE: The
MSM1U/MTM1U/LSM1U/LTM1U
Fusion height-
adjust mounts may be used with the UL Listed
FCAV1U Fusion pull-out accessory.
--SAVE THESE INSTRUCTIONS--
Installation Instructions MSM1U / MTM1U / LSM1U / LTM1U
3
DIMENSIONS
6.00
152.4
RAILS CAN BE SLID LEFT OR RIGHT
FOR OFFSET
1. MAXIMUM MOUNTING PATTERN IS 22.25" (565 mm) WITHOUT REVERSING UPRIGHTS
2. MAXIMUM MOUNTING PATTERN IS 25.6" (650 mm) WITH REVERSING UPRIGHTS
3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FO R HOOK
ENGAGEMENT IS .75" (19 mm)
MTM1U
DIMENSIONS: INCHES
[MILLIMETERS]
6.00
152.4
RAILS CAN BE SLID LEFT OR RIGHT
FOR OFFSET
1. MAXIMUM MOUNTING PATTERN IS 22.7" (576 mm) WITHOUT REVERSING UPRIGHTS
2. MAXIMUM MOUNTING PATTERN IS 25.3" (642 mm) WITH REVERSING UPRIGHTS
3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
ENGAGEMENT IS .75" (19) mm)
DIMENSIONS: INCHES
MSM1U
[MILLIMETERS]
MSM1U / MTM1U / LSM1U / LTM1U Installation Instructions
4
DIMENSIONS - continued
0,1,080:$//835,*+763$&,1*
5$,/6&$1%(6/,'/()7255,*+7
)252))6(7
7<3
7<3
0$;,08002817,1*3$77(51,6PP:,7+2875(9(56,1*835,*+76
0$;,08002817,1*3$77(51,6PP:,7+5(9(56,1*835,*+76
)255(&(66('$33/,&$7,2160,1,0809(57,&$//,)7)25+22.
(1*$*(0(17,6PP
DIMENSIONS: INCHES
LSM1U
[MILLIMETERS]
0,1,080:$//835,*+763$&,1*
5$,/6&$1%(6/,'/()7255,*+7
)252))6(7
;
7<3
0$;,08002817,1*3$77(51,6PP:,7+2875(9(56,1*835,*+76
0$;,08002817,1*3$77(51,6PP:,7+5(9(56,1*835,*+76
)255(&(66('$33/,&$7,2160,1,0809(57,&$//,)7)25+22.
(1*$*(0(17,6PP
DIMENSIONS: INCHES
[MILLIMETERS]
LTM1U
Installation Instructions MSM1U / MTM1U / LSM1U / LTM1U
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
MSM1U / MTM1U / LSM1U / LTM1U Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32" (5.5mm) Wood Stud
#2 3/8" (9.5mm) Concrete
1/8"
(included) 3/16" x 10"
(included)
C (4) E (4)
A (4)
M4x12mm B (4)
M4x20mm M4x25mm D (4)
M5x12mm M5x20mm
F (4)
M5x25mm G (4)
M6x12mm H (4)
M6x20mm
[Interface brackets]
Universal Hardware Kit
I (4)
M6x25mm K (4)
J (4)
M8x12mm M8x20mm L (4)
M8x30mm
MA (8)
[Nesting
MB (4)
[Universal washer]
Wall Mounting Hardware Kit
N (4)
5/16 x 2-1/2"
P (4)
UX10x60mm
Q (4)
[Slotted
washer]
X (4)
[Wall cover]
MSM1/LSM1 Mount Hardware
R (1)
1/8"
S (1)
3/16"
T (4)
1/4-20 x 3/4"
U (2)
3/8-16 x 3/4"
MTM1/LTM1 Mount Hardware
R (1)
1/8"
S (1)
3/16"
T (4)
1/4-20 x 3/4"
U (2)
3/8-16 x 3/4"
V (2)
1/4-20 x 1"
W (2)
1/4-20
Y (1) Z (1)
[left] [right]
AA (1) BB (1)
[left] [right]
LTM1U
[Interface brackets]
CC (1)
[MSM1U/MTM1U
mount]
CC (1)
[LSM1U/LTM1U
mount]
OR
spacer]
[Included in hardware box]
[Included in hardware box] [Included in hardware box]
MSM1U
Y (1) Z (1)
[left] [right]
LSM1U
AA (1)
[left] BB (1)
[right]
MTM1U
Installation Instructions MSM1U / MTM1U / LSM1U / LTM1U
7
INSTALLATION
The MSM1U/MTM1U/LSM1U/LTM1U mounts are designed to
be mounted to a bare 8" concrete, 8"x8"x16" concrete block; or
2" x 4" wood studs (16" on center for MSM1U/MTM1U, and 16"
or 24" on center for LSM1U/LTM1U) wall covered by drywall of
5/8" maximum thickness.
