Chief SSM710 User Manual
Displayed below is the user manual for SSM710 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-0 0019 9 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
SSB-710, SSM-710, SLB-710 and SLM-710 Interface Brackets
SSB-710, SSM-710, SLB-710 and SLM-710 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit conten ts. If any listed parts are missing, immediately contact a Ch ief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Align mounting holes in bracket with threaded inserts in projector.
4. Insert two machine screws and tighten moderately.
5. Place U-form wire bracket towards rear of projector and through holes in tabs of interface bracket. Thread Nylock nut onto each side of
U-form wire bracket and tighten moderately.
6. Tighten all fasteners at this time, securing interface bracket to projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (2) M4-7 x 12mm Machine Screws
(6) 10 - 24 Thumb Nuts** (4) Fel t Squares
(1) All-Points Security Kit (2) M4 Flat washers
(1) U-form Wire Bracket (2) 10-24 Nylock Nuts
(2) #10 Flat washers
**Only used when installing SLB/SSB interface brackets.
NOTE: Specifi c to SS B-style and SSM- style interf ace bracket in sta llation, all appropriat e screws come pre- installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-
style interface br acket installat ion.
SLB-710
SLM-710
(Note: SSM-styl e interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: SSB-style interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector