Dell PowerEdge R530 Owner's Manual
About your system
Performing initial system configuration
Pre-operating system management applications
Installing and removing system components
Troubleshooting your system
Using system diagnostics
- Dell Embedded System Diagnostics
Jumpers and connectors
Technical specifications
Getting help

DELL R530 User Manual

Displayed below is the user manual for R530 by DELL which is a product in the Servers category. This manual has pages.

Related Manuals

DELL R530 Manual

Dell PowerEdge R530

Owner's Manual

Regulatory Model: E29S Series

Regulatory Type: E29S001

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2014 - 11

Rev. A00

Contents

1 About your system................................................................................................ 8

Front-panel features and indicators.....................................................................................................8

LCD panel features..............................................................................................................................10

Home screen................................................................................................................................. 10

Setup menu.................................................................................................................................... 11

View menu......................................................................................................................................11

Hard-drive indicator patterns..............................................................................................................12

Back-panel features and indicators.................................................................................................... 13

NIC indicator codes.............................................................................................................................15

Power supply unit indicator codes..................................................................................................... 15

Power indicator codes for AC and DC redundant power supply unit.........................................15

Indicator codes for non-redundant power supply...................................................................... 18

Documentation matrix........................................................................................................................ 19

Quick Resource Locator (QRL)...........................................................................................................20

2 Performing initial system configuration ........................................................21

Setting up your system........................................................................................................................21

Setting up and configuring the iDRAC IP address .............................................................................21

Logging in to iDRAC............................................................................................................................ 21

Installing the operating system...........................................................................................................22

Managing your system remotely........................................................................................................ 22

Downloading and installing drivers and firmware............................................................................. 22

3 Pre-operating system management applications........................................24

Navigation keys................................................................................................................................... 24

About System Setup............................................................................................................................24

Entering System Setup.................................................................................................................. 25

System Setup Main Menu..............................................................................................................25

System BIOS screen...................................................................................................................... 25

System Information screen...........................................................................................................26

Memory Settings screen............................................................................................................... 26

Processor Settings screen.............................................................................................................27

SATA Settings screen.....................................................................................................................28

Boot Settings screen......................................................................................................................31

Network Settings screen............................................................................................................... 31

Integrated Devices screen details.................................................................................................32

Serial Communication screen...................................................................................................... 33

System Profile Settings screen......................................................................................................34

System Security Settings screen................................................................................................... 35

Miscellaneous Settings screen......................................................................................................37

About Boot Manager...........................................................................................................................38

Entering Boot Manager ................................................................................................................38

Boot Manager main menu............................................................................................................ 38

About Dell Lifecycle Controller.......................................................................................................... 38

Changing the boot order....................................................................................................................39

Choosing the system boot mode.......................................................................................................39

Assigning a system and setup password............................................................................................39

Using your system password to secure your system........................................................................40

Deleting or changing an existing system and/or setup password.................................................... 41

Operating with a setup password enabled.........................................................................................41

Embedded system management....................................................................................................... 42

iDRAC Settings utility.......................................................................................................................... 42

Entering the iDRAC Settings utility............................................................................................... 42

Changing the Thermal Settings.................................................................................................... 42

4 Installing and removing system components...............................................43

Safety instructions...............................................................................................................................43

Before working inside your system.................................................................................................... 43

After working inside your system....................................................................................................... 43

Recommended tools.......................................................................................................................... 44

Front bezel (optional)..........................................................................................................................44

Removing the front bezel............................................................................................................. 44

Installing the front bezel............................................................................................................... 45

Removing and installing the system cover........................................................................................ 45

Removing the system cover......................................................................................................... 46

Installing the system cover........................................................................................................... 46

Inside the system.................................................................................................................................47

Cooling shroud................................................................................................................................... 49

Removing the cooling shroud......................................................................................................49

Installing the cooling shroud.........................................................................................................51

System memory...................................................................................................................................51

General memory module installation guidelines.........................................................................53

Mode-specific guidelines..............................................................................................................53

Sample memory configurations................................................................................................... 54

Removing a memory module.......................................................................................................56

Installing memory modules.......................................................................................................... 58

Hard drives.......................................................................................................................................... 60

Removing a hot-swap hard drive.................................................................................................60

Installing a hot-swap hard drive....................................................................................................61

Removing a 3.5 inch hard-drive blank......................................................................................... 62

Installing a 3.5 inch hard-drive blank........................................................................................... 63

Removing a 2.5 inch hard drive from a 3.5 inch hard-drive adapter..........................................64

Installing a 2.5 inch hard drive into a 3.5 inch hard-drive adapter..............................................65

Removing a hard-drive adapter from a hard-drive carrier..........................................................65

Installing a hard-drive adapter into a hard-drive carrier............................................................. 66

Removing a hard drive from a hard-drive carrier........................................................................ 66

Installing a hard drive into a hard-drive carrier............................................................................ 67

Optical drive (optional)........................................................................................................................67

Removing the optical drive........................................................................................................... 67

Installing the optical drive.............................................................................................................68

Cooling fans........................................................................................................................................ 69

Removing a cooling fan................................................................................................................69

Installing a cooling fan...................................................................................................................71

Internal USB memory key (optional)...................................................................................................71

Replacing the internal USB key..................................................................................................... 71

Expansion cards and expansion-card riser (optional)........................................................................72

Expansion-card installation guidelines.........................................................................................73

Removing an expansion card from the system board.................................................................75

Installing an expansion card on the system board...................................................................... 76

Removing the (optional) expansion-card riser.............................................................................77

Installing the (optional) expansion-card riser...............................................................................78

Removing an expansion card from the expansion-card riser..................................................... 79

Installing an expansion card into the expansion-card riser.........................................................81

iDRAC ports card (optional)................................................................................................................82

Removing the iDRAC ports card...................................................................................................82

Installing the iDRAC ports card.....................................................................................................84

SD vFlash media card..........................................................................................................................84

Replacing an SD vFlash media card..............................................................................................84

Internal dual SD module..................................................................................................................... 85

Removing an internal SD card...................................................................................................... 85

Installing an internal SD card........................................................................................................86

Removing the internal dual SD module ...................................................................................... 87

Installing the internal dual SD module ........................................................................................ 89

Integrated storage controller card.....................................................................................................90

Removing the integrated storage controller card....................................................................... 90

Installing the integrated storage controller card......................................................................... 92

Processors........................................................................................................................................... 92

Removing a processor.................................................................................................................. 93

Installing a processor.................................................................................................................... 97

Power supplies..................................................................................................................................100

Hot Spare feature........................................................................................................................100

Removing the power supply unit blank..................................................................................... 100

Installing the power supply unit blank........................................................................................101

Removing an AC power supply unit........................................................................................... 101

Installing an AC power supply unit.............................................................................................102

Non-redundant AC power supply (cabled)................................................................................103

Wiring instructions for a DC power supply unit.........................................................................105

Removing a DC power supply unit.............................................................................................108

Installing a DC power supply unit...............................................................................................109

Power interposer board.................................................................................................................... 110

Removing the power interposer board...................................................................................... 110

Installing the power interposer board.........................................................................................112

System battery................................................................................................................................... 112

Replacing the system battery...................................................................................................... 112

Hard-Drive Backplane....................................................................................................................... 114

Removing the hard-drive backplane.......................................................................................... 114

Installing the hard-drive backplane............................................................................................ 116

Control panel and I/O module..........................................................................................................117

Removing the control-panel board............................................................................................ 117

Installing the control-panel board..............................................................................................118

Removing the control panel........................................................................................................119

Installing the control panel.........................................................................................................120

System board..................................................................................................................................... 121

Removing the system board........................................................................................................121

Installing the system board......................................................................................................... 123

Restoring the Service Tag using Easy Restore............................................................................125

Entering the system Service Tag using System Setup................................................................125

Trusted Platform Module..................................................................................................................126

Installing the Trusted Platform Module .....................................................................................126

Re-enabling the TPM for BitLocker users...................................................................................127

Re-enabling the TPM for TXT users............................................................................................127

5 Troubleshooting your system........................................................................ 128

Safety first—for you and your system...............................................................................................128

Troubleshooting system startup failure........................................................................................... 128

Troubleshooting external connections............................................................................................128

Troubleshooting the video subsystem.............................................................................................128

Troubleshooting a USB device......................................................................................................... 128

Troubleshooting a serial I/O device................................................................................................. 129

Troubleshooting a NIC......................................................................................................................129

Troubleshooting a wet system......................................................................................................... 130

Troubleshooting a damaged system................................................................................................ 131

Troubleshooting the system battery.................................................................................................131

Troubleshooting power supply units................................................................................................132

Power source problems....................................................................................................................132

Power supply unit problems.............................................................................................................132

Troubleshooting cooling problems..................................................................................................133

Troubleshooting cooling fans...........................................................................................................133

Troubleshooting system memory.................................................................................................... 134

Troubleshooting an internal USB key...............................................................................................135

Troubleshooting an SD card.............................................................................................................135

Troubleshooting an optical drive..................................................................................................... 136

Troubleshooting a hard drive............................................................................................................137

Troubleshooting a storage controller...............................................................................................137

Troubleshooting expansion cards....................................................................................................138

Troubleshooting processors.............................................................................................................139

System messages.............................................................................................................................. 139

Warning messages.......................................................................................................................139

Diagnostic messages...................................................................................................................139

Alert messages............................................................................................................................ 140

6 Using system diagnostics................................................................................141

Dell Embedded System Diagnostics.................................................................................................141

When to use the Embedded System Diagnostics...................................................................... 141

Running the Embedded System Diagnostics............................................................................. 141

System diagnostic controls.........................................................................................................142

7 Jumpers and connectors................................................................................ 143

System board jumper settings.......................................................................................................... 143

System board connectors.................................................................................................................144

Disabling a forgotten password........................................................................................................145

8 Technical specifications..................................................................................147

9 Getting help.......................................................................................................153

Contacting Dell..................................................................................................................................153

Locating your system Service Tag....................................................................................................153

Documentation feedback................................................................................................................. 153

Quick Resource Locator (QRL).........................................................................................................153

About your system

The Dell PowerEdge R530 is a rack server that supports up to two processors based on the Intel E5-2600

v3 product family, up to 12 DIMMs, and up to eight drive bays for hard drives/ SSDs.

The PowerEdge R530 system is available in the following configurations:

• Redundant power supply configuration

• Non-redundant power supply configuration

Front-panel features and indicators

Figure 1. Front-panel features and indicators

Item Indicator, Button, or

Connector Icon Description

1 Power-on indicator,

power button

The power-on indicator lights when the system is

powered on. The power button controls the power

supply output to the system.

NOTE: On ACPI-compliant operating systems,

turning off the system using the power button

causes the system to perform a graceful

shutdown before power to the system is

turned off.

2 NMI button Used to troubleshoot software and device driver

errors when using certain operating systems. This

Item Indicator, Button, or

Connector Icon Description

button can be pressed using the end of a paper

clip.

Use this button only if directed to do so by

qualified support personnel or by the operating

system's documentation.

3 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pushed, the LCD panel on the front and the system

status indicator on the back flash blue until one of

the buttons is pushed again.

Press to toggle the system ID ON and OFF. If the

system hangs during POST, press and hold the

system ID button for more than five seconds to

enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC

setup) press and hold for more than 15 seconds.

4 Video connector Connects a VGA display to the system.

5 LCD menu buttons Allows you to navigate the control panel LCD

menu.

6 LCD panel Displays system ID, status information, and system

error messages. See LCD panel features.

7 USB management port/

iDRAC Direct

Allows you to connect USB devices to the system

or provides access to the iDRAC Direct features.

For more information, see the Integrated Dell

Remote Access Controller User’s Guide at

dell.com/esmmanuals. The USB management port

is USB 2.0-compliant.

8 USB connector Allows you to connect USB devices to the system.

The ports are USB 2.0 compliant.

9 Information tag A slide-out label panel, which allows you to record

system information, such as Service Tag, NIC

addresses, MAC address, and so on, for your

reference.

10 Optical drive (optional) One optional SATA DVD-ROM drive or DVD+/-RW

drive.

NOTE: DVD devices are data only.

11 Hard drives/SSDs bay Up to eight 2.5 inch or 3.5 inch hot-swappable

hard drives/SSDs.

LCD panel features

The system's LCD panel provides system information and status and error messages to indicate if the

system is operating correctly or if the system needs attention. For more information on error messages,

see the Dell Event and Error Messages Reference Guide at dell.com/esmmanuals.

• The LCD backlight lights blue during normal operating conditions.

• When the system needs attention, the LCD lights amber, and displays an error code followed by

descriptive text.

NOTE: If the system is connected to a power source and an error is detected, the LCD lights

amber regardless of whether the system is turned on or off.

• The LCD backlight turns OFF when the system is in standby mode and can be turned on by pressing

either the Select, Left, or Right button on the LCD panel.

• The LCD backlight remains OFF if LCD messaging is turned off through the iDRAC utility, the LCD

panel, or other tools.

Figure 2. LCD panel features

Item Button Description

1 Left Moves the cursor back in one-step increments.

2 Select Selects the menu item highlighted by the cursor.

3 Right Moves the cursor forward in one-step increments.

During message scrolling:

• Press once to increase scrolling speed

• Press again to stop

• Press again to return to the default scrolling speed

• Press again to repeat the cycle

Home screen

The Home screen displays user-configurable information about the system. This screen is displayed

during normal system operation when there are no status messages or errors. When the system is in

standby mode, the LCD backlight turns off after five minutes of inactivity if there are no error messages.

Press one of the three navigation buttons (Select, Left, or Right) to view the Home screen.

To navigate to the Home screen from another menu, follow the steps below.

1. Press and hold the up arrow until the Home icon is displayed.

2. Select the Home icon.

3. From the Home screen, press the Select button to enter the main menu.

Setup menu

NOTE: When you select an option in the Setup menu, you must confirm the option before

proceeding to the next action.

Option Description

iDRAC Select DHCP or Static IP to configure the network mode. If Static IP is selected,

the available fields are IP, Subnet (Sub), and Gateway (Gtw). Select Setup DNS to

enable DNS and to view domain addresses. Two separate DNS entries are available.

Set error Select SEL to display LCD error messages in a format that matches the IPMI

description in the SEL. This is useful when trying to match an LCD message with an

SEL entry.

Select Simple to display LCD error messages in a simplified user-friendly

description. For more information on error messages, see the Dell Event and Error

Messages Reference Guide at dell.com/esmmanuals.

Set home Select the default information to be displayed on the LCD Home screen. See View

menu to see the options and option items that can be set as the default on the

Home screen.

View menu

NOTE: When you select an option in the View menu, you must confirm the option before

proceeding to the next action.

