Dell PowerEdge R630 Owner's Manual
Dell PowerEdge R630 system overview
Documentation resources
Technical specifications
Initial system setup and configuration
Pre-operating system management applications
Installing and removing system components
Using system diagnostics
- Dell Embedded System Diagnostics
Jumpers and connectors
Troubleshooting your system
Getting help

DELL R630 User Manual

Displayed below is the user manual for R630 by DELL which is a product in the Servers category. This manual has pages.

Related Manuals

DELL R630+770-BBJR Manual

DELL R630+Windows Server 2016 Standard Manual

DELL R630+Windows Server 2016 Essentials Manual

DELL R630 Manual

Dell PowerEdge R630

Owner's Manual

Regulatory Model: E26S Series

Regulatory Type: E26S001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

property laws. Dell and the Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other

marks and names mentioned herein may be trademarks of their respective companies.

2016 - 03

Rev. A03

Contents

1 Dell PowerEdge R630 system overview........................................................... 9

Supported configurations for the PowerEdge R630 system...............................................................9

Front panel...........................................................................................................................................10

10 x 2.5-inch hard drive chassis.................................................................................................... 11

Eight x 2.5-inch hard drive chassis................................................................................................13

24 x 1.8-inch hard drive chassis....................................................................................................15

LCD panel.......................................................................................................................................17

Back panel............................................................................................................................................19

Two-riser chassis...........................................................................................................................19

Three-riser chassis.........................................................................................................................21

Diagnostic indicators.......................................................................................................................... 23

Hard drive indicator codes............................................................................................................25

uSATA SSD indicator codes.......................................................................................................... 26

NIC indicator codes.......................................................................................................................27

Power supply unit indicator codes............................................................................................... 27

iDRAC Direct LED indicator codes............................................................................................... 30

Quick Sync indicator codes.......................................................................................................... 32

Locating Service Tag of your system................................................................................................. 33

2 Documentation resources................................................................................ 34

3 Technical specifications.................................................................................... 37

Chassis dimensions............................................................................................................................. 37

Chassis weight.....................................................................................................................................38

Processor specifications..................................................................................................................... 38

PSU specifications...............................................................................................................................38

System battery specifications............................................................................................................. 39

Expansion bus specifications..............................................................................................................39

Memory specifications........................................................................................................................39

Drive specifications.............................................................................................................................40

Hard drives.................................................................................................................................... 40

Optical drive.................................................................................................................................. 40

Ports and connectors specifications..................................................................................................40

USB ports.......................................................................................................................................40

NIC ports........................................................................................................................................41

Serial connector.............................................................................................................................41

VGA ports.......................................................................................................................................41

Internal Dual SD Module............................................................................................................... 41

Video specifications.............................................................................................................................41

Environmental specifications..............................................................................................................41

Particulate and gaseous contamination specifications............................................................... 43

Standard operating temperature..................................................................................................44

Expanded operating temperature................................................................................................ 44

Expanded operating temperature restrictions............................................................................. 45

4 Initial system setup and configuration...........................................................46

Setting up your system....................................................................................................................... 46

iDRAC configuration...........................................................................................................................46

Options to set up iDRAC IP address.............................................................................................46

Options to install the operating system............................................................................................. 47

Methods to download firmware and drivers................................................................................47

5 Pre-operating system management applications........................................49

Options to manage the pre-operating system applications.............................................................49

System Setup.......................................................................................................................................49

Viewing System Setup...................................................................................................................50

System Setup details..................................................................................................................... 50

System BIOS.................................................................................................................................. 50

iDRAC Settings utility.....................................................................................................................74

Device Settings.............................................................................................................................. 74

Dell Lifecycle Controller..................................................................................................................... 75

Embedded system management..................................................................................................75

Boot Manager...................................................................................................................................... 75

Viewing Boot Manager.................................................................................................................. 75

Boot Manager main menu............................................................................................................ 76

PXE boot.............................................................................................................................................. 76

6 Installing and removing system components............................................... 77

Safety instructions............................................................................................................................... 77

Before working inside your system.....................................................................................................77

After working inside your system....................................................................................................... 78

Recommended tools.......................................................................................................................... 78

Front bezel (optional)..........................................................................................................................78

Removing the optional front bezel...............................................................................................78

Installing the optional front bezel................................................................................................ 80

System cover....................................................................................................................................... 81

Removing the system cover..........................................................................................................81

Installing the system cover........................................................................................................... 82

Inside the system................................................................................................................................ 83

Cooling shroud................................................................................................................................... 86

Removing the cooling shroud......................................................................................................86

Installing the cooling shroud........................................................................................................ 87

System memory.................................................................................................................................. 87

General memory module installation guidelines.........................................................................89

Mode-specific guidelines............................................................................................................. 90

Sample memory configurations....................................................................................................91

Removing memory modules........................................................................................................94

Installing memory modules.......................................................................................................... 95

Hard drives...........................................................................................................................................97

Removing a 2.5-inch hard drive blank..........................................................................................97

Installing a 2.5-inch hard drive blank........................................................................................... 98

Removing a 1.8-inch hard drive blank......................................................................................... 99

Installing a 1.8-inch hard drive blank........................................................................................... 99

Removing a hot swappable hard drive or SSD...........................................................................100

Installing a hot swappable hard drive.........................................................................................102

Removing a hard drive from a hard drive carrier....................................................................... 103

Installing a hot swappable hard drive into a hot swappable hard drive carrier........................104

Removing a 1.8-inch hard drive from a hard drive carrier........................................................ 105

Installing a 1.8-inch hard drive into a hard drive carrier............................................................106

Optical drive (optional)..................................................................................................................... 106

Removing the optional optical drive.......................................................................................... 106

Installing the optional optical drive............................................................................................ 107

Removing the slim optical drive blank....................................................................................... 108

Installing the slim optical drive blank......................................................................................... 109

Cooling fans.......................................................................................................................................110

Removing a cooling fan.............................................................................................................. 110

Installing a cooling fan.................................................................................................................111

Internal USB memory key (optional).................................................................................................112

Replacing the optional internal USB memory key......................................................................112

Expansion cards and expansion card riser....................................................................................... 114

Expansion card installation guidelines........................................................................................114

Removing expansion card risers................................................................................................. 115

Removing an expansion card...................................................................................................... 117

Installing an expansion card........................................................................................................118

Installing expansion card risers................................................................................................... 119

SD vFlash media card (optional)........................................................................................................121

Replacing an SD vFlash card........................................................................................................121

Internal dual SD module (optional)...................................................................................................122

Removing an internal SD Card....................................................................................................122

Installing an internal SD card...................................................................................................... 123

Removing the optional internal dual SD module.......................................................................123

Installing the optional internal dual SD module ........................................................................125

Integrated storage controller card....................................................................................................127

Removing the integrated storage controller card......................................................................127

Installing the integrated storage controller card....................................................................... 129

Network daughter card..................................................................................................................... 131

Removing the network daughter card........................................................................................131

Installing the network daughter card..........................................................................................132

Processors and heat sinks.................................................................................................................134

Removing a heat sink.................................................................................................................. 134

Removing a processor.................................................................................................................135

Installing a processor.................................................................................................................. 139

Installing a heat sink....................................................................................................................140

Power supply units............................................................................................................................142

Hot spare feature.........................................................................................................................143

Removing the power supply unit blank......................................................................................143

Installing the power supply unit blank........................................................................................144

Removing an AC power supply unit........................................................................................... 145

Installing an AC power supply unit.............................................................................................146

Wiring instructions for a DC power supply unit......................................................................... 147

Removing a DC power supply unit.............................................................................................150

Installing a DC power supply unit............................................................................................... 151

System battery...................................................................................................................................152

Replacing the system battery......................................................................................................152

Hard drive backplane........................................................................................................................ 154

Removing the hard drive backplane...........................................................................................154

Installing the hard drive backplane............................................................................................. 161

Control panel assembly.................................................................................................................... 163

Removing the control panel board–eight hard drive system................................................... 163

Installing the control panel board–eight hard drive system..................................................... 164

Removing the control panel–eight hard drive system.............................................................. 165

Installing the control panel–eight hard drive system................................................................ 167

Removing the control panel–10 hard drive and 24 hard drive system.................................... 168

Installing the control panel–10 hard drive system and 24 hard drive system..........................169

VGA module.......................................................................................................................................171

Removing the VGA module.........................................................................................................171

Installing the VGA module...........................................................................................................172

System board.....................................................................................................................................174

Removing the system board....................................................................................................... 174

Installing the system board..........................................................................................................177

Trusted Platform Module..................................................................................................................180

Installing the Trusted Platform Module......................................................................................180

Initializing the TPM for BitLocker users...................................................................................... 181

Initializing the TPM for TXT users............................................................................................... 182

7 Using system diagnostics................................................................................183

Dell Embedded System Diagnostics.................................................................................................183

