Contour Design RollerMouse Free3 User Manual
Displayed below is the user manual for RollerMouse Free3 by Contour Design which is a product in the Mice category. This manual has pages.
Related Manuals
User Guide
RollerMouse Free3 user guide
Box contents
1. RollerMouse Free3
2. Two short keyboard risers
3. Two long keyboard risers
1
2 3
/1
RollerMouse Free3 user guide
RollerMouse functions
A. Rollerbar
B. Cursor speed LED
C. Copy
D. Paste
E. Back
F. Forward
G. Left-click
H. Right-click
I. Scroll wheel
J. “One Touch” double-click
For additional mouse features and specic
Mac settings, please download our driver
at www.contour-design.co.uk.
J
/2
RollerMouse Free3 user guide
Keyboard positioning
Before plugging in the unit, take a moment to check the height and angle of
your keyboard, and nd the arrangement that’s most comfortable for you.
Use the risers to achieve the correct angle and height regardless of the type
of keyboard you are using. The spacebar on your keyboard should come just
above your rollerbar. To achieve a proper ergonomic position, the front edge
of the keyboard should be as close to the rollerbar.
Balance Keyboard is designed specically for the RollerMouse Free3. The
keyboard sits level with the rollerbar and can be easily adjusted to a positive,
neutral, or negative tilt.
Positive tilt
Neutral tiltNegative tilt
/3
RollerMouse Free3 user guide /4
Inserting the keyboard risers
Fit the end of the riser into the slot on the back of the RollerMouse Free3.
Line up the grooves of the short and long risers and then press the
two parts together until you hear them snap into place.
2
2
2
3
3
2
Negative Tilt
Neutralt hævet
Neutralt adt
Positiv hældning
RollerMouse Free3 user guide
Connecting to a computer
Plug the RollerMouse Free3 USB cable into the computer’s USB
port. Allow your computer a few seconds to automatically install.
Using the rollerbar
The rollerbar provides two functions:
• Pressing down on the rollerbar performs a left click.
• Moving the rollerbar from side to side and up and down performs cursor
movement.
A
/5
RollerMouse Free3 user guide /6
B
J
Click force tension adjustment
You can adjust the amount of pressure required to perform a mouse click. Use
the click-force tension slider located under your RollerMouse Free3. Simply
slide it until you nd the tension that works best for you.
Changing the ‘Double’ click button to middle
To change button from a double click function to a middle button
function, hold buttons and for two seconds until LED lights ashes
to conrm. Repeating this process will revert back to double click function.
B
B J
RollerMouse Free3 user guide
B
/7
Change cursor speed
Press the Cursor Speed button to cycle through cursor speeds. There are
ten speed selections which range from slow (600 DPI) to fast (2800 DPI). Speed
can be identied by the LED lights as shown.
To see the current DPI level, press the Cursor Speed button once.
B
B
RollerMouse Free3 user guide
CD
B
E
/8
Operating system
RollerMouse Free3 has 3 modes. PC- mode , Mac-mode and HID-mode.
Use the following key commands to switch settings to best t your
operating system.
+ : PC Mode (Hold down the Cursor Speed and press Copy)
+ : Mac Mode (Hold down the Cursor Speed and press Paste)
+ : HID Mode (Hold down the Cursor Speed and press Back)
B
B
C
D
BE
Dierent mode settings
PC-Mode
MAC-Mode
HID-Mode
LED’s light up from
left to right. Windows
OS
Linux
LED’s light up from
right to left.
LED’s light up from both
sides towards the middle.
FCC Statement
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: “ before the certication/registration number only signies that the Industry Canada technical specications were met. This
product meets the applicable Industry Canada technical specications.
Le présent appareil est conforme aux CNR d’Industrie Canada applicable aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement
Warranty
If there is a functional defect due to faulty manufacturing, we will replace the product. This warranty does not cover damage that results from
misuse of the product.
Attention!
If you attempt to dismantle your RollerMouse, you will invalidate your warranty.
For more information please visit:
www.contour-design.co.uk
Kingsbury House
468 Church Lane
London, NW9 8UA
United Kingdom
Phone: +45 70 27 02 27
Email: info@contour-design.com
Tested to comply with FCC
and IC standards.