The MTM1U and LTM1U have brackets which allow the TV to
be tilted. The MSM1U and LSM1U have static brackets which
keep the TV in an upright position.
Locate Mounting Site
WARN ING:
IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE T O EQUIPMENT! It is the installers responsibility
to make certain the structure to which the mount is being
attached is capable of supporting five times the combined
weight of all components located on the mou nt, not to exceed
125 lbs (56.7 kg) for the MSM1U/MTM1U OR 200 lbs (90.7 kg)
for the LSM1U/LTM1U.
NOTE: Proceed to either the Installing to a Wood Stud Wall
section or the Installing to a Concrete Wall section.
Installing to a Wood Stud Wall
1. Determine the center of the TV screen, and where it should
be located on th e wall.
2. Locate the closest stud to the left and right of the selected
location.
NOTE: If the screen area lies over a stud, use that stud and the
stud to either the left or right of it.
3. Line up the notches on mount (CC) with center of screen
marking to determine vertical center. (See Figure 1)
4. Measure up 8" (203.2mm) from the center point to mark
location of the upper mounting slots.
Figure 1
5. Using a level, mark the wall on each stud to attach the
mount through the upper mounting slots. (See Figure 2)
6. Drill one 7/32" (5.5mm) pilot hole in each stud.
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (N) into
pilot holes but do not tighten to wall.
8. Hang mount (CC), aligning upper mounting slots over lag
bolts and adjust side-to-side for proper location.
9. Place one slotted washer (Q) over each flanged lag bolt.
(See Figure 2)
10. Tighten lag bolts to secure mount (CC) to wall at upper
mounting slots.
Figure 2
11. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 2)
12. Drill 7/32" (5.5mm) pilot holes at markings for lower
mounting holes. (See Figure 2)
13. Use two 5/16 x 2-1/2" flanged lag bolts (N) and two 5/16"
slotted washers (Q) to attach the mount to the wall through
the lower mounting holes. (See Figure 2)
14. Slide rails to approximate cente r of screen location.
15. Proceed to Locking Rails section.
Center of scree n
8"
Vertical center
of mount
(203.2mm)
(MSM1U shown)
11 12
56
(Q) x 2
7
10
(N) x 2
(CC)
9
(Q) x 2
13
(N) x 2
13
(MSM1U shown)
MSM1U / MTM1U / LSM1U / LTM1U Installation Instructions
8
Installing to a Concrete Wall
1. Determine the center of the TV screen, and where it should
be located on th e wall.
2. Line up the notches on mount (CC) with center of screen
marking to determine vertical center. (See Figure 1)
3. Measure up 8" (203.2mm) from the center point to mark
location of the upper mounting slots. (See Figure 1)
4. Using a level, mark the wall through both upper mounting
slots. (See Figure 3)
Figure 3
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 16" (406.4mm). Do not
place mounting brackets closer together than 16" (406.4mm).
5. Drill one 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot hole at each
marking.
6. Install an anchor (P) into each pilot hole using a hammer,
making sure that the anchor is flush with the wall.
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (N) in to
pilot holes but do not tighten to wall.
8. Hang mount (CC), aligning upper mounting slots over lag
bolts and adjust side-to-side for proper location.