Running the Embedded System Diagnostics from Boot Manager............................................183

Running the Embedded System Diagnostics from the Dell Lifecycle Controller.....................183

System diagnostics controls.......................................................................................................184

8 Jumpers and connectors ............................................................................... 185

System board jumper settings.......................................................................................................... 185

System board jumpers and connectors...........................................................................................186

Disabling a forgotten password........................................................................................................188

9 Troubleshooting your system........................................................................189

Safety first — for you and your system.............................................................................................189

Troubleshooting system startup failure........................................................................................... 189

Troubleshooting external connections............................................................................................189

Troubleshooting the video subsystem.............................................................................................189

Troubleshooting a USB device......................................................................................................... 190

Troubleshooting iDRAC Direct (USB XML configuration)................................................................191

Troubleshooting iDRAC Direct (Laptop connection).......................................................................191

Troubleshooting a serial I/O device................................................................................................. 192

Troubleshooting a NIC......................................................................................................................192

Troubleshooting a wet system......................................................................................................... 193

Troubleshooting a damaged system................................................................................................194

Troubleshooting the system battery................................................................................................ 195

Troubleshooting power supply units................................................................................................195

Troubleshooting power source problems................................................................................. 196

Power supply unit problems.......................................................................................................196

Troubleshooting cooling problems................................................................................................. 196

Troubleshooting cooling fans...........................................................................................................197

Troubleshooting system memory....................................................................................................198

Troubleshooting an internal USB key...............................................................................................199

Troubleshooting an SD card.............................................................................................................199

Troubleshooting an optical drive.....................................................................................................200

Troubleshooting a tape backup unit................................................................................................ 201

Troubleshooting a hard drive...........................................................................................................202

Troubleshooting a storage controller..............................................................................................202

Troubleshooting expansion cards................................................................................................... 203

Troubleshooting processors............................................................................................................204

10 Getting help.................................................................................................... 206

Contacting Dell.................................................................................................................................206

Documentation feedback................................................................................................................ 206

Accessing system information by using QRL.................................................................................. 206

Quick Resource Locator for R630............................................................................................. 207

Dell PowerEdge R630 system overview

The Dell PowerEdge R630 rack servers support up to:

• Two Intel Xeon E5-2600 v3 or v4 processors

• 24 x 1.8-inch hard drives or 10 x 2.5-inch hard drives or eight x 2.5-inch hard drives

• Four optional NVMe Express Flash PCIe SSDs

• 24 DIMM slots supporting up to 1536 GB of memory

• Two AC or DC redundant power supply units

NOTE: The Dell PowerEdge R630 system supports hot swappable hard drives.

Supported configurations for the PowerEdge R630

system

The Dell PowerEdge R630 system supports the following configurations:

Figure 1. Supported configurations for the PowerEdge R630 system

Front panel

10 x 2.5-inch hard drive chassis

Figure 2. Front panel features of the 10 x 2.5-inch hard drive PowerEdge R630 chassis

1. Diagnostic indicators 2. System health indicator

3. Power-on indicator, power button 4. NMI button

5. System identification button 6. Micro USB port/iDRAC Direct

7. Information tag 8. Hard drives (10)

9. Quick Sync

Table 1. Front panel features of the 10 x 2.5-inch hard drive PowerEdge R630 chassis

Item Indicator, Button, or

Connector Icon Description

1 Diagnostic indicators The diagnostic indicators light up to display error

status.

2 System health indicator The system health indicator flashes amber when a

system fault is detected.

3 Power-on indicator,

power button

The power indicator turns on when the system

power is on. The power button controls the power

supply output to the system.

NOTE: On ACPI-compliant operating systems,

turning off the system by using the power

button causes the system to perform a

graceful shutdown before power to the

system is turned off.

4 NMI button Used to troubleshoot software and device driver

errors when running certain operating systems.

This button can be pressed by using the end of a

paper clip.

Item Indicator, Button, or

Connector Icon Description

NOTE: Use this button only if directed to do

so by qualified support personnel or by the

operating system documentation.

5 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pressed, the system status indicator on the back

flashes until one of the buttons is pressed again.

Press to toggle the system ID on or off.

If the system stops responding during POST, press

and hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC

setup), press and hold the button for more than 15

seconds.

6 Micro USB port/iDRAC

Direct

Enables you to connect USB devices to the system

or provides access to the iDRAC Direct features.

For more information, see the Integrated Dell

Remote Access Controller User's Guide at

Dell.com/idracmanuals. The port is USB 3.0-

compliant.

7 Information tag Contains system information such as service tag,

NIC, MAC address for your reference. The

information tag is a slide-out label panel.

8 Hard drives (10) Up to ten 2.5-inch hot swappable hard drives. Up

to six 2.5-inch hot swappable hard drives and up to

four 2.5-inch Dell PowerEdge Express Flash

devices (PCIe SSDs).

9 Quick Sync Indicates a Quick Sync enabled system. The Quick

Sync feature is optional and needs a Quick Sync

bezel. This feature allows management of the

system by using mobile devices. This feature

aggregates hardware or firmware inventory and

various system level diagnostic and error

information that can be used in troubleshooting

the system. For more information, see the

Integrated Dell Remote Access Controller User’s

Guide at Dell.com/idracmanuals.

Eight x 2.5-inch hard drive chassis

Figure 3. Front panel features of the eight x 2.5-inch PowerEdge R630 hard drive chassis

1. Power-on indicator, power button 2. NMI button

3. System identification button 4. USB management port or iDRAC Direct (2)

5. Optical drive (optional) 6. SD vFlash media card slot

7. LCD menu buttons 8. Information tag

9. LCD panel 10. Video connector

11. Hard drives (8) 12. Quick Sync

Table 2. Front panel features of the eight x 2.5-inch PowerEdge R630 hard drive chassis

Item Indicator, Button, or

Connector Icon Description

1 Power-on indicator,

power button

Enables you to know the power status of the

system. The power indicator turns on when the

system power is on. The power button controls

the power supply output to the system.

NOTE: On Advanced Configuration and

Power Interface (ACPI)-compliant operating

systems, turning off the system by using the

power button causes the system to perform a

graceful shutdown before power to the

system is turned off.

2 NMI button Enables you to troubleshoot software and device

driver errors when running certain operating

systems. This button can be pressed by using the

end of a paper clip.

NOTE: Use this button only if directed to do

so by qualified support personnel or by the

operating system documentation.

3 System identification

button

Enables you to locate a particular system within a

rack. The identification buttons are on the front

and back panels. When one of these buttons is

pressed, the LCD panel on the front and the

Item Indicator, Button, or

Connector Icon Description

system status indicator on the back flash until one

of the buttons is pressed again.

To turn the system ID on or off, press the system

identification button.

If the system stops responding during POST, press

and hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC

setup), press and hold the button for more than 15

seconds.

4 USB management port/

iDRAC Direct (2)

Functions as a regular USB port or provides access

to the iDRAC Direct features. For more

information, see the iDRAC Guide at Dell.com/

idracmanuals.

The ports are USB 3.0-compliant.

5 Optical drive (optional) One optional SATA DVD-ROM drive or DVD+/-RW

drive.

NOTE: DVD devices are data only.

6 SD vFlash media card

slot

Enables you to insert a vFlash media card.

7 LCD menu buttons Enables you to navigate the control panel LCD

menu.

8 Information tag Contains system information such as service tag,

NIC, MAC address for your reference. The

information tag is a slide-out label panel.

9 LCD panel Displays system ID, status information, and system

error messages. The LCD turns blue during normal

system operation. When the system needs

attention, the LCD turns amber and the LCD panel

displays an error code followed by descriptive text.

NOTE: If the system is connected to AC

power and an error is detected, the LCD turns

amber regardless of whether the system is

turned on or off.

10 Video connector Enables you to connect a VGA display to the

system.

11 Hard drives (8) Up to eight 2.5-inch hot swappable hard drives.

12. Quick Sync Indicates a Quick Sync enabled system. The Quick

Sync feature is optional and needs a Quick Sync

Item Indicator, Button, or

Connector Icon Description

bezel. This feature allows management of the

system by using mobile devices. This feature

aggregates hardware or firmware inventory and

various system level diagnostic and error

information that can be used in troubleshooting

the system. For more information, see the

Integrated Dell Remote Access Controller User’s

Guide at Dell.com/idracmanuals.

24 x 1.8-inch hard drive chassis

Figure 4. Front panel features of the 24 x 1.8-inch hard drive PowerEdge R630 chassis

1. Diagnostic indicators 2. System health indicator

3. Power-on indicator, power button 4. NMI button

5. System identification button 6. Micro USB port

7. Information tag 8. Hard drives (24)

9. Quick Sync

Table 3. Front panel features of the 24 x 1.8-inch hard drive PowerEdge R630 chassis

Item Indicator, Button, or

Connector Icon Description

1 Diagnostic indicators The diagnostic indicators light up to display error

status.

