Chief SSM7720 User Manual
Displayed below is the user manual for SSM7720 by Chief which is a product in the Projector Mount Accessories category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0009 2 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
SSB-7720, SSM-7720, SLB-7720 and SLM-7720 Interface Brackets
SSB-7720, SSM-7720, SLB-7720 and SLM-7720 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the
specific installation instructions provided with the mount for additional instal lation information.
Unpack carton and verify kit conten ts. If any listed parts are missing, immediately contact a Chief Cu stomer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Remove the front adjustable foot on projector by lifting up the finger tab and sliding it in the direction of the finger tab (see Figure 1).
(1) Interface Bracket (2) Screw, Phillips Pan Head, M4 -20mm
( 4) 10- 24 Thumb Nu ts * * (1) Screw, Flat Head, M3x 16mm
(1) All-Poi nts Secu rity Kit (2) Wa sher, Flat, M 4
(3) Spacer, Nylon, .500 x .194 x .500
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encirc led locati ons abov e. DO NOT attempt t o subst itute a nd USE ONLY thi s pre-in stalled hardware for SSB-sty le and SSM-st yle
interface bracket installation.
SLB-7720 SLM-7720
Towards front of
projector
Towards front of
projector
(Note: SSB-style interface bracket connections
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: SSM-style interface bracket connection
s
are encircled)
INSTALLATION INSTRUCTIONS
Milestone AV Tec hnol ogie s, and its affiliated co rpo rat ions a nd subs idiaries (c ol lectiv el y, "Miles tone"), intend to make this ma nual ac cu rat e an d compl ete. However, Mi lestone makes
no claim that the in for mation con taine d h erein co vers all deta ils, con ditions or va ri atio ns, nor does i t provide for every pos sible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone as sumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-0 0009 2 R ev 01
©2009 Milestone AV Te chnologies,
a Duchossois Group Company
05/09
Figure 1: Finger Tab
4. Place the ½" nylon spacers over the threaded inserts in the bottom of the projector.
5. P lac e the interface bracket onto the ½" nylon spacers on the bottom of the proj ect or and align the mounting holes in the bracket wi th the
nylon spacers.
6. P osi tion the M 4 x 20mm button head screws and M4 x 16mm flat head screw through the hol e in the bracket and nylon spacer, and then
place into the threaded inserts. Tighten all fasteners at this time to secure interface bracket to projector
NOTE: Securit y screws can be subst ituted whe n mountin g interface brac ket to proje ctor by usi ng the par ts and i nstall ation instruct ions in t he
All-Points S ecurit y Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.