Chief SSB1065 User Manual
Displayed below is the user manual for SSB1065 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0201 8 R ev 01
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
SSB-1065, SSM-1065, SLB-1065 and SLM-1065 Interface Brackets
SSB-1065, SSM-1065, SLB-1065 and SLM-1065 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the
specific instal lation instructions pr ovided with the mount for add itional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws ont o the 10-24 x 5/8" Phillips pan head screws. DO NOT fully ti ghten thumb screws at this time.
2. Turn projector upside down.
3. Place 1/4" spacers over the threaded inserts in bottom of projector.
4. Place interface bracket onto bottom of projector and align spacers with mounting holes.
5. Using the M4 x 16mm Philli ps pan head screws a nd flat washers, secure interface bracket to projector and tig hten all fasteners at this tim e.
NOTE: Sec urity Scr ews c an be subst ituted wh en mount ing i nterface brac ket to projec tor by using t he parts and in stallat io n inst ructions in the
All-Poi nts Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) Screw, Phillips Pan Head, Machine, M4 x16mm ****
(4) 10 - 24 Thumb Nuts ** (4) Was her, Fl at, M4
(1) All-Points Security Kit (4) 1/2" x .218" x 1/4" Round Spacer ****
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
enci rc led loc ations a bove. DO NOT at tempt to s ubst itut e and USE O NLY thi s pre- ins talled hardwar e for SSB-s tyle an d S SM-styl e
interface bracket installation.
SLB-1065 SLM-1065
Towards front of
projector
Towards front of
projector
(Note: SSM-style interface bracket connection
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
Note: SSB-style interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)