Chief SLB280 User Manual
Displayed below is the user manual for SLB280 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0208 7 R ev 01
©2011 Milestone AV Technologies,
a Duchossois Group Company
12/11
**Only used when installing SLB/SSB interface br ackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations
above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket
SSB-280, SSM-280, SLB-280 and SLM-280 Interface Brackets
SSB-280, SSM-280, SLB-280 and SLM-280 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack c arton and verify kit contents. If any listed parts are missing, immediately contac t a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. D O NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place spacers onto the bottom of the projector, aligning the spacers with the threaded inserts in the projector.
4. Place the i nterface bracket ont o the spacer s, alignin g the mounting holes in the bracket wi th the spacers and thre aded inserts i n the bo ttom
of the projector and ensuring that triangle in bracket points towards front of projector.
5. Position M4 x 25mm mounting screws (OR four M5 x 25mm mounting screws) with four M4 (OR four M5) flat washers into the bracket
mounting holes and threaded inserts. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security s cr ews can b e subs titu ted wh en mounti ng In terfa ce bracke t to proje ctor by u sin g the part s an d insta llat ion in struct ions i n the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) Screw, Phillips Pan Head, Machine, M4 x 25mm*
(4) 10-24 Thumb Nuts ** (4) Screw, Phillips Pan Head, Machine, M5 x 25mm*
(1) All-Points Security Kit (4) Washer, M4*
(1) 5/32" Security Hex Key (4) Washer, M5*
(4) Spacer, .500 x .316 x .500 * Ver ify correct size screw and washer needed to install bracket.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.
SLB-280 SLM-280
Towards front
of projector Tow ards front
of projector