Chief SSB007 User Manual
Displayed below is the user manual for SSB007 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0007 4 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
SSB-007, SSM-007, SLB-007 and SLM-007 Interface Brackets
SSB-007, SSM-007, SLB-007 and SLM-007 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
**Only used when installing SLB/SSB interface bracket.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the encircled
locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket
installation.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PAR TS AND CAN L EAD TO SE RIOUS PE RSONAL I NJUR Y AND DAMAG E
TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. R emove the re ar blac k h ard pla sti c foo t fro m the pro jector using a sm all flat scr ew driver and pry it up from th e p roje ctor ho usin g. This foo t is he ld
on by two-face tape.
4. Remove the screw under the black plastic foot.
5. Remove the rear adjustable foot from the projector.
6. Remove the two small screws in the front of the bottom of the projector housing.
7. Place the four 3/8” nylon spacers over the four threaded inserts in the bottom of the projector over each screw hole previously removed.
8. P lac e th e in terface bra cket on to th e f our ½” nylo n s pace rs on t he bott o m of t he p rojector and al ign the four mo unting hole s in the bra cke t w ith t he
f our nylon spacers.
9. Place the M4 x 20mm screw and flat washer into the rear adjustable foot hole location. Place the remaining three M3 x 16mm screws, and flat
washers into the remaining holes. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions
in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) M3 Flat washer
(5) 10 - 24 Thumb Nuts** (1) M4 -20mm Screws
(4) ½” x .190” x 3/8” Nylon Spacers (1) M4 Flat washer
(3) M3 -16mm Screws (1) All-Points Security Kit
Towards front of
projector
Towards front of
projector
(Note: SSB-style interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: SSM-sty le in terfacebracket connections
are encircled)
SLB-007 SLM-007