Chief SSM036 User Manual
Displayed below is the user manual for SSM036 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0201 5 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
SSB-036, SSM-036, SLB-036 and SLM-036 Interface Brackets
SSB-036, SSM-036, SLB-036 and SLM-036 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit conten ts. If any listed parts are missing, immediately contact a Ch ief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing Interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. Place the ¼” nylon spacers over the threaded inserts on the bottom of the projector.
4. P lace the i nterface brack et onto th e ¼” nylon spacers on the bottom of the project or and align the mounting holes in the bracket with the
nylon spacers.
5. Place the flat head screws into the two countersink holes and place the M4 x 16mm pan head screws with the M4 flat washers into the
remaining threaded inserts. Tighten all four fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (2) M4 Flat washer
(4) 10 - 24 Thumb Nuts** (2) M4 -16mm Phillips Pan Scr ews
(1) All-Po ints Secu rity Kit (4) 1/2" x .219 x 1/4" Nylon Spacer
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encirc led locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
SLB-036
SLM-036
(Note: SSM
-style in
terface
bracket
connect
ions
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: S
SB-styl
e interfa
ce brack
et conn
ections
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards f ront of
projector
Towards f ront of
projector