Chief TIL1X5PH User Manual
Displayed below is the user manual for TIL1X5PH by Chief which is a product in the Signage Display Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
TILVAB1 Accessory
TIL1X2PH
TIL1X3PH
TIL1X4PH
TIL1X5PH
PH Series LED Wall Mounts / Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH /
TILVAB1
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
Chief® is a registered trademark of Legrand AV Inc.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system. The wall to which the
mounting system is being attached may have a maximum
drywall thickness of 5/8” (1.6cm).
WARNING:
The TIL1X2PH / TIL1X3PH / TIL1X4PH /
TIL1X5PH LED wall mounts are designed for use with LED
panels only. Exceeding the weight capacity (listed) can result
in serious personal injury or damage to equipment!
• TIL1X2PH: 40 lbs (18.1 kg) - 20 lbs (9.1 kg) per
screen;
• TIL1X3PH: 60 lbs (27.2 kg) - 20 lbs (9.1 kg) per
screen;
• TIL1X4PH: 80 lbs (36.3 kg) - 20 lbs (9.1 kg) per
screen;
• TIL1X5PH: 100 lbs (45.4 kg) - 20 lbs (9.1 kg) per
screen.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mounting system outdoors.
IMPORTANT ! : The TIL1X2PH / TIL1X3PH /TIL1X4PH
/
TIL1X5PH
LED wall mounts are designed to be mounted to:
• a bare 8" concrete or 8"x8"x16" concrete block wall; or
• a 3/4" thickness plywood-backed, 2" x 4" wood studs
(16" on center minimum) wall with a maximum drywall
thickness of 5/8"; or
• a 3/4" thickness plywood-backed, steel stud wall
covered with drywall having a maximum thickness of
5/8".
--SAVE THESE INSTRUCTIONS--
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
4
TABLE OF CONTENTS
DISCLAIMER ......................................................................2
DEFINITIONS .....................................................................2
IMPORTANT SAFETY INSTRUCTIONS ...........................2
LEGEND .............................................................................3
TABLE OF CONTENTS ......................................................4
TOOLS REQUIRED FOR INSTALLATION .........................5
PARTS ................................................................................5
PRE-INSTALLATION ..........................................................6
Site Assessment ......................................... ................................. 6
INSTALLATION ..................................................................7
Adding Vertical Connector Kit ..................... ................................. 7
If Starting LED Wall Installation With the Top Row ....................... 7
If Starting LED Wall Installation With the Bottom Row ................. 7
Assessing the Installation Site....................................................... 8
Installing First Mount ..................................................................... 8
Adding Additional Mounts ........................... .................................11
Checking Placement and Alignment .............................................12
Connecting Mounts Above or Below First Row .............................13
Installing the Cabinets and LED Panels ........................................14
Fastener Installation Methods .......................................................15
Wood Stud .........................................................................15
Concrete or Concrete Block ...............................................15
Steel Stud ...........................................................................16
Site Requirements for Wood or Steel Stud Installation..................17
DIMENSIONS ............................................................................................18
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
Hardware Required - not included
(for installation into steel stud walls)
1. Chief brand FCAT1 Toggler Kit; OR
2. Hardware for installation to steel stud wall:
• 1/4-20 Toggler Snaptoggle BB (Qty 4)
•1/4-20 x 2-1/2" hex head bolt (Qty 4)
• 1/4" washer (Qty 4)
7/32"
#2, #3
Level
[2 ft. long]
[Small level]
3/8"
1/2"
square drive
[4+ ft. long]
[6+ ft. long]
Bright colored
string
Additional Suggestions
1. Dead blow hammer
2. Masking tape
3. Offset screwdrivers
4. Ratcheting wrenches
5. Laser level
6. Tools required for LED
panels installation.
Most likely metric.
