Chief SSM060 User Manual
Displayed below is the user manual for SSM060 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-0 0005 2 R ev 01
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
SSB-060, SSM-060, SLB-060 and SLM-060 Interface Brackets
SSB-060, SSM-060, SLB-060 and SLM-060 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
install ation instructi ons provided wi th the mount fo r additional inst allation information. Unpack c arton and ve rify kit content s. If any listed parts
are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10 - 24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Using bottom interface bracket and rubber bump-ons, push one bump-on into each hole of bracket from inside.
4. Slide top interface bracket onto bottom bracket (i.e., so front of projector is toward two tabs sticking up, and the top of projector is sitting
on the rubber bump-ons).
5. Place interface bracket over bottom bracket (i.e., so two tabs are toward back of projector and down to prevent projector from sliding).
6. Align mounting holes in top bracket with threaded inserts in bottom bracket.
7. Using four 10-24 x 3/8" Phillips pan head screws and flat washers, secure interface to projector and tighten all fasteners at this time.
NOTE: Sec urity scr ews can be substit uted wh en mounting interface brack et to proj ector b y usi ng the par ts and ins tallat ion inst ruct ions
in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Bracket, Bottom (4) Screw, Philli ps Pan Head, Machine, 10- 24 x 3/8"
(1) Bracket, Top (4) Rubber Bumper Spacer
(4) 10-24 Thumb Nuts ** (4) #10 Washer
(1) All-Points Security Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encirc led locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
SLB-060 SLM-060
(Note:SSM-styleinterfacebracketconnections
areencircled)
(Note: SSB-style interfacebracketconnections
areencircled)