Chief MTMP1U User Manual
Displayed below is the user manual for MTMP1U by Chief which is a product in the TV Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
FUSION PORTRAIT MEDIUM TILT MOUNT
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MTMP1U
MTMP1U Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all parts are properly
assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system. The wall to which the
mounting system is being attached may have a maximum
drywall thickness of 5/8” (1.6cm) for wood studs.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the MTMP1U does
not exceed
125 lbs (56.7 kg) when mounted to a single 2" x 4" wood stud;
OR
200 lbs (90.7 kg) when mounted to dual 2" x 4" wood studs
or concrete.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mounting system outdoors.
IMPORTANT ! :
The MTMP1U mounts are designed to be
mounted to:
• a bare 8" concrete or 8"x8"x16" concrete block wall, or
• a 2" x 4" wood stud (16" on-center) wall covered by
drywall with maximum thickness of 5/8".
NOTE: The MTMP1U medium tilt mount may be used with the
UL Listed FCAV1U Fusion pull-out accessory.
--SAVE THESE INSTRUCTIONS--
Installation Instructions MTMP1U
3
DIMENSIONS
A
0.53
13.5
0.34
8.7
FOR SINGLE STUD
MOUNTING
DETAIL A
SCALE 2 : 3
DIMENSIONS: INCHES
[MILLIMETERS]
7.00
177.8
RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET
0.34
8.7
1. MAXIMUM MOUNTING PATTERN IS 18.8" (477.5 mm) WITHOUT REVERSING UPRIGHTS
2. MAXIMUM MOUNTING PATTERN IS 22.5" (571.5 mm) WITH REVERSING UPRIGHTS
3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
ENGAGEMENT IS .75" (19 mm)
DIMENSIONS: INCHES
[MILLIMETERS]
MTMP1U Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Installation Instructions MTMP1U
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32" (5.5mm) Wood Stud
#2
3/8" (9.5mm) Concrete
3/16" x 10"
(included)
1/8"
(included)
1/2"
C (4) E (4)
A (4)
M4x12mm B (4)
M4x20mm M4x25mm
D (4)
M5x12mm M5x20mm F (4)
M5x25mm
G (4)
M6x12mm H (4)
M6x20mm
Universal Hardware Kit
I (4)
M6x25mm K (4)
J (4)
M8x12mm M8x20mm L (4)
M8x30mm
MA (8)
[Nesting
MB (4)
[Universal washer]
Wall Mounting Hardware Kit
N (4)
5/16 x 2-1/2"
P (4)
UX10x60mm
Q (4)
[Slotted
washer]
R (1)
1/8"
S (1)
3/16" U (2)
3/8-16 x 3/4"
Mount Hardware Kit
T (4)
1/4-20 x 3/4"
V (2)
1/4-20 x 1"
W (2)
1/4-20
X (1) Y (1)
[left] [right]
[Interface brackets]
Z (1)
spacer]
[Wall mount]
[Included in hardware box]
[Included in hardware box]
[Included in hardware box]
MTMP1U Installation Instructions
6
INSTALLATION
The MTMP1U mounts are designed to be mounted to a bare 8"
concrete or 8"x8"x16" concrete block wall; or 2" x 4" wood studs
(16" on center) wall
covered by drywall of 5/8" maximum
thickness
.
The MTMP1U has brackets which allow the TV to be
tilted.
Locate Mounting Site
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! It is the installers responsibility
to make certain the structure to which the
mounting system
is
being attached is capable of supporting five times the
combined weight of all components located on the mount, not
to exceed 125 lbs (56.7 kg) for mounting to a single 2" x 4"
wood stud; OR 200 lbs (90.7 kg) for mounting to dual 2" x 4"
wood studs or concrete.
NOTE: Proceed to either the Installing to a Wood Stud Wall
section or the Installing to a Concrete Wall section.
Installing to a Wood Stud Wall
1. Determine the center of the TV screen, and where it should
be located on the wall.
WARNING: The MTMP1U is designed to be mounted to
either one or two 2" x 4" wood studs (16" on center).
2. Locate the closest studs to the left and right of the selected
location.
