Chief SSM272 User Manual
Displayed below is the user manual for SSM272 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
8802-0 02 06 9 R ev 00
©2010 Mile stone AV Technologies,
a Duchossois Group Company
10/10
INSTALLATION INSTRUCTIONS
Milestone AV T ec hnol ogie s, and its affi liated corporat ions a nd subsidiaries (c ol lectiv el y, "Milestone"), i ntend to make this manual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation containe d h erein co vers all details, con ditions or variatio ns, nor does it pro vide for ev ery possible contingency in connection with the i nsta llation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expr essed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
SSB-272, SSM-272, SLB-272 and SLM-272 Interface Brackets
SSB-272, SSM-272, SLB-272 and SLM-272 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack c arton and veri fy kit contents. If any listed parts are missing, im mediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector, aligning the mounting holes in the bracket with the threaded inserts in the
bottom of the projector and ensuri ng that triangle in bracket points towards front of pr ojector.
4. Position M4 x 10mm mount ing sc rews in to the threade d inser ts and t hree br acket side tabs. Tig hte n all fas teners at t his ti me, secur ing the
bracket to the projector.
NOTE: Security s cr ews can b e subs titu ted wh en mounti ng In terfa ce bracke t to proje ctor by u sin g the part s an d insta llat ion in struct ions i n the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket ( 3) Scr ew, Phi ll ips Pan Head, Machi ne, M 4 x 1 0mm
(4) 10-24 Thumb Nuts ** (1) 5/32" Security Hex Key
(1) All-Points Security Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.
SLB-272 SLM-272
Towards front
of projector Towards front
of projector