2 System health indicator The system health indicator flashes amber when a

system fault is detected.

3 Power-on indicator,

power button

The power indicator turns on when the system

power is on. The power button controls the

power supply output to the system.

Item Indicator, Button, or

Connector Icon Description

NOTE: On ACPI-compliant operating

systems, turning off the system by using the

power button causes the system to perform

a graceful shutdown before power to the

system is turned off.

4 NMI button Used to troubleshoot software and device driver

errors when running certain operating systems.

This button can be pressed by using the end of a

paper clip.

NOTE: Use this button only if directed to do

so by qualified support personnel or by the

operating system documentation.

5 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pressed, the system status indicator on the back

flashes until one of the buttons is pressed again.

Press to toggle the system ID on or off.

If the system stops responding during POST, press

and hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset the iDRAC (if not disabled in F2 iDRAC

setup), press and hold the button for more than

15 seconds.

6 Micro USB port Enables you to connect USB devices to the

system or provides access to the iDRAC Direct

features. For more information, see the Integrated

Dell Remote Access Controller User's Guide at

Dell.com/idracmanuals. The port is USB 3.0-

compliant.

7 Information tag Contains system information such as service tag,

NIC, MAC address for your reference. The

information tag is a slide-out label panel.

8 Hard drives (24) Up to twenty four 1.8-inch hot swappable hard

drives.

9 Quick Sync Indicates a Quick Sync enabled system. The

Quick Sync feature is optional and needs a Quick

Sync bezel. This feature allows management of

the system by using mobile devices. This feature

aggregates hardware or firmware inventory and

various system level diagnostic and error

information that can be used in troubleshooting

the system. For more information, see the

Item Indicator, Button, or

Connector Icon Description

Integrated Dell Remote Access Controller User’s

Guide at Dell.com/idracmanuals.

LCD panel

The LCD panel of your system provides system information, status, and error messages to indicate if the

system is functioning correctly or if the system needs attention. For more information about error

messages, see the Dell Event and Error Messages Reference Guide at Dell.com/

openmanagemanuals >OpenManage software.

• The LCD backlight turns blue during normal operating conditions.

• When the system needs attention, the LCD turns amber, and displays an error code followed by

descriptive text.

NOTE: If the system is connected to a power source and an error is detected, the LCD turns

amber regardless of whether the system is turned on or off.

• The LCD backlight is turned off when the system is in standby mode and can be turned on by pressing

either the Select, Left, or Right button on the LCD panel.

• The LCD backlight remains off if LCD messaging is turned off using the iDRAC utility, the LCD panel,

or other tools.

Figure 5. LCD panel features

Table 4. LCD panel features

Item Button Description

1 Left Moves the cursor back in one-step increments.

2 Select Selects the menu item highlighted by the cursor.

3 Right Moves the cursor forward in one-step increments.

During message scrolling:

• Press and hold the button to increase scrolling speed.

• Release the button to stop.

NOTE: The display stops scrolling when the button is

released. After 45 seconds of inactivity the display starts

scrolling.

Viewing Home screen

About this task

The Home screen displays user-configurable information about the system. This screen is displayed

during normal system operation when there are no status messages or errors. When the system is in

standby mode, the LCD backlight turns off after a few minutes of inactivity, if there are no error

messages.

Steps

1. To view the Home screen, press one of the three navigation buttons (Select, Left, or Right).

2. To navigate to the Home screen from another menu, complete the following steps:

a. Press and hold the up arrow until the Home icon is displayed.

b. Select the Home icon.

c. On the Home screen, press the Select button to enter the main menu.

Setup menu

NOTE: When you select an option in the Setup menu, you must confirm the option before

proceeding to the next action.

Option Description

iDRAC Select DHCP or Static IP to configure the network mode. If Static IP is selected,

the available fields are IP, Subnet (Sub), and Gateway (Gtw). Select Setup DNS to

enable DNS and to view domain addresses. Two separate DNS entries are available.

Set error Select SEL to view LCD error messages in a format that matches the IPMI

description in the SEL. This enables you to match an LCD message with an SEL

entry.

Select Simple to view LCD error messages in a simplified user-friendly description.

For more information about error messages, see the Dell Event and Error Messages

Reference Guide at Dell.com/openmanagemanuals > OpenManage software.

Set home Select the default information to be displayed on the Home screen. See View menu

section for the options and option items that can be set as the default on the

Home screen.

Related Links

View menu

NOTE: When you select an option in the View menu, you must confirm the option before

proceeding to the next action.

Option Description

iDRAC IP Displays the IPv4 or IPv6 addresses for iDRAC8. Addresses include DNS (Primary

and Secondary), Gateway, IP, and Subnet (IPv6 does not have Subnet).

MAC Displays the MAC addresses for iDRAC, iSCSI, or Network devices.

Name Displays the name of the Host, Model, or User String for the system.

Number Displays the Asset tag or the Service tag for the system.

Option Description

Power Displays the power output of the system in BTU/hr or Watts. The display format can

be configured in the Set home submenu of the Setup menu.

Temperature Displays the temperature of the system in Celsius or Fahrenheit. The display format

can be configured in the Set home submenu of the Setup menu.

Back panel

Two-riser chassis

NOTE: This is only applicable for eight x 2.5-inch hard drive chassis.

Figure 6. Back panel features (two PCIe expansion cards)

1. System identification button 2. System identification connector

3. iDRAC8 Enterprise port 4. PCIe expansion card slot (riser 1)

5. Serial connector 6. Video connector

7. USB ports (2) 8. PCIe expansion card slot (riser 2)

9. Ethernet connectors (4) 10. Power supply unit (PSU1)

11. Power supply unit (PSU2)

Table 5. Back panel features (two PCIe expansion cards)

Item Indicator, Button, or

Connector Icon Description

1 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack. When one of these buttons is

pressed, the LCD panel on the front and the

system status indicator on the back flash until one

of the buttons is pressed again.

Press to toggle the system ID on and off. If the

system stops responding during POST, press and

hold the system ID button for more than five

seconds to enter BIOS progress mode.

Item Indicator, Button, or

Connector Icon Description

To reset iDRAC (if not disabled in F2 iDRAC setup),

press and hold for more than 15 seconds.

2 System identification

connector

Enables you to connect the optional system status

indicator assembly through the optional cable

management arm.

3 iDRAC8 Enterprise port Dedicated management port.

NOTE: The port is available for use only if the

iDRAC8 Enterprise license is installed on your

system.

4 PCIe expansion card slot

(riser 1)

Enables you to connect a low profile PCIe

expansion card. See the Expansion card installation

guidelines section.

5 Serial connector Enables you to connect a serial device to the

system.

6 Video connector Enables you to connect a VGA display to the

system.

7 USB ports (2) Enables you to connect USB devices to the system.

The ports are USB 3.0-compliant.

8 PCIe expansion card slot

(riser 2)

Enables you to connect a full height three-fourth

length PCIe expansion card. See the Expansion

card installation guidelines section.

9 Ethernet connectors (4) Four integrated 10/100/1000 Mbps NIC

connectors

Four integrated connectors:

• Two integrated 10/100/1000 Mbps NIC

connectors

• Two integrated 100 Mbps/1 Gbps/10 Gbps SFP

+ connectors

• Four 10 Gbps

10 PSU1 • Two 495 W, 750 W, or 1100 W AC power supply

units (PSUs)

• Two 1100 W DC PSUs

• Two 750 W mixed mode PSUs

11 PSU2 • Two 495 W, 750 W, or 1100 W AC PSUs

• Two 1100 W DC PSUs

Item Indicator, Button, or

Connector Icon Description

• Two 750 W mixed mode PSUs

Related Links

Expansion card installation guidelines

Three-riser chassis

NOTE: This is applicable for eight x 2.5-inch, 10 x 2.5-inch, or 24 x 1.8-inch hard drive chassis.

Figure 7. Back panel features (three PCIe expansion cards)

1. System identification button 2. System identification connector

3. pci 4. iDRAC8 Enterprise port

5. LP PCIe expansion card slot (riser 1) 6. Serial connector

7. LP PCIe expansion card slot (riser 2) 8. Video connector

9. USB port (2) 10. LP PCIe expansion card slot (riser 3)

11. Ethernet connectors (4) 12. Power supply (PSU1)

13. Power supply (PSU2)

Table 6. Back panel features (three PCIe expansion cards)

Item Indicator, Button, or

Connector Icon Description

1 System identification

button

The identification buttons on the front and back

panels can be used to locate a particular system

within a rack.

10/24 hard drive

system

When one of these buttons

is pressed, the system status

indicator on the back

flashes until one of the

buttons is pressed again.

Eight hard drive

system

When one of these buttons

is pressed, the LCD panel

on the front and the system

Item Indicator, Button, or

Connector Icon Description

status indicator on the back

flashes until one of the

buttons is pressed again.