3. Line up the notches on mount (Z) with center of screen
marking to determine vertical center. (See Figure 1)
Figure 1
4. Measure up 8" (203.2mm) from the center point to mark
location of the upper mounting slots. (See Figure 1)
5. Using a level, mark the wall on each stud to attach the
mount through the upper mounting slots. (See Figure 2)
6. Drill one 7/32" (5.5mm) pilot hole in each stud.
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (N) into
pilot holes but do not tighten to wall.
8. Hang mount (Z), aligning upper mounting slots over lag
bolts and adjust side-to-side for proper location.
9. Place one slotted washer (Q) over each flanged lag bolt.
(See Figure 2)
10. Tighten lag bolts to secure mount (Z) to wall at upper
mounting slots.
Figure 2
11. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 10)
12. Drill 7/32" (5.5mm) pilot holes at markings for lower
mounting holes. (See Figure 10)
13. Use two 5/16 x 2-1/2" flanged lag bolts (N) and two 5/16"
slotted washers (Q) to attach the mount to the wall through
the lower mounting holes. (See Figure 10)
14. Slide rails to approximate center of screen location.
15. Proceed to Locking Rails section.
Center of screen
8”
Vertical center
of mount
[203.2mm]
(Z)
4
11 12
56
(Q) x 2
7
10
(N) x 2
(CC)
9
(Q) x 2
13
(N) x 2
13
NOTE: Circled areas indicate mounting holes for
single stud mounting application.
Installation Instructions MTMP1U
7
Installing to a Concrete Wall
1. Determine the center of the TV screen, and where it should
be located on the wall.
2. Line up the notches on mount (Z) with center of screen
marking to determine vertical center. (See Figure 1)
3. Measure up 8" (203.2mm) from the center point to mark
location of the upper mounting slots. (See Figure 1)
4. Using a level, mark the wall through both upper mounting
slots. (See Figure 3)
Figure 3
5. Drill one 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot hole at each
marking.
6. Install an anchor (P) into each pilot hole using a hammer,
making sure that the anchor is flush with the wall.
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (N) into
pilot holes but do not tighten to wall.
8. Hang mount (Z), aligning upper mounting slots over lag
bolts and adjust side-to-side for proper location.
9. Place one slotted washer (Q) over each flanged lag bolt.
(See Figure 3)
10. Mark the attachment points for the lower mounting slots.
(See Figure 3)
11. Drill 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot holes at markings
for lower mounting holes. (See Figure 3)
12. Install an anchor (P) into each pilot hole using a hammer,
making sure that the anchor is flush with the wall.
13. Use two 5/16 x 2-1/2" flanged lag bolts (N) and two 5/16"
slotted washers (Q) to attach the mount to the wall through
the lower mounting holes. (See Figure 3)
14. Tighten all lag bolts to secure mount (Z) to wall.
15. Slide rails to approximate center of screen location.
Locking Rails (Optional)
1. Lock rails into place using four 1/4-20 x 3/4" set screws (T)
on mount (Z) and the 1/8" hex key (R). (See Figure 4)
NOTE: To easily install upper set screw against upper rail,
place set screw (T) onto hex key (R), and feed up into
hole while turning to tighten.
Figure 4
10
5
6
4
11
x 4
(P) x 4
12
7
(N) x 2
(Q) x 4
9
13
13
(N) x 2
(Z)
(T) x 4
1
(T)
(R)
MTMP1U Installation Instructions
8
Attaching Upright Brackets to Display
1. Align the center of the bracket (X and Y) with center of
screen. (See Figure 5)
NOTE: The diamond-shape holes in the bracket correspond to
the center of the mount.
Figure 5
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2. Select correct screws, nesting spacers (if necessary) and
universal washers from the hardware bag (A-M) and attach
brackets to back of screen. (See Figure 5)
IMPORTANT ! : (Dual Stud Installation Only) If M4
fasteners are used to attach brackets to back of screen,
the weight of the screen may NOT exceed 150 lbs
(68.0 kg).
NOTE: The nesting spacers (MA) may be used separately, or
put two together in different configurations to create
different size spacers. (See Figure 6)
Figure 6
Switching Upright Brackets (Optional)
If an installation situation makes adjusting the location of mount
necessary, there are several options.
