Chief RPMB000 User Manual
Displayed below is the user manual for RPMB000 by Chief which is a product in the Projector Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
RPA Elite Series Projector Mounts
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
RPMA/RPMB/RPMC Series
RPMA/RPMB/RPMC Series Installation Instructions
2
NOTE: RPMA, RPMB, and RPMC models are included in
these installation instructions. Throughout these
instructions "RPMX" is used to designate all of the
models covered by these instruct ions.
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provi de for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone A V Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions .
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using th e instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or dama ge to equipment! It is th e
installer’s responsibility to make sure the co mbined weight of
all components attached to the RPMX does not exceed 50 lbs
(22.7 kg).
• The weight capacity of the RPMX may be LIMITED to
the lowest weight capacity of any other mounting
systems/accessories located between the RPMX and
the supporting structure!
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mounting system outdoors.
IMPORTANT ! : The RPMX mounting system is designed to
be:
• mounted to a 1-1/2" NPT or NPSM following ANSI/
ASME B1.20.1 (Schedule 40, 0.154" minimum
thickness aluminum - ASTM B221) threaded extension
column;
• mounted to double 2" x 4" wood stud cross bracing
(1-1/2" on center) between two 2" x 4" ceiling joists with
a maximum drywall covering of 5/8";
• mounted to a concrete ceiling with a minimum
thickness of 8" and a maximum drywall covering of
5/8"; or
• suspended from four #10-24 grade ASTM A307 or
better threaded rods (not included) which are secured
to Unistrut®, angle or channel assembly overhead
structural members (trusses or I-beams) by #10-24
grade ASTM A307 or better jam nuts (not included).
NOTE: RPMA / RPMB / RPMC Series may be used with Listed
Chief models WM110S, WM120S, WM130S,
WM210S, WM220S, WM230S, WM240S, WM210SI,
WM220SI, WM230SI, WM240SI, SL220 and LSB101
(not included).
--SAVE THESE INSTRUCTIONS--
Installation Instructions RPMA/RPMB/RPMC Series
3
DIMENSIONS
TOOLS REQUIRED FOR INSTALLATION
PARTS
2. 79
. 88 5. 40
ROLL ADJUS TMENT
POINT 3
5.50
6.50
1. 50" DI A NP T
4. 50
5. 50
SECURITY LOCK
SECURITY SWITCH
PITCH ADJUSTMENT
POINT 20
YAW ADJUSTMENT
POINT 20
DIMENSIONS: INCHES
1/4" (6.4mm) dia. (concrete)
3/32" (2.4mm) dia. (wood)
5/32" - security
(included)
A (1)
[RPMA/-B/-C]
B (1)
[Example of SLM bracket]
RPMA/RPMB/RPMC Series Installation Instructions
4
LEGEND
Tighten Fastener
Serrez les fixations
Serrare il fissaggio
Befestigungsteil festziehen
Apretar elemento de fijación
Bevestiging vastdraaien
Apertar fixador
Loosen Fastener
Desserrez les fixations
Allentare il fissaggio
Befestigungsteil lösen
Aflojar elemento de fijación
Bevestiging losdraaien
Desapertar fixador
Phillips Screwdriver
Tournevis à pointe cruciforme
Cacciavite a ste l la
Kreuzschlitzschraubendreher
Destornillador Phillips
Kruiskopschroevendraaier
Chave de fendas Phillips
Hex-Head Wrench
Clé à tête hexagonale
Chiave esagonale
Sechskantschlüssel
Llave de cabeza hexagonal
Zeskantsleutel
Chave de cab e ç a se xtavada
Open-Ended Wrench
Clé à fourche
Chiave a punte aperte
Gabelschlüssel
Llave de boca
Steeksleutel
Chave de bo c a s
By Hand
À la main
A mano
Von Hand
A mano
Met de hand
Com a mão
Pencil Mark
Marquage au crayon
Segno a matita
Stiftmarkierung
Marcar con lápiz
Potloodmerkteken
Marcar com lápis
Drill Hole
Percez un trou
Praticare un foro
Bohrloch
Perforar
Gat boren
Fazer furo
Adjust
Ajuster
Regolare
Einstellen
Ajustar
Afstellen
Ajustar
Hammer
Martillo
Hammer
Martelo
Martello
Hamer
Marteau
Target of Projector
Punto de enfoque del proyector
Ziel des Projektors
Mira do projector
Punto di proiezione
Doel van de projector
Cible du projecteur
Security Wrench
Clé de sécurité
Chiave di sicurezza
Sicherheitsschlüssel
Llave de seguridad
Veiligheidssleutel
Chave de segurança
Installation Instructions RPMA/RPMB/RPMC Series
5
PREPARATION
Locate Mounting Site
WARNING: IMPROPER INSTALLATION MAY LEAD TO
PROJECTOR MOUNT FALLING CAUSING SEVERE
PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is
the installers responsibility to make certain the structure to
which the p rojector moun t is being mounte d is capable of
supporting five times the weight of the projector mount and all
attached equipment. Reinforce the structure as required
before installing the projector mount.