3/4" (19mm)
ratcheting wrench
deep well socket
5/32"
ball end hex key
(included)
A (1)
[Adjustment
washer-RIGHT]
C (4)
[UX10x60R D (4)
5/16 x 2-1/2"
E (4)
5/16"
anchor]
B (1)
[Adjustment
washer-LEFT]
Mounting Hardware Kit
F (6)
#10 x 1/2"
G (8)
10-24 x 1"
H (5)
1/4-20 x 1/2"
N (2)
TILVAB1 Vertical Connector Kit
M (8)
1/4-20 x 1/2"
[Vertical connector]
[Sold separately]
*Quantities above listed as:
TiL1X2PH / TiL1X3PH / TiL1X4PH / TiL1X5PH
TILXXXPH Hardware Kit
J (1)
5/32"
M8 Mounting Button Kit
K (8/12/16/20)
L (8/12/16/20)
[Spacer]
[Mounting Button
assembly]
P (1)
[TIL1X2PH]
P (1)
[TIL1X3PH]
P (1)
[TIL1X4PH]
P (1)
[TIL1X5PH]
OR
OR
OR
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
6
PRE-INSTALLATION
IMPORTANT ! : Reference the LED screen installation
manual for specific instructions regarding care, handling,
cabling and installation of the LED screens.
CAUTION: Handle the cabinets and LED screens with
care, being careful to not impact or drop the LED screen.
CAUTION: There is a magnetic surface on the front of the
LED screen. To prevent damage ensure that no metallic
object is pulled onto the LED screen.
NOTE: When planning the installation, remember the
requirement to run power and signal to the video wall.
Ensure there is also adequate clearance for the plug
head. Recessed outlets or angled plugs may be
required.
Site Assessment
Before beginning any installation the site should be assessed in
several areas to help avoid any issues during the actual
installation.
•Wall Structure - It is recommended that a 3/4"
furniture-grade plywood-backed wall be used in most
LED video walls. The use of a wood stud wall is not
appropriate since the studs won’t be in the proper
location for an LED video wall.
•Wall High/Low Points - Locate any high or low points
on the wall that may cause problems, and try to set up
install so that these points can be avoided, if possible.
•Flatness/Plumb of Wall - Learn how much depth
adjustment will be needed across the LED video wall
mounting area.
•Power/Cable - Locate all power outlets and cable
access holes that need to be cleared by the installation.
Plan appropriately for those holes.
•Installing in a Recess - Verify the level and
squareness of the recessed area. Since these areas
are rarely perfect you may need to decide what to use
as a reference point.
•The recess top or bottom may not be level so the
video wall may need to be installed to align with
the recess, rather than being level with the wall.
• If the recess is not square the sides may make the
recess look crooked. If possible, the recess
should be fixed. If repairing the recess isn’t an
option it may be best to "split the difference"
between the recess sides to make the video wall
appear level.
•Where to Begin the Video Wall - The installer should
make the decision whether the video wall will be started
at the top, bottom, left, right or center.
• If a lower bottom reference is given in the
specifications, it may make sense to start at the
bottom of the video wall to ensure that this
specification is met from the start of installation.
• If building inside of a recess, it may be easier to
start in the center of the space since the video
wall will most likely need to be centered within the
recess.
• Vertical Connector Brackets - If creating a video wall
with more than a single row you will be using the
TILVAB1 vertical connectors which are sold
separately.
•
Vertical Connector Brackets [sold separately]
If the video wall requires multiple rows, decide on
whether the installation will start with the top or
bottom row. This determines to which end (top or
bottom) the vertical connector brackets are
attached.
Figure 1
Just a tip - For larger LED walls it is helpful to
check placement and alignment of the mounts by
putting a few cabinets without the LED’s in place in
the bottom row of the installed mounts (referencing
the LED screen installation manual for specific
instructions) during the mount installation, verifying
that everything is staying aligned and level, and
then continuing the mount installation.
