Chief RMT2 User Manual
Displayed below is the user manual for RMT2 by Chief which is a product in the TV Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
RMT2
RLT2
RXT2
Universal Tilt Mounts
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
RMT2/RLT2/RXT2
RMT2/RLT2/RXT2 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm). Do
not install drywall anchors into the seam between drywall
pieces.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached does not exceed 125 lbs (56.7 kg)
for the RMT2 and RLT2 or 175 lbs (79.4 kg) for the RXT2.
Use with products heavier than the maximum weight
indicated may result in collapse of the mount and its
accessories causing possible injury.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The RMT2/RLT2/RXT2 mounts are
designed
to be mounted to an 8" concrete, 8"x8"x16" concrete block, or
2" x 4" wood studs.
--SAVE THESE INSTRUCTIONS--
Installation Instructions RMT2/RLT2/RXT2
3
DIMENSIONS-RMT2
DIMENSIONS-RLT2
16.50
15.75
MAX
19.94
7.87
TOP MOUNTING
HOLE TO CENTERLINE
NOTCH ON WALL PLATE
7.00
WALL
OPENING
2.50
CENTERLINE
TO BOTTOM OF
WALL PLATE
OPENING
22.00
.34
1.00
8.38
11.00
16.00
5.19
11.49
1.96
- TILTS BACK 5.4°
-CABLE ACCESS
WHEN KICKSTAND
IS ACTIVATED
12°
MAX TILT
16.50
15.75
MAX
28.69
7.87
TOP MOUNTING
HOLE TO CENTERLINE
NOTCH ON WALL PLATE
7.00
WALL
OPENING
30.75
.34
1.00
8.38
15.38
16.00
5.19
24.00
2.50
CENTERLINE
TO BOTTOM OF
WALL PLATE
OPENING
11.49
1.96
- TILTS BACK 5°
-CABLE ACCESS
WHEN KICKSTAND
12°
RMT2/RLT2/RXT2 Installation Instructions
4
DIMENSIONS-RXT2
7.00
WALL
OPENING
38.00
1.00
8.38
.34
19.68
MAX
35.94
19.00
16.00
5.19
24.00
32.00
9.84
TOP MOUNTING
HOLE TO CENTERLINE
NOTCH ON WALL PLATE
11.49
2.50
CENTERLINE
TO BOTTOM OF
WALL PLATE
OPENING
1.96
- TILTS BACK 5°
-CABLE ACCESS
WHEN KICKSTAND
12°
Installation Instructions RMT2/RLT2/RXT2
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
RMT2/RLT2/RXT2 Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32" (5.5mm) #2
1/2" (12.7mm)
5/16" (7.9mm)
GC(6)
M4 x 25mm GG(6)
M5 x25mm GK(6)
M6 x 35mm GN(6)
M8 x 40mm
1/2"(12.7mm)
A(1)
[wall plate]
B(1)
[left upright]
GA(8)
M4 x 16mm
GB(6)
M4 x 20mm
GD(6)
M4 x 35mm
GE(6)
M5 x16mm
GF(6)
M5 x20mm
GI(6)
M6 x16mm
GJ(6)
M6 x 25mm
GL(6)
M8 x 20mm
GM(6)
M8 x 30mm
GO(6)
M8 x 50mm
GP(8)
1/4"(6.4mm)
GQ(8)
GS(8)
[universal washer]
D(4 or 6)
5/16 x 2 1/2"
E(4 or 6)
5/16"
F(4 or 6)
[concrete anchor]
C(1)
[right upright]
For below kit, quantities
are 4 for RMT2 and RLT2,
6 for RXT2.
(RXT2 shown)
GH(6)
M5 x 35mm
G(1)
Hardware Bag
Installation Instructions RMT2/RLT2/RXT2
7
Assembly And Installation
Install Wall Plate to Wall - Wood Studs
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm). Do
not install drywall anchors into the seam between drywall
pieces.
1. Unfold wall plate (A) to prepare it for mounting to wall. (See
Figure 1)
Figure 1
2. Level wall plate (A) and mark locations of pilot holes. (See
Figure 2)
NOTE: The RMT2 must be installed on two 16" studs. The
RLT2 can be installed on 16" studs (inner holes) or 24"
studs (outer holes). For the RXT2, it can be mounted
over two or three 16" studs or two 24" studs. If
mounting to three 16" studs, it must be mounted to all
three studs using the outer holes and center holes.