1. Determine required position of the RPMX projector mount.
2. Determine required distance of the projector mount from the
screen using the projector specifications.
NOTE: Proceed to In stalling to 1-1/2" Threaded Extension
Column, Installing to Wood Framework, Installing
to Concrete Ceiling, or Installing to Threaded Rod
section, as appropriate.
INSTALLATION
Installing to 1-1/2" Threaded Extension Column
1. Install 1-1/2" NPT or NPSM following ANSI/ASME B1.20.1
(Schedule 40, 0.154" minimum thickness steel or aluminum
- ASTM B221) threaded extension column (not included)
into threaded collar until tight, with a minimum of four
threads engaged.
2. Thread RPMX projector mount (A) onto the threaded
extension column (not included) until hand tight.
3. Turn RPMX clockwise or counter-clockwise until front of
mount is facing target.
IMPORTANT ! : When RPMX is properly positioned, the
set screw access hole should be pointing directly at
target, or 180° AWAY from target.
4. Secure RPMX to pipe by turning set screw with a 5/32" hex
key until tight. (See Figure 1)
CAUTION: DO NO T OVERTIGHTEN! Over tightening of
set screw can damage threads on pipe.
Figure 1
5. Turn security screw (access from bottom of RPMX) (See
Figure 2) using a Phillips screwdriver until set screw cannot
be seen through set screw access hole in RPMX. (See
Figure 1)
Figure 2
6. Proceed to Installing Projector with Interface Bracket
section.
2
4
(A)
Set screw
access hole
x 1
Threaded
extension
column
(not included)
(not included)
(RPMX bottom view)
5
x 1
Security screw
RPMA/RPMB/RPMC Series Installation Instructions
6
Installing to Wood Framework (Joists)
1. Using th e R P MX as a gu i d e, mark four mountin g hole
locations. (See Figure 3)
2. Drill four 3/32" (2.4mm) dia. pilot holes to a depth of 1-3/4"
(45mm) deep.
Figure 3
3. Align four mounting holes in RPMX with four pilot holes.
IMPORTANT ! : When RPMX is properly positioned, the
set screw access hole should be pointing directly at
target, or 180° AWAY from target.
4. Secure RPMX to structure using four #10-24 x 3" Grade 2
wood screws (not included) and four 1/4" Grade 2 flat
washers (not included). (See Figure 4)
Figure 4
5. Proceed to Installing Projector with Interface Bracket
section.
Installing to Concrete Ceiling
WARNING: The RPMX is designed to be mounted to a
concrete ceiling with a minimum thickness of 8" and a
maximum drywall covering of 5/8".
1. Using the RPMX as a guide, mark four mounting hole
locations on ceiling using a pencil or similar tool.
2. Drill four 1/4" (6.4mm) dia. pilot holes to a depth of 2-1/2"
(64mm) deep. (See Figure 5)
Figure 5
Ø 2.4mm
(Ø 3/32”)
45mm
(1-3/4”)
x 4
1
2
Pilot
hole
dimensions
4
3
x 4
2
x 4
1
Ø 6.4mm
(Ø 1/4”)
64mm
(2-1/2”)
Pilot
hole
dimensions
Installation Instructions RPMA/RPMB/RPMC Series
7
3. Align four mounting holes in RPMX with four pilot holes.
IMPORTANT ! : When RPMX is properly positioned, the
set screw access hole should be pointing directly at
target, or 180° AWAY from target.
WARNING: Anchors (not provided) must be installed into
structurally sound solid concrete. Installation into hollow
concrete block, mortar, or concrete that exhibits cracking,
spalling, or other defects may result in failure of anchor and
serious personal injury or damage to equipment.
4. Install four Toggler AF6 Alligator concrete anchors (not
included) by inserting into pilot holes and hammering in until
flush with mounting surface.