Press to toggle the system ID on and off. If the

system stops responding during POST, press and

hold the system ID button for more than five

seconds to enter BIOS progress mode.

To reset iDRAC (if not disabled in F2 iDRAC setup)

press and hold for more than 15 seconds.

2 System identification

connector

Enables you to connect the optional system status

indicator assembly through the optional cable

management arm.

3 iDRAC8 Enterprise port Dedicated management port.

NOTE: The port is available for use only if the

iDRAC8 Enterprise license is installed on your

system.

4 LP PCIe expansion card

slot (riser 1)

Enables you to connect a low profile LP PCIe

expansion card. See the Expansion card installation

guidelines section.

5 Serial connector Enables you to connect a serial device to the

system.

6 LP PCIe expansion card

slot (riser 2)

Enables you to connect a low profile LP PCIe

expansion card. See the Expansion card installation

guidelines section.

7 Video connector Enables you to connect a VGA display to the

system.

8 USB port (2) Enables you to connect USB devices to the system.

The ports are USB 3.0-compliant.

9 LP PCIe expansion card

slot (riser 3)

Enables you to connect a LP PCIe expansion card.

See the Expansion card installation guidelines

section.

10 Ethernet connectors (4) Four integrated 10/100/1000 Mbps NIC

connectors

Four integrated connectors:

• Two integrated 10/100/1000 Mbps NIC

connectors

• Two integrated 100 Mbps/1 Gbps/10 Gbps SFP

+ connectors

Item Indicator, Button, or

Connector Icon Description

• Four 10 Gbps

11 PSU1 • Two 495 W, 750 W, or 1100 W AC power supply

units (PSUs)

• Two 1100 W DC PSUs

• Two 750 W mixed mode PSUs

12 PSU2 • Two 495 W, 750 W, or 1100 W AC PSUs

• Two 1100 W DC PSUs

• Two 750 W mixed mode PSUs

Related Links

Expansion card installation guidelines

Diagnostic indicators

The diagnostic indicators on the system front panel display system status during system startup.

NOTE: The diagnostic indicators are not present if the system is equipped with an LCD display.

NOTE: The diagnostic indicators are present only on the 10 hard drive and the 24 hard drive

systems.

NOTE: No diagnostic indicators are lit when the system is turned off. To start the system, plug it into

a working power source and press the power button.

Table 7. Diagnostic indicators

Icon Description Condition Corrective action

Health

indicator

The indicator turns solid

blue if the system is in good

health.

None required.

The indicator flashes amber:

• When the system is

turned on.

• When the system is in

standby.

• If any error condition

exists. For example, a

failed fan, PSU, or a hard

drive.

Check the System Event Log or system

messages for the specific issue. For more

information about error messages, see the

Dell Event and Error Messages Reference

Guide at Dell.com/openmanagemanuals >

OpenManage software.

The POST process is interrupted without

any video output due to invalid memory

configurations. See the Getting help

section.

Icon Description Condition Corrective action

Hard drive

indicator

The indicator flashes amber

if there is a hard drive error.

Check the System Event Log to determine

the hard drive that has an error. Run the

appropriate Online Diagnostics test. Restart

the system and run embedded diagnostics

(ePSA). If the hard drives are configured in a

RAID array, restart the system and enter the

host adapter configuration utility program.

Electrical

indicator

The indicator flashes amber

if the system experiences an

electrical error (for example,

voltage out of range, or a

failed power supply unit

(PSU) or voltage regulator).

Check the System Event Log or system

messages for the specific issue. If it is due

to a problem with the PSU, check the LED

on the PSU. Reseat the PSU. If the problem

persists, see the Getting help section.

Temperature

indicator

The indicator flashes amber

if the system experiences a

thermal error (for example,

the ambient temperature is

out of range or fan failure).

Ensure that none of the following

conditions exist:

• A cooling fan has been removed or has

failed.

• System cover, cooling shroud, EMI filler

panel, memory module blank, or back

filler bracket is removed.

• Ambient temperature is too high.

• External airflow is obstructed.

See the Getting help section.

Memory

indicator

The indicator flashes amber

if a memory error occurs.

Check the system event log or system

messages for the location of the failed

memory. Reseat the memory module. If

the problem persists, see the Getting help

section.

PCIe indicator The indicator flashes amber

if a PCIe card experiences

an error.

Restart the system. Update any required

drivers for the PCIe card. Reinstall the card.

If the problem persists, see the Getting help

section.

NOTE: For more information on

supported PCIe cards, see the

Expansion card installation guidelines

section.

Related Links

Getting help

Expansion card installation guidelines

Hard drive indicator codes

Figure 8. Hard drive indicators

1. hard drive activity indicator 2. hard drive status indicator

3. hard drive

NOTE: If the hard drive is in the Advanced Host Controller Interface (AHCI) mode, the status

indicator (on the right side) does not function and remains off.

Table 8. Hard drive indicator codes

Drive-status indicator pattern (RAID only) Condition

Flashes green twice per second Identifying drive or preparing for removal.

Off Drive ready for insertion or removal.

NOTE: The drive status indicator remains off until

all hard drives are initialized after the system is

turned on. Drives are not ready for insertion or

removal during this time.

Flashes green, amber, and turns off Predicted drive failure

Flashes amber four times per second Drive failed

Flashes green slowly Drive rebuilding

Steady green Drive online

Flashes green for three seconds, amber for

three seconds, and turns off after six seconds Rebuild stopped

uSATA SSD indicator codes

Figure 9. uSATA SSD indicators

1. uSATA SSD activity indicator 2. uSATA SSD status indicator

3. uSATA SSD

NOTE: If the SSD is in the Advanced Host Controller Interface (AHCI) mode, the status indicator (on

the right side) does not function and remains off.

Table 9. Drive status indicator codes

Drive-status indicator pattern Condition

Flashes green twice per second Identifying drive or preparing for removal.

Off Drive ready for insertion or removal.

NOTE: The drive status indicator remains off until

all hard drives are initialized after the system is

turned on. Drives are not ready for insertion or

removal during this time.

Flashes green, amber, and turns off Predicted drive failure

Flashes amber four times per second Drive failed

Steady green Drive online

Flashes green for three seconds, amber for

three seconds, and turns off after six seconds

Rebuild aborted

NIC indicator codes

Figure 10. NIC indicators

1. link indicator 2. activity indicator

Table 10. NIC indicators

Convention Status Condition

A Link and activity indicators are off The NIC is not connected to the

network.

B Link indicator is green The NIC is connected to a valid network

at its maximum port speed (1 Gbps or 10

Gbps).

C Link indicator is amber The NIC is connected to a valid network

at less than its maximum port speed.

D Activity indicator is flashing green Network data is being sent or received.

Power supply unit indicator codes

AC power supply units (PSUs) have an illuminated translucent handle that serves as an indicator and DC

PSUs have an LED that serves as an indicator. The indicator shows whether power is present or a power

fault has occurred.

Figure 11. AC PSU status indicator

1. AC PSU status indicator/handle

Table 11. AC PSU status indicators

Convention Power indicator

pattern Condition

A Green A valid power source is connected to the PSU and the PSU is

operational.

B Flashing green When the firmware of the PSU is being updated, the PSU handle

flashes green.

C Flashing green

and turns off

When hot-adding a PSU, the PSU handle flashes green five times at

4 Hz rate and turns off. This indicates a PSU mismatch with respect

to efficiency, feature set, health status, and supported voltage.

NOTE: Ensure that both the PSUs are of the same capacity.

CAUTION: For AC PSUs, use only PSUs with the Extended

Power Performance (EPP) label on the back.

NOTE: Mixing PSUs from previous generations of Dell

PowerEdge servers can result in a PSU mismatch condition or

failure to turn the system on.

D Flashing amber Indicates a problem with the PSU.

Convention Power indicator

pattern Condition

CAUTION: When correcting a PSU mismatch, replace only the

PSU with the flashing indicator. Swapping the PSU to make a

matched pair can result in an error condition and unexpected

system shutdown. To change from a high output

configuration to a low output configuration or vice versa, you

must power down the system.

CAUTION: AC PSUs support both 220 V and 110 V input

voltages with the exception of Titanium PSUs, which support

only 220 V. When two identical PSUs receive different input

voltages, they can output different wattages, and trigger a

mismatch.

CAUTION: If two PSUs are used, they must be of the same type

and have the same maximum output power.

CAUTION: Combining AC and DC PSUs is not supported and

triggers a mismatch.

E Not lit Power is not connected.

Figure 12. DC PSU status indicator

1. DC PSU status indicator

Table 12. DC PSU status indicators

Convention Power indicator

pattern Condition

A Green A valid power source is connected to the PSU and that the PSU is

operational.

B Flashing green When hot-adding a PSU, the PSU indicator flashes green. This

indicates that there is a PSU mismatch with respect to efficiency,

feature set, health status, and supported voltage. Ensure that both

the PSUs are of the same capacity.

