Chief SLM286 User Manual
Displayed below is the user manual for SLM286 by Chief which is a product in the Projector Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0209 2 R ev 00
©2011 Milestone AV Technologies,
a Duchossois Group Company
05/11
SSB-286, SSM-286, SLB-286 and SLM-286 Interface Brackets
SSB-286, SSM-286, SLB-286 and SLM-286 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack c arton and verify kit contents. If any listed parts are missing, immediately contac t a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. D O NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place spacers over threaded inserts on bottom of project or.
4. Place the i nterface bracket ont o the spacer s, alignin g the mounting holes in the bracket wi th the spacers and thre aded inserts i n the bo ttom
of the projector, and ensuring that triangle in bracket points towards front of projector.
5. Position M4 x 25mm mount ing screws into the bracket, spa cers and threaded inserts. Tight en all fasteners at this time, secu ring the bracket
to the projector.
NOTE: Security s cr ews can b e subs titu ted wh en mounti ng In terfa ce bracke t to proje ctor by u sin g the part s an d insta llat ion in struct ions i n the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket ( 4) Scre w, Philli ps Pan Hea d, Ma chin e, M4 x 25mm
(4) 10-24 Thumb Nuts ** (4) Spacer, .500 x .316 x .500
(1) All-Points Security Kit (1) 5/32" Security Hex Key
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface br acket connections are circled.
SLB-286 SLM-286
Towards front
of projector Towards front
of proj ector