Option Description

iDRAC IP Displays the IPv4 or IPv6 addresses for iDRAC8. Addresses include DNS (Primary

and Secondary), Gateway, IP, and Subnet (IPv6 does not have Subnet).

MAC Displays the MAC addresses for iDRAC, iSCSI, or Network devices.

Name Displays the name of the Host, Model, or User String for the system.

Number Displays the Asset tag or the Service tag for the system.

Power Displays the power output of the system in BTU/hr or Watts. The display format can

be configured in the Set home submenu of the Setup menu.

Temperature Displays the temperature of the system in Celsius or Fahrenheit. The display format

can be configured in the Set home submenu of the Setup menu.

Hard-drive indicator patterns

Figure 3. Hard-drive indicators

1. hard-drive activity indicator 2. hard-drive status indicator

3. hard drive

NOTE: If the hard drive is in Advanced Host Controller Interface (AHCI) mode, the status indicator

(on the right side) does not function and remains OFF.

Drive-status indicator

pattern (RAID only) Condition

Blinks green two times per

second

Identifying the drive or preparing for removal.

OFF Drive ready for insertion or removal.

NOTE: The drive status indicator remains OFF until all hard drives are

initialized after the system is turned on. Drives are not ready for

insertion or removal during this time.

Blinks green, amber, and

off

Predicted drive failure

Blinks amber four times per

second

Drive failed

Blinks green slowly Drive rebuilding

Steady green Drive online

Drive-status indicator

pattern (RAID only) Condition

Blinks green three seconds,

amber three seconds, and

OFF six seconds

Rebuild aborted

Back-panel features and indicators

Figure 4. Back-panel features and indicators for a non-redundant power supply unit chassis and a redundant

power supply unit chassis

Item Indicator, button, or

connector Icon Description

1 Serial connector Connects a serial device to the system.

2 Ethernet connectors (2) Integrated 10/100/1000 Mbps NIC connector

3 vFlash media card slot

(Optional)

Allows you to insert a vFlash media card.

4 iDRAC port (Optional) Dedicated management port for the iDRAC Ports

Card.

5 Full Height PCIe

expansion card slots (2)

PCIe cards located on the optional expansion-card

riser

6 Redundant Power

Supply Unit AC 495 W EPP, 750 W EPP or

1100 W EPP

DC 750 W

Item Indicator, button, or

connector Icon Description

7 Non-Redundant Power

Supply Unit

450 W

8 Half Height PCIe

expansion card slots (5)

Allows you to connect PCIe expansion cards.

9 Ethernet connectors (2) Integrated 10/100/1000 Mbps NIC connector

10 System identification

connector

Connects the optional system status indicator

assembly through the optional cable management

arm.

11 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pushed, the LCD panel on the front and the system

status indicator on the back blink until one of the

buttons is pushed again.

Press to toggle the system ID on and off. If the

system hangs during POST, press and hold the

system ID button for more than five seconds to

enter BIOS progress mode.

To reset the iDRAC (if not disabled in System

Setup) press and hold for more than 15 seconds.

12 USB connector Connects USB devices to the system. This port is

USB 3.0-compliant.

13 USB connector Connects USB devices to the system. This port is

USB 2.0-compliant.

14 Video connector Connects a VGA display to the system.

NIC indicator codes

Figure 5. NIC indicators

1. link indicator 2. activity indicator

Convention Indicator pattern Description

A Link and activity indicators

are OFF

The NIC is not connected to the network.

B Link indicator is green The NIC is connected to a valid network at its maximum

port speed (1 Gbps).

C Link indicator is yellow The NIC is connected to a valid network at less than its

maximum port speed.

D Activity indicator is blinking

green

Network data is being sent or received.

Power supply unit indicator codes

Power indicator codes for AC and DC redundant power supply unit

Each AC power supply unit (PSU) has an illuminated translucent handle and each DC PSU (when

available) has an LED that serves as an indicator to show whether power is present or a power fault has

occurred.

Figure 6. AC power supply unit status indicator

Convention Power indicator

pattern Condition

A Green The handle indicator lights green indicating that a valid power

source is connected to the PSU and that the PSU is operational.

B Flashing green When updating the firmware of thePSU, the PSU handle flashes

green.

CAUTION:

Do not disconnect the power cord or unplug the PSU when

updating firmware. If firmware update is interrupted, the PSUs will

not function. You must roll back the power supply firmware by using

Life cycle controller. See Dell Lifecycle Controller User’s Guide at

dell.com/esmmanuals

C Flashes green

and turns off

When hot-adding a PSU, the handle of the new power supply unit

flashes green five times at 4 Hz rate and turns off. This indicates that

the new PSU is mismatched with the PSU that is installed (in terms of

efficiency, feature set, health status, and supported voltage). Use a

PSU that matches the capacity of the PSU that is installed.

NOTE: For AC power supplies, use only PSUs with the Extended

Power Performance (EPP) label on the back. Mixing PSUs from

previous generations of servers can result in a PSU mismatch

condition or failure to power on.

D Flashing amber Indicates a problem with the power supply unit.

Convention Power indicator

pattern Condition

CAUTION: When correcting a PSU mismatch, replace only the

PSU with the flashing indicator. Swapping the opposite power

supply unit to make a matched pair can result in an error

condition and unexpected system shutdown. To change from

a High Output configuration to a Low Output configuration or

vice versa, you must power down the system.

CAUTION: AC power supplies support both 220 V and 110 V

input voltages with the exception of Titanium power supplies,

which support only 220 V. When two identical power supplies

receive different input voltages, they can output different

wattages, and trigger a mismatch.

CAUTION: If two power supplies are used, they must be of the

same type and have the same maximum output power.

CAUTION: Combining AC and DC power supplies is not

supported and triggers a mismatch.

E Not lit Power is not connected.

Figure 7. DC power supply unit status indicator

Convention Power indicator

pattern Condition

A Green The handle/LED indicator lights green indicating that a valid power

source is connected to the PSU and that the PSU is operational.

B Flashing green When hot-adding a PSU, the handle of the new power supply unit

flashes green five times at 4 Hz rate and turns off. This indicates

that the new PSU is mismatched with the PSU that is installed (in

terms of efficiency, feature set, health status, and supported

voltage). Use a PSU that matches the capacity of the PSU that is

installed.

C Flashing amber Indicates a problem with the PSU.

CAUTION: When correcting a PSU mismatch, replace only

the PSU with the flashing indicator. Swapping the opposite

PSU to make a matched pair can result in an error condition

and unexpected system shutdown. To change from a High

Output configuration to a Low Output configuration or vice

versa, you must power down the system.

CAUTION: If two power supplies are used, they must be of

the same type and have the same maximum output power.

CAUTION: Combining AC and DC power supplies is not

supported and triggers a mismatch.

D Not lit Power is not connected.

Indicator codes for non-redundant power supply

Press the self-diagnostic button to perform a quick health check on the non-redundant power supply of

the system.

Figure 8. Non-redundant AC power supply status indicator and self-diagnostic button

1. self-diagnostic button 2. AC power supply status indicator

Diagnostic Indicator Pattern Description

Not lit Power is not connected or power supply is faulty.

Green A valid power source is connected to the power supply and

the power supply is operational.

Documentation matrix

The documentation matrix provides information on documents that you can refer to for setting up and

managing your system.

To... Refer to...

Install your system into a rack Rack documentation included with your rack

solution

Set up your system and know the system technical

specifications

Getting Started With Your System that shipped with

your system or see dell.com/poweredgemanuals

Install the operating system Operating system documentation at dell.com/

operatingsystemmanuals

Get an overview of the Dell Systems Management

offerings

Dell OpenManage Systems Management Overview

Guide at dell.com/openmanagemanuals

Configure and log in to iDRAC, set up managed

and management system, know the iDRAC

features and troubleshoot using iDRAC

Integrated Dell Remote Access Controller User's

Guide at dell.com/esmmanuals

Know about the RACADM subcommands and

supported RACADM interfaces

RACADM Command Line Reference Guide for

iDRAC and CMC at dell.com/esmmanuals

Launch, enable and disable Lifecycle Controller,

know the features, use and troubleshoot Lifecycle

Controller

Dell Lifecycle Controller User’s Guide at dell.com/

esmmanuals

Use Lifecycle Controller Remote Services Dell Lifecycle Controller Remote Services Quick

Start Guide at dell.com/esmmanuals

Set up, use, and troubleshoot OpenManage Server

Administrator

Dell OpenManage Server Administrator User’s

Guide at dell.com/openmanagemanuals

Install, use and troubleshoot OpenManage

Essentials

Dell OpenManage Essentials User’s Guide at

dell.com/openmanagemanuals

Know the features of the storage controller cards,

deploy the cards, and manage the storage

subsystem

Storage controller documentation at dell.com/

storagecontrollermanuals

Check the event and error messages generated by

the system firmware and agents that monitor

system components

Dell Event and Error Messages Reference Guide at

dell.com/esmmanuals

Quick Resource Locator (QRL)

Use the Quick Resource Locator (QRL) to get immediate access to system information and how-to

videos. This can be done by visiting www.dell.com/QRL or by using your smartphone or tablet and a

model specific Quick Resource (QR) code located on your Dell PowerEdge system. To try out the QR

code, scan the following image.

Performing initial system configuration

After you receive your PowerEdge system, you must set up your system, install the operating system if it

is not pre-installed, and set up and configure the system iDRAC IP address.

Setting up your system

1. Unpack the server.

2. Install the server into the rack. For more information on installing the server into the rack, see your

system Rack Installation Placemat at dell.com/poweredgemanuals.

3. Connect the peripherals to the system.

4. Connect the system to its electrical outlet.

5. Turn the system on by pressing the power button or using iDRAC.

6. Turn on the attached peripherals.

Setting up and configuring the iDRAC IP address

You can set up the Integrated Dell Remote Access Controller (iDRAC) IP address by using one of the

following interfaces:

• iDRAC Settings utility

• Lifecycle Controller

• Dell OpenManage Deployment Toolkit

• Server LCD panel

You can configure iDRAC IP address by using the following interfaces:

• iDRAC Web interface. For more information, see the Integrated Dell Remote Access Controller User's

Guide.

• Remote Access Controller ADMin (RACADM). For more information, see the RACADM Command Line

Interface Reference Guide and the Integrated Dell Remote Access Controller User's Guide.

• Remote Services that includes Web Services Management (WS-Man). For more information, see the

Lifecycle Controller Remote Services Quick Start Guide.

For more information on setting up and configuring iDRAC, see the Integrated Dell Remote Access

Controller User's Guide at dell.com/esmmanuals.

Logging in to iDRAC

You can log in to iDRAC as an iDRAC local user, a Microsoft Active Directory user, or a Lightweight

Directory Access Protocol (LDAP) user. You can also log in by using Single Sign-On or a Smart Card. The

default user name is root and password is calvin. For more information on logging in to iDRAC and

iDRAC licenses, see the Integrated Dell Remote Access Controller User's Guide at dell.com/esmmanuals.

You can also access iDRAC using RACADM. For more information, see the RACADM Command Line

Interface Reference Guide and the Integrated Dell Remote Access Controller User's Guide available at

dell.com/esmmanuals.

Installing the operating system

If the server is shipped without an operating system, install the supported operating system on the server

by using one of the following methods:

• Dell Systems Management Tools and Documentation media. See the operating system

documentation at dell.com/operatingsystemmanuals.

• Dell Lifecycle Controller. See the Lifecycle Controller documentation at dell.com/esmmanuals.

• Dell OpenManage Deployment Toolkit. See the OpenManage documentation at dell.com/

openmanagemanuals.

For information on the list of operating systems supported on your system, see the operating systems

support matrix at dell.com/ossupport.

Managing your system remotely

To perform out-of-band systems management using iDRAC, you must configure iDRAC for remote

accessibility, set up the management station and managed system, and configure the supported Web

browsers. For more information, see the Integrated Dell Remote Access Controller User’s Guide at

dell.com/esmmanuals.

You can also remotely monitor and manage the server by using the Dell OpenManage Server

Administrator (OMSA) software and OpenManage Essentials (OME) systems management console. For

more information, see dell.com/openmanagemanuals.

Downloading and installing drivers and firmware

It is recommended that you download and install the latest BIOS, drivers, and systems management

firmware on your system.

Prerequisites

Ensure that you clear the web browser cache.

Steps

1. Go to dell.com/support/drivers.

2. In the Product Selection section, enter the Service Tag of your system in the Service Tag or Express

Service Code field.

NOTE: If you do not have the Service Tag, select Automatically detect my Service Tag for me

to allow the system to automatically detect your Service Tag, or select Choose from a list of all

Dell products to select your product from the Product Selection page.

3. Click Get drivers and downloads.

The drivers that are applicable to your selection are displayed.

4. Download the drivers you require to a diskette drive, USB drive, CD, or DVD.

Pre-operating system management

applications

The pre-operating system management applications for your PowerEdge system help you manage

different settings and features of your system without booting to the operating system.

Your PowerEdge system has the following pre-operating system management applications:

• System Setup

• Boot Manager

• Dell Lifecycle Controller

Navigation keys

The navigation keys can help you access the pre-operating system management applications.

Key Description

<Page Up> Moves to the previous screen.

<Page

Down>

Moves to the next screen.

Up arrow Moves to the previous field.

Down

arrow

Moves to the next field.

<Enter> Enables you to type a value in the selected field (if applicable) or follow the link in the field.

Spacebar Expands or collapses a drop-down list, if applicable.

<Tab> Moves to the next focus area.

NOTE: This feature is applicable for the standard graphical browser only.

<Esc> Moves to the previous page until you view the main screen. Pressing <Esc> in the main

screen exits System BIOS/iDRAC Settings/Device Settings/Service Tag Settings and

proceeds with system boot.

<F1> Displays the System Setup help.

About System Setup

Using System Setup, you can configure the BIOS settings, iDRAC settings, and device settings of your

system.

You can access System Setup in two ways:

• Standard Graphical Browser — This is enabled by default.

• Text Browser — This is enabled using Console Redirection.

NOTE: By default, help text for the selected field is displayed in the graphical browser. To view the

help text in the text browser, press <F1>.

Entering System Setup

1. Turn on or restart your system.

2. Press <F2> immediately after you see the following message:

<F2> = System Setup

If your operating system begins to load before you press <F2>, allow the system to finish booting,

and then restart your system and try again.

System Setup Main Menu

Option Description

System BIOS Enables you to configure BIOS settings.

iDRAC Settings Enables you to configure iDRAC settings.

The iDRAC Settings utility is an interface to set up and configure the

iDRAC parameters by using UEFI. You can enable or disable various

iDRAC parameters by using the iDRAC Settings utility. For more

information about this utility, see the Integrated Dell Remote Access

Controller User’s Guide at dell.com/esmmanuals.

