Chief PSMHO2089 User Manual
Displayed below is the user manual for PSMHO2089 by Chief which is a product in the Signage Display Mounts category. This manual has pages.
Related Manuals
I N S T A L L A T I O N I N S T R U C T I O N S
Large Flat Panel Static Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PSMHO2089/2146
PSMHO2089/2146 Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure the mounting system is
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the weight of the screen
does not exceed 400 lbs (181.4 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! :
The PSMH2089/2146 mounts are designed
to be attached to:
•a bare 8" concrete or 8"x8"x16" concrete block wall, or
• a 2" x 4" wood studs wall covered by drywall with
maximum thickness of 5/8". Wood studs may be 16" or
24" on center.
--SAVE THESE INSTRUCTIONS--
Installation Instructions PSMHO2089/2146
3
DIMENSIONS
DIMENSIONS: INCHES
[MILLIMETERS]
44.03
1118.4
27.38
695.3
39.37
1000.0
3.69
93.7
27.38
695.3
34.25
870.0
PSMHO2089
PSMHO2146
PSMHO2089/2146 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions PSMHO2089/2146
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32" - wood
#2
3/8" - concrete
1/2"
A (2)
[Wall plate]
B (2)
[Cross bar with buttons]
C (2)
[Vertical bracket] D (8)
5/16-18
E (4) F (4)
Wall Mounting Hardware
[Installation spacer]
5/16 x 3-1/2"
G (8)
M8 x 16mm
H (1)
M5
PSMHO2089/2146 Installation Instructions
6
ASSEMBLY AND INSTALLATION
Attaching Mount to Wall
1. Using the information included in the Dimensions
drawings and Figure 1, determine where to center and
attach the top wall plate of the PSMHO2089/2146.
Figure 1
2. Wood stud only: Make sure that mounting slots in wall
plate (X) are placed over studs.
3. Mark two mounting locations through the wall plate
mounting slots.
IMPORTANT ! : The minimum spacing between outside
attachment points is 16 inches (40.6cm).The maximum
spacing between outside attachment points is 40 inches
(101.6cm).
4.
Wood stud:
Drill two 7/32" x 2-3/4" pilot holes at marked
locations.
Concrete:
Drill two 3/8" x 3-1/2" pilot holes at
marked locations. (See Figure 2)
5. Concrete only: Install a UX10x60R anchor (not included)
into each pilot hole using a hammer, making sure that the
anchor is flush with the wall.
6. Secure upper wall plate (A) to wall using two 5/16 x 3-1/2"
hex head lag screws (E) and two 5/16" installation spacers
(F). (See Figure 2)
Figure 2
7. Loosely install two vertical brackets (C) to upper wall plate
(A) using four 5/16-18 lock nuts (D). (See Figure 3)
Figure 3
8. Slide wall plate (A) in between wall and lower end of side
brackets (C). (See Figure 4)
9. Loosely install two vertical brackets (C) to lower wall plate
(A) using four 5/16-18 lock nuts (D). (See Figure 4)
Figure 4
16.00
24.00
32.00
40.00
3
4
6
(E) x 3
(F) x 2
5
(not included)
(Concrete only)
(A)
7
(D) x 4
(C) x 2
(X)
8
(A)
9
(D) x 4
(C) x 2
Installation Instructions PSMHO2089/2146
7
10. Level lower wall plate and tighten eight upper and lower lock
nuts (D) in vertical brackets installed in Steps 7 and 9.
11. Mark two mounting locations through the lower wall plate
mounting slots.
12.
Wood stud:
Drill two 7/32" x 2-3/4" pilot holes at marked
locations.
Concrete:
Drill two 3/8" x 3-1/2" pilot holes at
marked locations. (See Figure 5)
13.
Concrete only: Install a UX10x60R anchor (not included)
into each pilot hole using a hammer, making sure that the
anchor is flush with the wall.
14. Secure lower wall plate to wall using two 5/16 x 3-1/2" hex
head lag screws (E) and two installation spacers (F). (See
Figure 5)
Figure 5
Adding Screen to Mount
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SCREEN FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your screen. Properly sized
screws will easily and completely thread into screen
mounting holes.
1. Use eight M8x16mm button head screws (G) to attach two
cross brackets (B) to back of screen. (See Figure 6)
IMPORTANT ! : If using M6 button head screws (E), also
use the shoulder washers (H). (See Figure 6)
Figure 6
2. Move latching flags on mount to the OPEN position. (See
Figure 7)
11
12
14
(E) x 2 (F) x 2
13
(not included)
(Concrete only)
1
(G) x 8
(B) x 2
PSMHO2089/2146 Installation Instructions
8
Figure 7
3. Lift screen following lifting instructions provided by screen
manufacturer.
4. Align mounting buttons on screen with teardrop mounting
holes in mount. (See Figure 8)
Figure 8
5. Move screen forward until recessed area of mounting
buttons is positioned over lower area of teardrop mounting
holes. (See Figure 8)
6. Lower screen until recess area of mounting buttons is
seated in lower area of teardrop mounting holes. (See
Figure 8)
7. Move locking flags to CLOSED position and lock. (See
Figure 7)
8. Route wires and cables to screen.
CLOSED
OPEN
5
6
Screen
5
5
6
6
Installation Instructions PSMHO2089/2146
9
PSMHO2089/2146 Installation Instructions
10
Installation Instructions PSMHO2089/2146
11
PSMHO2089/2146 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003102 Rev00
2019 Legrand | AV
www.legrandav.com
01/19