(See Figure 3) All studs must be 2"x4".
NOTE: The vertical center of the wall plate is labeled as the
center directly below each hinge. Keep this in mind
when determining mounting location. (See Figure 3)
3. Drill 7/32" (5.5mm) diameter pilot holes into wood studs at
marked locations. (See Figure 2)
Figure 2
Figure 3
4. Install 5/16 x 2 1/2" hex head cap screws (D) through four
flat washers (E), wall plate (A) and into wood studs. (See
Figure 4)
Figure 4
1
1
(A)
2
3
x 4 or 6
CENTER
LINE
3 x 16"
2 x 24"
2 x 16"
(D) x 4 or 6
4
(E) x 4 or 6
(A)
RMT2/RLT2/RXT2 Installation Instructions
8
Install Wall Plate to Wall - Concrete or
Concrete Block
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL CORDS OR CABLES
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires and cables before drilling or installing
fasteners.
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH
OR SERIOUS PERSONAL INJURY! ALWAYS make certain
area behind mounting surface is free of gas, water, waste, or
any other plumbing before cutting, drilling, or installing
fasteners.
1. Unfold wall plate (A) to prepare it for mounting to wall. (See
Figure 1)
2. Level wall plate (A) and mark locations of pilot holes at
desired mounting location. (See Figure 5)
IMPORTANT ! : The RMT2-RLT2-RXT2 mounts are
designed to be mounted to an 8" concrete or 8"x8"x16"
concrete block wall.
NOTE: For the RLT2, either the inner or outer four holes may
be used.
NOTE: For the RXT2, use the outer four holes and the two
middle holes on wall plate for installation.
NOTE: The vertical center of the display will be even with the
center line indicated on the labels located directly
below each hinge. Keep this in mind when determining
mounting location. (See Figure 5)
Figure 5
3. Drill 5/16" (8mm) diameter pilot holes into wall at marked
locations. Holes must be drilled at least 3 1/4 inches deep.
(See Figure 5)
4. Install four or six concrete anchors (F) into drilled holes. Use
a hammer to tap anchors into holes. (See Figures 6 and 7)
IMPORTANT ! : The anchors must be installed through
any wall covering until flush with the concrete wall. (See
Figure 6)
Figure 6
5. Using 1/2" (12.7mm) wrench, install screws (D) through flat
washers (E), wall plate (A) and into concrete anchors (F).
(See Figure 7)
Figure 7
CENTER
LINE
2
3
x 4 or 6
Anchor
flush with
concrete
wall
Anchor (F)
wall covering
(A)
Pilot Hole -
5/16 x 3 1/4"
(M8 x 82.5mm)
(D)
(E)
concrete wall
(A)
(E) x 4 or 6
(F) x 4 or 6
5
(D) x 4 or 6
4
Installation Instructions RMT2/RLT2/RXT2
9
Install Brackets to Display
WARNING: The minimum hole pattern size is 100mm x
100mm for the RMT2 and RLT2 and 200mm x 200mm for the
RXT2.
1. Lay display face down on protective surface.
CAUTION: Using screws of improper diameter may
damage your display! Proper screws will easily thread into
display mounting holes.
2. Select screw diameter by examining hardware (GA-GO)
(8mm, 6mm, 5mm, or 4mm) and comparing with mounting
holes on display. (See Figure 8)
3. Select spacers: (See Figure 8)
• If mounting holes are not recessed and both
brackets (B or C) can lay flat against display, then
no spacers are required.
• If mounting holes are recessed, or if protrusions
prevent brackets (B or C) from laying flat, then
spacers (GP or GQ) must be used. Select
shortest spacer which will provide adequate fill.
All spacers must be same length.
CAUTION: Using screws of improper length may damage
your display! Proper screws will have adequate thread
engagement without contacting bottom of display mounting
holes.
IMPORTANT ! : The M8 screws do NOT require a
washer. Use the universal washer (GS) ONLY with M4,
M5 and M6 screws.
4. Select screw length: (See Figure 8)
• Using your hand, insert SHORTEST length screw
of selected diameter (GA, GE, GI or GL) through
bracket (B or C), universal washer (GS, if
required), selected spacer (GP or GQ, if
required), into display mounting hole. Do NOT
thread screw into hole at this time.
