Chief SSB169 User Manual
Displayed below is the user manual for SSB169 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802- 000237 RevB
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Place felt pads on inner corners of top and bottom to protect projector.
3. Align Brac ket B threaded holes with slots in Bracket A, and install the 10-24 x 1/4" screws loosely enough so brackets slide in the slot.
4. Turn projector upside down.
5. Slide bracket assembly open and slide the projector into Bracket A.
6. Slide Brac ket B in until both brackets are touching projector.
7. Place the bracket assembly onto bottom of projector and align the holes in bracket assembly with the threaded inserts in bottom of
projector. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Se curity sc rews c an be substit ute d when mount ing in terface br acke t to projec tor by usi ng the par ts and i nstallat i on inst ructions i n the
All-Poi nts Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
SSB-169, SSM-169, SLB-169 and SLM-169 Interface Brackets
SSB-169, SSM-169, SLB-169 and SLM-169 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the
specific installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY
AND DAMAGE TO EQUIPMENT! DO NOT substitute hardwar e. Use only hardware supplied by manufacturer!
(1) Interface Br acket A (8) PAD, Felt
(1) Interface Br acket B (2) Screw, Phillips Pan Head, 10-24 x 1/4"
(4) 10-24 Thumb Nuts ** (1) All-Points Security Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Sp eci fic t o SSB-st yl e a nd SSM-style inte rface bracket i nst al la tion, al l appropriate screws come pre- in sta lled as reflecte d in t he
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-
style interface br acket installat ion.
SLB-169 SLM-169
Felt Pad
(8 pl aces)
Fel t Pad
(8 places) Bracket A
Bracket B
Bracket B
Bra cket A
Towards front of
projector
Towards front of
projector
(Note: SSM-style interface bracket con n ection
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: SSB-sty le int erface brack et connections
a
r
e
e
n
c
i
r
c
l
e
d
)