Chief SSM140 User Manual
Displayed below is the user manual for SSM140 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-0 0012 9 R ev 02
©2012 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
01/12
SSB-140, SSM-140, SLB-140 and SLM-140 Interface Brackets
SSB-140, SSM-140, SLB-140 and SLM-140 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to Step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place interface bracket onto bottom of projector and align bracket with the threaded inserts in projector.
4. Po sition M6 x 12mm Phillips pan head sc rews and flat was hers and plac e 5/8" tal l spacer bet ween remai ning hol e in brac ket and thre aded
insert in projector.
5. Using M6 x 25mm Phillips pan head screw, secure interface bracket onto projector and tighten all fasteners at this time.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) Washer, Flat M6
( 6) 10- 24 Thumb Nu ts * * (3) Screw, Phillips Pan Head, Machine, M6 x 12mm
(1) All-Poi nts Secu rity Kit (1) Screw, Phillips Pan Head, Machine, M6 x 25mm ****
(1) 1/2" x .257" x 5/8" Nylon Spacer ****
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific t o SSB-styl e and SSM-styl e interface br acket ins tallation : All appropriate s crews come p re-installed i n the circled l ocations
above. DO NOT attempt to substitute and USE ONLY this pre-installed har dware for SSB-styl e and SSM- style interface bracket
installation.
Towar d s front
of projector Towards front
of projector
SLB-140 SLM-140