C Flashing amber Indicates a problem with the PSU.

CAUTION: When correcting a PSU mismatch, replace only

the PSU with the flashing indicator. Swapping the PSU to

make a matched pair can result in an error condition and

unexpected system shutdown. To change from a High

Output configuration to a Low Output configuration or vice

versa, you must power down the system.

CAUTION: AC PSU support both 220 V and 110 V input

voltages with the exception of Titanium PSU, which support

only 220 V. When two identical PSU receive different input

voltages, they can output different wattages, and trigger a

mismatch.

CAUTION: If two PSU are used, they must be of the same

type and have the same maximum output power.

CAUTION: Combining AC and DC PSU is not supported and

triggers a mismatch.

D Not lit Power is not connected.

iDRAC Direct LED indicator codes

NOTE: The iDRAC Direct LED indicator does not turn on when the USB port is used in the USB

mode.

Figure 13. iDRAC Direct LED indicator

1. iDRAC Direct status indicator

The iDRAC Direct LED indicator table describes iDRAC Direct activity when configuring iDRAC Direct by

using the management port (USB XML Import).

Table 13. iDRAC Direct LED indicators

Convention iDRAC Direct

LED indicator

pattern

Condition

A Green Turns green for a minimum of two seconds to indicate the start and

end of a file transfer.

B Flashing green Indicates file transfer or any operation tasks.

C Green and turns

off

Indicates that the file transfer is complete.

D Not lit Indicates that the USB is ready to be removed or that a task is

complete.

The following table describes iDRAC Direct activity when configuring iDRAC Direct by using your laptop

and cable (Laptop Connect):

Table 14. iDRAC Direct LED indicator patterns

iDRAC Direct LED

indicator pattern Condition

Solid green for two

seconds

Indicates that the laptop is connected.

Flashing green (on

for two seconds and

off for two seconds)

Indicates that the laptop connected is recognized.

Turns off Indicates that the laptop is unplugged.

Quick Sync indicator codes

Figure 14. Quick Sync indicator codes

1. Quick Sync status indicator 2. Quick Sync activation button

Table 15. Quick Sync indicator codes

Power indicator pattern Condition

Slow flash Indicates that Quick Sync is waiting to be configured

from iDRAC.

Solid Indicates that Quick Sync is ready to transfer.

Flashes three times rapidly and then turns off Indicates that the Quick Sync feature is disabled from

iDRAC.

Flashes continuously when the mobile device

touches the antenna

Indicates data transfer activity.

Flashes rapidly five times and turns off for one

second when the activation button is pressed.

This pattern is repeated until the activation

button is pressed again.

Indicates that the Quick Sync hardware is not

responding properly. Reseat the bezel. If the problem

persists, see Getting help section.

Off Indicates that the Quick Sync feature is turned off.

Use the activation button to enable it. If pressing the

activation button does not turn on the LEDs, it

indicates that power is not delivered to the Quick

Sync bezel.

NOTE: For security purposes, Quick Sync turns

off after 30 seconds of inactivity after the

activation button is pressed. After timed-out, the

user is expected to press the activation button

again to activate Quick Sync.

Related Links

Getting help

Locating Service Tag of your system

Your system is identified by a unique Express Service Code and Service Tag number. The Express Service

Code and Service Tag are found on the front of the system by pulling out the information tag.

Alternatively, the information may be on a sticker on the chassis of the system. This information is used

by Dell to route support calls to the appropriate personnel.

Documentation resources

This section provides information about the documentation resources for your system.

Table 16. Documentation resources for system

Task Document Location

Setting up your system For information about installing the

system into a rack, see the Rack

documentation included with your

rack solution.

Dell.com/poweredgemanuals

For information about turning on the

system and the technical

specifications of your system, see the

Getting Started With Your System that

shipped with your system.

Dell.com/poweredgemanuals

For information about Getting Started

With Your System that shipped with

your system or the Technical

specifications section in this

document.

Dell.com/poweredgemanuals

Configuring your

system

For information about iDRAC features,

configuring and logging in to iDRAC,

and managing your system remotely,

see the Integrated Dell Remote Access

Controller User's Guide.

Dell.com/idracmanuals

For information about installing the

operating system, see the operating

system documentation.

Dell.com/operatingsystemmanuals

For information about understanding

Remote Access Controller Admin

(RACADM) subcommands and

supported RACADM interfaces, see the

RACADM Command Line Reference

Guide for iDRAC.

Dell.com/idracmanuals

For information about updating drivers

and firmware, see the Download

firmware and drivers section in this

document.

Dell.com/support/drivers

Managing your system For information about the features of

the Dell OpenManage Systems

Dell.com/openmanagemanuals

Task Document Location

Management, see the Dell

OpenManage Systems Management

Overview Guide.

For information about setting up,

using, and troubleshooting

OpenManage, see the Dell

OpenManage Server Administrator

User’s Guide.

Dell.com/openmanagemanuals

For information about installing, using,

and troubleshooting Dell

OpenManage Essentials, see the Dell

OpenManage Essentials User’s Guide.

Dell.com/openmanagemanuals

For information about installing and

using Dell System E-Support Tool

(DSET), see the Dell System E-Support

Tool (DSET) User's Guide.

Dell.com/DSET

For information about installing and

using Active System Manager (ASM),

see the Active System Manager User’s

Guide.

Dell.com/asmdocs

For understanding the features of Dell

Lifecycle Controller (LCC), see the Dell

Lifecycle Controller User’s Guide.

Dell.com/idracmanuals

For information about partner

programs enterprise systems

management, see the OpenManage

Connections Enterprise Systems

Management documents.

Dell.com/

omconnectionsenterprisesystemsman

agement

For information about connections

and client systems management, see

the OpenManage Connections Client

Systems Management documentation.

Dell.com/

dellclientcommandsuitemanuals

For information about viewing

inventory, performing configuration

and monitoring tasks, remotely

turning on or off servers, and enabling

alerts for events on servers and

components using the Dell Chassis

Management Controller (CMC), see

the CMC User’s Guide.

Dell.com/esmmanuals

Working with Dell

PowerEdge RAID

controllers

For information about understanding

the features of the Dell PowerEdge

RAID controllers (PERC) and deploying

Dell.com/storagecontrollermanuals

Task Document Location

the PERC cards, see the Storage

controller documentation.

Understanding event

and error messages

For information about checking the

event and error messages generated

by the system firmware and agents

that monitor system components, see

the Dell Event and Error Messages

Reference Guide.

Dell.com/openmanagemanuals >

OpenManage software

Technical specifications

The technical and environmental specifications of your system are outlined in this section.

Chassis dimensions

Figure 15. Chassis dimensions of PowerEdge R630 system

Table 17. Dimensions of the Dell PowerEdge R630 system

System Xa Xb Y Za (with

bezel) Za

(without

bezel)

Zb Zc

Eight x 2.5-inch

hard drive systems

482.4 mm 434.0 mm 42.8 mm 35.0 mm 20.4 mm 682.7 mm 701.3 mm

10 x 2.5-inch and

24 x 2.5-inch hard

drive systems

482.4 mm 434.0 mm 42.8 mm 35.0 mm 20.4 mm 731.0 mm 752.1 mm

Chassis weight

Table 18. Chassis weight

System Maximum weight

Eight x 2.5-inch hard drive systems 16.9 kg (37. 26 lb)

10 x 2.5-inch hard drive systems 18.5 kg (40. 79 lb)

24 x 1.8-inch hard drive systems 17.4 kg (38. 36 lb)

Processor specifications

The PowerEdge R630 system supports up to two Intel Xeon E5-2600 v3 or v4 product family processors.

PSU specifications

The PowerEdge R630 system supports up to two AC or DC redundant power supply units (PSUs).

Table 19. PSU specifications

PSU Class Heat dissipation

(maximum) Frequency Voltage

495 W AC Platinum 1908 BTU/hr 50/60 Hz 100–240 V AC,

autoranging

750 W AC Platinum 2891 BTU/hr 50/60 Hz 100–240 V AC,

autoranging

750 W AC Titanium 2843 BTU/hr 50/60 Hz 200–240 V AC,

autoranging

1100 W AC Platinum 4100 BTU/hr 50/60 Hz 100–240 V AC,

autoranging

1100 W DC — 4416 BTU/hr — –(48–60) V DC

750 W DC (for

China only)

Platinum 2902 BTU/hr 50/60 Hz 100–240 V AC and

240 V DC

NOTE: Heat dissipation is calculated by using the PSU wattage rating.

NOTE: This system is also designed to connect to the IT power systems with a phase to phase

voltage not exceeding 230 V.

System battery specifications

The PowerEdge R630 system supports CR 2032 3.0-V lithium coin cell system battery.

