Chief XSM1U User Manual
Displayed below is the user manual for XSM1U by Chief which is a product in the TV Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
XTM1U
XSM1U
FUSION EXTRA LARGE HEIGHT ADJUST
FLAT PANEL MOUNTS
XSM1U/XTM1U
XSM1U/XTM1U Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all parts are properly
assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of all
components located on the XSM1U/XTM1U does not exceed
250 lbs (113.4 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! :
The XSM1U/XTM1U mounts are designed to
be mounted to:
• a bare concrete wall with a minimum thickness of 8"
(203mm);
• a bare 8" x 8" x 16" (203mm x 203mm x 406mm)
concrete block wall; or
• wood studs spaced 24" or 32" (610mm or 813mm) on
center with a maximum drywall covering of 5/8".
NOTE: The XSM1U/XTM1U extra large height adjust mounts
may be used with the UL Listed FCAV1U Fusion pull-
out accessory.
--SAVE THESE INSTRUCTIONS--
Installation Instructions XSM1U/XTM1U
3
DIMENSIONS
2°
1°
0
DETAIL A
SCALE 1 : 1.5
D
B
BACKWARDS ANGLE COMPENSATION SETTINGS
A
DETAIL D
SCALE 1 : 1.5
DETAIL B
SCALE 1 : 1.5
XSM1U
1066.8
42.00 1085.9
42.75
2.25
57.2
666.8
26.25
3.75
95.3
7.00
177.8
1. MAXIMUM MOUNTING PATTERN IS 38.7" (982 mm) WITHOUT REVERSING UPRIGHTS
2. MAXIMUM MOUNTING PATTERN IS 42.1" (1070 mm) WITH REVERSING UPRIGHTS
3. FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK
ENGAGEMENT IS .75" (19 mm)
RAILS CAN BE SLID LEFT OR RIGHT FOR OFFSET
3.00
8.6
37.4
31.50
609.6
MINIMUM UPRIGHT SPACING
6.00
1.47 24.00
152.4
17.00
431.8
16.00
406.4
8.00
203.2
4.75
120.7
76.2
1.82
800.0
46.2
0.34
1.83
46.6
TYP.
1.48
37.5
8.7
0.34
23.62
600.0
12.5
0.49
TYP.
11.81
300.0
DIMENSIONS: [INCHES]
MILLIMETERS
XSM1U
XSM1U/XTM1U Installation Instructions
4
DIMENSIONS--continued
31.00
787.5
11.81
300.0
600.0
23.62
8.7
0.34
TYP.
0.49
12.5
1.48
37.5
TYP.
12°
24.07
611.3
MAXIMUM MOUNTING PATTERN IS 36.7" (932 mm) WITHOUT REVERSING UPRIGHTS
1.
MAXIMUM MOUNTING PATTERN IS 42.1" (1070 mm) WITH REVERSING UPRIGHTS2.
FOR RECESSED APPLICATIONS, MINIMUM VERTICAL LIFT FOR HOOK3.
ENGAGEMENT IS .75" (19 mm)
RAILS CAN BE SLID LEFT OR RIGHT
FOR OFFSET
215.9
3.00
76.2
0.34
8.6
406.4
16.00
622.3
24.50
52.0
2.05
77.5
1.82
46.2
3.05
431.8
17.00
120.7
4.75
MINIMUM WALL UPRIGHT SPACING
609.6
24.00
216.9
8.5 8.50
6.00
152.4
42.75
1085.9
1066.8
42.00
2.5
63.1
7.00
177.8
DIMENSIONS: [INCHES]
MILLIMETERS
XTM1U
Installation Instructions XSM1U/XTM1U
5
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
XSM1U/XTM1U Installation Instructions
6
TOOLS REQUIRED FOR INSTALLATION
PARTS
7/32" (5.5mm) Wood Stud
#2 3/8" (9.5mm) Concrete
1/8" (included) 3/16" x 10"
(included)
5/32" (included)
C (4)
E (4)
A (4) B (4) D (4)
F (4) G (8) H (4)
(XSM1U Only)
[Interface brackets]
Universal Hardware Kit
[Nesting [Universal
Wall Mounting Hardware Kit
J (4)
5/16 x 2-1/2"
K (4)
UX10x60mm
L (4)
[Slotted
washer]
U (4)
[Wall cover]
XSM1 Mount Hardware Kit
M (1)
1/8"
N (1)
3/16"
Q (4)
1/4-20 x 3/4"
P (2)
3/8-16 x 3/4"
XTM1 Mount Hardware Kit
M (1)
1/8"
N (1)
3/16"
Q (4)
1/4-20 x 3/4"
P (2)
3/8-16 x 3/4"
S (2)
1/4-20 x 1"
T (2)
1/4-20
V (1) W (1)
[left] [right] X (1) Y (1)
[left] [right]
(XTM1U Only)
[Interface brackets]
Z (1)
[XSM1U / XTM1U
mount]
OR
spacer]
M6 x 12mm M6 x 20mm M6 x 25mm M8 x 12mm
M8 x 20mm M8 x 30mm washer]
R (2)
[Pull knob]
[Included in hardware box] [Included in hardware box]
[Included in hardware box]
MM (1)
5/32"
Installation Instructions XSM1U/XTM1U
7
INSTALLATION
The XSM1U/XTM1U mounts are designed to be mounted to:
• a bare concrete wall with a minimum thickness of 8"
(203mm);
• a bare 8" x 8" x 16" (203mm x 203mm x 406mm)
concrete block wall; or
• wood studs spaced 24" or 32" (610mm or 813mm) on
center with a maximum drywall covering of 5/8".