9. Place one slotted washer (Q) over each flanged lag bolt.
(See Figure 3)
10. Tigh ten lag bolts to secure mount (CC) to wall at upper
mounting slots.
11. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 3)
12. Drill 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot holes at markings
for lower mounting holes. (See Figure 3)
13. Use two 5/16 x 2-1/2" flanged lag bolts (N) and two 5/16"
slotted washers (Q) to attach the mount to the wall through
the lower mounting holes. (See Figure 3)
14. Slide rails to approxi ma te center of screen location.
Locking Rails (Optional)
1. Lock rails into place using two 1/4-20 x 3/4" set screws (T) on
mount upright (CC) and the 1/8" hex key (R). (See Figure 4)
2. Repeat for remaining mount upright.
NOTE: To easily install upper set screw against upper rail,
place set screw (T) onto hex key (R), and feed up into
hole while turning to tighten.
Figure 4
11
5
6
4
12
x 4
(P) x 4
10 710
(N) x 2
(Q) x 2
9
(Q) x 2
13
13
(N) x 2
(MSM1U shown)
(T) x 4
1
(R)
(R)
Installation Instructions MSM1U / MTM1U / LSM1U / LTM1U
9
Attaching Interface Brackets to Screen
1. Align the center of the bracket (Y and Z or AA and BB) with
center of screen. (See Figure 5)
NOTE: The diamond-shape holes in the bracket correspond to
the center of the mount.
Figure 5
WARN ING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2. Select correct screws, nesting spacers (if necessary) and
universal washers (if required) from the hardware bag (A-M)
and attach brackets to back of screen. (See Figure 5)
IMPORTANT ! : The M8 screws do NOT require a
washer . Use the universal washer (MB) only with M4, M5
and M6 screws.
NOTE: The nesting spacers (MA) may be used separately, or
put two together in different configurations to create
different size spacers. (See Figure 6)
Figure 6
Switching Interface Brackets (Optional)
If an installation situation makes adjusting the location of
interface brackets necessary, there are several op tions.
1. The wall brackets may be adjusted side to side at the point
of attachment. (See Figure 7)
2. The location of the left and right interface brackets (Y and Z
or AA and BB) may be switched, with the knobs on the
MTM1U/LTM1U interface brackets (AA and BB) facing the
inside of the mount. (See Figure 7)
Figure 7
Center of bra cke t
Pull cord
[Brackets Y and Z shown]
(MA) (MB)
(A-L)
NOTE: Use universal washer (MB) ONLY with M4, M5
and M6 screws.
(Single) (Nested) (Stacked)
0.375
[9.5]
0.563
[14.3]
0.750
[19.1]
1
2
Knobs
[Brackets AA
and BB shown]
(MTM1U shown)
MSM1U / MTM1U / LSM1U / LTM1U Installation Instructions
10
3. If necessary, the tilt interface bracket knobs may be
switched to allow the interface brackets (AA and BB) to be
reversed. (See Figure 8)
a. Remove display from mount.
b. Remove interface brackets from display.
c. Hold the right interface bracket horizontally, tightly
gripping it so that spacers do not move.
d. Remove the knob and screw.
e. Replace the knob and screw in the opposite order, with
the knob on the inside of the bracket.
f. Switch the right interface bracket to the left side of the
wall mount.
g. Repeat Steps 3c through 3f with the left interface
bracket.
Figure 8
Attaching Screen to Wall Mount
1. Attach wall covers (X) to top and bottom of both wall
brackets. (See Figure 9)
Figure 9
NOTE: NEVER place both interface brackets (Y and Z or AA
and BB) to one side of the wall mount center line! (See
Figure 10)
NOTE: Do NOT allow both interface brackets (Y and Z or AA
and BB) to be located on same side of wall bracket.
(See Figure 10)
Figure 10
3e
Knobs to outside
of brackets
[Brackets AA and BB shown]
3d
(MTM1U shown)
(X) x 4
Both interface brackets must NEVER be located
to one side of the wall brackets!
NEVER place both interface brackets to one
side of the wall mount center line (CL)!