Device Settings Enables you to configure device settings.

System BIOS screen

By using the System BIOS screen you can view the BIOS settings as well as edit specific functions such as

Boot Order, System Password, Setup Password, setting the RAID mode, and enabling or disabling USB

ports.

In the System Setup Main Menu, click System BIOS.

Menu Item Description

System Information Displays information about the system such as the system model name,

BIOS version and Service Tag.

Memory Settings Displays information and options related to the installed memory.

Processor Settings Displays information and options related to the processor such as speed,

cache size, and so on.

SATA Settings Displays options to enable or disable the integrated SATA controller and

ports.

Boot Settings Displays options to specify the boot mode (BIOS or UEFI). Enables you to

modify UEFI and BIOS boot settings.

Network Settings Displays options to change the network settings.

Integrated Devices Displays options to enable or disable integrated device controllers and

ports, and to specify related features and options.

Menu Item Description

Serial Communication Displays options to enable or disable the serial ports and specify related

features and options.

System Profile Settings Displays options to change the processor power management settings,

memory frequency, and so on.

System Security Displays options to configure the system security settings like, system

password, setup password, TPM security, and so on. It also enables or

disables support for the power and NMI buttons on the system.

Miscellaneous Settings Displays options to change the system date, time, and so on.

System Information screen

You can use the System Information screen to view system properties such as Service Tag, system

model, and the BIOS version.

To view the System Information click System Setup Main Menu → System BIOS → System Information.

Menu Item Description

System Model Name Displays the system model name.

System BIOS Version Displays the BIOS version installed on the system.

System Management

Engine Version

Displays the current revision of the Management Engine firmware.

System Service Tag Displays the system Service Tag.

System Manufacturer Displays the name of the system manufacturer.

System Manufacturer

Contact Information

Displays the contact information of the system manufacturer.

System CPLD Version Displays the current revision of the system CPLD firmware.

UEFI Compliance Version Displays the system firmware UEFI compliance level.

Memory Settings screen

You can use the Memory Settings screen to view all the memory settings as well as enable or disable

specific memory functions such as system memory testing and node interleaving.

To view theMemory Setting screen, click System Setup Main Menu → System BIOS → Memory Settings.

Menu Item Description

System Memory Size Displays the amount of memory installed in the system.

System Memory Type Displays the type of memory installed in the system.

System Memory Speed Displays the system memory speed.

System Memory Voltage Displays the system memory voltage.

Video Memory Displays the amount of video memory utilized.

System Memory Testing Specifies whether system memory tests are run during system boot.

Options are Enabled and Disabled. By default, the System Memory

Testing option is set to Disabled.

Memory Operating Mode Specifies the memory operating mode. The options available are

Optimizer Mode, Advanced ECC Mode, Mirror Mode, Spare Mode, and

Menu Item Description

Spare with Advanced ECC Mode. By default, the Memory Operating

Mode option is set to Optimizer Mode.

NOTE: The Memory Operating Mode can have different defaults

and available options based on the memory configuration of your

system.

Node Interleaving Specifies if Non-Uniform Memory architecture (NUMA) is supported. If

this field is Enabled, memory interleaving is supported if a symmetric

memory configuration is installed. If Disabled, the system supports

NUMA (asymmetric) memory configurations. By default, Node

Interleaving option is set to Disabled.

Snoop Mode Specifies the Snoop Mode options. Snoop Mode options available are

Home Snoop, Early Snoop, and Cluster on Die. By default, the Snoop

Mode option is set to Early Snoop. The field is only available when Node

Interleaving is Disabled.

Processor Settings screen

You can use the Processor Settings screen to view the processor settings and perform specific functions

such as enabling virtualization technology, hardware prefetcher, and logical processor idling.

To view the Processor Settings screen, click System Setup Main Menu → System BIOS → Processor

Settings.

Menu Item Description

Logical Processor Enables or disables the logical processors and displays the number of

logical processors. If the Logical Processor option is set to Enabled, the

BIOS displays all the logical processors. If this option is set to Disabled,

the BIOS displays only one logical processor per core. By default, the

Logical Processor option is set to Enabled.

Alternate RTID (Requestor

Transaction ID) Setting

Enables you to allocate more RTIDs to the remote socket, thereby

increasing cache performance between the sockets or easing work in

normal mode for NUMA. By default, the Alternate RTID (Requestor

Transaction ID) Setting is set to Disabled.

Virtualization Technology Enables or disables the additional hardware capabilities provided for

virtualization. By default, the Virtualization Technology option is set to

Enabled.

Address Translation Service

(ATS)

Defines the Address Translation Cache (ATC) for devices to cache the

DMA transactions. This field provides an interface to a chipset's Address

Translation and Protection Table to translate DMA addresses to host

addresses. By default, the option is set to Enabled.

Adjacent Cache Line

Prefetch

Optimizes the system for applications that require high utilization of

sequential memory access. By default, the Adjacent Cache Line Prefetch

option is set to Enabled. You can disable this option for applications that

require high utilization of random memory access.

Hardware Prefetcher Enables or disables the hardware prefetcher. By default, the Hardware

Prefetcher option is set to Enabled.

DCU Streamer Prefetcher Allows you to enable or disable the Data Cache Unit (DCU) streamer

prefetcher. By default, the DCU Streamer Prefetcher option is set to

Enabled.

Menu Item Description

DCU IP Prefetcher Enables or disables the Data Cache Unit (DCU) IP prefetcher. By default,

the DCU IP Prefetcher option is set to Enabled.

Execute Disable Enables or disables the execute disable memory protection technology.

By default, the Execute Disable option is set to Enabled.

Logical Processor Idling Enables or disables the operating system capability to put logical

processors in the idling state in order to reduce power consumption. By

default, the option is set to Disabled.

Configurable TDP Allows reconfiguration of Thermal Design Power (TDP) to lower levels.

TDP refers to the maximum amount of power the cooling system is

required to dissipate.

X2Apic Mode Enables or disables the X2Apic mode.

Number of Cores per

Processor

Controls the number of enabled cores in each processor. By default, the

Number of Cores per Processor option is set to All.

Processor 64-bit Support Specifies if the processor(s) support 64-bit extensions.

Processor Core Speed Displays the maximum core frequency of the processor.

Processor Bus Speed Displays the bus speed of the processor.

NOTE: The processor bus speed option displays only when both

processors are installed.

Processor 1 NOTE: Depending on the number of installed CPUs, there may be

up to two processor listings. The following settings are displayed for

each processor installed in the system.

Family-Model-Stepping Displays the family, model and stepping of the processor as defined by

Intel.

Brand Displays the brand name reported by the processor.

Level 2 Cache Displays the total L2 cache.

Level 3 Cache Displays the total L3 cache.

Number of Cores Displays the number of cores per processor.

SATA Settings screen

You can use the SATA Settings screen to view the SATA settings of SATA devices and enable RAID on

your system.

To view the SATA Settings screen click System Setup Main Menu → System BIOS → SATA Settings.

Menu Item Description

Embedded SATA Enables the embedded SATA to be set to Off, ATA, AHCI, or RAID modes.

By default, the Embedded SATA option is set to AHCI.

Security Freeze Lock Sends Security Freeze Lock command to the Embedded SATA drives

during POST. This option is applicable only to ATA and AHCI mode.

Write Cache Enables or disables the command for Embedded SATA drives during

POST.

Menu Item Description

Port A Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port B Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port C Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port D Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port E Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Menu Item Description

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port F Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port G Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port H Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port I Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Port J Sets the drive type of the selected device. For Embedded SATA settings

in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF

to turn off BIOS support.

For AHCI mode or RAID mode, BIOS always enables support.

Model Displays the drive model of the selected device.

Menu Item Description

Drive Type Displays the type of drive attached to the SATA port.

Capacity Displays the total capacity of the hard drive. The field is undefined for

removable media devices such as optical drives.

Boot Settings screen

You can use the Boot Settings screen to set the Boot mode to either BIOS or UEFI. It also allows you to

specify the boot order.

To view the Boot Settings screen click System Setup Main Menu → System BIOS → Boot Settings.

Menu Item Description

Boot Mode Enables you to set the boot mode of the system.

CAUTION: Switching the boot mode may prevent the system from

booting if the operating system is not installed in the same boot

mode.

NOTE: Setting this field to UEFI disables the BIOS Boot Settings

menu. Setting this field to BIOS disables the UEFI Boot Settings

menu.

If the operating system supports UEFI, you can set this option to UEFI.

Setting this field to BIOS allows compatibility with non-UEFI operating

systems. By default, the Boot Mode option is set to BIOS.

Boot Sequence Retry Enables or disables the Boot Sequence Retry feature. If this field is

enabled and the system fails to boot, the system reattempts the boot

sequence after 30 seconds. By default, the Boot Sequence Retry option

is set to Enabled.

Hard-Disk Failover Specifies which devices in the Hard-Disk Drive Sequence are attempted

in the boot sequence. When the option is Disabled, only the first hard

disk device in the list is attempted to boot. When set to Enabled, all hard

disk devices are attempted in order, as listed in the Hard-Disk Drive

Sequence. This option is not enabled for UEFI Boot Mode.

Boot Option Settings Configures the boot sequence and the boot devices.

Network Settings screen

You can use the Network Settings screen to modify PXE device settings. Network Settings are only

available in UEFI boot mode. BIOS does not control network settings in the BIOS boot mode. For BIOS

boot mode, the network settings are handled by the network controllers option ROM.

To view the Network Settings click System Setup Main Menu → System BIOS → Network Settings.

Menu Item Description

PXE Device n (n = 1 to 4) Enables or disables the device. When enabled, a UEFI boot option is

created for the device.

PXE Device n Settings (n = 1

to 4)

Allows you to control the configuration of the PXE device.

Integrated Devices screen details

The Integrated Devices screen allows you to view and configure the settings of all integrated devices

including the video controller, integrated RAID controller, and the USB ports.

In the System Setup Main Menu, click System BIOS → Integrated Devices.

Menu Item Description

USB 3.0 Setting Allows you to enable or disable the USB 3.0

support. Enable this option only if your operating

system supports USB 3.0. Disabling this allows

devices to operate at USB 2.0 speed. USB 3.0 is

disabled by default.

User Accessible USB Ports Allows you to enable or disable the USB ports.

Selecting Only Back Ports On disables the front

USB ports and selecting All Ports Off disables all

USB ports. The USB keyboard and mouse operates

during boot process in certain operating systems.

After the boot process is complete, the USB

keyboard and mouse do not work if the ports are

disabled.

NOTE: Selecting Only Back Ports On and All

Ports Off will disable the USB management

port and also restrict access to iDRAC

features.

Internal USB Port Allows you to enable or disable the internal USB

port. By default, the Internal USB Port option is set

to Enabled.

Integrated RAID Controller Enables or disables the integrated RAID controller.

By default, the option is set to Enabled.

Embedded NIC1 and NIC2 Allows you to enable or disable the Embedded

NIC1 and NIC2. If set to Disabled, the NIC may still

be available for shared network access by the

embedded management controller. Configure this

function using the NIC management utilities of the

system.

Embedded NIC3 and NIC4 Allows you to enable or disable the Embedded

NIC3 and NIC4 .If set to Disabled, the NIC may still

be available for shared network access by the

embedded management controller. Configure this

function using the NIC management utilities of the

system.

I/OAT DMA Engine Allows you to enable or disable the I/OAT option.

Enable only if the hardware and software supports

the feature.

Embedded Video Controller Allows you to enable or disable the Embedded

Video Controller. By default, the embedded video

controller is Enabled. If the Embedded Video

Controller is the only display capability in the

system (that is, no add-in graphics card is

installed), then the Embedded Video Controller is

automatically used as the primary display even if

the Embedded Video Controller setting is Disabled.

Current State of Embedded Video Controller Displays the current state of the Embedded Video

Controller. Current State of Embedded Video

Controller is a read only field, indicating the

current state for the Embedded Video Controller.

SR-IOV Global Enable Allows you to enable or disable the BIOS

configuration of Single Root I/O Virtualization (SR-

IOV) devices. By default, the SR-IOV Global Enable

option is set to Disabled.

OS Watchdog Timer If your system stops responding, this watchdog

timer aids in the recovery of your operating

system. When this field is set to Enabled, the

operating system is allowed to initialize the timer.

When is the field is set to Disabled (the default),

the timer will have no effect on the system.

Memory Mapped I/O above 4 GB Allows you to enable support for PCIe devices that

require large amounts of memory. By default, the

option is set to Enabled.

Slot Disablement Allows you to enable or disable the available PCIe

slots on your system. The Slot Disablement feature

controls the configuration of PCIe cards installed

in the specified slot. Slot disablement must be used

only when the installed peripheral card is

preventing booting into the operating system or

causing delays in system startup. If the slot is

disabled, both the Option ROM and UEFI driver are

disabled.

Serial Communication screen

You can use the Serial Communication screen to view the properties of the serial communication port.

To view the Serial Communication click System Setup Main Menu → System BIOS → Serial

Communication.

Menu Item Description

Serial Communication Selects serial communication devices (Serial Device 1 and Serial Device 2)

in the BIOS. BIOS console redirection can also be enabled and the port

address can be specified. By default, Serial Communication option is set

to Auto.

Serial Port Address Enables you to set the port address for serial devices. By default, the

Serial Port Address option is set to Serial Device 1=COM2, Serial Device

2=COM1

NOTE: You can use only Serial Device 2 for the Serial Over LAN

(SOL) feature. To use console redirection by SOL, configure the

same port address for console redirection and the serial device.

Menu Item Description

NOTE: Every time the system boots, the BIOS syncs the serial MUX

setting saved in iDRAC. The serial MUX setting can independently be

changed in iDRAC. Therefore, loading the BIOS default settings from

within the BIOS setup utility may not always revert this setting to the

default setting of Serial Device 1.

External Serial Connector You can associate the External Serial Connector to Serial Device 1, Serial

Device 2, or the Remote Access Device using this field.

NOTE: Only Serial Device 2 can be used for (Serial Over LAN) SOL.

To use console redirection by SOL, configure the same port address

for console redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX

setting saved in iDRAC. The serial MUX setting can independently be

changed in iDRAC. Therefore, loading the BIOS default settings from

within the BIOS setup utility may not always revert this setting to the

default setting of Serial Device 1.

Failsafe Baud Rate Displays the failsafe baud rate for console redirection. The BIOS attempts

to determine the baud rate automatically. This failsafe baud rate is used

only if the attempt fails, and the value must not be changed. By default,

the Failsafe Baud Rate option is set to 115200.

Remote Terminal Type Sets the remote console terminal type. By default, the Remote Terminal

Type option is set to VT 100/VT 220.

