Chief SLM2220 User Manual
Displayed below is the user manual for SLM2220 by Chief which is a product in the Projector Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated corpo rat ions and subsidiaries (collectiv el y, "Miles tone"), intend to mak e th is ma nual accurate an d compl ete. However, Mi lestone mak es
no claim that the information con tained herein co vers all deta ils, con ditions or variations, nor does it provide for every possible conti ngency in connection with the i nstallation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty , expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility fo r accuracy, completeness or suffici ency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850- 000148 RevB
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets
SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information. Unpack carton and verify kit contents. If any listed parts are
missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the encircled
locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket
installation.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. Plac e in terf ace br a cke t onto bott om of proj ecto r wi th thre e t hrea ded ins erts fa ce up and two t owar ds f ron t of pr ojec tor. Sec ure int erfa ce br ac ket to
projector using selected screw for model of projector (countersink screw or pan head screw).
4. Countersink screw in center countersink hole and pan head mounting screw in flush mounting hole. Your projector may require one or three
s pacers for aligning bracket flat to projector. (Some models may suspend over bottom and have space between bracket and projector.)
Hitachi CP-X270W
1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .190 x 1/2" and 1/2" x .190 x 3/8" on top of each other and
c entered over right th readed insert in fron t of project or. Using two 1/2" x .218 x 1/4" ,1/ 2" x .218 x 1/ 4" and 1/2" x .258 x 3/16" spacers, stack and
place them over three threaded inserts on left.
2. Place interface bracket onto projector and align spacers and mounting holes.
3. Position a nd align interface bracket t o projector using M4 x 30 mm c ountersink screw in middle of br acket, M4 x 30mm Phil li ps pan head screw in
r ight of brack et, and M4 x 16m m Phi llips pan head scr ew i n left of b rack et. Tigh ten all fa steners at this ti me, securing the bracke t to t h e projector.
Hitachi CP-S307W, CP-X380W, CP-X385W
1. Place projec tor ups ide dow n on tabl e w ith proj ector lens faci ng a way. Sta ck 1/2" x .218 x 1/4 " and 1/2 " x .2 58 x 3 /16" sp ace rs o n t op of each oth er
c ente red ov er righ t th rea ded ins ert in front of p roje ctor. U sing tw o 1 /2" x .25 8 x 3/ 16" sp ace rs, plac e one ov er midd le thre ade d i nser t and one ov er
left threaded insert of projector.
2. Place interface bracket onto projector and align spacers and mounting holes.
3. Position a nd align interface bracket t o projector using M4 x 16 mm c ountersink screw in middle of br acket, M4 x 20mm Phil li ps pan head screw in
r ight hole of br acket and M 4 x 16mm Phil lips pan head screw in l eft hole of brac ket. Tighten all fasteners at this time, s ecuring th e brac ket to the
projector.
NOTE: Securi ty Sc rew s can be sub sti tu ted whe n mo unting interface bracket to projec tor b y us ing the parts and ins tal lation instructi ons in
the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) In ter fac e B rack et (3) 1/2" x .218" x 1/4" Round Spacer **** (1) Screw, Philli ps Flat Head,
Machine, M4 x 16mm **** (1) Screw, Phillips Pan Head,
Machine, M4 x 30mm ****
(4) 10 - 24 Thumb
Nuts** (3) 1/2" x .194 " x 1/2" Round S pacer **** (1) Screw, Phillips Pan H ead,
Machine, M4 x 16mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
(1) All-Points Security
Kit (3) 1/2" x .194" x 3/8" N ylon Spacer **** (1 ) Scre w, Phi llip s Fl at Head M achi ne,
M4 x 25mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
(2) Washer, Flat, M4 (1) Screw, Phillips Pan Head, Machine,
M4 x 8mm **** (1) Screw, Phillips Pan H ead,
Machine, M4 x 20mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
SLB-2220 SLM-2220
Towards front of
projector
Towards front of
projector
(
Note: SSB-style interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: SSM-style interface bracket connection
s
a
re encircled)