The XTM1U has brackets which allow the TV to be tilted. The
XSM1U has static brackets which keep the TV in an upright
position.
Locate Mounting Site
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! It is the installers responsibility
to make certain the structure to which the mount is being
attached is capable of supporting five times the combined
weight of all components located on the mount, not to exceed
250 lbs (113.4 kg).
NOTE: Proceed to either the Installing to a Wood Stud Wall
section or the Installing to a Concrete Wall section.
Installing to a Wood Stud Wall
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 24" (610mm). Do not place
mounting brackets closer together than 24" (610mm). When
attaching to a wall containing studs located 16" on center,
space the uprights 32" (813mm) apart.
1. Determine the center of the TV screen, and where it should
be located on the wall.
2. Locate the closest stud to the left and right of the selected
location.
NOTE: If the screen area lies over a stud, use that stud and the
stud to either the left or right of it.
3. Line up the notches on mount (Z) with center of screen
marking to determine vertical center. (See Figure 1)
4. Measure up 8" (203mm) from the center point to mark
location of the upper mounting slots.
5. Using a level, mark the wall on each stud to attach the
mount through the upper mounting slots. (See Figure 2)
6. Drill one 7/32" (5.5mm) pilot hole in each stud.
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (J) into
pilot holes but do not tighten to wall.
8. Hang mount (Z), aligning upper mounting slots over lag
bolts and adjust side-to-side for proper location.
9. Place one slotted washer (L) over each flanged lag bolt.
(See Figure 2)
10. Tighten lag bolts to secure mount (Z) to wall at upper
mounting slots.
11. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 2)
Figure 1
12. Drill 7/32" (5.5mm) pilot holes at markings for lower
mounting holes. (See Figure 2)
13. Use two 5/16 x 2-1/2" flanged lag bolts (J) and two 5/16"
slotted washers (L) to attach the mount to the wall through
the lower mounting holes. (See Figure 2)
14. Slide rails to approximate center of screen location.
15. Proceed to Locking Rails section.
Figure 2
Center of screen
8"
Vertical center
of mount
(203.2mm)
11 12
56
7
10
(J) x 2
(Z)
9
(L) x 4
13
(J) x 2
13
XSM1U/XTM1U Installation Instructions
8
Installing to a Concrete Wall
CAUTION: MINIMUM HORIZONTAL DISTANCE
BETWEEN WALL BRACKETS IS 24" (610mm). Do not place
mounting brackets closer together than 24" (610mm).
1. Determine the center of the TV screen, and where it should
be located on the wall.
2. Line up the notches on mount (Z) with center of screen
marking to determine vertical center. (See Figure 1)
3. Measure up 8" (203.2mm) from the center point to mark
location of the upper mounting slots. (See Figure 1)
4. Using a level, mark the wall through both upper mounting
slots. (See Figure 3)
Figure 3
5. Drill one 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot hole at each
marking.
6. Install an anchor (K) into each pilot hole using a hammer,
making sure that the anchor is flush with the wall.
7. Partially install two 5/16 x 2-1/2" flanged lag bolts (J) into
pilot holes but do not tighten to wall.
8. Hang mount (Z), aligning upper mounting slots over lag
bolts and adjust side-to-side for proper location.
9. Place one slotted washer (L) over each flanged lag bolt.
(See Figure 3)
10. Tighten lag bolts to secure mount (Z) to wall at upper
mounting slots.
11. Mark the attachment points for the lower mounting slots,
making sure the attachment points are located on the studs.
