Chief NAC25H User Manual
Displayed below is the user manual for NAC25H by Chief which is a product in the Rack Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
6436 City West Parkway, Eden Prairie, MN 55344
• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 / 952.894.6918
8821-0 0201 4 R ev 01
©2012 Mil estone AV Technologies,
a Ducho ssois Group Comp any
04/12
NAC25H E1/G1/S 1 Racks Casters
The NAC25H cas ters are designed for use with Chief® E1, G1 or S1 Series racks . See the spe cific installation i nstructions provided with the
rack for additional installation information.
TOOLS REQUIRED / PARTS INCLUDED
WARNING: FAILURE TO READ, THOROUGHLY UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS CAN RESULT IN SERIOUS
PERSONAL INJURY, DAMAGE TO EQUIPMENT, OR VOIDING OF FACTORY WARRANTY! It is the installer’s responsibility to make
sure all components are properly assembled and installed using the instructions provided.
NOTE: Casters may be installed using a torque wrench, and torque not to exceed 5 ft-lbs.
A (4)
[Casters]
B (16)
1/4-20 D (16)
1/4-20 x 1/2"
C (16)
1/4-20 x 5/8"
7/16"
NOTE: Not all fasteners will be used.
E1/G1 Racks Caster Installation
1. Attach a caster (A) to each lower corner of the E1 rack using four
1/4- 20 x 5/8" Phillips truss hea d machi ne screws (C) [OR four
1/4- 20 x 1/2" hex head cap sc rews (D) ] and four 1/4-20 loc k nuts
(B) for each caster. (See Figure 1)
Figure 1
NOTE: If levelers are already installed in the rac k, leave
levelers installed and adjust them using a 13mm
wrench so they are as close to the floor as possible,
yet still allow movement of the rack on the casters.
S1 Racks Caster Installat ion
1. Attach a caster (A) to each lower corner of the S1 rack using four
1/4-20 x 1/2" hex head cap screws (D) [OR four 1/4-20 x 5/8"
Phillips truss head machine screws (C)] for each caster. (See
Figure 2)
Figure 2
NOTE: If levelers are already installed in the rack, leave
levelers installed and adjust them using a 13mm
wrench so they are as close to the floor as possible,
yet still allow movement of the rack on the casters.
®Chief is a registered trademark of Milestone AV Technologies. All rights reserved.
1
(NE1F2823 rack shown with fasteners B & C)
(A)
(C) x 4
(B) x 4
OR
1
(D) x 4
1
(NS1F1223 rack shown with fasteners D)
(A)
(D) x 4
1
(C) x 4
OR