Just a tip - The horizontal slots located along
the vertical mount pieces (and vertical slots
located along the horizontal mount pieces) are the
center-of-screen indicators to illustrate where the
center of each LED screen will be located, and can
be used to hold a tape measure tab while
measuring. (See Figure 1)
= Center-of-screen indicators
Tape
Measure
[TIL1X3PH shown as example]
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
7
INSTALLATION
Adding Vertical Connector Kit
NOTE: If more LED screens will need to be added to the top or
bottom of the screen configuration, add TILVAB1
vertical connector kit to top or bottom of wall mount
using the following instructions. If you are NOT adding
the TILVAB1 connector kit, proceed to Installing First
Mount section.
IMPORTANT ! : Install the vertical connector kit
BEFORE the mounts are attached to the wall.
If Starting LED Wall Installation With the Top Row
NOTE: If you’re starting the installation at the top of the LED
video wall, the vertical connector brackets should be
attached to the BOTTOM of the mounts to create the
top row and each successive lower row.
1. Slide the vertical connector (N) up from the bottom of the
mount, and attach with two 1/4-20 x 1/2" Phillips pan head
screws (M) per vertical connector. (See Figure 2)
2. Loosely install one 1/4-20 x 1/2" Phillips pan head screw (M)
in the upper screw hole at the bottom of each vertical
connector (N). (See Figure 2)
Figure 2
If Starting LED Wall Installation With the Bottom Row
NOTE: If you’re starting the installation at the bottom of the
LED video wall, the vertical connector brackets should
be attached to the TOP of the mounts to create the
bottom row and each successive upper row.
1. Slide the vertical connector (N) down from the top of the
mount, and attach with two 1/4-20 x 1/2" Phillips pan head
screws (M) per vertical connector. (See Figure 3)
2. Loosely install one 1/4-20 x 1/2" Phillips pan head screw (M)
in the lower screw hole at the top of each vertical connector
(N). (See Figure 3)
Figure 3
(N)
(M) x 2
1
2
(M)
1
(L)
Mount
(M) x 2
1
1
2
(M)
(N)
Mount
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
8
Assessing the Installation Site
IMPORTANT ! :
The top of the LED panel is 3.5" above
the top of the
UPPER
mounting slots, and the bottom of
the LED panel is 4.25" below the top of the
LOWER
mounting slots. (See Figure 4)
NOTE: If desired, the mount installation may be started in the
middle of the video wall, attaching mounts out from the
center to the left and right ends. (Review Site
Assessment section for further information.)
Installation on smaller walls may be easier if started at
the left or right side of the video wall using the following
instructions.
1. Determine top or bottom panel height location and
horizontal placement of mounts. (See Figure 4)
2. Make a mark 3.5"
below
the planned top edge (or 4.25"
above
the planned lower edge of the LED wall. (See Figure 4)
3. Using a level, mark a horizontal line across width of LED
wall from the mark made in Step 2.
NOTE: If available, a laser level would be helpful at this point.
NOTE:
This line will be located at the top of the mounting slots
across the width of the LED video wall. The oversize
mounting slots will allow some upward adjustment as
needed. (See Figure 4)
Figure 4
Installing First Mount
The TIL1X1IFH / TIL1X2IFH /TIL1X3IFH LED wall mounts are
designed to be mounted to:
• a bare 8" concrete wall or 8"x8"x16" concrete block
wall; or
• a 3/4" thickness plywood-backed, 2" x 4" wood studs
(16" on center minimum) wall with a maximum drywall
thickness of 5/8"; or
• a 3/4" thickness plywood-backed, steel stud wall
covered with drywall having a maximum
thickness of 5/8".
Table 1: Fastener Information
1. Make final decision on where to begin the LED video wall
installation (left, right or center; and top or bottom).
2. Make sure the vertical connectors are attached to top or
bottom depending on installation decision.
3. Place mount against wall matching the top of the mounting
slots with the horizontal line previously drawn.