Redirection After Boot Enables or disables the BIOS console redirection when the operating

system is loaded. By default, the Redirection After Boot option is set to

Enabled.

System Profile Settings screen

You can use the System Profile Settings screen to enable specific system performance settings such as

power management.

To view the System Profile Settings click System Setup Main Menu → System BIOS → System Profile

Settings.

Menu Item Description

System Profile Sets the system profile. If you set the System Profile option to a mode

other than Custom, the BIOS automatically sets the rest of the options.

You can only change the rest of the options if the mode is set to Custom.

By default, the System Profile option is set to Performance Per Watt

Optimized (DAPC). DAPC is Dell Active Power Controller.

NOTE: The following parameters are available only when the System

Profile is set to Custom.

CPU Power Management Sets the CPU power management. By default, the CPU Power

Management option is set to System DBPM (DAPC). DBPM is Demand-

Based Power Management.

Memory Frequency Sets the speed of the system memory. You can select Maximum

Performance, Maximum Reliability, or a specific speed.

Turbo Boost Enables or disables the processor to operate in turbo boost mode. By

default, the Turbo Boost option is set to Enabled.

Menu Item Description

Energy Efficient Turbo Enables or disables the Energy Efficient Turbo.

Energy Efficient Turbo (EET) is a mode of operation where a processor’s

core frequency is adjusted within the turbo range based on workload.

C1E Enables or disables the processor to switch to a minimum performance

state when it is idle. By default, the C1E option is set to Enabled.

C States Enables or disables the processor to operate in all available power states.

By default, the C States option is set to Enabled.

Collaborative CPU

Performance Control

Enables or disables the CPU power management. When set to Enabled,

the CPU power management is controlled by the OS DBPM and the

System DBPM (DAPC). By default, the option is set to Disabled.

Memory Patrol Scrub Sets the memory patrol scrub frequency. By default, the Memory Patrol

Scrub option is set to Standard.

Memory Refresh Rate Sets the memory refresh rate to either 1x or 2x. By default, the Memory

Refresh Rate option is set to 1x.

Uncore Frequency Selects the Processor Uncore Frequency.

Dynamic mode allows the processor to optimize power resources across

the cores and uncore during runtime. The optimization of the uncore

frequency to either save power or optimize performance is influenced by

the setting of the Energy Efficiency Policy.

Energy Efficient Policy Enables you to selects the Energy Efficient Policy.

The CPU uses the setting to manipulate the internal behavior of the

processor and determines whether to target higher performance or

better power savings.

Number of Turbo Boot

Enabled Cores for Processor

NOTE: If there are two processors installed in the system, you see an

entry for Number of Turbo Boost Enabled Cores for Processor 2.

Controls the number of turbo boost enabled cores for processor 1. By

default, the maximum number of cores is enabled.

Monitor/Mwait Enables the Monitor/Mwait instructions in the processor. By default, the

Monitor/Mwait option is set to Enabled for all system profiles, except

Custom.

NOTE: This option can be disabled only if the C States option in

Custom mode is disabled.

NOTE: When C States is enabled in Custom mode, changing the

Monitor/Mwait setting does not impact system power/performance.

System Security Settings screen

You can use the System Security screen to perform specific functions such as setting the system

password, setup password and disabling the power button.

To view the System Security click System Setup Main Menu → System BIOS → System Security Settings.

Menu Item Description

Intel AES-NI Improves the speed of applications by performing encryption and

decryption using the Advanced Encryption Standard Instruction Set and is

set to Enabled by default.

System Password Sets the system password. This option is set to Enabled by default and is

read-only if the password jumper is not installed in the system.

Setup Password Sets the setup password. This option is read-only if the password jumper

is not installed in the system.

Password Status Locks the system password. By default, the Password Status option is set

to Unlocked.

TPM Security NOTE: The TPM menu is available only when the TPM module is

installed.

Allows you to control the reporting mode of the Trusted Platform

Module (TPM). By default, the TPM Security option is set to Off. You can

only modify the TPM Status, TPM Activation , and Intel TXT fields if the

TPM Status field is set to either On with Pre-boot Measurements or On

without Pre-boot Measurements.

TPM Information Changes the operational state of the TPM. By default, the TPM Activation

option is set to No Change.

TPM Status Displays the TPM status.

TPM Command CAUTION: Clearing the TPM results in the loss of all keys in the

TPM. The loss of TPM keys may affect booting to the operating

system.

Clears all the contents of the TPM. By default, the TPM Clear option is set

to No.

Intel TXT Enables or disables the Intel Trusted Execution Technology (TXT). To

enable Intel TXT, Virtualization Technology must be enabled and TPM

Security must be Enabled with Pre-boot measurements. By default, the

Intel TXT option is set to Off

Power Button Enables or disables the power button on the front of the system. By

default, the Power Button option is set to Enabled.

NMI Button Enables or disables the NMI button on the front of the system. By default,

the NMI Button option is set to Disabled.

AC Power Recovery Sets how the system reacts after AC power is restored to the system. By

default, the AC Power Recovery option is set to Last.

AC Power Recovery Delay Sets how the system supports staggering of power up after AC power is

restored to the system. By default, the AC Power Recovery Delay option

is set to Immediate.

User Defined Delay (60s to

240s)

Sets the User Defined Delay when the User Defined option for AC Power

Recovery Delay is selected.

UEFI Variable Access Provides varying degrees of securing UEFI variables. When set to

Standard (the default) UEFI variables are accessible in the Operating

System per the UEFI specification. When set to Controlled, selected UEFI

variables are protected in the environment and new UEFI boot entries are

forced to be at the end of the current boot order.

Menu Item Description

Secure Boot Enables Secure Boot, where the BIOS authenticates each pre-boot image

using the certificates in the Secure Boot Policy. Secure Boot is disabled

by default.

Secure Boot Policy When Secure Boot policy is Standard, the BIOS uses the system

manufacturer’s key and certificates to authenticate pre-boot images.

When Secure Boot policy is Custom, the BIOS uses the user-defined key

and certificates. Secure Boot policy is Standard by default.

Secure Boot Policy

Summary

Displays the list of certificates and hashes that secure boot uses to

authenticate images.

Secure Boot Custom Policy Settings screen

Secure Boot Custom Policy Settings is displayed only when Secure Boot Policy is set to Custom.

In the System Setup Main Menu, click System BIOS → System Security → Secure Boot Custom Policy

Settings.

Menu Item Description

Platform Key Imports, exports, deletes, or restores the platform

key (PK).

Key Exchange Key Database Allows you to import, export, delete, or restore

entries in the Key Exchange Key (KEK) Database.

Authorized Signature Database Imports, exports, deletes, or restores entries in the

Authorized Signature Database (db).

Forbidden Signature Database Imports, exports, deletes, or restores entries in the

Forbidden Signature Database (dbx).

Miscellaneous Settings screen

You can use the Miscellaneous Settings screen to perform specific functions such as updating the asset

tag, and changing the system date and time.

To view the Miscellaneous Settings click System Setup Main Menu → System BIOS → Miscellaneous

Settings.

Menu Item Description

System Time Enables you to set the time on the system.

System Date Enables you to set the date on the system.

Asset Tag Displays the asset tag and enables you to modify it for security and

tracking purposes.

Keyboard NumLock Enables you to set whether the system boots with the NumLock enabled

or disabled. By default the Keyboard NumLock is set to On.

NOTE: This option does not apply to 84-key keyboards.

F1/F2 Prompt on Error Enables or disables the F1/F2 prompt on error. By default, F1/F2 Prompt

on Error is set to Enabled. The F1/F2 prompt also includes keyboard

errors.

Load Legacy Video Option

ROM

Enables you to determine whether the system BIOS loads the legacy

video (INT 10H) option ROM from the video controller. Selecting Enabled

Menu Item Description

in the operating system does not support UEFI video output standards.

This field is only for UEFI boot mode. You cannot set this to Enabled if

UEFI Secure Boot mode is enabled.

About Boot Manager

Boot Manager enables you to add, delete, and arrange boot options. You can also access System Setup

and boot options without restarting the system.

Entering Boot Manager

The Boot Manager screen allows you to select boot options and diagnostic utilities.

1. Turn on or restart your system.

2. Press <F11> when you see the message <F11> = Boot Manager.

If your operating system begins to load before you press <F11>, allow the system to finish booting,

and then restart your system and try again.

Boot Manager main menu

Menu Item Description

Continue Normal Boot The system attempts to boot to devices starting

with the first item in the boot order. If the boot

attempt fails, the system continues with the next

item in the boot order until the boot is successful

or no more boot options are found.

One Shot Boot Menu Takes you to the boot menu where you can select

a one time boot device to boot from.

Launch System Setup Enables you to access the System Setup.

Launch Lifecycle Controller Exits the Boot Manager and invokes the Lifecycle

Controller program.

System Utilities Launches system utilities menu such as system

diagnostics and UEFI shell.

About Dell Lifecycle Controller

Dell Lifecycle Controller allows you to perform useful tasks such as configuring BIOS and hardware

settings, deploying an operating system, updating drivers, changing RAID settings, and saving hardware

profiles. For more information about Dell Lifecycle Controller, see the documentation at dell.com/

esmmanuals.

Changing the boot order

You may have to change the boot order if you want to boot from a USB key or an optical drive. The

instructions given below may vary if you have selected BIOS for Boot Mode.

1. In the System Setup Main Menu, click System BIOS → Boot Settings.

2. Click Boot Option Settings → Boot Sequence.

3. Use the arrow keys to select a boot device, and use the <+> and <-> keys to move the device down

or up in the order.

4. Click Exit, click Yes to save the settings on exit.

Choosing the system boot mode

System Setup enables you to specify the boot mode for installing your operating system:

• BIOS boot mode (the default) is the standard BIOS-level boot interface.

• UEFI boot mode is an enhanced 64-bit boot interface based on Unified Extensible Firmware Interface

(UEFI) specifications that overlays the system BIOS.

To choose the system Boot Mode:

1. In System Setup click Boot Settings and select Boot Mode.

2. Select the Boot Mode you want the system to boot into.

NOTE: After the system boots in the specified boot mode, proceed to install your operating system

from that mode.

CAUTION: Trying to boot the operating system from the other boot mode will cause the system

to halt at startup.

NOTE: Operating systems must be UEFI-compatible to be installed from the UEFI boot mode. DOS

and 32-bit operating systems do not support UEFI and can only be installed from the BIOS boot

mode.

NOTE: For the latest information on supported operating systems, go to dell.com/ossupport .

Assigning a system and setup password

Prerequisites

NOTE: The password jumper enables or disables the System Password and Setup Password

features..

You can assign a new System Password and Setup Password or change an existing System Password

and Setup Password only when the password jumper setting is Enabled and Password Status is

Unlocked.

If the password jumper setting is disabled, the existing System Password and Setup Password is deleted

and you need not provide the system password to boot the system.

About this task

To assign a System Password and Setup Password, follow the steps below:

Steps

1. To enter System Setup, press <F2> immediately after a power-on or reboot.

2. From the System Setup Main Menu, select System BIOS and press <Enter>.

The System BIOS screen is displayed.

3. On the System BIOS screen, select System Security and press <Enter>.

The System Security screen is displayed.

4. On the System Security screen, verify that Password Status is Unlocked.

5. Select System Password, enter your system password, and press <Enter> or <Tab>.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

A message prompts you to re-enter the system password.

6. Re-enter the system password, and click OK.

7. Select Setup Password, enter your setup password and press <Enter> or <Tab>.

A message prompts you to re-enter the setup password.

8. Re-enter the setup password, and click OK.

9. Press <Esc> to return to the System BIOS screen. Press <Esc> again.

A message prompts you to save the changes.

NOTE: Password protection does not take effect until the system reboots.

Related Links

System board connectors

Using your system password to secure your system

Prerequisites

NOTE: If you have assigned a setup password, the system accepts your setup password as an

alternate system password.

Steps

1. Turn on or reboot your system.

2. Type your password and press <Enter>.

Next steps

When Password Status is Locked, type the password and press <Enter> when prompted at reboot.

If an incorrect system password is entered, the system displays a message and prompts you to re-enter

your password. You have three attempts to enter the correct password. After the third unsuccessful

attempt, the system displays an error message that the system has halted and must be powered down.

Even after you shut down and restart the system, the error message is displayed until the correct

password is entered.

NOTE: You can use the Password Status option in conjunction with the System Password and

Setup Password options to protect your system from unauthorized changes.

Deleting or changing an existing system and/or setup

password

Prerequisites

Ensure that the Password jumper is set to enabled and the Password Status is set to Unlocked before

attempting to delete or change the existing System and/or Setup password. You cannot delete or change

an existing System or Setup password if the Password Status is Locked.

Steps

1. To enter System Setup, press <F2> immediately after a power-on or restart.

2. In the System Setup Main Menu, select System BIOS and press <Enter>.

The System BIOS screen is displayed.

3. In the System BIOS Screen, select System Security and press <Enter>.

The System Security screen is displayed.

4. In the System Security screen, verify that Password Status is set to Unlocked.

5. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.

6. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.

NOTE: If you change the System and/or Setup password, a message prompts you to re-enter

the new password. If you delete the System and/or Setup password, a message prompts you to

confirm the deletion.

7. Press <Esc> to return to the System BIOS screen. Press <Esc> again, and a message prompts you to

save the changes.

Operating with a setup password enabled

If Setup Password is Enabled, enter the correct setup password before modifying most of the System

Setup options.

If you do not enter the correct password in three attempts, the system displays the message

Invalid Password! Number of unsuccessful password attempts: <x> System Halted!

Must power down.

Even after you shut down and restart the system, the error message is displayed until the correct

password is entered. The following options are exceptions:

• If System Password is not Enabled and is not locked through the Password Status option, you can

assign a system password.

• You cannot disable or change an existing system password.

NOTE: You can use the Password Status option in conjunction with the Setup Password option to

protect the system password from unauthorized changes.

Embedded system management

The Dell Lifecycle Controller provides advanced embedded systems management throughout the

server’s lifecycle. The Lifecycle Controller can be started during the boot sequence and can function

independently of the operating system.

NOTE: Certain platform configurations may not support the full set of features provided by the

Lifecycle Controller.

For more information about setting up the Lifecycle Controller, configuring hardware and firmware, and

deploying the operating system, see the Lifecycle Controller documentation at dell.com/support/home.

iDRAC Settings utility

The iDRAC Settings utility is an interface to set up and configure the iDRAC parameters using UEFI. You

can enable or disable various iDRAC parameters using the iDRAC Settings Utility.

NOTE: Accessing some of the features on the iDRAC Settings utility requires the iDRAC Enterprise

License upgrade.

For more information on using iDRAC, see the iDRAC User's Guide at dell.com/esmmanuals.

