Chief PAC526FBP6 User Manual
Displayed below is the user manual for PAC526FBP6 by Chief which is a product in the Storage Boxes category. This manual has pages.
Related Manuals
In-Wall Accessory Boxes
I N S T A LLA T I O N I N S T R U C T I O N S
PAC525/526
PAC525 PAC526
Installation Instructions
PAC525/526
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located in the accessory does not exceed
10 lbs (4.5 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: For indoor use only.
IMPORTANT ! : The PAC525/526 mounts are designed to
be mounted to a 2” x 4” wood stud wall 16” on center, a 2” x 4”
-25ga (minimum) steel studs wall, or to a 1/2” minimum
thickness drywall surface.
NOTE: Spacings - Minimum spacings between the 120 Vac
power components and the A/V components shall be main-
tained for safe operation of the equipment when installed in
accordance with the National Electric Code, ANSI/NFPA 70.
NOTE: When selecting a Listed 120 Vac Receptacle for use as
the main power source for the PAC Series boxes (to power the
A/V equipment), make sure that AC Receptacle is rated at least
15A and it is used in the building's AC branch circuit that is
connected to a circuit breaker rated at least 15A. Do not
connect more than 12A from the Receptacle.
In the U.S., the equipment shall be installed per the applicable
requirements of the National Electrical Code, ANSI/NFPA 70.
In Canada, the equipment shall be installed per the applicable
requirements of the Canadian Electrical Code, CSA C22.1.
NOTE: It is the installer’s responsibility to ensure that the
enclosure is bonded to the ground in the switch box, in
accordance with the National Electric Code, ANSI/NFPA 70
or Canadian Electrical Code, CSA C22.1. A green grounding
screw is provided in the enclosure for the purpose, if required.
--SAVE THESE INSTRUCTIONS--
3
DIMENSIONS
P
PAC525
PAC526
10.26
260.7
15.40
391.1
9X .75 X .25
ZIP TIE ANCHOR HOOKS
9.00
228.6
7.00
177.8
4.50
114.3
2.57
65.2
3.88
98.4
3.00
76.2
7.00
177.8
4.50
114.3
2.57
65.2
14.25
362
3.00
76.2
10.93
277.6
2.57
65.2
4.75
120.7
.38
9.5
1.38
34.9
1.13
28.6
3.73
94.9
1.72
[43.7]
1.36
[34.5]
0.87
[21.8]
15.51
394.1
15.40
391.1
14X .75 X .25
ZIP TIE ANCHOR HOOKS
14.25
362
4.75
120.7
3.00
76.2
10.93
277.6
.38
9.5
1.38
34.9
2.57
65.2
14.25
362
5.00
127
11.75
298.5
7.13
181
.82
20.8
1.82
46.2
2.57
65.2
1.13
28.6
3.73
94.9
3.88
98.4
1.72
[43.7]
1.36
[34.5]
0.87
[21.8]
Installation Instructions PAC525/526
4
LEGEND
Installation Instructions
PAC525/526
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Mark level line
Flathead Screwdriver
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Precision hand cut surface
+
5
TOOLS REQUIRED FOR INSTALLATION
PARTS INCLUDED
#2 Phillips
3/16”
1/4”
Stud Sensor
Punch
optional
OPTIONAL PARTS PER CUSTOM CONFIGURATION (NOT INCLUDED)
Conduit Connectors
Conduit Pipe 1/2”, 1” or 1-1/4”
Box Cover
Box Frame Install Box
3” x 2” Steel Old
Work Switch Box
(2” deep)
Raco #420 or equiv.
Electrical
Outlet
Narrow Handy Box
Cover, Duplex
Raco #864 or equiv.
Zip Ties
A
EF
H
G
BC
Template/Temporary Cover
Earthing symbol IEC 60418 No. 5019
affixed adjacent to grounding terminal
Grounding screw installed at factory
D
1 2 3 4 5
#2 Flathead
1/4 - 20 x 2 1/2” Screw
(4x)
#6 - 32 x 3/8” Screw
(8x) #10 - 32 x 3/8”
#6 - 32 Hex Nut
(8x)
3/8” Flat Washer
(4x)
* Items may vary depending on specific model number.
Installation Instructions PAC525/526
Hardware Bag
6
PAC525
PAC5 2 6
INSTALLATION
The PAC525/526 is intended for use both in installations
where an existing finished drywall wall is present, and where
the wall surface has not been finished and the structural studs
are exposed. The wall then must be finished around the
opening of the box after the box has been installed.