4. Mark mounting holes in two top mounting slots along the
horizontal line marked in Step 3 of Assessing the
Installation Site section. (See Figure 5)
NOTE: The mounting holes are 17.53" apart on-center. (See
Figure 5)
Figure 5
Just a tip - It is often a good idea to review
installation instructions and dimensional drawings
(at end of instructions), and then utilize masking
tape to lay out the entire LED video wall to lessen
the chance of any surprises later in the installation.
3.5”
4.25”
3.5”
4.25”
Bottom of LED cabinet
Top of LED cabinet
[TIL1X2PH mount shown - Wall side - Rear View]
2
2
3
Horizontal
mark through
top of mount
slots
WALL
TYPE PILOT
HOLE FASTENERS (see PARTS
drawing)
Drywall
attached to
plywood-
backed walls
/Steel studs
Drywall
attached to
plywood-
backed walls
/Wood studs
1/2"
7/32" x 3"
- 1/4-20 x 2-1/2" hex head lag (not
included)
- 1/4" washer (not included)
- 1/4-20 Toggler Snaptoggle BB
(not included)
- 5/16 x 2-1/2" flanged hex head
lag (D)
- 5/16" washer (E)
- Adjustment washers (A, B)
Concrete or
concrete
block
3/8" x 3" - 5/16 x 2-1/2" flanged hex head
lag (D)
- 5/16" washer (E)
- Adjustment washers (A, B)
- Fischer Anchor UX10x60R (C)
4
17.53 inches
5
Line showing top
of mounting slots
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
9
5. Drill two pilot holes (see Table 1 for size) at each location
marked in Step 4 (See Figure 5) and follow fastener
information (appropriate for wall type) located in Table 1.
IMPORTANT ! : Refer to Fastener Installation Methods
(located in Appendix at end of Installation Instructions)
for details on installing product into various wall types.
6. Partially install two lag screws into wall, but do NOT
completely tighten to wall. (See Figure 6)
NOTE: Utilizing the two adjustment washers (A, B) allows the
installer to pre-install the top mounting fasteners and
hang the mount from them utilizing the mounting slots.
This allows the weight of the mount to be held by the
mounting bolts during installation, and not the installer.
Figure 6
7. Hang wall mount, aligning upper mounting slots over
fasteners, and adjust side-to-side for proper location. (See
Figure 6)
8. Place a level across front of the mount at bottom of teardrop
slots. (See Figure 7)
9. Check the level of the mount at the teardrop slots. (See
Figure 7)
Figure 7
10. Slide the left (B) and right adjustment washers (A) into place
behind the partially installed lag screws. (See Figure 8)
Figure 8
11. Check the level of the mount at the bottom of the teardrop
slots. (See Figure 9)
12. If the mount is not level, slide or use a dead blow hammer
to lightly tap the spacer into place. This will lift the mount up
as the lag screw rides in the washer’s angled slot. (See
Figure 9)
13. When the mount is leveled, tighten the lag screws (D). (See
Figure 9)
Figure 9
7
x 2
[TIL1X1IFH shown
6
as example]
8
Mount
teardrop
Level
slots
(B)
(A)
10
Just a tip - Tighten down the lag screw on the
side that does NOT need to be raised. This
creates a pivot point for when the opposite
adjustment washer is tapped into place, and
allows that correct side of the mount to move up.
Level
Dead blow
hammer
(B) (A)
13
(D) x 2
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
10
14. Drill pilot holes in centerline of lower slots (see Table 1 for
size) and follow fastener information (appropriate for wall
type) located in Table 1. (See Figure 10)
15. Double check the level of the mount at the center-of-screen
indicators. (See Figure 10)
16. Fully tighten the 5/16 x 2-1/2" lag screws (D) through the 5/16"
fender washers (E). (See Figure 10)
Figure 10
17. Using a level on the front of the mount in various places, use
a 3/4" or 19mm deep-well socket and square drive
ratcheting wrench to adjust the leveling feet on the mount
until the mount is plumb or even with something that is being
used as a reference point. (See Figure 11)
CAUTION: Over-torquing may cause damage. Do NOT
use a drill to make the depth adjustment.