Entering the iDRAC Settings utility

1. Turn on or restart the managed system.

2. Press <F2> during Power-on Self-test (POST).

3. In the System Setup Main Menu page, click iDRAC Settings.

The iDRAC Settings screen is displayed.

Changing the Thermal Settings

The iDRAC Settings utility enables you to select and customize the thermal control settings for your

system.

1. Enter the iDRAC Settings utility.

2. Under iDRAC Settings → Thermal → User Option, select between the following options:

• Default

• Maximum Exhaust Temperature

• Fan Speed Offset

NOTE: When the User Option is set to the default Auto setting, the user option cannot be

modified.

3. Set the Maximum Air Exhaust Temperature or the Fan Speed Offset fields.

4. Click Back → Finish → Yes.

Installing and removing system

components

Safety instructions

WARNING: Whenever you need to lift the system, get others to assist you. To avoid injury, do not

attempt to lift the system by yourself.

WARNING: Opening or removing the system cover while the system is powered on may expose

you to a risk of electric shock.

CAUTION: Do not operate the system without the cover for a duration exceeding five minutes.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: It is recommended that you always use a static mat and static strap while working on

components inside the system.

NOTE: To ensure proper operation and cooling, all bays in the system must be populated at all

times with either a module or with a blank.

Before working inside your system

1. Turn off the system, including any attached peripherals.

2. Disconnect the system from the electrical outlet and disconnect the peripherals.

3. If installed, remove the front bezel.

4. Remove the system cover.

Related Links

Removing the front bezel

Removing the system cover

After working inside your system

1. Install the system cover.

2. If applicable, install the front bezel.

3. Reconnect the system to its electrical outlet.

4. Turn the system on, including any attached peripherals.

Related Links

Installing the system cover

Installing the front bezel

Recommended tools

You need the following tools to perform the removal and installation procedures:

• Key to the front bezel lock. This is required only if you have a front bezel.

• #1 Phillips screwdriver

• #2 Phillips screwdriver

The following tools are required for assembling the cables for a DC power supply unit (PSU):

• AMP 90871-1 or Tyco Electronics 58433-3 or equivalent hand-crimping tool

• Wire-stripper pliers capable of removing insulation from size 10 AWG solid or stranded, insulated

copper wire

NOTE: Use alpha wire part number 3080 or equivalent (65/30 stranding).

Front bezel (optional)

Removing the front bezel

1. Unlock the bezel.

2. Lift the release latch next to the lock.

3. Rotate the left end of the bezel away from the front panel.

4. Unhook the right end of the bezel and pull the bezel away from the system.

1. bezel lock 2. front bezel

Installing the front bezel

1. Hook the right end of the bezel onto the chassis.

2. Fit the free end of the bezel onto the system.

3. Lock the bezel.

Figure 9. Removing and installing the front bezel

1. release latch 2. keylock

3. front bezel

Removing and installing the system cover

WARNING: Whenever you need to lift the system, get others to assist you. To avoid injury, do not

attempt to lift the system by yourself.

WARNING: Installing or removing the system cover when the system is on may expose you to a

risk of electric shock.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: Do not operate the system without the cover for a duration exceeding five minutes.

Removing the system cover

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. On top of the system, locate the latch release lock and rotate the lock to the unlocked position.

2. Lift the latch and slide the cover back. The system cover slides back and the tabs on the system cover

disengages from the slots on the chassis.

3. Hold the cover on both sides and lift the cover away from the system.

Figure 10. Opening and closing the system

1. system cover 2. latch

3. latch release lock

Next steps

1. Install the system cover.

2. Follow the procedure listed in After working inside your system..

Related Links

Installing the system cover

Prerequisites

Ensure that you read the Safety instructions.

Steps

1. Align the slots of the system cover with the tabs on the chassis.

2. Press the cover release latch, and push the cover toward the front of the chassis until the latch locks

into place.

3. Turn the cover latch release lock clockwise to the locked position.

Next steps

1. Install the bezel (optional).

2. Follow the procedure listed in After working inside your system.

Related Links

Installing the front bezel

Inside the system

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: Components that are hot-swappable are marked orange, and touch-points on the

components are marked blue.

Figure 11. Inside the System—Redundant Power Supply Unit Chassis

1. control-panel board 2. hard-drive backplane

3. cooling fan (5) 4. power-interposer board

5. power supply (redundant) 6. optional expansion-card riser

7. processor (2) 8. DIMM (12)

Figure 12. Inside the System—Non-Redundant Power Supply Unit Chassis

1. control-panel board 2. hard-drive backplane

3. cooling fans (5) 4. power supply ( non redundant)

5. optional expansion-card riser 6. processor (2)

7. DIMM (12)

Cooling shroud

Removing the cooling shroud

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. If applicable, disconnect the power or data cables from expansion card (s).

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full-

length card.

4. If installed, remove the expansion-card riser

CAUTION: Never operate your system with the cooling shroud removed. The system may get

overheated quickly, resulting in shutdown of the system and loss of data.

Steps

Hold and lift the cooling shroud away from the system.

Figure 13. Removing and installing the cooling shroud

1. cooling shroud 2. chassis intrusion switch

3. chassis intrusion switch connector on

system board 4. cooling shroud alignment slots

5. cooling shroud alignment pins

Next steps

1. Install the optional PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full-length

expansion card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the (optional) expansion-card riser

Removing an expansion card from the expansion-card riser

Installing an expansion card into the expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: For proper seating of the cooling shroud in the chassis, ensure that the cables inside the

system are routed along the chassis wall and secured using the cable securing bracket.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Align the tabs on the cooling shroud with the securing holes at the back of the chassis.

2. Lower the cooling shroud into the chassis until it is firmly seated.

Next steps

1. Install the optional PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. If applicable open the expansion-card latch on the cooling shroud to secure the full-length

expansion card.

4. Follow the procedure listed in After working inside your system.

Related Links

Installing an expansion card into the expansion-card riser

Installing the (optional) expansion-card riser

System memory

Your system supports DDR4 registered DIMMs (RDIMMs). It supports DDR4 voltage specifications.

NOTE: MT/s indicates DIMM speed in MegaTransfers per second.

Memory bus operating frequency can be 2133 MT/s, 1866 MT/s, 1600 MT/s, or 1333 MT/s depending on:

• System profile selected (for example, Performance Optimized, Custom, or Dense Configuration

Optimized)

• Maximum supported DIMM frequency of the processors

Your system contains 12 memory sockets split into four sets— two sets of 4 sockets and two sets of 2

sockets each. DIMMs in sockets A1 to A8 are assigned to processor 1 and DIMMs in sockets B1 to B4 are

assigned to processor 2. Each 4-socket set is organized into two channels and each 2–socket set is

organized into one channel. In each channel of the 4-socket set, the release levers of the first socket are

marked white and those of the second socket are marked black. In the 2-socket set, each release lever is

marked white.

Figure 14. Memory socket locations

Memory channels are organized as follows:

Processor 1 channel 0: slots A1 and A5

channel 1: slots A2 and A6

channel 2: slots A3 and A7

channel 3: slots A4 and A8

Processor 2 channel 0: slot B1

channel 1: slot B2

channel 2: slot B3

channel 3: slot B4

The following table shows the memory populations and operating frequencies for the supported

configurations.

DIMM Type DIMMs Populated/

Channel Operating Frequency (in

MT/s) Maximum DIMM Rank/Channel

1.2 V

RDIMM 12133, 1866, 1600, and 1333 Single rank or dual rank

General memory module installation guidelines

Your system supports Flexible Memory Configuration, enabling the system to be configured and run in

any valid chipset architectural configuration. The following are the recommended guidelines for installing

memory modules:

• x4 and x8 DRAM based DIMMs can be mixed. For more information, see Mode-specific guidelines.

• Up to two dual- or single-rank RDIMMs can be populated per channel.

• Populate DIMM sockets only if a processor is installed. For single-processor systems, sockets A1 to A8

are available. For dual-processor systems, sockets A1 to A8 and sockets B1 to B4 are available.

• Populate all sockets with white release levers first, and then all the sockets with black release levers.

• When mixing memory modules with different capacities, populate the sockets with memory modules

with highest capacity first. For example, if you want to mix 4 GB and 8 GB DIMMs, populate 8 GB

DIMMs in the sockets with white release levers and 4 GB DIMMs in the sockets with black release

levers.

• In a dual-processor configuration, the memory configuration for each processor should be identical

through the first eight slots. For example, if you populate socket A1 for processor 1, then populate

socket B1 for processor 2, and so on.

• Memory modules of different capacities can be mixed provided other memory population rules are

followed (for example, 4 GB and 8 GB memory modules can be mixed).

• Mixing of more than two DIMM capacities in a system is not supported.

• Populate two DIMMs per processor (one DIMM per channel) at a time to maximize performance.

Mode-specific guidelines

Four memory channels are allocated to each processor. The allowable configurations depend on the

memory mode selected.

NOTE: You can mix x4 and x8 DRAM based DIMMs to support RAS features. However, all guidelines

for specific RAS features must be followed. x4 DRAM based DIMMs retain Single Device Data

Correction (SDDC) in memory optimized (independent channel) mode. x8 DRAM based DIMMs

require Advanced ECC mode to gain SDDC.

The following sections provide additional slot population guidelines for each mode:

Advanced ECC (lockstep)

Advanced ECC mode extends SDDC from x4 DRAM based DIMMs to both x4 and x8 DRAMs. This

protects against single DRAM chip failures during normal operation.

Memory installation guidelines:

• Memory modules must be identical in size, speed, and technology.

• DIMMs installed in memory sockets with white release levers must be identical and similar rule applies

for sockets with black release levers. This ensures that identical DIMMs are installed in matched pairs -

for example, A1 with A2, A3 with A4, A5 with A6, and so on.

NOTE: Advanced ECC with Mirroring is not supported.

Memory optimized (independent channel) mode

This mode supports SDDC only for memory modules that use x4 device width, and the mode does not

impose any specific slot population requirements.

Memory sparing

NOTE: To use memory sparing, this feature must be enabled in the System Setup.

In this mode, one rank per channel is reserved as a spare. If persistent correctable errors are detected on

a rank, the data from this rank is copied to the spare rank and the failed rank is disabled.

With memory sparing enabled, the system memory available to the operating system is reduced by one

rank per channel. For example, in a dual-processor configuration with sixteen 4 GB dual-rank DIMMs, the

available system memory is: 3/4 (ranks/channel) × 16 (DIMMs) × 4 GB = 48 GB, and not 16 (DIMMs) × 4

GB = 64 GB.

NOTE: Memory sparing does not offer protection against a multi-bit uncorrectable error.

NOTE: Both Advanced ECC/Lockstep and Optimizer modes support Memory Sparing.

Sample memory configurations

The following tables show sample memory configurations for one and two processor configurations that

follow the appropriate memory guidelines.

NOTE: 1R and 2R in the following tables indicate single- and dual-rank DIMMs respectively.

Table 1. Memory configurations—single processor

System

Capacity (in

GB)

DIMM Size

(in GB) Number of

DIMMs DIMM Rank,

Organization, and

Frequency

DIMM Slot Population

4 4 1 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

8 4 2 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2

16 4 4 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2, A3, A4

8 2 2R, x8, 2133 MT/s,

2R, x8, 1866 MT/s

A1, A2

System

Capacity (in

GB)

DIMM Size

(in GB) Number of

DIMMs DIMM Rank,

Organization, and

Frequency

DIMM Slot Population

24 4 6 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2, A3, A4, A5, A6

48 8 6 2R, x8, 2133 MT/s,

2R, x8, 1866 MT/s

A1, A2, A3, A4, A5, A6

96 16 6 2R, x4, 2133 MT/s,

2R, x4, 1866 MT/s

A1, A2, A3, A4, A5, A6

128 16 8 2R, x4, 2133 MT/s,

2R, x4, 1866 MT/s,

A1, A2, A3, A4, A5, A6, A7, A8

192 32 6 RDIMM, 2R, x4, 2133

MT/s

RDIMM, 2R, x4, 1866

MT/s

A1, A2, A3, A4, A5, A6

Table 2. Memory configurations—two processors

System

Capacity (in

GB)

DIMM Size (in

GB) Number of

DIMMs DIMM Rank,

Organization, and

Frequency

DIMM Slot Population

16 4 4 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2, B1, B2

32 4 8 1R, x8, 2133 MT/s,

1R, x8, 1866 MT/s

A1, A2, A3, A4, B1, B2, B3, B4

64 8 8 2R, x8, 2133 MT/s,

2R, x8, 1866 MT/s

A1, A2, A3, A4, B1, B2, B3, B4

96 8 12 2R, x8, 2133 MT/s,

2R, x8, 1866 MT/s

A1, A2, A3, A4, A5, A6,A7,A8, B1,

B2, B3, B4

128 16 8 2R, x4, 2133 MT/s,

2R, x4, 1866 MT/s

A1, A2, A3, A4, B1, B2, B3, B4

160 16 and 8 12 2R, x4, 2133 MT/s,

2R, x8, 2133 MT/s,

2R, x4, 1866 MT/s

A1, A2, A3, A4, A5, A6,A7,A8, B1,

B2, B3, B4

System

Capacity (in

GB)

DIMM Size (in

GB) Number of

DIMMs DIMM Rank,

Organization, and

Frequency

DIMM Slot Population

2R, x8, 1866 MT/s NOTE: 16 GB DIMMs must

be installed in slots

numbered A1, A2, A3, A4,

B1, B2, B3, and B4 and 8

GB DIMMs must be

installed in slots A5, A6, A7,

and A8.

192 16 12 2R, x4, 2133 MT/s,

2R, x4, 1866 MT/s

A1, A2, A3, A4, A5, A6,A7,A8, B1,

B2, B3, B4

384 32 12 RDIMM, 2R, x4, 2133

MT/s

RDIMM, 2R, x4, 1866

MT/s

A1, A2, A3, A4, A5, A6,A7,A8, B1,

B2, B3, B4

Removing a memory module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full-

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser.

WARNING: The memory modules are hot to the touch for some time after the system has been

powered down. Allow time for the memory modules to cool before handling them. Handle the

memory modules by the card edges and avoid touching the components or metallic contacts on

the memory module.

CAUTION: To ensure proper system cooling, memory-module blanks must be installed in any

memory socket that is not occupied. Remove memory-module blanks only if you intend to install

memory modules in those sockets.

Steps

1. Locate the appropriate memory module socket.

CAUTION: Handle each memory module only by the card edges, making sure not to touch

the middle of the memory module or metallic contacts.

2. To release the memory module from the socket, simultaneously press the ejectors on both ends of

the memory-module socket.