PAC525/526 Project Planning
Identify a suitable wall location for the accessory.
Using a stud sensor, locate and mark studs.
Identify possible structural conflicts (electrical wiring,
plumbing, gaslines, HVAC).
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL WIRES OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surfaces is
free of electrical wires and cables before cutting, drilling or
installing fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE
DEATH OR SERIOUS PERSONAL INJURY. ALWAYS
make certain area behind mounting surfaces is free of gas,
water, waste or any other plumbing before cutting, drilling
or installing fasteners.
Determine installation type. Housing is designed to fit
between two adjacent wall studs, or onto a 1/2” minimum
thickness drywall surface.
Plan box and component needs.
Sketch diagrams provided:
1
Drywall attachment only
Pre-sheetrock attachment
Stud & drywall attachment
4
5
Determine all components needed.
Conduit Pipe
Conduit Connectors (large and small)
Electrical Box(es) (3” x 2”)
Steel Electrical Box Cover(s)
Zip Ties
Electrical Outlet(s)
6
2
3
WARNING: All wiring should be performed
by a licensed electrician following all local
codes and ordinances.
Installation Instructions
PAC525/526
7
PAC525/526 Site Preparation
Using a level, draw a horizontal line at lower edge of
install site.
A - STUD ATTACHMENT - create exploratory hole to
confirm edge of stud/studs.
B - DRYWALL ATTACHMENT - mark horizontal cut
locations ensuring a minimum 1/2” distance from
each stud.
7
12
Align on lower edge drawn line (A) and horizontal
marking for inside stud location (B).Use enclosed
template or housing as a template, drawing line
around top and sides of housing.
8
A
A
A
B
B
Cut along outside
edge of line using
utility knife.
Remove drywall.
NOTE:
Cutting past corners
weakens the cleats’
ability to hold securely.
9
PAC525/526 Box Preparation
10 Once wall opening is completed, check stud depth. If 3.5” or greater, proceed to step 11. If less than 3.5” deep, modify depth
of box as follows before proceeding: CAUTION: Injury may occur on sharp edges. Carefully discard the removable tabs.
A - Remove box flange by removing screws.
B - Snap off removable tabs
at perforations provided.
C - Reinstall box flange. Reattach screws.
11
PAC525/526 Box Installation
Feed attached conduit through cut-out and insert box
into opening in wall. Tighten component connections.
13
B B
Installation Instructions PAC525/526
Use four #6 screws (F)
and nuts (G) to assemble
the switch box from either
inside or outside the
PAC525 or PAC526.
Mark the four corners.
CAUTION:
Avoid sharp edges.
Remove knock-outs in box as predetermined in
step 5.
Loosely attach components and conduit (cut to length)
to box to ease fitting into wall opening.
8
Using preferred attachment method (zip ties, bands, etc. -
none included), secure AV components and cables within
the wall box. Attachment methods may use integrated
attachment points at back of wall box or other appropriate
points.
16
Install template as temporary cover if needed to protect
from debris by folding tabs in and inserting into opening.
17
Gather wires and route through cover opening. Install
cover, screw fasteners(2) into place to secure and
complete enclosure.
19
Secure box into
place by methods
chosen.
DRYWALL
ATTACHMENT:
Slide locking
cleats into place.
Tighten screws
to secure.
14
NOTE:
Box may be installed with outer flange removed
for a pre-sheetrock open stud mount configuration.
NOTE:
Save flange for
reattachment after
sheetrock is installed.
Plastic
Spacer
Mounting
Screw
Cover
15
PAC525/526 Final Finishing
Modify enclosure cover before attaching. Break away tab(s)
to allow wire exit from box and meet ventilation needs.
18
NOTE:
Locate front edge of box extended
beyond studs by thickness of
sheetrock to be used.
Installation Instructions
PAC525/526
STUD ATTACHMENT:
Drill pilot holes (optional) into studs through mounting
holes in box. Wood studs - use 3/16” bit. If steel studs
- use 1/4” bit. Install with 1/4 - 20 x 2 1/2” screws (E)
and 3/8” flat washers (H) into pilot holes.
Installation Instructions PAC525/526
9
PAC525/526 Installation Instructions
10
Installation Instructions PAC525/526
11
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002517 Rev02
2015 Milestone AV Technologies
www.chiefmfg.com
04/15
Installation Instructions PAC525/526