Chief SLM257 User Manual
Displayed below is the user manual for SLM257 by Chief which is a product in the Projector Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0204 7 R ev 00
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
12/09
SSB-257, SSM-257, SLB-257 and SLM-257 Interface Brackets
SSB-257, SSM-257, SLB-257 and SLM-257 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack c arton and verify kit contents. If any listed parts are missing, immediately contac t a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
**Only used when installing SLB/SSB interface brackets.
NOTE: Sp ecific to SSB-style and SSM-style interface bracket installation: All appropriate screws co me pre-installed in the ci rcled locations.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. D O NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place interface bracket onto bottom of projector, ali gning the mounting holes in bracket with threaded inserts in bottom of projector, and
ensuring that triangle in bracket points towards front of pr ojector.
4. Position four M6 x 10mm pan head mounting screws with four M6 flat washers through the mounting holes in bracket into the threaded
inserts. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security s cr ews can b e subs titu ted wh en mounti ng In terfa ce bracke t to proje ctor by u sin g the part s an d insta llat ion in struct ions i n the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) Screw, Phillips Pan Head, Machine, M6 x 10mm
(6) 10-24 Thumb Nuts ** (4) Washer, M6
(1) All-Points Security Kit (1) 5/32" Security Hex Key
Towards front
of projector Towa rds front
of projector
SLB-257 SLM-257