Expansion bus specifications

The PowerEdge R630 system supports PCI express (PCIe) generation 3 expansion cards, which must be

installed on the system board by using expansion card risers. This system supports three types of

expansion card risers. The following table provides detailed information about the expansion card riser

specifications:

Table 20. Expansion card riser specifications

Expansion card

riser PCIe slots on the

riser Height Length Link

Riser 1 Slot 1 Low Profile Half Length x16

Slot 2 Low Profile Half Length x8

Riser 2 Slot 1 Low Profile Half Length x8

Slot 1 Low Profile Half Length x16

Riser 3 Slot 2 Full height Three-fourth Length x16

Slot 3 Low Profile Half Length x16

NOTE: When using slot 1 on the riser, ensure that both the processors are installed on the system.

NOTE: Only a three-fourth length card is supported for the PCIe expansion card slot (slot 2) on riser

3 when no mini-PERC card is installed. Supported length with mini-PERC card installed is half

length.

Memory specifications

The PowerEdge R630 system supports DDR4 registered DIMMs (RDIMMs) and load-reduced DIMMs

(LRDIMMs) at 1866 MT/s, 2133 MT/s, or 2400 MT/s.

Table 21. Memory specifications

Memory module

sockets Memory capacity Minimum RAM Maximum RAM

Twenty-four 288-pins • 64 GB quad rank

(LRDIMMs)

• 4 GB or 8 GB single

rank (RDIMMs)

• 8 GB, 16 GB or 32 GB

dual rank (RDIMMs)

• 4 GB with single

processor

• 8 GB with dual

processors

(minimum one

memory module per

processor)

• LRDIMM: up to 786

GB with single

processor

• LRDIMM: up to 1536

GB with dual

processors

• RDIMM: up to 384

GB with single

processor

Memory module

sockets Memory capacity Minimum RAM Maximum RAM

• RDIMM: up to 786

GB with dual

processors

Drive specifications

Hard drives

The PowerEdge R630 system supports:

• Up to eight 2.5-inch, internal, hot swappable SAS, SATA, or Nearline SAS hard drives

• Up to ten 2.5-inch, internal, hot swappable SAS, SATA, or Nearline SAS hard drives

• Up to twenty four 1.8-inch, internal, hot swappable SAS, SATA, or Nearline SAS hard drives

Optical drive

The PowerEdge R630 system supports one optional SATA DVD-ROM drive or DVD+/-RW drive on 8 hard

drive systems only.

Ports and connectors specifications

USB ports

The PowerEdge R630 system supports:

• USB 2.0-compliant ports on the front panel

• USB 3.0-complaint ports on the back panel

• Internal USB 3.0-compliant port

Table 22. USB specifications

System Front panel Back panel Internal

PowerEdge R630 For eight hard drive

systems:

• Two 4-pin, USB 2.0-

compliant ports

• vFlash memory card

slot

For 24 or 10 hard drive

systems:

• One micro USB 2.0-

compliant port

Two 9-pin, USB 3.0-

compliant ports

One 9-pin, USB 3.0-

compliant

NIC ports

The PowerEdge R630 system supports four Network Interface Controller (NIC) ports on the back panel,

which is available in one of the following three NIC configurations:

• Four 10/100/1000 Mbps

• Two 10/100/1000 Mbps and two 100 Mbps/1 Gbps/10 Gbps

• Four 10 Gbps

Serial connector

The serial connector connects a serial device to the system. The PowerEdge R630 system supports one

serial connector on the back panel, which is a 9-pin connector, Data Terminal Equipment (DTE), 16550-

compliant.

VGA ports

The Video Graphic Array (VGA) port enables you to connect the system to a VGA display. The PowerEdge

R630 system supports two 15-pin VGA ports on the front and back panels.

Internal Dual SD Module

The PowerEdge R630 system supports two optional flash memory card slots with an internal dual SD

module.

NOTE: One card slot is dedicated for redundancy.

Video specifications

The PowerEdge R630 system supports Integrated VGA controller with 16 MB capacity.

Table 23. Resolution information for video modes

Resolution Refresh rate (Hz) Color depth (bit)

640 X 480 60, 70 8, 16, 32

800 X 600 60, 75, 85 8, 16, 32

1024 X 768 60, 75, 85 8, 16, 32

1152 X 864 60, 75, 85 8, 16, 32

1280 X 1024 60, 75 8, 16, 32

1440 X 900 60 8, 16, 32

Environmental specifications

NOTE: For additional information about environmental measurements for specific system

configurations, see Dell.com/environmental_datasheets.

Table 24. Temperature specifications

Temperature Specifications

Storage –40°C to 65°C (–40°F to 149°F)

Continuous operation (for altitude less than 950 m

or 3117 ft)

10°C to 35°C (50°F to 95°F) with no direct sunlight

on the equipment.

NOTE: Maximum of 145 W 22 core processor

is supported in systems with eight 2.5-inches

drives, two PCI slot chassis, and 75 W single

wide active GPU.

Fresh air For information about fresh air, see Expanded

Operating Temperature section.

Maximum temperature gradient (operating and

storage)

20°C/h (36°F/h)

Table 25. Relative humidity specifications

Relative humidity Specifications

Storage 5% to 95% RH with 33°C (91°F) maximum dew

point. Atmosphere must be non-condensing at all

times.

Operating 10% to 80% relative humidity with 29°C (84.2°F)

maximum dew point.

Table 26. Maximum vibration specifications

Maximum vibration Specifications

Operating 0.26 Grms at 5 Hz to 350 Hz (all operation

orientations).

Storage 1.88 Grms at 10 Hz to 500 Hz for 15 min (all six

sides tested).

Table 27. Maximum shock specifications

Maximum shock Specifications

Operating Six consecutively executed shock pulses in the

positive and negative x, y, and z axes of 40 G for up

to 2.3 ms.

Storage Six consecutively executed shock pulses in the

positive and negative x, y, and z axes (one pulse on

each side of the system) of 71 G for up to 2 ms.

Table 28. Maximum altitude specifications

Maximum altitude Specifications

Operating 3048 m (10,000 ft)

Storage 12,000 m (39,370 ft)

Table 29. Operating temperature de-rating specifications

Operating temperature de-rating Specifications

Up to 35°C (95°F) Maximum temperature is reduced by 1°C/300 m

(1°F/547 ft) above 950 m (3,117 ft).

35°C to 40°C (95°F to 104°F) Maximum temperature is reduced by 1°C/175 m

(1°F/319 ft) above 950 m (3,117 ft).

40°C to 45°C (104°F to 113°F) Maximum temperature is reduced by 1°C/125 m

(1°F/228 ft) above 950 m (3,117 ft).

Related Links

Expanded operating temperature

Particulate and gaseous contamination specifications

The following table defines the limitations that help avoid any equipment damage or failure from

particulates and gaseous contamination. If the levels of particulates or gaseous pollution exceed the

specified limitations and result in equipment damage or failure, you may need to rectify the

environmental conditions. Re-mediation of environmental conditions is the responsibility of the

customer.

Table 30. Particulate contamination specifications

Particulate contamination Specifications

Air filtration Data center air filtration as defined by ISO Class 8

per ISO 14644-1 with a 95% upper confidence

limit.

NOTE: This condition applies only to data

center environments. Air filtration

requirements do not apply to IT equipment

designed to be used outside a data center, in

environments such as an office or factory

floor.

NOTE: Air entering the data center must have

MERV11 or MERV13 filtration.

Conductive dust Air must be free of conductive dust, zinc whiskers,

or other conductive particles.

NOTE: This condition applies to data center

and non-data center environments.

Corrosive dust • Air must be free of corrosive dust.

Particulate contamination Specifications

• Residual dust present in the air must have a

deliquescent point less than 60% relative

humidity.

NOTE: This condition applies to data center

and non-data center environments.

Table 31. Gaseous contamination specifications

Gaseous contamination Specifications

Copper coupon corrosion rate <300 Å/month per Class G1 as defined by ANSI/

ISA71.04-1985.

Silver coupon corrosion rate <200 Å/month as defined by AHSRAE TC9.9.

NOTE: Maximum corrosive contaminant levels measured at ≤50% relative humidity.

Standard operating temperature

Table 32. Standard operating temperature specifications

Standard operating temperature Specifications

Temperature ranges (for altitude less than 950

metres or 3117 feet)

10°C to 35°C (50°F to 95°F) with no direct sunlight

on the equipment.

NOTE: Maximum of 145 W 22–core processor

is supported in systems with eight 2.5-inch

drives 2–PCI slot chassis, and 75 W single

wide active GPU.

Standard operating temperature restrictions • Ambient temperature is restricted to 30°C for

systems with eight 2.5-inches drives or ten 2.5-

inch drives chassis, with no PCIe SSD and a

maximum of 160 W workstation processor.

• Ambient temperature is restricted to 30°C for

systems with ten 2.5-inch drives chassis, PCIe

SSD and a maximum of 135 W processor.

• Ambient temperature is restricted to 35°C for

systems with ten 2.5-inch drives chassis, PCIe

SSD and a maximum of 120 W processor.

