Chief RPMB324 User Manual
Displayed below is the user manual for RPMB324 by Chief which is a product in the Projector Mounts category. This manual has pages.
Related Manuals
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Mile-
stone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the instal-
lation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty,
expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this
document.
Chief, a products division of Milestone AV Technologies
6436 City West Parkway, Eden Prairie, MN 55344
• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 / 952.894.6918
8800-002799 Rev00
©2015 Milestone AV Technologies
www.chiefmfg.com
10/15
INSTALLATION INSTRUCTIONS
SLB-324 and SLM-324 Interface Brackets
SLB-324 and SLM-324 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific installation instructions
provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
**Only used when installing SLB interface brackets.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB interface bracket. If an SLM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place spacers over threaded inserts in bottom of the projector, according to the required mounting pattern.
4. Place the interface bracket onto the spacers, aligning the mounting holes in the bracket with the spacers and threaded inserts in the bottom
of the projector and ensuring that triangle in bracket points towards front of projector.
5. Position M6 x 30mm pan head screws with M6 flat washers, and/or flat head mounting screws WITHOUT washers, into the bracket
mounting holes, through spacers, and into threaded inserts.
6. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (6) Screw, Phillips Pan Head, Machine, M6 x 30mm
(6) 10-24 Thumb Nuts** (2) Screw, Phillips Flat Head, Machine, M6 x 30mm
(1) All-Points Security Kit (6) Washer, M6
(1) 5/32" Security Hex Key (6) Spacer, .680 x .390 x .625"
Towards front
of projector
SLM-324
Mounting Patterns
(Dependent on projector model)
1. Six mounting holes 2. Four mounting holes
(includes 2 flat head
3. Four mounting holes (Pattern
2) PLUS one corner
mounting hole (includes 2
flat head screws.
F*
F* F*
F*
Towards front
of projector
Towards front
of projector
screws)
SLB-324 SLM-324
F* indicates use flat head screw