Chief SLB3131 User Manual
Displayed below is the user manual for SLB3131 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0202 0 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
SSB-3131, SSM-3131, SLB-3131 and SLM-3131 Interface Brackets
SSB-3131, SSM-3131, SLB-3131 and SLM-3131 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the
specific installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit conten ts. If any listed parts are missing, immediately contact a Ch ief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. Locat e t he two -rear rubber pa ds as s een in Fi gur e 1. Cu t the smal l tab on each r ear pad s o they can p ush do wn in to the mounti ng slot s.
Figure 1:
(1) Interface Bracket (1) Locking Tab
(4) 10 - 24 Thumb Nuts** (1) # 8 - 32 x 1/2” Phillips Pan Screw
(1) All-Po ints Secu rity Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encirc led locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
Towards front of
projector
Toward s fr o nt of
projector
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0202 0 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
4. Locat e t he front adjust able fo ot as seen in Fi gure 2. Cut th e two sma ll ta bs on the f ront cen ter mo unting slot so it can pus h down i nto the
mou nting slot.
Figure 2:
5. A lign t he interface bracket’s two rear and one front tabs with the t wo r ear and one front mo unting slots i n the projector. Insert t he bracket
tabs down into the mounting slot and slide the bracket back toward the rear of the projector as seen in Figure 3.
Figure 3:
6. Locate the pre-packaged interface bracket locking tab. Place the locking tab through the front opening in the mounting bracket and lay
it on its side as seen in Figure 4.
Figure 4:
7. Us ing a sc rewdriver, sl ide the locking t ab to t he lef t and pu sh t he end of the lo cking t ab int o the moun ting s lot i n fron t of t he fro nt mou nting
tab on the bracket as seen in Figure 5.
Figure 5:
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0202 0 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
8. Using a screwdriver, align the hole in the locking tab with the threaded hole on the interface bracket in the front mounting tab as seen in
Figure 6.
Figure 6:
9. Locate the pre-packaged #8 - 32 x 3/8” locking tab screw. Place the # 8 screw through the hole in the locking tab and secure interface
bracket to projector as seen in Figure 7. Tighten all fasteners at this time.
Figure 7:
NOTE: Securit y screws can be subst ituted whe n mountin g interface brac ket to proje ctor by usi ng the par ts and i nstall ation instruct ions in t he
All-Points S ecurit y Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.