3. Lift the memory module out of the system.

Figure 15. Removing and installing a memory module

1. memory-module 2. memory-module socket

3. memory module socket ejector (2)

Next steps

1. If you are removing the memory module permanently, install a memory module blank.

2. If applicable, install the PCIe expansion-card riser.

3. If applicable, connect the required power or data cables to the expansion card(s).

4. Reinstall the cooling shroud.

5. If applicable open the expansion-card latch on the cooling shroud to secure the full-length

expansion card.

6. Follow the procedure listed in After working inside your system.

Related Links

Removing the (optional) expansion-card riser

Removing an expansion card from the expansion-card riser

Removing the cooling shroud

Installing memory modules

Installing an expansion card into the expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Installing memory modules

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. If applicable, remove the PCIe expansion-card riser

4. Remove the cooling shroud.

WARNING: The memory modules are hot to the touch for some time after the system has been

powered down. Allow time for the memory modules to cool before handling them. Handle the

memory modules by the card edges and avoid touching the components or metallic contacts on

the memory module.

Steps

1. Locate the appropriate memory-module socket.

CAUTION: Handle each memory module only by the card edges, making sure not to touch

the middle of the memory module or metallic contacts.

2. If a memory module or a memory-module blank is installed in the socket, remove it.

NOTE: Retain the removed memory-module blank(s) for future use.

CAUTION: To prevent damage to the memory module or the memory-module socket during

installation, do not bend or flex the memory module; insert both ends of the memory module

simultaneously.

3. Align the edge connector of the memory module with the alignment key of the memory module

socket, and insert the memory module in the socket.

NOTE: The memory-module socket has an alignment key that allows you to install the memory

module in the socket in only one orientation.

CAUTION: Do not apply pressure at the center of the memory module; apply pressure at both

ends of the memory module evenly.

4. Press the memory module with your thumbs until the socket levers firmly click into place.

Figure 16. Installing the memory module

1. memory module 2. alignment key

3. memory-module socket ejector (2)

When the memory module is properly seated in the socket, the levers on the memory module socket

align with the levers on the other sockets that have memory modules installed.

5. Repeat steps 3 and 4 of this procedure to install the remaining memory modules.

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. Reinstall the cooling shroud.

3. Follow the procedure listed in After working inside your system.

4. Press <F2> to enter System Setup, and check the System Memory setting.

The system should have already changed the value to reflect the installed memory.

5. If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat

steps 2 and 3 of Removing a memory module procedure, checking to ensure that the memory

modules are firmly seated in their sockets.

6. Run the system memory test in the system diagnostics.

Related Links

Removing the (optional) expansion-card riser

Removing an expansion card from the expansion-card riser

Removing the cooling shroud

Installing an expansion card into the expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Hard drives

Your system supports up to eight 3.5 inch or 2.5 inch hot-swappable hard disk drives/SSDs.

All hard drives connect to the system board through the hard-drive backplane. Hot-swappable hard

drives are supplied in hot-swappable hard-drive carriers that fit in the hard-drive slots.

CAUTION: Before attempting to remove or install a hard drive while the system is running, see the

documentation for the storage controller card to ensure that the host adapter is configured

correctly to support hot-swap hard drive removal and insertion.

CAUTION: Do not turn off or reboot your system while the hard drive is being formatted. Doing

so can cause a hard drive failure.

NOTE: Use only hard drives that have been tested and approved for use with the hard-drive

backplane.

When you format a hard drive, allow enough time for the formatting to be completed. Be aware that

high-capacity hard drives can take a number of hours to format.

Removing a hot-swap hard drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. If installed, remove the front bezel.

3. Using the management software, prepare the hard drive for removal. For more information, see the

documentation for the storage controller.

If the hard drive is online, the green activity/fault indicator flashes as the drive is turned off. You can

remove the hard-drive when the hard-drive indicators turn off.

CAUTION: To prevent data loss, ensure that your operating system supports hot-swap drive

installation. See the documentation supplied with your operating system.

Steps

1. Press the release button to open the hard-drive carrier release handle.

2. Slide the hard-drive carrier out of the hard-drive slot.

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have hard-

drive blanks installed.

3. If you are not replacing the hard drive immediately, insert a hard-drive blank in the empty hard-drive

slot.

Figure 17. Removing and installing a hot-swap hard drive

1. release button 2. hard-drive carrier

3. hard-drive carrier handle

Next steps

If removed, install the front bezel.

Related Links

Removing the front bezel

Installing the front bezel

Installing a hot-swap hard drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. If applicable, remove the front bezel.

CAUTION: Use only hard drives that have been tested and approved for use with the hard-drive

backplane.

CAUTION: Combining SAS and SATA hard drives in the same RAID volume is not supported.

CAUTION: When installing a hard drive, ensure that the adjacent drives are fully installed.

Inserting a hard-drive carrier and attempting to lock its handle next to a partially installed carrier

can damage the partially installed carrier's shield spring and make it unusable.

CAUTION: To prevent data loss, ensure that your operating system supports hot-swap drive

installation. See the documentation supplied with your operating system.

CAUTION: When a replacement hot-swappable hard drive is installed and the system is powered

on, the hard drive automatically begins to rebuild. Make absolutely sure that the replacement

hard drive is blank or contains data that you wish to have over-written. Any data on the

replacement hard drive is immediately lost after the hard drive is installed.

Steps

1. If a hard-drive blank is installed in the hard-drive slot, remove it.

2. Install a hard drive in the hard-drive carrier.

3. Press the release button on the front of the hard-drive carrier and open the hard-drive carrier handle.

4. Insert the hard-drive carrier into the hard-drive slot until the carrier connects with the backplane.

5. Close the hard-drive carrier handle to lock the hard drive in place.

Next steps

Install the optional front bezel.

1. Follow the procedure listed in After working inside your system.

2. Install the optional front bezel.

Related Links

Removing the front bezel

Installing a hot-swap hard drive

Installing the front bezel

Removing a 3.5 inch hard-drive blank

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have drive blanks

installed.

1. Ensure that you read the Safety instructions.

2. If installed, remove the front bezel.

Steps

Press the release button and slide the blank out of the hard-drive slot.

Figure 18. Removing and installing a 3.5 inch hard-drive blank

1. hard-drive blank 2. release button

Next steps

If applicable, install the front bezel.

Related Links

Removing the front bezel

Installing the front bezel

Installing a 3.5 inch hard-drive blank

Prerequisites

1. Ensure that you read the Safety instructions.

2. If applicable, remove the front bezel.

Steps

Insert the hard-drive blank into the hard-drive slot following the sequence in the image below and

push the hard-drive blank until the release button clicks into place.

Figure 19. Hard-drive blank installation sequence

Next steps

If applicable, install the front bezel.

Related Links

Removing the front bezel

Installing the front bezel

Removing a 2.5 inch hard drive from a 3.5 inch hard-drive adapter

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver ready.

NOTE: A 2.5 inch hard drive is installed in a 3.5 inch hard-drive adapter, which is then installed in the

3.5 inch hard-drive carrier.

Steps

1. Remove the screws from the side of the 3.5 inch hard-drive adapter.

2. Remove the hard drive from the hard-drive adapter.

Installing a 2.5 inch hard drive into a 3.5 inch hard-drive adapter

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver ready.

Steps

1. Align the screw holes on the 2.5 inch hard drive with the screw holes on the 3.5 inch hard-drive

adapter.

2. Install the screws to secure the hard drive to the hard-drive adapter.

Figure 20. Removing and installing a 2.5 inch hard drive into a 3.5 inch hard-drive adapter

1. 2.5 inch hard drive 2. 3.5 inch hard-drive adapter

3. screw (2)

Removing a hard-drive adapter from a hard-drive carrier

Prerequisites

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver ready.

Steps

1. Remove the screws from the slide rails on the hard-drive carrier.

2. Lift the hard-drive adapter out of the hard-drive carrier.

Installing a hard-drive adapter into a hard-drive carrier

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Keep the #2 Phillips screwdriver ready.

Steps

1. Insert the hard-drive adapter into the hard-drive carrier with the connector end of the hard drive

toward the back of the hard-drive carrier.

2. Align the screw holes on the hard drive with the holes on the hard-drive carrier.

3. Install the screws to secure the hard drive to the hard-drive carrier.

Figure 21. Removing and installing a hard-drive adapter into a 3.5 inch hard-drive carrier

1. 3.5 inch hard-drive carrier 2. screw (5)

3. hard-drive adapter 4. 2.5 inch hard drive

Removing a hard drive from a hard-drive carrier

Prerequisites

1. Keep the #2 Phillips screwdriver ready.

2. Remove the hard-drive carrier from the system.

Steps

1. Remove the screws from the slide rails on the hard-drive carrier.

2. Lift the hard drive out of the hard-drive carrier.

Figure 22. Removing and installing a hard drive into a hard-drive carrier

1. screw (4) 2. hard drive

3. hard-drive carrier

Installing a hard drive into a hard-drive carrier

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Keep the #2 Phillips screwdriver ready.

Steps

1. Insert the hard drive into the hard-drive carrier with the connector end of the hard drive toward the

back of the hard-drive carrier.

2. Align the screw holes on the hard drive with the screw holes on the hard-drive carrier.

When aligned correctly, the back of the hard drive is flush with the back of the hard-drive carrier.

3. Attach the screws to secure the hard drive to the hard-drive carrier.

Optical drive (optional)

Removing the optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Disconnect the power/data cable from the back of the optical drive.

NOTE: Note the routing of the power/data cable as you remove them from the system board

and drive. You must route these cables properly when you replace them to prevent them from

being pinched or crimped.

2. Press down and push the blue release tab toward the front of the system.

3. Slide the optical drive out of the system until it is free of the drive bay.

Figure 23. Removing and installing the optical drive

1. optical drive 2. power cable

3. data cable 4. release tab

Next steps

1. If you are not adding a new optical drive, install the optical drive blank.

2. Install the optional front bezel

3. Follow the procedure listed in After working inside your system.

Installing the optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. If installed, remove the optical drive blank, and then press the blue release tab at the back of the

blank and push the blank out of the system.

2. Align the optical drive with the optical drive slot on the front of the chassis.

3. Slide the optical drive into the slot until the latch snaps into place.

4. Connect the power/data cable to the back of the drive.

5. Route the power/data cable through the cable routing guides on the system chassis.

Next steps

1. Follow the procedure listed in After working inside your system.

Cooling fans

Your system supports five cooling fans. A fan blank is pre-installed on the first cooling fan slot (FAN1).

NOTE: Hot-swap removal or installation of the fans is not supported.

NOTE: Each fan is listed in the system’s management software, referenced by the respective fan

number. If there is a problem with a particular fan, you can easily identify and replace the proper fan

by noting the fan numbers on the cooling fan assembly.

Listed below is the Fan configuration table which lists out the various fan configurations based on the

CPU configuration in the server.

Table 3. Fan configuration table

CPU Type CPU 1 CPU 2 PSU Type FAN1 FAN2 FAN3 FAN4 FAN5 FAN6

55W-120W

Y N Redundant /

Cabled

N Y Y Y Y N

Y Y Redundant /

Cabled

N Y Y Y Y Y

Removing a cooling fan

Prerequisites

WARNING: Opening or removing the system cover when the system is ON may expose you to a

risk of electric shock. Exercise utmost care while removing or installing cooling fans.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: The procedure for removing each cooling fan is the same.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. If applicable, remove the expansion-card riser.

4. Remove the cooling shroud.

Steps

1. Remove the fan cable connector from the system board by pressing the release tab on the system

board end of the connector, and lifting it away from the system board.

2. Free the cable from the cable holders on the fan bracket.

3. Press the release tab on the cooling fan and lift the fan away from the chassis.

Figure 24. Removing and installing a cooling fan

1. cooling fans (5) 2. cooling fan release tab

3. cooling fan cable connector 4. cooling fan connector on the system

board

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. Reinstall the cooling shroud.

3. Follow the procedure listed in After working inside your system.

Installing a cooling fan

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Align the fan with the cable end of the fan toward the system board connector.

2. Lower the fan into the fan bracket until it clicks into position.

3. Connect the fan's power cable to the corresponding power connector on the system board.

4. Route the cable through the cable holders on the fan bracket.

Next steps

Follow the procedure listed in After working inside your system.

Internal USB memory key (optional)

An optional USB memory key installed inside your system can be used as a boot device, security key, or

mass storage device. The USB connector must be enabled by the Internal USB Port option in the

Integrated Devices screen of the System Setup.

To boot from the USB memory key, configure the USB memory key with a boot image, and then specify

the USB memory key in the boot sequence in the System Setup.

NOTE: To locate the internal USB connector (INT_USB) on the system board, see System board

connectors.

Replacing the internal USB key

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. If applicable, remove the PCIe expansion-card riser

4. If applicable, remove the full length PCIe expansion card.

5. Remove the cooling shroud.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Locate the USB connector/USB key on the system board.

NOTE: To locate the internal USB connector on the system board, see System board

connectors.

2. If installed, remove the USB key.

3. Insert the new USB key into the USB connector.

Figure 25. Replacing the internal USB key

1. USB memory key 2. USB memory key connector

Next steps

1. If applicable, install the full length PCIe expansion card.

2. If applicable, install the PCIe expansion-card riser.

3. Reinstall the cooling shroud.

4. Follow the procedure listed in After working inside your system.

5. While booting, press <F2> to enter the System Setup and verify that the USB key is detected by the

system.

Related Links

Removing the (optional) expansion-card riser

Removing an expansion card from the expansion-card riser

Removing the cooling shroud

Installing an expansion card into the expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Expansion cards and expansion-card riser (optional)

NOTE: A missing or an unsupported expansion-card riser logs an SEL event. It does not prevent

your system from powering on and no BIOS POST message or F1/F2 pause is displayed.

Expansion-card installation guidelines

Your system supports PCI Express Generation 2 and Generation 3 expansion cards.

Use the following table as a guide for installing expansion cards to ensure proper cooling and mechanical

fit. The expansion cards with the highest priority must be installed first using the slot priority indicated. All

other expansion cards must be installed in card priority and slot priority order.

Table 4. Expansion card slots available on system board only

Location PCIe

slot Processor connection Height Length Link

width Slot

width

System board 1 Processor 2 Low

Profile

Half

Length

x8 x8

System board 2 Processor 1 Low

Profile

Half

Length

x16 x16

System board 3 Processor 1 Low

Profile

Half

Length

x16 x16

System board 4 Platform Controller Hub

(Mapped to Processor 1)

Low

Profile

Half

Length

x1 x1

System board 5 Platform Controller Hub

(Mapped to Processor 1)

Low

Profile

Half

Length

x4 x8

Table 5. Expansion card slots available on system board and optional expansion-card riser

Location PCIe

slot Processor connection Height Length Link

width Slot

width

Expansion-card riser 1 Processor 1 Full height Full

Length

x16 x16

Expansion-card riser 2 Processor 1 Full height Half

Length

x8 x8

System board 3 Processor 1 Low

Profile

Half

Length

x16 x16

System board 4 Platform Controller Hub

(Mapped to Processor 1)

Low

Profile

Half

Length

x1 x1

System board 5 Platform Controller Hub

(Mapped to Processor 1)

Low

Profile

Half

Length

x4 x8

NOTE: The optional expansion card riser is installed on PCIe slot 2 on the system board.