• Ambient temperature is restricted to 35°C for

systems with twenty-four 1.8-inch drives

chassis, PCIe SSD, and a maximum of 135 W

processor.

Expanded operating temperature

Table 33. Expanded operating temperature specifications

Expanded operating temperature Specifications

Continuous operation 5°C to 40°C at 5% to 85% RH with 29°C dew point.

Expanded operating temperature Specifications

NOTE: Outside the standard operating

temperature (10°C to 35°C), the system can

operate continuously in temperatures as low

as 5°C and as high as 40°C.

For temperatures between 35°C and 40°C, de-rate

maximum allowable temperature by 1°C per 175 m

above 950 m (1°F per 319 ft).

≤ 1% of annual operating hours –5°C to 45°C at 5% to 90% RH with 29°C dew

point.

NOTE: Outside the standard operating

temperature (10°C to 35°C), the system can

operate down to –5°C or up to 45°C for a

maximum of 1% of its annual operating hours.

For temperatures between 40°C and 45°C, de-rate

maximum allowable temperature by 1°C per 125 m

above 950 m (1°F per 228 ft).

NOTE: When operating in the expanded temperature range, system performance may be impacted.

NOTE: When operating in the expanded temperature range, ambient temperature warnings may be

reported on the LCD panel and in the System Event Log.

Expanded operating temperature restrictions

• Do not perform a cold startup below 5°C.

• The operating temperature specified is for a maximum altitude of 3050 m (10,000 ft).

• 145 W and Workstation CPU (160 W) processors are not supported.

• Two power supply units (PSUs) are needed and one PSU failure is not supported.

• Non-Dell qualified peripheral cards and/or peripheral cards greater than 25 W are not supported.

• PCIe SSD and 1.8-inch SSDs are not supported.

• GPU is not supported.

Initial system setup and configuration

Setting up your system

Complete the following steps to set up your system:

1. Unpack the system.

2. Install the system into the rack. For more information about installing the system into the rack, see

your system Rack Installation Placemat at Dell.com/poweredgemanuals.

3. Connect the peripherals to the system.

4. Connect the system to its electrical outlet.

5. Turn the system on by pressing the power button or by using iDRAC.

6. Turn on the attached peripherals.

iDRAC configuration

The Integrated Dell Remote Access Controller (iDRAC) is designed to make system administrators more

productive and improve the overall availability of Dell systems. iDRAC alerts administrators to system

issues, helps them perform remote system management, and reduces the need for physical access to the

system.

Options to set up iDRAC IP address

You must configure the initial network settings based on your network infrastructure to enable the

communication to and from iDRAC. You can set up the IP address by using one of the following

interfaces:

Interfaces Document/Section

iDRAC Settings

utility

See Dell Integrated Dell Remote Access Controller User's Guide at Dell.com/

idracmanuals

Dell Deployment

Toolkit

See Dell Deployment Toolkit User’s Guide at Dell.com/openmanagemanuals

Dell Lifecycle

Controller

See Dell Lifecycle Controller User’s Guide at Dell.com/idracmanuals

Chassis or Server

LCD panel

See the LCD panel section

You must use the default iDRAC IP address 192.168.0.120 to configure the initial network settings,

including setting up DHCP or a static IP for iDRAC.

NOTE: To access iDRAC, ensure that you install the iDRAC port card or connect the network cable

to the Ethernet connector 1 on the system board.

NOTE: Ensure that you change the default user name and password after setting up the iDRAC IP

address.

Related Links

LCD panel

You can log in to iDRAC as:

• iDRAC user

• Microsoft Active Directory user

• Lightweight Directory Access Protocol (LDAP) user

The default user name and password are root and calvin. You can also log in by using Single Sign-On

or Smart Card.

NOTE: You must have iDRAC credentials to log in to iDRAC.

For more information about logging in to iDRAC and iDRAC licenses, see the Integrated Dell Remote

Access Controller User's Guide at Dell.com/idracmanuals.

Options to install the operating system

If the system is shipped without an operating system, install the supported operating system by using one

of the following resources:

Table 34. Resources to install the operating system

Resources Location

Dell Systems Management Tools and

Documentation media

Dell.com/operatingsystemmanuals

Dell Lifecycle Controller Dell.com/idracmanuals

Dell OpenManage Deployment Toolkit Dell.com/openmanagemanuals

Dell certified VMware ESXi Dell.com/virtualizationsolutions

Supported operating systems on Dell PowerEdge

systems

Dell.com/ossupport

Installation and How-to videos for supported

operating systems on Dell PowerEdge systems

Supported Operating Systems for Dell PowerEdge

Systems

Methods to download firmware and drivers

You can download the firmware and drivers by using the following methods:

Table 35. Firmware and drivers

Methods Location

From the Dell Support site Dell.com/support/home

Using Dell Remote Access Controller Lifecycle

Controller (iDRAC with LC)

Dell.com/idracmanuals

Methods Location

Using Dell Repository Manager (DRM) Dell.com/openmanagemanuals

Using Dell OpenManage Essentials (OME) Dell.com/openmanagemanuals

Using Dell Server Update Utility (SUU) Dell.com/openmanagemanuals

Using Dell OpenManage Deployment Toolkit (DTK) Dell.com/openmanagemanuals

Downloading the drivers and firmware

Dell recommends that you download and install the latest BIOS, drivers, and systems management

firmware on your system.

Prerequisites

Ensure that you clear the web browser cache before downloading the drivers and firmware.

Steps

1. Go to Dell.com/support/drivers.

2. Under the Drivers & Downloads section, type the Service Tag of your system in the Service Tag or

Express Service Code box.

NOTE: If you do not have the Service Tag, select Detect My Product to allow the system to

automatically detect your Service Tag, or under General support, navigate to your product.

3. Click Drivers & Downloads.

The drivers that are applicable to your selection are displayed.

4. Download the drivers you need to a USB drive, CD, or DVD.

Pre-operating system management

applications

You can manage basic settings and features of a system without booting to the operating system by

using the system firmware.

Options to manage the pre-operating system

applications

Your system has the following options to manage the pre-operating system applications:

• System Setup

• Boot Manager

• Dell Lifecycle Controller

• Preboot Execution Environment (PXE)

Related Links

System Setup

Boot Manager

Dell Lifecycle Controller

PXE boot

System Setup

By using the System Setup screen, you can configure the BIOS settings, iDRAC settings, and device

settings of your system.

NOTE: Help text for the selected field is displayed in the graphical browser by default. To view the

help text in the text browser, press F1.

You can access system setup by using two methods:

• Standard graphical browser—The browser is enabled by default.

• Text browser—The browser is enabled by using Console Redirection.

Related Links

System Setup details

Viewing System Setup

To view the System Setup screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

Related Links

System Setup

System Setup details

The System Setup Main Menu screen details are explained as follows:

Option Description

System BIOS Enables you to configure BIOS settings.

iDRAC Settings Enables you to configure iDRAC settings.

The iDRAC settings utility is an interface to set up and configure the iDRAC

parameters by using UEFI (Unified Extensible Firmware Interface). You can enable

or disable various iDRAC parameters by using the iDRAC settings utility. For more

information about this utility, see Integrated Dell Remote Access Controller User’s

Guide at Dell.com/idracmanuals.

Device Settings Enables you to configure device settings.

Related Links

System Setup

iDRAC Settings utility

Device Settings

Viewing System Setup

System BIOS

You can use the System BIOS screen to edit specific functions such as boot order, system password,

setup password, set the RAID mode, and enable or disable USB ports.

Related Links

System BIOS Settings details

Boot Settings

Network Settings

System Information

Memory Settings

Processor Settings

SATA Settings

Integrated Devices

Serial Communication

System Profile Settings

Miscellaneous Settings

iDRAC Settings utility

Device Settings

System Security

Viewing System BIOS

To view the System BIOS screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

Related Links

System BIOS

System BIOS Settings details

The System BIOS Settings screen details are explained as follows:

Option Description

System

Information

Specifies information about the system such as the system model name, BIOS

version, and Service Tag.

Memory Settings Specifies information and options related to the installed memory.

Processor Settings Specifies information and options related to the processor such as speed and

cache size.

SATA Settings Specifies options to enable or disable the integrated SATA controller and ports.

Boot Settings Specifies options to specify the boot mode (BIOS or UEFI). Enables you to modify

UEFI and BIOS boot settings.

Network Settings Specifies options to change the network settings.

Integrated

Devices

Specifies options to manage integrated device controllers and ports and specify

related features and options.

Serial

Communication

Specifies options to manage the serial ports and specify related features and

options.

System Profile

Settings

Specifies options to change the processor power management settings, memory

frequency, and so on.

System Security Specifies options to configure the system security settings, such as system

password, setup password, Trusted Platform Module (TPM) security. It also

manages the power and NMI buttons on the system.

