Chief SSM170 User Manual
Displayed below is the user manual for SSM170 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0023 8 R ev C
©2009 Mil eston e AV Technologies,
a Ducho ssois Group Comp any
05/09
SSB-170, SSM-170, SLB-170 and SLM-170 Interface Brackets
SSB-170, SSM-170, SLB-170 and SLM-170 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. Place the 1/2" nylon spacers over the threaded inserts in the bottom of the projector.
4. Plac e the interface br acke t ont o the 1/2" nylo n spacer s on the b ottom of th e p roject or a nd ali gn t he mo unting ho les i n the brack et with the
nylon spacers.
5. Us ing the M4 x 20mm screws, position screws into t he four threaded inserts and tighten all fasteners at this time, securing the bracket to
the project or.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All- Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (2) Screw, Phillips Flat Head, Machine, M4 x20mm
(4) 10 - 24 Thumb Nuts ** (2) Screw, Phillips Pan Head, Machine, M4 x20mm
(1) All-Points Security Kit (2) Was her, Fl at, M4
(4) Spacer, Nylon, 1/2" x .194 x 1/2"
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
enci rc led loc ations a bove. DO NOT at tempt to s ubst itut e and USE O NLY thi s pre- ins talled hardware for SSB-s tyle an d S SM-styl e
interface bracket installation.
SLB-170 SLM-170
To wards front of
projector
To wards front of
projector
(Note: SSM-style interface bracket connection
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
Note: SSB-style interface b racket connections
a
r
e
e
n
c
i
r
c
l
e
d
)