Figure 11
16
(E) x 2
15
(D) x 2
Center-of-screen
indicator
14
x 2
Just a tip - After the first mount is installed, it
may be easier to adjust the plumb at this time. If a
lot of adjustment is going to be necessary it’s best
to adjust it right away to avoid any twist or tension
on the mount.
Leveling feet
locations
17
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
11
Adding Additional Mounts
1. Partially install one 1/4-20 x 1/2" button head screw (H) into
fastener hole next to tear drop slot at each mid-screen area
on the right side of mount. (See Figure 12)
Figure 12
2. Hang the second mount (matching up teardrop slots on the
left side) onto the fasteners installed in Step 1. (See
Figure 13)
3.
Level mount then tighten fasteners installed in Step 1 through
teardrop slots on second mount.
(See Figure 13)
Figure 13
4.
Drill pilot holes towards top and in centerline of upper
mounting slots on second mount (see Table 1 for size) and
follow fastener information (appropriate for wall type) located
in Table 1. (See Figure 14)
Figure 14
5. Hang second wall mount, aligning upper mounting slots
over fasteners, and adjust side-to-side for proper location.
6.
Slide the left (B) and right adjustment washers (A) into place
behind the partially installed lag screws.
7. Slightly loosen the side connector screws prior to adjusting
the mount height. (See Figure 12)
8. Place a level across front of the mount at bottom of teardrop
slots and check that mounts are level and in line with each
other.
9. If mount needs to be raised: use the adjustment washers to
raise the second mount.
10. Re-tighten connector screws. (See Figure 12)
11. Drill lower pilot holes at the center both vertically and
horizontally within lower mounting slots and use same
fasteners used at top of mount.
12. Continue installation of mounts in this manner until the row
is complete.
Model Fastener
Qty
(total)
TIL1X2PH 2
TIL1X3PH 3
TIL1X4PH 4
TIL1X5PH 5
1
(H)
[TIL1X3PH shown as example]
3
3
(H) x 3 Second
wall mount
Teardrop slot
2
1
Just a tip - The plumb on these mounts at this
point doesn’t have to be perfect. Final adjustments
can be done once all the mounts are installed.
Checking and adjusting plumb at this point
ensures the mounts are closely aligned on the
same plane to prevent the mount from twisting or
bending when the lag screws are installed.
4
x 2
Just a tip - The lag screws need to be at the
top of the mounting slot to allow the mount to be
raised slightly, if needed, to align it with the
previously installed mount.
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
12
Checking Placement and Alignment
1. The holes around slots on the mounts can be used for the
included #10 x 1/2" self-tapping screws (F) to help attach a
string to help in aligning and plumbing the mounts.
NOTE: There are multiple points on each mount where the
screws can be installed for the plumb line. At a
minimum, the plumb strings should be strung next to
each adjustment point (at every leveling foot). (See
Figure 15)
2. Loosely install the self-tapping screws then wrap the string
around the screw and tighten. (See Figure 15)
3. Run the string tightly between the same hole at each end of
the row of mounts. (See Figure 15)
Figure 15
1
Ovals indicate tapping
screw hole locations for
attaching string to assist
with alignment of mounts
String to
assist with
alignment
2
3
Leveling feet
(top and bottom,
of each mount)
left and right
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
13
4. Insert the proper number of 10-24 x 1" self-tapping screws
(G) into the left side of the mount. (See Figure 16)
NOTE: There are two places at each LED cabinet section of
the mount for the left side stop screws to be installed.
These screws will act as an adjustable left stop. Turn
the screw IN to adjust the stop to the right, and back
the screw OUT to move the stop to the left.
Figure 16
Connecting Mounts Above or Below First Row
• Hanging Mounts from an Upper Row
1.
Hang the lower mount on the partially installed
Phillips head screws (M) in the vertical connectors
(N). (See Figure 17)
2. Tighten both lower screws (M) on both vertical
connectors (N). (See Figure 17)
Figure 17
NOTE: There
are 2 places at
each cabinet for
left side stop
screws to be
installed.