(See Figure 3)
12. Drill 3/8" x 3-1/2" (9.5mm x 88.9mm) pilot holes at markings
for lower mounting holes. (See Figure 3)
13. Use two 5/16 x 2-1/2" flanged lag bolts (J) and two 5/16"
slotted washers (L) to attach the mount to the wall through
the lower mounting holes. (See Figure 3)
14. Slide rails to approximate center of screen location.
Locking Rails (Optional)
1. Lock rails into place using two 1/4-20 x 3/4" set screws (Q)
on mount upright (Z) and the 1/8" hex key (M). (See Figure 4)
2. Repeat for remaining mount upright.
NOTE: To easily install upper set screw against upper rail,
place set screw (Q) onto hex key (M), and feed up into
hole while turning to tighten.
Figure 4
11
5
6
4
12
x 4
(K) x 4
10 710
(J) x 2
(L) x 4
9
13
13
(J) x 2
(Z)
(Q) x 4
1
(M)
(M)
Installation Instructions XSM1U/XTM1U
9
Attaching Interface Brackets to Screen
1. Align the center of the bracket (V and W or X and Y) with
center of screen. (See Figure 5)
NOTE: The diamond-shape holes in the bracket correspond to
the center of the mount.
Figure 5
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.
2. Select correct screws, nesting spacers (if necessary) and
universal washers from the hardware bag (A-H) and attach
brackets to back of screen. (See Figure 5)
NOTE: The nesting spacers (G) may be used separately, or put
two together in different configurations to create
different size spacers. (See Figure 6)
Figure 6
Switching Interface Brackets (Optional)
If an installation situation makes adjusting the location of
interface brackets necessary, there are several options.
1. The wall brackets may be adjusted side to side at the point
of attachment. (See Figure 7)
2. The location of the left and right interface brackets (V and W
or X and Y) may be switched, with the knobs on the XTM1U
interface brackets (X and Y) facing the inside of the mount.
(See Figure 7)
Figure 7
Center of bracket
[Brackets V and W shown]
(G)
(H)
(A-F)
(Single) (Nested) (Stacked)
0.375
[9.5]
0.563
[14.3]
0.750
[19.1]
1
2
Knobs
[Brackets X and Y shown]
XSM1U/XTM1U Installation Instructions
10
3. If necessary, the tilt interface bracket knobs may be
switched to allow the interface brackets (X and Y) to be
reversed. (See Figure 8)
a. Remove display from mount.
b. Remove interface brackets from display.
c. Hold the right interface bracket horizontally, tightly
gripping it so that spacers do not move.
d. Remove the knob and screw.
e. Replace the knob and screw in the opposite order, with
the knob on the inside of the bracket.
f. Switch the right interface bracket to the left side of the
wall mount.
g. Repeat Steps 3c through 3f with the left interface
bracket.
Figure 8
Attaching Screen to Wall Mount
1. Attach wall covers (U) to top and bottom of both wall
brackets. (See Figure 9)
Figure 9
NOTE: NEVER place both interface brackets (V and W or X
and Y) to one side of the wall mount center line! (See
Figure 10)
NOTE: Do NOT allow both interface brackets (V and W or X
and Y) to be located on same side of wall bracket. (See
Figure 10)
Figure 10
3e
Knobs to outside
of brackets
[Brackets X and Y shown]
3d
(U) x 4
Both interface brackets must NEVER be located
to one side of the wall brackets!
NEVER place both interface brackets to one
side of the wall mount center line (CL)!
Center Line (CL)
[Brackets V and W shown]
Installation Instructions XSM1U/XTM1U
11
IMPORTANT ! : (XSM1U Only) Completely extend bottom of
interface brackets (by pulling downward) to set interface
brackets in SERVICE position before hanging on top rail. (See
Figure 11)
2. Hang screen onto the top rail of the mount (Z). (See Figure 12)
•XSM1U: Hang top hook of interface brackets (V and
W) onto the top rail of the mount (Z). (See Figure 12)
•XTM1U: Move latch on top of interface bracket to
OPEN position and hang top hook of interface brackets
(X and Y) onto the top rail of the mount (Z). (See
Figure 12)
NOTE: The screen initially installs into the "service mode" to
allow easy cable access.
3. Adjust screen and rails to desired viewing position, and
route cables between wall and rails.
CAUTION: PINCH POINTS! Keep fingers, hands and
cables out of pinch point areas.
