Chief SSM303 User Manual
Displayed below is the user manual for SSM303 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
Milestone AV Tec hnol ogie s, and its affiliated corpo rat ions and subsidiaries (collectiv el y, "Miles tone"), intend to mak e th is ma nual accurate an d compl ete. However, Mi lestone mak es
no claim that the information con tained herein co vers all deta ils, con ditions or variations, nor does it provide for every possible conti ngency in connection with the i nstallation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty , expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility fo r accuracy, completeness or suffici ency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
6436 City West Parkway, Eden Prairie, MN 55344
• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 / 952.894.6918
8800-0 02 20 8 R ev 00
©2012 Mil estone AV Technologies,
a Ducho ssois Group Comp any
07/12
INSTALLATION INSTRUCTIONS
SSB-303, SSM-303, SLB-303 and SLM-303 Interface Brackets
SSB-303, SSM-303, SLB-303 and SLM-303 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack c arton and ver ify kit contents. If any listed parts are missing, immediately contact a Chief Cust omer Service repres entative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector, aligning the mounting holes in the bracket with the threaded inserts in the
bottom of the projector and ensuring that tri angle in bracket points towards front of projector.
4. Position M4 x 10mm mounting screws with M4 flat washers into the threaded inserts and five bracket side tabs. Tighten all fasteners at
this time, securing the bracket to the projector.
NOTE: Security s cr ews can b e subs titu ted wh en mounti ng In terfa ce bracke t to proje ctor by u sin g the part s an d insta llat ion in struct ions i n the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (5) Screw, Button Head, Security, M4 x 10mm
(4) 10-24 Thumb Nuts ** (5) Screw, Phillips Flat Head, Machine, M4 x 10mm
(1) All-Points Security Kit (5) Washer, M4
(1) 5/32" Security Hex Key
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.
DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.
SLB-303 SLM-303
Towards front
of projector
Towards front
of projector