NOTE: When your system is installed with the optional expansion card riser in PCIe slot 2 on the

system board, you cannot install an expansion card in PCIe slot 1 of the system board.

NOTE: When x16 card installed in PCIe Slot 1 on expansion card riser the PCIe Slot 2 on the

expansion card will not function. The expansion card riser can be used only with two x8 PCIe cards

or with one x16 PCIe card on PCIE slot 1.

NOTE: Only slots 1, 2 and 3 support Generation 3 PCIe expansion cards.

NOTE: The expansion cards are not hot-swap.

Table 6. Expansion-card installation priority on system board only

Card Priority Category Slot Priority Max Allowed

1 GPU NA 0

2RAID Integrated storage Integrated Slot 1

RAID External storage 3,2,1 3

3 40G NICs 3,2,1 3

4 FC16 HBA 3,2,1 3

5 10Gb NICs 3,2,1,5 4

6 FC8 HBA 3,2,1,5 4

1Gb NICs (Broadcom Dual

Port)

3,2,1,5,4 5

1Gb NICs 3,2,1,5 4

8 Non-RAID 3,2,1 3

Table 7. Expansion-card installation priority on system board and optional expansion-card riser

Card Priority Category Slot Priority Max Allowed

1 GPU 1 1

2 RAID Integrated storage Integrated Slot 1

RAID External storage (Low

profile)

3 1

RAID External storage (Full

height)

2,1 2

440G NICs (Low profile) 3 1

40G NICs (Full height) 2,1 2

5FC16 HBA (Low profile) 3 1

FC16 HBA (Full height) 2,1 2

610Gb NICs (Low profile) 3,5 2

10Gb NICs (Full height) 2,1 2

7 FC8 HBA (Low profile) 3,5 2

FC8 HBA (Full height) 2,1 2

1Gb NICs (Low profile)

(Broadcom Dual Port)

3,5,4 3

1Gb NICs (Low profile) 3,5 2

Card Priority Category Slot Priority Max Allowed

1Gb NICs (Full height) 2,1 2

9Non-RAID (Low profile) 3 1

Non-RAID (Full height) 2,1 2

Removing an expansion card from the system board

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. If installed, disconnect the data / power cables from the expansion card.

2. Pull the expansion card retention latch lock and lift the latch up to open it.

3. Hold the expansion card by its edge, pull the card up to remove it from the expansion card

connector and out of the system.

4. If the expansion card is not going to be replaced, install a filler bracket by performing the following

steps:

a. Align the slot on the filler bracket with the tab on the expansion card slot.

b. Press the expansion card latch till the filler bracket locks into place.

NOTE: Filler brackets must be installed over empty expansion-card slots to maintain FCC

certification of the system. The brackets also keep dust and dirt out of the system and aid in

proper cooling and airflow inside the system.

1. expansion card retention latch lock 2. expansion card retention latch

3. expansion card 4. expansion card connector

Next steps

1. If applicable, connect the data / power cables to the expansion card.

2. Follow the procedure listed in After working inside your system.

Installing an expansion card on the system board

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Unpack the expansion card and prepare it for installation.

For instructions, see the documentation accompanying the card.

2. Open the expansion card retention latch.

3. If you are installing a new card, remove the filler bracket.

NOTE: Keep this bracket in case you need to remove the expansion card. Filler brackets must

be installed in empty expansion-card slots to maintain FCC certification of the system. The

brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside

the system.

4. Holding the card by its edges, position the card so that the card’s edge connector aligns with the

expansion card connector.

5. Insert the card’s edge connector firmly into the expansion card connector until the card is fully

seated.

6. Close the expansion card retention latch by pushing the latch down until the latch snaps into place.

7. Connect any cables to the expansion card.

Next steps

1. Install the expansion card holder.

2. Follow the procedure listed in After working inside your system.

Removing the (optional) expansion-card riser

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

Steps

Holding the touch points, lift the expansion-card riser from the riser connector on the system board.

Figure 26. Removing and installing the expansion card riser

1. expansion-card riser cage 2. riser guide on riser cage

3. riser guide on chassis

Next steps

1. If applicable, install an expansion card on the riser.

2. If applicable, reinstall the expansion-card riser.

3. Install the cooling shroud.

4. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Installing an expansion card into the expansion-card riser

Installing the cooling shroud

Installing the (optional) expansion-card riser

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. If applicable, reinstall the expansion card(s) into the expansion-card riser.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Align the expansion-card riser with the PCIe connector on the system board and the riser guides on

the system board and chassis.

2. Lower the expansion-card riser into place until the expansion-card riser is fully seated in the

connector.

Next steps

1. Follow the procedure listed in After working inside your system.

2. Install any device drivers required for the expansion-card as described in the documentation for the

card.

Related Links

Installing an expansion card into the expansion-card riser

Removing an expansion card from the expansion-card riser

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. Disconnect any cables connected to the expansion card.

5. Remove the expansion card riser out of the server.

Steps

1. Press the expansion-card retention latch down and turn the latch counterclockwise to open.

2. If you want to remove the expansion card permanently, install a metal filler bracket over the empty

expansion slot opening and close the expansion-card latch.

3. Close the expansion-card retention latch.

NOTE: You must install a filler bracket over an empty expansion slot to maintain Federal

Communications Commission (FCC) certification of the system. The brackets also keep dust

and dirt out of the system and aid in proper cooling and airflow inside the system.

Figure 27. Removing and installing an expansion card from the expansion-card riser

1. expansion-card riser 2. expansion-card riser cage

3. expansion-card retention latch 4. expansion card

Figure 28. Removing and installing a full height, full length expansion card from the expansion-card

riser

1. full height, full length expansion card

latch (on cooling shroud) 2. full height, full length expansion card

3. expansion card riser cage 4. expansion card retention latch

Next steps

1. If applicable, install an expansion card.

2. Install the expansion-card riser.

3. Install the cooling shroud.

4. If applicable, open the expansion-card latch on the cooling shroud to support a full length

expansion card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing an expansion card into the expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Installing an expansion card into the expansion-card riser

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable close the expansion-card latch on the cooling shroud to release the ful -

length card.

4. Remove the expansion-card riser.

5. Unpack the expansion card and prepare it for installation.

NOTE: For instructions, see the documentation accompanying the expansion card.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Press the expansion-card retention latch and rotate the latch clockwise.

2. Holding the card by its edges, position the card so that the card’s edge connector aligns with the

expansion card connector.

3. Insert the card’s edge connector firmly into the expansion card connector until the card is fully

seated.

4. Close the expansion-card retention latch.

5. If applicable, close the expansion-card latch on the cooling shroud.

Next steps

1. If applicable, install an expansion card.

2. Install the expansion-card riser.

3. If applicable, connect the required power or data cables to the expansion card.

4. Install the cooling shroud.

5. If applicable press the expansion-card latch on the cooling shroud to secure the expansion-card in

position

6. Follow the procedure listed in After working inside your system.

7. Install any device drivers required for the expansion-card as described in the documentation for the

card.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing an expansion card into the expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

iDRAC ports card (optional)

The iDRAC ports card consists of the SD vFlash card slot and an iDRAC port. The iDRAC ports card is used

for advanced management of the system.

An SD vFlash card is a Secure Digital (SD) card that plugs into the SD vFlash card slot in the system. It

provides persistent on-demand local storage and a custom deployment environment that allows

automation of server configuration, scripts, and imaging. It emulates USB device(s). For more information,

see the Integrated Dell Remote Access Controller User's Guide at dell.com/esmmanuals.

Removing the iDRAC ports card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full-

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. Remove the expansion-card riser.

6. Keep the #2 Phillips screwdriver ready.

Steps

1. Disconnect the management network cable from the iDRAC port.

2. Loosen the two screws securing the iDRAC ports card holder to the system board.

3. Pull the iDRAC ports card up and toward the front of the system to disengage it from the connector

and remove the card from the chassis.

Figure 29. Removing and installing the iDRAC ports card

1. iDRAC ports card holder 2. iDRAC port

3. SD vFlash media card reader 4. iDRAC ports card

5. screws (2) 6. iDRAC ports card connector on system

board

Next steps

1. Install the expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Install the cooling shroud.

4. If applicable, open the expansion-card latch on the cooling shroud to secure the full-length

expansion card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Installing the iDRAC ports card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full-

length card.

4. If applicable, disconnect the power or data cables from expansion-card (s).

5. If applicable, remove the expansion-card riser

Steps

1. Align and insert the tabs on the iDRAC ports card on the slots on the chassis wall.

2. Insert the iDRAC ports card into the connector on the system board.

3. Secure the iDRAC ports card using screws.

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable, open the expansion-card latch on the cooling shroud to secure the full-length

expansion-card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

SD vFlash media card

A vFlash SD card is a Secure Digital (SD) card that plugs into the vFlash SD card slot in the system. It

provides persistent on-demand local storage and a custom deployment environment that allows

automation of server configuration, scripts, and imaging. It emulates USB device(s). For more information,

see the Integrated Dell Remote Access Controller User’s Guide at dell.com/esmmanuals.

Replacing an SD vFlash media card

1. Locate the SD vFlash media slot at the back of the chassis.

2. To remove the SD vFlash media card, push the card inward to release it, and pull the card from the

card slot.

Figure 30. Removing and installing the SD vFlash media card

1. SD vFlash media card 2. SD vFlash media-card slot

3. To install an SD vFlash media card, insert the contact-pin end of the SD vFlash media card into the

card slot on the module.

NOTE: The slot is keyed to ensure correct insertion of the card.

4. Press the card inward to lock it into the slot.

Internal dual SD module

The Internal Dual SD Module (IDSDM) card provides two SD card slots. This card offers the following

features:

• Dual card operation — maintains a mirrored configuration using SD cards in both slots and provides

redundancy.

NOTE: When the Redundancy option is set to Mirror Mode in the Integrated Devices screen of

System Setup, the information is replicated from one SD card to another.

• Single card operation — single card operation is supported, but without redundancy.

Removing an internal SD card

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

Locate the SD card slot on the internal dual SD module and press the card to release it from the slot.

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card.

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Installing an internal SD card

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: To use an SD card with your system, ensure that the Internal SD Card Port is enabled in the

System Setup.

Steps

1. Locate the SD card connector on the internal dual SD module. Align the SD card appropriately and

insert the contact-pin end of the card into the slot.

NOTE: The slot is keyed to ensure correct insertion of the card.

2. Press the card into the card slot to lock it into place.

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Removing the internal dual SD module

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Locate the internal dual SD module on the system board.

2. If installed, remove the SD card(s).

3. Hold the plastic pull tab and pull the dual SD module out of the system board.

Figure 31. Removing and installing the Internal Dual SD Module (IDSDM)

1. Internal Dual SD module 2. LED status indicator (2)

3. SD card (2) 4. SD card slot 2

5. SD card slot 1 6. IDSDM connector

The following table describes the IDSDM indicator codes.

Convention IDSDM indicator code Condition

A Green Indicates that the card is online

B Flashing green Indicates rebuild or activity

C Flashing amber Indicates card mismatch or that the card has

failed

D Amber Indicates that the card is offline, has failed, or is

write protected

Convention IDSDM indicator code Condition

E Not lit Indicates that the card is missing or is booting

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Installing the internal dual SD module

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Locate the IDSDM connector on the system board.

2. Align the connectors on the system board and the dual SD module.

3. Push the dual SD module until it is firmly seated on the system board.

Next steps

1. Install the SD media card(s).

2. If applicable, install the PCIe expansion-card riser.

3. If applicable, connect the required power or data cables to the expansion card(s).

4. Reinstall the cooling shroud.

5. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

6. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing an internal SD card

Installing the (optional) expansion-card riser

Installing the cooling shroud

Integrated storage controller card

Your system supports an integrated storage controller card that provides the integrated storage

subsystem for your system’s internal hard drives. The controller supports SAS/SATA and SSD drives and

also enables you to set up the hard drives in RAID configurations as supported by the version of the

storage controller included with your system.

Removing the integrated storage controller card

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

6. Keep the #2 Phillips screwdriver ready.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Loosen the screws that secure the integrated storage controller cable to the integrated storage-

controller card connector on the system board.

2. Lift the integrated storage controller cable out and move it away from the integrated storage

controller card.

3. Lift one end of the card at an angle to disengage the card from the integrated storage-controller

card holder on system board.

4. Lift the card out of the chassis.

Figure 32. Removing and installing the integrated storage controller card

1. integrated storage controller cable 2. integrated storage controller card

3. integrated storage-controller card

connector on the system board 4. integrated storage controller card

holder

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Installing the integrated storage controller card

Prerequisites

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

6. Keep the #2 Phillips screwdriver ready.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Align the end of the integrated storage-controller card opposite the connector with the integrated

storage-controller card holder.

2. Lower the connector side of the integrated storage-controller card into the integrated storage-

controller card connector on the system board.

Ensure that the tabs on the system board align with the screw holes on the integrated storage-

controller card.

3. Align the screws on the integrated storage-controller card cable with the screw holes on the

connector.

4. Tighten the screws to secure the integrated storage-controller card cable with the integrated

storage-controller card connector on the system board.

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

5. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Processors

Use the following procedure when:

• Installing an additional processor

• Replacing a processor

NOTE: To ensure proper system cooling, you must install a processor blank in any empty processor

socket.

Removing a processor

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

NOTE: To ensure proper system cooling, you must install a processor blank in any empty processor

socket.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

6. Keep the #2 Phillips screwdriver ready.

7. If you are upgrading your system, download the latest system BIOS version from dell.com/support

and follow the instructions included in the compressed download file to install the update on your

system.

NOTE: You can update the system BIOS using the Lifecycle Controller.

WARNING: The heat sink and processor are hot to the touch for some time after the system has

been powered down. Allow the heat sink and processor to cool before handling them.

CAUTION: Never remove the heat sink from a processor unless you intend to remove the

processor. The heat sink is necessary to maintain proper thermal conditions.

Steps

1. To remove the heat sink:

a. Loosen one of the screws that secure the heat sink to the system board.