4. Fasten bottom of screen to mount:
•XSM1U - Open latch by pushing bottom of interface
bracket up to OPEN position, latching interface
brackets to lower rail, and then push up from bottom of
interface bracket again until the interface bracket is in
CLOSED position. (See Figure 11) and (See Figure 12)
•XTM1U - Pull downward on the pull cords and swing
inward toward mount, latching interface brackets to
lower rail and fastening bottom of screen to the mount.
(See Figure 12)
Figure 11
5.
XTM1U Only:
Attach end of pull cord (a magnet) to mount so
it does not extend beyond bottom of screen. (See Figure 12)
Latch in
SERVICE
position
Latch in
OPEN
position
Latch in
CLOSED
position
Figure 12
2
Top
Hook
XSM1U XTM1U
Latch in
5
Pull
cords
4
4
4
4
2
OPEN
position
XSM1U/XTM1U Installation Instructions
12
OPTIONAL: Adding Pull Knob (XSM1U Only)
1.
If necessary due to height of tall screen, add pull knob (R) to
bottom of interface brackets (V and W) to allow easier
accessibility for adjustment purposes. (See Figure 13)
2. Adjust length of pull knob so it is not visible below screen.
(See Figure 13)
Figure 13
Adjustments
Horizontal Adjustment
1. The mount wall brackets may be adjusted side-to-side at
the point of attachment. (See Figure 14)
Figure 14
2. The screen may be adjusted along rails side to side.
NOTE: NEVER place both interface brackets (V and W or X
and Y) to one side of the wall mount center line! (See
Figure 10)
NOTE: Do NOT allow both interface brackets (V and W or X
and Y) to be located on same side of wall bracket. (See
Figure 10)
3. (XTM1U only) Move latch on top of interface brackets to
CLOSED position. (See Figure 16)
Roll/Height Adjustment of Wall Brackets
NOTE: The height adjust wall brackets allow adjustment of
+ 1/2" (12.7mm).
1. Turn to right (tighten) to raise side of screen. (See Figure 15)
2. Turn to left (loosen) to lower side of the screen.
Figure 15
(R)
(V or W)
1
2
3" (76.2mm) horizontal
1
adjustment possible
Raises screen
Lowers screen
1
2
(Screen not shown for clarity)
(N)
Installation Instructions XSM1U/XTM1U
13
Tilt (XTM1U Only)
The interface brackets (X and Y) allow from -5° to 12° tilt, and
can be locked at 0°, 6° and 12°.
1. Loosen the interface bracket knob.
2. Adjust tilt as required. (See Figure 16)
3. The tilt may be locked at 0°, 6° or 12° using one 1/4-20 x 1"
round head carriage bolt (S) and one 1/4-20 hex nut (T) per
interface bracket. (See Figure 16)
4. Tighten interface bracket knob as necessary.
Figure 16
Latch in
CLOSED
position
3
(T)
2
Lock at 12° tilt
Lock at 6° tilt
Lock at 0° tilt
Interface
bracket
knob
(S)
XSM1U/XTM1U Installation Instructions
14
Backwards Angle Compensation (XSM1U Only)
The XSM1U may be slightly adjusted to help compensate for
the forward tilt of a heavy screen.
NOTE: The interface brackets (V and W) ship in the 0° tilt
position. (See Figure 17)
1. With interface brackets in CLOSED position (See Figure
11), remove two fasteners holding tilt compensation in place
on each interface bracket (V and W). (See Figure 17)
2. Adjust interface bracket for -1° or -2° back tilt, as required.
(See Figure 17)
3. Tighten two fasteners (removed in Step 1). (See Figure 17)
Figure 17
(V and W)
3
1
Fasteners set at
-1° back tilt
Fasteners set at
-2° back tilt
Fasteners set at
0° back tilt
(Ships in this position)
Installation Instructions XSM1U/XTM1U
15
Locking Screen Interface Brackets (Optional)
1. Lock screen interface brackets onto mount rails using one
3/8-16 x 3/4" set screw (P) on each interface bracket. (See
Figure 18)
Figure 18
Locking Mount (Optional)
1. Add padlock (not included) to interface bracket to complete
security. (See Figure 19)
NOTE: The padlock maximum shackle diameter is 5/16"
(7.9 mm).
Figure 19
(XTM1U)
(XSM1U)
1
(P) x 2
1
(P) x 2
1
(XSM1U) Padlock shackle
- 5/16" (7.9mm)
maximum diameter:
1
Padlock shackle
- 5/16" (7.9mm)
maximum diameter:
(XTM1U)
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
XSM1U/XTM1U Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002635 Rev03
2016 Milestone AV Technologies
www.chiefmfg.com
01/16