Chief SSB218 User Manual
Displayed below is the user manual for SSB218 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0025 2 R ev 01
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
SSB-185, SSM-185, SLB-185 and SLM-185 Interface Brackets
SSB-185, SSM-185, SLB-185 and SLM-185 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place 1/2" nylon spacers over threaded inserts in bottom of projector.
4. Place interface bracket onto the 1/2" nylon spacers and align the mounting holes in bracket with holes in spacers.
5. Position M4 x 20mm flat head screws into countersunk holes in bracket.
6. Position the M4 x 20mm pan head screw with an M4 washer into threaded insert in projector. Tighten all fasteners at this time, securi ng
the bracket to the projector.
NOTE: Se curity sc rews c an be substit ute d when mount ing in terface br acke t to projec tor by usi ng the par ts and i nstallat i on inst ructions i n the
All-Poi nts Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (1) Screw, Phillips Pan Head, Machine, M4 x 20mm
( 6) 10- 24 Thumb Nu ts * * (1) Washer, M4
(1) All-Poi nts Secu rity Kit (2) Screw, Phillips Flat Head, M4 x 20mm
(3) Spacer, 1/2" x 1/2"
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encirc led locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
SLB-185 SLM-185
Tow ards front of
projector
Tow ards front of
projector
(Note: SSM-style interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)
(
Note: SSB-style interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)