4
(G)
4
Installed
mount
1
(N)
Lower
mount
(M) x 2
2
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
14
• Installing Mounts onto a Lower Row
3. Make sure the 1/4-20 x 1/2" Phillips head screw
(M) is already loosely installed in the vertical
connector (N) on both sides of the mount. (See
Figure 18)
4. Slide mount down onto the screws so that upper
mount hangs on lower mount.
5. Install two 1/4-20 x 1/2" Phillips head screws (M)
into upper hole on both vertical connectors, and
tighten all screws. (See Figure 18)
Figure 18
6. Place a long level against front of the mounts and adjust the
depth of the newly attached mount to align it with the first,
installed mount.
7. Adjust the leveling feet on the newly installed mount so that
they are touching the wall.
8. Drill pilot holes in centerline of each mounting slot on each
leveling foot of the added mount (see Table 1 for size) and
follow fastener information (appropriate for wall type) located
in Table 1. (See Figure 19)
9. Double check the level of the mount at the bottom of the
teardrop slots, and make sure the new mount stays
perfectly aligned with the upper or lower mount to which it
was attached. (See Figure 19)
10. Fully tighten the 5/16 x 2-1/2" lag screws (D) through the 5/16"
fender washers (E). (See Figure 19)
Figure 19
11. Continue on until the entire LED mount wall is assembled.
Installing the Cabinets and LED Panels
1. Attach four mounting buttons (L) and four spacers (K) to
each LED cabinet, one to each corner of the cabinets. (See
Figure 20)
Figure 20
2. When installing a cabinet to the mounting system, line up
mounting buttons with mounting holes at each corner.
3. Guide cabinet mounting buttons into mounting holes and
lower cabinet ensuring that mounting buttons are securely
seated in the four mounting holes. (See Figure 21)
(M) x 2
5
Hang mount
3
4
Installed
mount
4
on loosely
installed screw
10
(E) x 4
8
x 4
9
(D) x 4
LED
Cabinet
1
(L) x 4
(K) x 4
(L)
(K)
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
15
Figure 21
4. After the bottom row of cabinets are installed, it is a good
idea to install the far left column of cabinets to check that
everything is square and straight.
5. Using levels, occasionally check the level and plumb of the
cabinets installed on the mounts and adjust as necessary
using:
• the adjustment screws installed in Step 4 of the
Checking Placement and Alignment section, and/or
• the mounting buttons (for slight adjustments only)
(See Figure 21)
6. Only AFTER the housings have been adjusted as
necessary and are in the final, required position cam
housings together following instructions included with LED
panels.
7. Install LED panels into cabinets following instructions
included with cabinets and LED panels.
Fastener Installation Methods
IMPORTANT ! : See Table 1 for appropriate hardware
and pilot hole sizes for various wall types.
IMPORTANT ! : The expanse of the LED wall will most
likely mean that attachment of the wall mounts will not all
be in studs. The attachment method will most likely vary
throughout the installation, and more than one of the
various methods outlined here will most likely be used.
Wood Stud
1. Use one 5/16" x 2-1/2" hex flange head lag bolt (D) and one
5/16" washer (E) through product and into pilot hole. (See
Figure 22)
2. Repeat for remaining pilot holes.
Figure 22
Concrete or Concrete Block
1. Install one UX10X60R anchor (C) into each pilot hole using
a hammer, making sure that the anchor is flush with the wall.
(See Figure 23)
2. Use one 5/16" x 2-1/2" hex flange head lag bolt (D) and one
5/16" washer (E) through product into each anchor in wall.
(See Figure 23)
3. Repeat for remaining pilot holes.
Figure 23
Mounting
button
Mounting hole
5
(L) x 4
NOTE: Use 5/32"
ball end hex
key (J) for
adjustment of
mounting buttons
Just a tip - When installing in a recess it may
also be helpful to install the far right column. This
allows you to check for squareness and level
inside of the recess.
