Chief SLM273 User Manual
Displayed below is the user manual for SLM273 by Chief which is a product in the Projector Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0207 0 R ev 00
©2010 Milestone AV Te chnologies,
a Duchossois Group Company
10/10
SSB-273, SSM-273, SLB-273 and SLM-273 Interface Brackets
SSB-273, SSM-273, SLB-273 and SLM-273 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack c arton and verify kit contents. If any listed parts are missing, immediately contac t a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. D O NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place two spac ers on to th e bo ttom o f the pr oj ect or, aligning with t wo moun ting hol es in t he ma in bod y o f bra cket a nd the t hrea de d inserts
in the bottom of the projector and ensuring that triangle in bracket points towards front of projector.
4. Position two M4 x 25mm mounting screws with M4 fl at washers t hrough the spa cers a nd into the thr eaded inserts . Place three M4 x 12mm
screws with M4 fl at washers into the threaded inserts and mounting holes on interface bracket tabs. Tighten all fasteners at this time,
securing the bracket to the projector.
NOTE: Securi ty screws c an be subs titute d when mo unting Int erface b racket t o proje ctor by usi ng the par ts a nd insta llatio n instruct ions
in the All-Point s Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket ( 3) Scre w, Philli ps Pan Hea d, Ma chin e, M4 x 12mm
(4) 10-24 Thumb Nuts ** (2) Screw, Phillips Flat Head, Machine, M4 x 25mm
(1) All-Points Security Kit (2) Spacer, .500 x .316 x .500
(1) 5/32" Security Hex Key (5) Was her, Fl at, M4
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.
SLB-273 SLM-273
Towards front
of projector Towards front
of proj ector