Chief SLM213 User Manual
Displayed below is the user manual for SLM213 by Chief which is a product in the Projector Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0027 8 R ev 01
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
SSB-213, SSM-213, SLB-213 and SLM-213 Interface Brackets
SSB-213, SSM-213, SLB-213 and SLM-213 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT overtighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Push four rubber bumpers into four holes on the large and small brackets (from top down) so that projector can sit on bumpers.
4. Slide large bracket around projector so projector front foot is behind front bracket tab.
5. Slide smaller bracket around projector and over large bracket. Install two 10-24 x 1/4" screws and fasten loosely.
6. Slide two brackets together firmly against the projector sides. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Se curity sc rews c an be substit ute d when mount ing in terface br acke t to projec tor by usi ng the par ts and i nstallat i on inst ructions i n the
All-Poi nts Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(2) Interface Brackets; 1 large, 1 small (4) Bumper, Rubber
(4) 10-24 Thumb Nuts ** (2) Screw, Pan head, 10-24 x 1/4"
(1) All-Points Security Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Sp ecific to SSB-style and SSM-style interface br acket instal lation, all appropriat e screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-
style interface bracket installation.
SLB-213 SLM-213
Towards fr ont of
projector
Towards front of
projector
Front Brac ket
Tab
Front Bracket
Tab
Rubb er B umpers ( loca ted in br acke t co rners - fo ur lo catio ns)
(No
te: SSB
-styleinterfa
ce brac
ket co
nnectio
ns
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: S
SM-sty
le inte
rface b
racketconnec
tions
are encirc
led)