Chief SSB029 User Manual
Displayed below is the user manual for SSB029 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802 -000115 R ev 01
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
SSB-029, SSM-029, SLB-029 and SLM-029 Interface Brackets
SSB-029, SSM-029, SLB-029 and SLM-029 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing hanger bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws ont o the 10-24 x 5/8" Phillips pan head screws. DO NOT fully ti ghten thumb screws at this time.
2. Turn projector upside down.
3. Place 1/2" spacers over center-threaded hole in bottom of projector.
4. Place interface bracket onto projector bottom and align center hole in bracket with spacer and the mounting holes in bracket with the
threaded inserts in projector.
5. Position M4 x 20mm Phillips flat head screw into center-mounting hole (leave loose at this time).
6. Se cure interface bracket to projector by using the M4 x 8mm Phillips pan head screws with flat washer. Tighten all fastener s at this time,
securing the bracket to the projector
7. Tighten the M4 x 20mm Phillips flat head screw.
NOTE: Security screws can be substitute d when mounting hang er bracket to project or by using the pa rts and installation instr uctions
in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (1) Screw, Phillips Flat Head, Machine, M4 x 20mm ****
(1) All-Poi nts Secu rity Kit (2) Screw, Phillips Pan Head, Machine, M4 x 8mm ****
( 6) 10- 24 Thumb Nu ts * * (1) 1/2" x .194" x 1/2" Round Spacer ****
(2) Wa sher, Flat, M 4
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encirc led locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
SLB-029 SLM-029
(Note: SSM-style interface brac
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
No te: SSB-styl e interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)
Toward s fro nt of
projector
Towards front of
projector