Chief SSM134 User Manual
Displayed below is the user manual for SSM134 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-0 0012 3 R ev 01
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
SSB-134, SSM-134, SLB-134 and SLM-134 Interface Brackets
SSB-134, SSM-134, SLB-134 and SLM-134 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAB LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place interface bracket onto bottom of projector and align bracket with the threaded inserts in projector.
4. Place M4 x 10mm Phillips pan head screws and flat washers into mounting holes.
5. Place 1/2" spacer between interface bracket and projector and align spacer with last mounting hole.
6. Using M4 x 20mm Phillips pan head screw with flat washer and M4 x 10mm Phillips pan head screws with flat washers, secure interfac e
bracket to projector and tighten all fasteners at this time.
NOTE: Security s crews can be s ubsti tuted when mou nting int erface b racket to pr oject or by using t he parts a nd insta llatio n instruct ions
in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) Screw, Phillips Pan Head, Machine, M4 x 10mm
( 4) 10- 24 Thumb Nu ts * * (1) Screw, Phillips Pan Head, Machine, M 4 x 20mm ****
(1) All-Poi nts Secu rity Kit (1) 1/2" x .194" x 1/2" Round Spacer ****
(4) Wa sher, Flat, M 4
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encirc led locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
SLB-134 SLM-134
Towards front of
projector
Towards front of
projector
(Note: SSM-styl e interface bracket co nnection
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
Note: SSB-style in terface bracket conn ections
a
r
e
e
n
c
i
r
c
l
e
d
)