Chief SSM308 User Manual
Displayed below is the user manual for SSM308 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
8800-002281 Rev01
©2012 Milestone AV Technologies,
a Duchossois Gr oup Company
12/12
Milestone AV Tec hnol ogies, and its affiliated co rpo rat ions and subsidiaries (collectivel y, "Miles tone"), intend to mak e th is ma nual accurate and complete. However, Milestone mak es
no claim that the in for mation containe d h erein co vers all details, con ditions or variatio ns, nor does it pro vide for ev ery possible contingency in connection with the i nsta llation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
6436 City West Parkway, Eden Prairie, MN 553 44
• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 / 952.894.6918
INSTALLATION INSTRUCTIONS
SSB-308, SSM-308, SLB-308 and SLM-308 Interface Brackets
SSB-308, SSM-308, SLB-308 and SLM-308 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack c arton and verify kit co ntents. If any listed parts are missing, im mediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM /SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. D O NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place five spacers over threaded inserts in bottom of projector.
4. Place the interface bracket onto the spacers on bottom of the projector, aligning the mounting holes in the bracket with the spacers and
threaded inserts in the bottom of the projector and ensuring that triangle in br acket points towar ds front of proj ector.
5. Position M4 x 20mm mounting screws into the mounting holes in interface bracket through spacers and into threaded inserts. Tighten all
fasteners at this time, securing the bracket to the projector.
NOTE: Security s cr ews can b e subs titu ted wh en mounti ng In terfa ce bracke t to proje ctor by u sin g the part s an d insta llat ion in struct ions i n the
All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (5) Screw, Phillips Flat Head, Machine, M4 x 20mm
(4) 10-24 Thumb Nuts ** (5) Spacer, .500 x .316 x .500
(1) All-Points Security Kit (1) 5/32" Security Hex Key
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.
DO NOT attempt to substitute and USE ONLY this pre-installed hardw are for SSB-style and SSM-style interface bracket installation.
Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.
SLB-308 SLM-308
Towards front
of proj ector
Towards front
of projector