1. The wall bracket may be adjusted side to side at the points
of attachment (mounting slots). (See Figure 7)
2. The location of the left and right interface brackets may be
switched, with the knobs on the MTMP1U interface brackets
facing the inside of the mount. (See Figure 7)
Figure 7
Center of bracket
(MA)
(MB)
(A-L)
0.375
[9.5]
0.563
[14.3]
0.750
[19.1]
(Single) (Nested) (Stacked)
1
2
Knobs
Mounting
slot
Installation Instructions MTMP1U
9
3. If necessary, the interface bracket knobs may be switched
to allow the brackets to be reversed. (See Figure 8)
a. Remove display from mount.
b. Remove brackets from display.
c. Hold the right interface bracket horizontally, tightly
gripping it so that spacers do not move.
d. Remove the knob, washer and screw.
e. Replace the knob, washer and screw in the opposite
order, with the knob on the inside of the bracket.
f. Switch the right interface bracket to the left side of the
wall mount.
g. Repeat Steps 3c through 3f with the left upright bracket.
Figure 8
Attaching Display to Wall Mount
NOTE: NEVER place both interface brackets (X and Y) to one
side of the wall mount center line! (See Figure 9)
NOTE: Do NOT allow both interface brackets (X and Y) to be
located on same side of wall mount. (See Figure 9)
Figure 9
3e
Knobs to outside
of brackets
3d
Center line (CL)
Both interface brackets must NEVER be located
to one side of the wall mount brackets!
NEVER place both interface brackets to one
side of the wall mount center line (CL)!
MTMP1U Installation Instructions
10
1. Hang screen onto the top rail of the mount (Z).(See Figure 10)
•Move latch on top of interface bracket to OPEN position
and hang top hook of interface brackets (X and Y) onto
the top rail of the mount (Z). (See Figure 10)
NOTE: The screen initially installs into the "service mode" to
allow easy cable access.
Figure 10
2. Adjust screen and rails to desired viewing position.
3. Route cables between wall and rails.
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
4. Pull downward on the pull cords and swing inward toward
wall, latching interface brackets to lower rail and fastening
bottom of screen to the mount. (See Figure 10)
5. Attach end of pull cord (a magnet) to mount so it does not
extend beyond bottom of screen. (See Figure 10)
Adjustments
Horizontal Adjustment
1. The wall mount may be adjusted side to side at the point(s)
of attachment. (See Figure 11)
Figure 11
2. The screen may be adjusted along rails side to side.
NOTE: NEVER place both interface brackets (X and Y) to one
side of the wall mount center line! (See Figure 9)
NOTE: Do NOT allow both interface brackets (X and Y) to be
located on same side of wall mount. (See Figure 9)
3. Move latch on top of interface brackets to CLOSED
position. (See Figure 13)
Roll/Height Adjustment of Wall Mount
NOTE: The height adjust of the wall mount allows adjustment
of + 1/2".
1. Turn to right (tighten) to raise side of screen. (See Figure 12)
2. Turn to left (loosen) to lower side of the screen.
Figure 12
1
4
4
Pull cord
Latch in
OPEN
position
3" horizontal
1
adjustment possible
Raises screen
Lowers screen
1
2
(Screen not shown for clarity)
(S)
Installation Instructions MTMP1U
11
Tilt
The interface brackets (X and Y) allow from -5° to 12° tilt, and
can be locked at 0°, 6° and 12°.
1. Loosen the interface bracket knob.
2. Adjust tilt as required. (See Figure 13)
3. The tilt may be locked at 0°, 6° or 12° using one 1/4-20 x 1"
round head carriage bolt (V) and one 1/4-20 hex nut (W) per
interface bracket. (See Figure 13)
4. Tighten interface bracket knob.
Figure 13
Locking Interface Brackets (Optional)
1. Lock interface brackets onto mount rails using one
3/8-16 x 3/4" set screw (U) on each interface bracket. (See
Figure 14)
Figure 14
Locking Mount (Optional)
1. Add padlock (not included) to interface bracket to complete
security. (See Figure 19)
NOTE: The padlock maximum shackle diameter is 5/16"
(7.9 mm).
Figure 15
Latch in
CLOSED
position
3
(W)
2
Interface
bracket
knob
(V)
Lock at 12° tilt
Lock at 6° tilt
1
4
Lock at 0° tilt
1
(U) x 2
1
Padlock shackle
- 5/16" (7.9mm)
maximum diameter:
MTMP1U Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002655 Rev04
2016 Milestone AV Technologies
www.chiefmfg.com
01/16
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477