Just a tip - When doing the final install of
cabinets, after the bottom row start at the left
column and work to the right. Install one column at
a time, and then slide it out of the way to the left
before installing the next column.
1
2
(D)
(E)
1
2
(D)
(C)
(E)
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
16
Steel Stud
IMPORTANT ! : See Site Requirements for Steel Stud
Installation section before proceeding with Steel Studs
installation to ensure installation site meets requirements!
The drywall must have a minimum thickness of 1/2"!
1. Hold metal channel on anchor flat alongside plastic straps
and slide channel through hole. (See Figure 24)
Figure 24
2. Holding plastic straps on anchor, pull anchor away from wall
until channel rests flush behind wall making sure anchor
channel is positioned vertically on drywall, or steel stud (if
present). (See Figure 25)
3. Slide plastic cap on anchor towards wall until flange of cap
is flush with wall. (See Figure 25)
Figure 25
4. Snap off plastic straps on anchor at wall by pushing side to
side, snapping off straps level with flange of plastic cap.
(See Figure 26)
Figure 26
5. Line up anchor with attachment point.
6. Insert 1/4-20 x 1-3/4" Phillips pan head screw through 1/4"
washer, corresponding mounting hole in wall bracket and
into anchor, and tighten until flush against wall bracket. DO
NOT over tighten! (See Figure 27)
Figure 27
Drywall
Plastic straps
1
Plastic cap
Drywall
Anchor metal channel
3
Steel stud
(side view)
2
(if present)
Plastic straps
Drywall
Anchor metal channel
Plastic cap
4
Steel stud
(side view)
(if present)
Drywall
Anchor metal channel
Phillips
6
Steel stud
Washer
(side view)
Wall bracket
(if present)
screw
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
17
Site Requirements for Wood or Steel Stud Installation
Figure 28
FRONT
There must be a minimum of
1-7/8" (48mm) clearance
inside wall
16" or 24" (on center) Studs
If back side of wall is unfinished,
to a minimum of one stud left
drywall must be installed
and right of the stud(s) being used
to install the mount. Drywall must be
secured to studs with screws a
maximum of 12" (305mm) apart
down center of stud.
Steel Stud (2 x 4 / 25ga minimum)
Stud type and structural strength must conform to the North American
Specification for the Design of Cold-Formed Steel Structural Members.
(Both Sides of Stud)
[362 S 125 18, C-Shaped, S-Stud Section]
Plywood
3/4" minimum thickness
plywood covered
with drywall having
maximum thickness of 5/8"
5/8" maximum
drywall thickness
Stud
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
18
DIMENSIONS
SHOWN WITH PHILIPS BDL SERIES LED PANELS
TIL1X2PH
DIMENSIONS: INCHES
MILLIMETERS
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
19
DIMENSIONS -- cont’d
SHOWN WITH PHILIPS BDL SERIES LED PANELS
TIL1X3PH
DIMENSIONS: INCHES
MILLIMETERS
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
20
DIMENSIONS -- cont’d
TIL1X4PH
SHOWN WITH PHILIPS BDL SERIES LED PANELS
DIMENSIONS: INCHES
MILLIMETERS
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
21
DIMENSIONS -- cont’d
SHOWN WITH PHILIPS BDL SERIES LED PANELS
TIL1X5PH
DIMENSIONS: INCHES
MILLIMETERS
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
22
DIMENSIONS -- cont’d
TIL4X4PH Configuration
DIMENSIONS: INCHES
MILLIMETERS
Installation Instructions TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1
23
DIMENSIONS -- cont’d
TIL5X5PH Configuration
DIMENSIONS: INCHES
MILLIMETERS
TIL1X2PH / TIL1X3PH / TIL1X4PH / TIL1X5PH / TILVAB1 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-00003228 Rev00
2020 Legrand | AV
www.legrandav.com
10/2020