Chief SLB222 User Manual
Displayed below is the user manual for SLB222 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0005 7 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
SSB-222, SSM-222, SLB-222 and SLM-222 Interface Brackets
SSB-222, SSM-222, SLB-222 and SLM-222 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit conten ts. If any listed parts are missing, immediately contact a Ch ief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. Place the interface bracket onto the bottom of the projector.
4. Align the four mounting holes in the interface bracket with the four threaded inserts in the bottom of the projector.
5. Using the four M4 – 12mm mounting screws and M4 flat washers, secure interface bracket t o projector and tighten all fasteners at this time.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) M4 – 12mm Screws
(5) 10 - 24 Thumb Nuts** (4) M4 Flat washers
(1) All-Po ints Secu rity Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encirc led locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
Towards front of
projector
Towards front of
projector
SLB-222 SLM-222
(Note: SS
M-styleinterfac
e bracke
t conne
ction
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: S
SB-styl
e interfa
ce brac
ket con
nections
a
r
e
e
n
c
i
r
c
l
e
d
)