Table of Contents
Chief PACL1 User Manual
Displayed below is the user manual for PACL1 by Chief which is a product in the Rack Accessories category. This manual has pages.
Related Manuals
I N S T A L L A T I O N I N S T R U C T I O N S
PACL1
PACL2 (x2)
LeverLock™ Backplane Accessory
PACL1-PACL2
PACL1-PACL2 Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
Chief® is a registered trademark of Legrand AV Inc.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located in the accessory does not exceed 5
lbs (2.3 kg) for the PACL1, 10 lbs (4.5 kg) for the PACL2 or 5
lbs (2.3 kg) for a half PACL2 backplane (after separation.)
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING:
Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: For indoor use only.
--SAVE THESE INSTRUCTIONS--
Installation Instructions PACL1-PACL2
3
DIMENSIONS
PACL1
LATCH LEVER
REMOVABLE STORAGE PANEL
7.08
179.9
5.00
127.0
AA
1.79
45.4
PACL2
PANEL SEPARATION FEATURE
LATCH LEVER
LATCH LEVER
REMOVABLE STORAGE PANEL
12.34
313.3
10.00
254.0
5.00
127.0
A
A
PACL1-PACL2 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS INCLUDED
3/16" (for older PAC boxes ONLY)
#2
#10-24 x 5/8"
C (2)
W (4)
#10-24 x 5/8"
B (2)
[Adapter]
D (2)
#10-24 x 1/4"
A (1)
[PACL1 backplane]
PACL1
C (2)
B (4)
[Adapter]
D (4)
#10-24 x 1/4"
A (1)
[PACL2 backplane]
#10-24 x 5/8"
PACL2
Installation Instructions PACL1-PACL2
5
ASSEMBLY AND INSTALLATION
IMPORTANT ! : If installing to an old PAC box without
the pre-drilled hole locations, it is necessary to drill new
holes into the boxes. Proceed to "Drill Retro-fit Holes"
Section before installing backplanes.
IMPORTANT ! : Backplanes may be installed
horizontally or vertically depending on application. If
installing vertically, make sure the levers are on the
bottom, NOT the top.
Installing Lever Lock™ Backplanes
1. Partially install #10-24 x 1/4" Phillips screws with external
tooth washers (D) into holes on sides of PAC box. (See
Figure 1)
2. Slide each adapter (B) inside PAC box. (See Figure 1)
3. Tighten #10-24 x 1/4" Phillips screws with external tooth
washers (D) to secure adapter (B) to PAC box. (See Figure
1)
Figure 1
4. Slide Lever Lock™ backplanes (A) into adapter (B) slots on
one side of PAC box. (See Figure 2)
Figure 2
5. Slide Lever Lock™ backplanes (A) into adapter (B) slots on
opposite side, making sure they "click" into place. (See
Figure 3)
Figure 3
6. (PACL2 only) If required, break the LeverLock™
backplanes (A) along the scored mid-line. (See Figure 4)
Figure 4
7. Attach components to Lever Lock™ backplanes (B)
following component manufacturer’s instructions. See
templates on pages 9-10 for dimension details.
2
1
(D)
(PACL2 shown)
3
start
tighten
4
4
4
(A)
(B)
(PACL2 shown)
5
Lever Lock™ latch lever
4
4
4
(PACL2 shown)
Mid-line
6
PACL1-PACL2 Installation Instructions
6
Backplane Removal
1. Push down on Lever Lock latch lever on backplane (A).
(See Figure 5)
2. Pull backplane (A) out of adapter hole. (See Figure 5)
3. Remove backplane (A) from PAC box. (See Figure 5)
Figure 5
Drill Retro-fit Holes
1. Refer to Retrofit holes template for PACL1 on page 7 and for
PACL2 on page 8. If desired, these pages may be printed
on 11 x 17 paper to create a paper template to use.
2. Drill 3/16" holes at locations shown on templates. (See
Figure 6) or (See Figure 7)
Figure 6
Figure 7
3. Use #10-24 x 5/8" screws (C) to create threaded holes at
drilled locations. (See Figure 8)
4. Remove #10-24 x 5/8" screws (C) after holes have been
created. (See Figure 8)
Figure 8
5. Proceed to "Installing LeverLock™ backplanes" Section.
latch lever
3
2
1
(PACL2)
(old PAC525)
2
3/16"
(old PAC526)
2
3/16"
3 4
(old PAC526)
4.50
114.4
5.24
133.2
RETROFIT DRILL TEMPLATE
PRINT 1:1 ON 11X17 PAPER
DRILL 3/16" HOLE FOR THREADFORM SCREW
5
PAC525
7
1.37
34.8
4.63
117.5
5.00
127.0
DRILL 3/16" HOLE FOR THREADFORM SCREW
4.50
114.4
5.24
133.2
RETROFIT DRILL TEMPLATE
PRINT 1:1 ON 11X17 PAPER
DRILL 3/16" HOLE FOR THREADFORM SCREW
PAC526
8
13.61
345.8
PANEL TEMPLATE
PRINT 1:1 ON 11X17 PAPER
9
8.36
212.3
P ANEL TEMPLATE
PRINT 1:1 ON 11X17 PAPER
11
10
Installation Instructions PACL1-PACL2
11
PACL1-PACL2 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003179 Rev00
2020 Legrand | AV
www.legrandav.com
06/20