Wait 30 seconds for the heat sink to loosen from the processor.

b. Remove the screw diagonally opposite the screw you first removed.

c. Repeat the procedure for the remaining two screws.

d. Lift the heat sink out of the system.

Figure 33. Removing and installing a processor heat sink

1. captive screw (4) 2. heat sink

3. processor socket 4. slot (4)

CAUTION: The processor is held in its socket under strong pressure. Be aware that the

release lever can spring up suddenly if not grasped firmly.

Figure 34. Processor shield

1. close first socket release lever 2. lock icon

3. processor 4. open first socket release lever

5. unlock icon

2. To remove the processor:

a. Release the open first socket-lever near the unlock icon by pushing the lever down and out

from under the tab.

b. Similarly, release the close first socket-release lever near the lock icon by pushing the lever

down and out from under the tab. Lift the lever 90 degrees upward.

c. Lower the open first socket-release lever to lift the processor shield.

Figure 35. Removing and installing a processor

1. close first socket-release lever 2. pin-1 indicator of processor

3. processor 4. slot (4)

5. processor shield 6. open first socket-release lever

7. socket 8. socket keys (4)

d. Hold the tab on the processor shield and lift the processor shield until the open first socket-

release lever lifts up.

CAUTION: The socket pins are fragile and can be permanently damaged. Be careful not to

bend the pins in the socket when removing the processor out of the socket.

e. Lift the processor out of the socket and leave the open first socket-release lever up.

NOTE: If you are permanently removing the processor, you must install a socket protective

cap in the vacant socket to protect the socket pins and keep the socket free of dust.

NOTE: After removing the processor, place it in an anti-static container for reuse, return, or

temporary storage. Do not touch the bottom of the processor. Touch only the side edges of

the processor.

Next steps

1. Replace the heat sink(s) and processor(s).

2. If applicable, install the PCIe expansion-card riser.

3. If applicable, connect the required power or data cables to the expansion card(s).

4. Reinstall the cooling shroud.

5. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

6. Follow the procedure listed in After working inside your system.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing a processor

Installing the (optional) expansion-card riser

Installing the cooling shroud

Installing a processor

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

6. Keep the #2 Phillips screwdriver ready.

7. If you are upgrading your system, download the latest system BIOS version from dell.com/support

and follow the instructions included in the compressed download file to install the update on your

system.

NOTE: You can update the system BIOS using the Lifecycle Controller.

CAUTION: Never remove the heat sink from a processor unless you intend to remove the

processor. The heat sink is necessary to maintain proper thermal conditions.

NOTE: If you are installing a single processor, it must be installed in socket CPU1.

Steps

1. Remove the heat sink.

2. Unpack the new processor.

If the processor has previously been used in a system, remove any remaining thermal grease from

the processor using a lint-free cloth.

3. Locate the processor socket.

4. If applicable, remove the socket protective cap.

5. Release the open first socket-release lever near the unlock icon by pushing the lever down and

out from under the tab.

6. Similarly, release the close first socket-release lever near the lock icon by pushing the lever down

and out from under the tab. Lift the lever 90 degrees upward.

7. Hold the tab near the lock symbol on the processor shield and lift it up and out of the way.

8. To install the processor in the socket:

CAUTION: Positioning the processor incorrectly can permanently damage the system board

or the processor. Be careful not to bend the pins in the socket.

CAUTION: While removing or reinstalling the processor, wipe your hands of any

contaminants. Contaminants on the processor pins such as thermal grease or oil can damage

the processor.

a. Align the processor with the socket keys.

CAUTION: Do not use force to seat the processor. When the processor is positioned

correctly, it engages easily into the socket.

b. Align the pin-1 indicator of the processor with the triangle on the socket.

c. Place the processor on the socket such that the slots on the processor align with the socket keys.

CAUTION: Do not use force to seat the processor. When the processor is positioned

correctly, it engages easily into the socket.

d. Close the processor shield.

e. Lower the close first socket-release lever near the lock icon and push it under the tab to lock

it.

f. Similarly, lower the open first socket-release lever near the unlock icon and push it under the

tab to lock it.

9. To install the heat sink:

a. If applicable, remove the existing thermal grease from the heat sink using a clean lint-free cloth.

b. Apply thermal grease on the top of the processor. Use the thermal-grease syringe included with

your processor kit to apply the grease in a thin spiral on the top of the processor as shown in the

figure.

CAUTION: Applying too much thermal grease can result in excess grease coming in

contact with and contaminating the processor socket.

Figure 36. Applying thermal grease on the top of the processor

1. processor 2. thermal grease

3. thermal-grease syringe

NOTE: The thermal-grease is intended for one-time use only. Dispose of the syringe after

you use it.

c. Place the heat sink onto the processor.

d. Tighten the four screws to secure the heat sink to the system board.

NOTE: Tighten the screws diagonally opposite to each other. Do not over-tighten the heat

sink retention screws when installing the heat sink. To prevent over-tightening, tighten the

retention screw until resistance is felt, and stop once the screw is seated. The screw tension

should be no more than 6 in-lb (6.9 kg-cm).

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

5. Follow the procedure listed in After working inside your system.

6. While booting, press <F2> to enter the System Setup and check that the processor information

matches the new system configuration.

7. Run the system diagnostics to verify that the new processor operates correctly.

Related Links

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Power supplies

Your system supports:

• Two 495 W, 750 W, or 1100 W AC power supply modules

• One cabled 450 W power supply module (non-redundant)

• Two 750 W DC power supply modules

– When two identical power supplies are installed, the power supply configuration is redundant (1 +

1). In redundant mode, power is supplied to the system equally from both power supplies to

maximize efficiency.

– When only one power supply is installed, the power supply configuration is non-redundant (1 + 0).

Power is supplied to the system only by the single power supply.

– When configured in a 2+0 configuration, 1+1 redundancy will not be supported.

NOTE: If two power supplies are used, they must be of the same type and must have the same

maximum output power.

Hot Spare feature

Your system supports the Hot Spare feature that significantly reduces the power overhead associated

with power supply redundancy.

When the Hot Spare feature is enabled, one of the redundant power supplies is switched to a sleep state.

The active power supply supports 100% of the load, thus operating at higher efficiency. The power supply

in the sleep state monitors output voltage of the active power supply. If the output voltage of the active

power supply drops, the power supply in the sleep state returns to an active output state.

If having both power supplies active is more efficient than having one power supply in a sleep state, the

active power supply can also activate a sleeping power supply.

The default power supply settings are as follows:

• If the load on the active power supply is more than 50%, then the redundant power supply is switched

to the active state.

• If the load on the active power supply falls below 20%, then the redundant power supply is switched

to the sleep state

You can configure the Hot Spare feature using the iDRAC settings. For more information on iDRAC

settings, see the Integrated Dell Remote Access Controller User’s Guide at dell.com/support/home.

Removing the power supply unit blank

If you are installing a second power supply unit, remove the power supply unit blank in the bay by

pulling the blank outward.

100

CAUTION: To ensure proper system cooling, the power supply blank must be installed in the

second power supply bay in a non-redundant configuration. Remove the power supply blank

only if you are installing a second power supply.

Figure 37. Removing and installing the power supply blank

1. power supply blank 2. power supply bay

Installing the power supply unit blank

Install the power supply unit blank only in the second power supply unit bay.

To install the power supply unit blank, align the blank with the power supply unit bay and push it into

the chassis until it clicks into place.

Removing an AC power supply unit

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: The system requires one power supply for normal operation. On power-redundant

systems, remove and replace only one power supply at a time in a system that is powered on.

NOTE: You may have to unlatch and lift the optional cable management arm if it interferes with

power supply removal. For information about the cable management arm, see the system’s rack

documentation.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

101

Steps

1. Disconnect the power cable from the power source and from the power supply unit you intend to

remove and remove the cables from the strap.

2. Press the release latch and slide the power supply unit out of the chassis.

Figure 38. Removing and installing an AC power supply unit

1. release latch 2. power supply unit cable connector

3. power supply unit 4. connector

5. power supply unit handle

Next steps

1. Install the AC power supply unit.

2. Follow the procedure listed in After working inside your system.

Related Links

Installing an AC power supply unit

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

Steps

1. Verify that both the power supply units are the same type and have the same maximum output

power.

102

NOTE: The maximum output power (shown in watts) is listed on the power supply label.

2. If applicable, remove the power supply unit blank.

3. Slide the new power supply unit into the chassis until the power supply unit is fully seated and the

release latch snaps into place.

NOTE: If you unlatched the cable management arm, re-latch it. For information about the cable

management arm, see the system’s rack documentation.

4. Connect the power cable to the power supply unit and plug the cable into a power outlet.

CAUTION: When connecting the power cable, secure the cable with the strap.

NOTE: When installing, hot-swapping, or hot-adding a new power supply unit, wait for 15

seconds for the system to recognize the power supply unit and determine its status. The power

supply redundancy may not occur until discovery is complete. Wait until the new power supply

unit is discovered and enabled before you remove the other power supply unit. The power-

supply unit status indicator turns green to signify that the power supply unit is functioning

properly.

Non-redundant AC power supply (cabled)

Your system supports a cabled non-redundant 450 W AC power supply.

NOTE: When selecting or upgrading your system configuration, verify the system power

consumption with the Dell Energy Smart Solution Advisor at dell.com/ESSA to ensure optimum

power utilization.

Removing a non-redundant AC power supply (cabled)

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

6. Keep the #2 Phillips screwdriver ready.

Steps

1. Disconnect the power cable from the power source.

2. Disconnect the power cable from the power supply and remove the power cables from the cable

strap.

3. Disconnect all the power cables from the power supply to the system board and hard-drive

backplane.

4. Remove the screw securing the power supply to the chassis and slide the power supply out of the

power supply unit cage.

103

Figure 39. Removing and installing a non-redundant AC power supply (cabled)

1. screw 2. power supply unit cage

3. non-redundant power supply 4. standoff on the chassis

5. P1 cable connector 6. P2 cable connector

7. P3 cable connector 8. backplane connector

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

5. Connect the power cable to the back of the power supply unit and secure the power cables to the

cable strap.

6. Reconnect the power cable to the power source.

7. Follow the procedure listed in After working inside your system.

Related Links

104

Removing the cooling shroud

Removing the (optional) expansion-card riser

Installing the (optional) expansion-card riser

Installing the cooling shroud

Installing a non-redundant AC power supply (cabled)

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Ensure that you read the Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the cooling shroud.

NOTE: If applicable, close the expansion-card latch on the cooling shroud to release the full

length card.

4. If applicable, disconnect the power or data cables from expansion card (s).

5. If applicable, remove the expansion-card riser

6. Keep the #2 Phillips screwdriver ready.

Steps

1. Unpack the new power supply.

2. Slide the new power supply into the power supply unit cage until the power supply is fully seated.

3. Tighten the screw to secure the power supply to the chassis.

4. Connect all the power cables to the system board and hard-drive backplane.

Next steps

1. If applicable, install the PCIe expansion-card riser.

2. If applicable, connect the required power or data cables to the expansion card(s).

3. Reinstall the cooling shroud.

4. If applicable open the expansion-card latch on the cooling shroud to secure the full length

expansion card.

5. Follow the procedure listed in After working inside your system.

Wiring instructions for a DC power supply unit

Your system supports up to two –(48–60) V DC power supplies (when available).

WARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must

perform all connections to DC power and to safety grounds. Do not attempt connecting to DC

power or installing grounds yourself. All electrical wiring must comply with applicable local or

national codes and practices. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow all safety instructions that came with the product.

CAUTION: Wire the unit with copper only, unless otherwise specified, use only 10 American Wire

Gauge (AWG) wire rated minimum 90 ºC for source and return. Protect the –(48–60) V DC (1

wire) with a branch circuit over-current protection rated 50 A for DC with a high interrupt

current rating.

105

CAUTION: Connect the equipment to a –(48–60) V DC supply source that is electrically isolated

from the AC source (reliably grounded –(48–60) V DC SELV source). Ensure that the –(48–60) V

DC source is efficiently secured to earth (ground).

NOTE: A readily accessible disconnect device that is suitably approved and rated shall be

incorporated in the field wiring.

Input requirements

• Supply voltage: –(48–60) V DC

• Current consumption: 32 A (maximum)

Kit contents

• Dell part number 6RYJ9 terminal block or equivalent (1)

• #6-32 nut equipped with lock washer (1)

Required tools

Wire-stripper pliers capable of removing insulation from size 10 AWG solid or stranded, insulated copper

wire

NOTE: Use alpha wire part number 3080 or equivalent (65/30 stranding)

Required wires

• One UL 10 AWG, 2 m maximum (stranded) black wire [–(48–60) V DC]

• One UL 10 AWG, 2 m maximum (stranded) red wire (V DC return)

• One UL 10 AWG, 2 m maximum green/yellow, green with a yellow stripe, stranded wire (safety

ground)

Assembling and connecting the safety ground wire

Prerequisites

WARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must

perform all connections to DC power and to safety grounds. Do not attempt connecting to DC

power or installing grounds yourself. All electrical wiring must comply with applicable local or

national codes and practices. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow all safety instructions that came with the product.

Steps

1. Strip the insulation from the end of the green/yellow wire, exposing approximately 4.5 mm (0.175

inch) of copper wire.

2. Using a hand-crimping tool (Tyco Electronics, 58433-3 or equivalent), crimp the ring-tongue

terminal (Jeeson Terminals Inc., R5-4SA or equivalent) to the green/yellow wire (safety ground wire).

3. Connect the safety ground wire to the grounding post on the back of the system using a #6-32 nut

equipped with a locking washer.

106

Figure 40. Assembling and connecting the safety ground wire

1. #6-32 nut 2. spring washer

3. locking washer 4. safety ground wire

5. grounding post

Assembling the DC input power wires

Prerequisites

WARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must

perform all connections to DC power and to safety grounds. Do not attempt connecting to DC

power or installing grounds yourself. All electrical wiring must comply with applicable local or

national codes and practices. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow all safety instructions that came with the product.

Steps

1. Strip the insulation from the ends of the DC power wires, exposing approximately 13 mm (0.5 inch)

of copper wire.

WARNING: Reversing polarity when connecting DC power wires can permanently damage

the power supply or the system.

2. Insert the copper ends into the mating connectors and tighten the captive screws at the top of the

mating connector using a #2 Phillips screwdriver.

WARNING: To protect the power supply from electrostatic discharge, the captive screws

must be covered with the rubber cap before inserting the mating connector into the power

supply.

3. Rotate the rubber cap clockwise to fix it over the captive screws.

4. Insert the mating connector into the power supply.

107

Figure 41. Assembling the DC input power wires

1. wire RTN 2. DC power connector

3. captive screws (2) 4. rubber cap

5. DC power socket 6. wire –48 V

Removing a DC power supply unit