Center Line (CL)
[Brackets Y and Z shown]
(MSM1U shown)
Installation Instructions MSM1U / MTM1U / LSM1U / LTM1U
11
2. Hang screen onto the top rail of the mount (CC). (See
Figure 11)
•MSM1U / LSM1U: Hang top hook of interface
brackets (Y and Z) onto the top rail of the mount (CC).
(See Figure 11)
• MTM1U / LTM1U: Move latch on top of interface
bracket to OPEN position and hang top hook of
interface brackets (AA and BB) onto the top rail of the
mount (CC). (See Figure 11)
NOTE: The screen initia lly installs into the "service mode" to
allow easy cable access.
3. Adjust screen and rails to desired view ing position.
4. Route cables between wall and rails.
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
5. Pull downward on the pull cords and swing inward toward
wall, latching interface brackets to lower rail and fastening
bottom of screen to the mount. (See Figure 11)
6. Attach end of pull cord (a magnet) to mount so it does not
extend beyond bottom of screen. (See Figure 11 )
Figure 11
6
Pull
2
Top
Hook
cords
Latch in
6
Pull
cords
5
5
5
5
2
OPEN
position
(MSM1U shown) (MTM1U shown)
MSM1U / MTM1U / LSM1U / LTM1U Installation Instructions
12
Adjustments
Horizontal Adjustment
1. The mount wall brackets may be adjusted side to side at the
point of attachment. (See F igure 12)
Figure 12
2. The screen may be adjusted along rails side to side.
NOTE: NEVER place both interface brackets (Y and Z or AA
and BB) to one side of the wall mount center line! (See
Figure 10)
NOTE: Do NOT allo w both interface brackets (Y and Z or AA
and BB) to be located on same side of wall bracket.
(See Figure 10)
3. (MTM1U / LTM1U only) Move latch on top of interfa ce
brackets to CLOSED position. (See Figure 14)
Roll/Height Adjustment of Wall Brackets
NOTE: The height adjust wall brackets allow adjustment of
+ 1/2".
1. Turn to right (tighten) to raise side of screen. (See Figure 13)
2. Turn to left (loosen) to lower side of the screen.
Figure 13
Tilt (MTM1U / LTM1U Only)
The interface brackets (AA and BB) allow from -2° to 12° tilt,
and can be locked at 0°, 6° and 12°.
1. Loosen the interface bracket knob.
2. Adjust tilt as required. (See Figure 14)
3. The tilt may be locked at 0°, 6° or 12° using one 1/4-20 x 1"
round head carriage bolt (V) and one 1/4-20 hex nut (W) per
interface bracket. (See Figure 14)
4. Tighten interface bracket knob as necessary.
Figure 14
3" horizontal
1
adjustment possible
Raises screen
Lowers screen
1
2
(S)
(Screen not shown for clarity)
Latch in
CLOSED
position
3
(W)
(V)
2
Lock at 12° tilt
Lock at 6° tilt
Lock at 0° tilt
Interface
bracket
knob
(MTM1U shown)
Installation Instructions MSM1U / MTM1U / LSM1U / LTM1U
13
Locking Screen Interface Brackets (Optional)
1. Lock screen interface brackets onto mount rails using one
3/8-16 x 3/4" set screw (U) on each interface bracket. (See
Figure 15)
Figure 15
Locking Mount (Optional)
1. Add padlock (not included) to interface bracket to complete
security. (See Figure )
NOTE: The padlock maximum shackle diameter is 5/16"
(7.9 mm).
Figure 16
(MTM1U shown)
(MSM1U shown)
1
(U) x 2
1
(U) x 2
1
(MTM1U shown)
Padlock shackle
- 5/16" (7.9mm)
maximum diameter:
1
Padlock shackle
- 5/16" (7.9mm)
maximum diameter:
(MSM1U shown)
MSM1U / MTM1U / LSM1U / LTM1U Installation Instructions
14
Installation Instructions MSM1U / MTM1U / LSM1U / LTM1U
15
MSM1U / MTM1U / LSM1U / LTM1U Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002851 Rev00
2016 Milestone AV Technologies
www.milestone.com
05/16