5.
Secure RPMX to stru cture using four 1/4" Grad e 2 fl at
washers and four #10-24" x 3" Grade 2 wood screws (not
included). (See Figure 6)
Figure 6
Installing to Threaded Rod
NOTE: The RPMX projector mount may be suspended from
four #10-24 grade ASTM A307 or better threaded rods
(not included) which are secured to unistrut, angle or
channel assembly overhead structural members
(trusses or I-beams) by #10-24 grade ASTM A307 or
better jam nuts (not included).
1. Secure one end of each of the four threaded rods (not
included) to the structural member.
2. Install four #10-24 jam nuts (not included) onto each
threaded rod.
3. Install RPMX onto threaded rods, inserting the rods into the
four holes on top of the RPMX.
NOTE: Hole in the RPMX allows socket wrench access without
unit disassembly.
4. Secure the threaded rods to the RPMX with #10-24 jam nuts
(not included) and 1/4" washers (not included ). (See
Figure 7)
Figure 7
5. Proceed to Installing Projector with Interface Bracket
section.
PROJECTOR INSTALLATION
IMPORTANT ! : Model RPMX uses optional Chief "SLM"
Series interface brackets. See Parts drawing.
1. Attach projector to interface bracket (B) using installation
instructions and hardware included with the interface
bracket.
NOTE: Security screws can be substituted when mounting
Interface bracket to projector by using the hardware
and installation instructions in the All-Points Security
Kit (included with interface bracket).
Installing Projector with Interface Bracket
1. Orient projector with interface bracket.
2. Lift projector so that screws with thumb nuts are aligned with
mounting slots in mount base. (See Figure 8)
3. Slide projector with mounting bracket into mounting slots in
mount base until screws are seated against the back of
mounting slots.
4
x 4
5
x 4
3
1
Secure using
3
4
Secure with jam
nuts and washers
(not included)
Threaded
rods
(A)
jam nuts
(not included)
RPMA/RPMB/RPMC Series Installation Instructions
8
WARNING: IMPROPER INSTALLATION CAN LEAD TO
PROJECTOR FALLING RESULTING IN SERIOUS
PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Make
certain mounting slots in projector mount base slide under
thumb screws and that screws are seated in the back of slots.
Figure 8
4. Verify mounting screws are properly seated in mounting
slots in projector mount base.
5. Move locking lever to "LOCKED" position. (See Figure 8)
6. Insert key into lock and turn to secure projector to RPMX.
7. Route all cables, as required.
ADJUSTMENTS
The RPMX projector mount can be adjusted for pitch (vertical
elevation), roll (horizontal tilt), and yaw (rotation).
WARNING: OVER-LOOSENING OR REMOVAL OF
HARDWARE MAY RESULT IN PERSONAL INJURY OR
SERIOUS DAMAGE TO EQUIPMENT! RPMX projector
mount and hardware is to be loosened only enough to allow
for necessary movement.
YAW Adjustment (Rotation)
1. Loosen YAW adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 9)
2. Turn YAW micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
3. Tighten YAW adjustment locking screw using a #2 Phillips
screwdriver.
Figure 9
Pitch Adjustment (Vertical Elevation)
1. Loosen PITCH adjustment locking screw using a #2 Phillips
screwdriver. (See Fig ure 10)
2. T urn PITCH mic ro-adjustment screw right or lef t using a #2
Phillips screwdriver until image is properly aligned on target.
3. Tighten PITCH adjustment locking screw using a #2 Phillips
screwdriver.
Figure 10
2
3
(Mounting structure not shown for clarity)
(A)
[Locked]
[Unlocked]
Locking
lever
5
Lock
Mounting
slots
6
1
2
3
2
1
2
3
2
Installation Instructions RPMA/RPMB/RPMC Series
9
Roll Adjustment (Horizontal Tilt)
1. Loosen ROLL adjustment locking screw using a #2 Phillips
screwdriver. (See Figure 11)
2. Turn ROLL micro-adjustment screw right or left using a #2
Phillips screwdriver until image is properly aligned on target.
3. T ighten ROLL adjustment locking screw using a #2 Phillips
screwdriver.
Figure 11
1
2
3
2
RPMA/RPMB/RPMC Series Installation Instructions
10
Installation Instructions RPMA/RPMB/RPMC Series
11
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
RPMA/RPMB/RPMC Series Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002642 Rev01
2016 Milestone AV Technologies
www.milestone.com
03/16