• Proper screw length requires base of screw head
to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw
length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
5. Place brackets (B and C) on display, ensuring: (See
Figure 8)
• Upper hooks are towards top of display.
• Center of brackets (B and C) are as close to the
center of the back of display as possible after
being installed. Center of bracket is indicated by
the diamond-shaped hole.
6. If installing display with wide hole pattern, it may be
necessary to swap the uprights (B and C). See Switching
Interface Brackets section for details.
7. Using Phillips screwdriver, carefully install selected screws
through universal washers (GS, if required), brackets (B
and C), and spacers (GP or GQ, if required), into display.
(See Figure 8)
8. Tighten all screws. Ensure all applicable display mounting
holes (4, 6, or 8) are used.
Figure 8
(non-recessed holes)
(recessed holes)
6
(GA-GO) x4,x6,x8
(GS) x4,x6,x8
24
5
7
(GA-GO) x4,x6,x8
24
5
(GS) x4,x6,x8
(GP or GQ)
3
7
(C)
(B)
(C)
6
(B)
NOTE: Use universal washer (GS) ONLY with M4,
M5 and M6 screws.
NOTE: Use universal washer (GS) ONLY with M4,
M5 and M6 screws.
RMT2/RLT2/RXT2 Installation Instructions
10
Install Display to Wall Plate
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached does not exceed 125 lbs (56.7 kg)
for the RMT2 and RLT2 or 175 lbs (79.4 kg) for the RXT2.
Use with products heavier than the maximum weight
indicated may result in collapse of the mount and its
accessories causing possible injury.
WARNING: Display may be very heavy! Ensure display
can be safely lifted and maneuvered as required to install on
wall plate. Failure to take adequate precautions can result in
serious personal injury or damage to equipment!
WARNING: Interface brackets must be hung on opposite
sides of the center tab on wall plate! (See Figure 9)
Figure 9
1. Make sure interface brackets are in the kickstand position by
pulling down on handles as far as possible. (See Figure 10)
2. Hang display with brackets (B and C) on upper rail of wall
plate (A). Kickstand should be engaged with lower portion
of wall plate. (See Figure 10)
Figure 10
NOTE: Any cable management or rear display adjustments
should be made when the display is resting on the
kickstand.
3. Unlock kickstand by pushing up on interface brackets until
kickstand rests against the wall. (See Figure 10)
4. Push up on the interface brackets further in order to lock
display into position against wall. (See Figure 10)
5. Straps can be tucked behind display on notch on interface
brackets (B and C) after installation is complete so that they
will not be visible to the viewer. (See Figure 9)
6. (Optional) Route padlock or cable lock (not included)
through bottom holes on interface bracket to provide
additional security. (See Figure 10)
center tab
of center tab
5
interface
brackets
must be
hung on
opposite sides
4
2
kickstand engaged
1
kickstand
against wall
3
6
(Views from left side)
Installation Instructions RMT2/RLT2/RXT2
11
Switching Interface Brackets (Optional)
For wide hole patterns, interface brackets must be reversed.
See Table below to determine if this is necessary.
1. Remove the tilt tension knob, washer and screw from
interface bracket. (See Figure 11)
IMPORTANT ! : Hold the brackets steady when removing
the knob, washer and screw from interface bracket to
prevent internal washers from falling out. If internal
washers do fall out, they must be reinserted in proper
position before reinstalling knob on the other side!
2. Replace the knob, washer and screw in the opposite order.
(See Figure 11)
Figure 11
3. Repeat for the other interface bracket.
4. Install interface brackets according to instructions in Install
Brackets to Display section.
Tilt Adjustment
1. Adjust tilt tension adjustment knobs to desired tension. (See
Figure 12)
2. Adjust tilt of display by pulling the top of display away from
the wall until desired tilt position is reached. (See Figure 12)
3. Tighten tilt tension adjustment knobs to secure tilt position.
(See Figure 12)
Figure 12
Table 1: Hole Pattern Width
Model # normal installation swap uprights
RMT2 100-440mm 441-506mm
RLT2 100-663mm 664-728.8mm
RXT2 200-847mm 848-913mm
1
2
21 3
tilt tension adjustment
knob
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
RMT2/RLT2/RXT2 Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002428 Rev01
2016 Milestone AV Technologies
www.chiefmfg.com
01/16