Miscellaneous

Settings

Specifies options to change the system date, time, and so on.

Related Links

System BIOS

Viewing System BIOS

Boot Settings

You can use the Boot Settings screen to set the boot mode to either BIOS or UEFI. It also enables you to

specify the boot order.

Related Links

Boot Settings details

System BIOS

Viewing Boot Settings

Choosing the system boot mode

Changing the boot order

Viewing Boot Settings

To view the Boot Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Boot Settings.

Related Links

Boot Settings

Boot Settings details

Choosing the system boot mode

Changing the boot order

Boot Settings details

The Boot Settings screen details are explained as follows:

Option Description

Boot Mode Enables you to set the boot mode of the system.

CAUTION: Switching the boot mode may prevent the system from booting if

the operating system is not installed in the same boot mode.

If the operating system supports UEFI, you can set this option to UEFI. Setting this

field to BIOS allows compatibility with non-UEFI operating systems. This option is

set to BIOS by default.

NOTE: Setting this field to UEFI disables the BIOS Boot Settings menu. Setting

this field to BIOS disables the UEFI Boot Settings menu.

Boot Sequence

Retry

Enables or disables the Boot Sequence Retry feature. If this option is set to Enabled

and the system fails to boot, the system reattempts the boot sequence after 30

seconds. This option is set to Enabled by default.

Option Description

Hard-Disk Failover Specifies the hard drive that is booted in the event of a hard drive failure. The

devices are selected in the Hard-Disk Drive Sequence on the Boot Option Setting

menu. When this option is set to Disabled, only the first hard drive in the list is

attempted to boot. When this option is set to Enabled, all hard drives are attempted

to boot in the order selected in the Hard-Disk Drive Sequence. This option is not

enabled for UEFI Boot Mode.

Boot Option

Settings

Configures the boot sequence and the boot devices.

Related Links

Boot Settings

Viewing Boot Settings

Choosing the system boot mode

Changing the boot order

Choosing the system boot mode

System Setup enables you to specify one of the following boot modes for installing your operating

system:

• BIOS boot mode (the default) is the standard BIOS-level boot interface.

• Unified Extensible Firmware Interface (UEFI) boot mode is an enhanced 64-bit boot interface. If you

have configured your system to boot to UEFI mode, it replaces the system BIOS.

1. From the System Setup Main Menu, click Boot Settings, and select Boot Mode.

2. Select the boot mode you want the system to boot into.

CAUTION: Switching the boot mode may prevent the system from booting if the operating

system is not installed in the same boot mode.

3. After the system boots in the specified boot mode, proceed to install your operating system from

that mode.

NOTE: Operating systems must be UEFI-compatible to be installed from the UEFI boot mode. DOS

and 32-bit operating systems do not support UEFI and can only be installed from the BIOS boot

mode.

NOTE: For the latest information about supported operating systems, go to Dell.com/ossupport.

Related Links

Boot Settings

Boot Settings details

Viewing Boot Settings

Changing the boot order

You may have to change the boot order if you want to boot from a USB key or an optical drive. The

following instructions may vary if you have selected BIOS for Boot Mode.

1. On the System Setup Main Menu screen, click System BIOS → Boot Settings.

2. Click Boot Option Settings → Boot Sequence.

3. Use the arrow keys to select a boot device, and use the plus (+) and minus (-) sign keys to move the

device down or up in the order.

4. Click Exit, and then click Yes to save the settings on exit.

Related Links

Boot Settings

Boot Settings details

Viewing Boot Settings

Network Settings

You can use the Network Settings screen to modify PXE device settings. The network settings option is

available only in the UEFI mode.

NOTE: The BIOS does not control network settings in the BIOS mode. For the BIOS boot mode, the

optional Boot ROM of the network controllers handles the network settings.

Related Links

UEFI iSCSI Settings

Network Settings screen details

UEFI iSCSI Settings details

System BIOS

Viewing Network Settings

Viewing UEFI iSCSI Settings

Viewing Network Settings

To view the Network Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Network Settings.

Related Links

Network Settings

Network Settings screen details

The Network Settings screen details are explained as follows:

Option Description

PXE Device n (n =

1 to 4)

Enables or disables the device. When enabled, a UEFI boot option is created for the

device.

PXE Device n

Settings (n = 1 to

Enables you to control the configuration of the PXE device.

Related Links

Network Settings

Viewing Network Settings

UEFI iSCSI Settings

You can use the iSCSI Settings screen to modify iSCSI device settings. The iSCSI Settings option is

available only in the UEFI boot mode. BIOS does not control network settings in the BIOS boot mode. For

the BIOS boot mode, the option ROM of the network controller handles the network settings.

Related Links

UEFI iSCSI Settings details

Viewing UEFI iSCSI Settings

To view the UEFI iSCSI Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Network Settings.

5. On the Network Settings screen, click UEFI iSCSI Settings.

Related Links

UEFI iSCSI Settings

UEFI iSCSI Settings details

The UEFI ISCSI Settings screen details are explained as follows:

Option Description

ISCSI Initiator

Name

Specifies the name of the iSCSI initiator (iqn format).

ISCSI Device n (n =

1 to 4)

Enables or disables the iSCSI device. When disabled, a UEFI boot option is created

for the iSCSI device automatically.

System Security

You can use the System Security screen to perform specific functions such as setting the system

password, setup password and disabling the power button.

Related Links

System Security Settings details

Operating with a setup password enabled

System BIOS

Viewing System Security

Creating a system and setup password

Using your system password to secure your system

Deleting or changing system and setup password

Viewing System Security

To view the System Security screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Security.

Related Links

System Security

System Security Settings details

The System Security Settings screen details are explained as follows:

Option Description

Intel AES-NI Improves the speed of applications by performing encryption and decryption by

using the Advanced Encryption Standard Instruction Set (AES-NI). This option is set

to Enabled by default.

System Password Sets the system password. This option is set to Enabled by default and is read-only

if the password jumper is not installed in the system.

Setup Password Sets the setup password. This option is read-only if the password jumper is not

installed in the system.

Password Status Locks the system password. This option is set to Unlocked by default.

TPM Security NOTE: The TPM menu is available only when the TPM module is installed.

Enables you to control the reporting mode of the TPM. The TPM Security option is

set to Off by default. You can only modify the TPM Status, TPM Activation, and Intel

TXT fields if the TPM Status field is set to either On with Pre-boot Measurements

or On without Pre-boot Measurements.

TPM Information Changes the operational state of the TPM. This option is set to No Change by

default.

TPM Status Specifies the TPM status.

TPM Command CAUTION: Clearing the TPM results in the loss of all keys in the TPM. The

loss of TPM keys may affect booting to the operating system.

Clears all the contents of the TPM. The TPM Clear option is set to No by default.

Intel TXT Enables or disables the Intel Trusted Execution Technology (TXT) option. To enable

the Intel TXT option, virtualization technology and TPM Security must be enabled

with Pre-boot measurements. This option is set to Off by default.

Power Button Enables or disables the power button on the front of the system. This option is set

to Enabled by default.

Option Description

NMI Button Enables or disables the NMI button on the front of the system. This option is set to

Disabled by default.

AC Power

Recovery

Sets how the system behaves after AC power is restored to the system. This option

is set to Last by default.

AC Power

Recovery Delay

Sets the time delay for the system to power up after AC power is restored to the

system. This option is set to Immediate by default.

User Defined

Delay (60s to

240s)

Sets the User Defined Delay option when the User Defined option for AC Power

Recovery Delay is selected.

UEFI Variable

Access

Provides varying degrees of securing UEFI variables. When set to Standard (the

default), UEFI variables are accessible in the operating system per the UEFI

specification. When set to Controlled, selected UEFI variables are protected in the

environment and new UEFI boot entries are forced to be at the end of the current

boot order.

Secure Boot Enables Secure Boot, where the BIOS authenticates each pre-boot image by using

the certificates in the Secure Boot Policy. Secure Boot is disabled by default.

Secure Boot

Policy

When Secure Boot policy is set to Standard, the BIOS uses the system

manufacturer’s key and certificates to authenticate pre-boot images. When Secure

Boot policy is set to Custom, the BIOS uses the user-defined key and certificates.

Secure Boot policy is set to Standard by default.

Secure Boot

Policy Summary

Specifies the list of certificates and hashes that secure boot uses to authenticate

images.

Related Links

System Security

Viewing System Security

Secure Boot Custom Policy Settings

Secure Boot Custom Policy Settings is displayed only when Secure Boot Policy is set to Custom.

Viewing Secure Boot Custom Policy Settings

To view the Secure Boot Custom Policy Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Security.

5. On the System Security screen, click Secure Boot Custom Policy Settings.

Secure Boot Custom Policy Settings details

The Secure Boot Custom Policy Settings screen details are explained as follows:

Option Description

Platform Key Imports, exports, deletes, or restores the platform key (PK).

Option Description

Key Exchange Key

Database

Enables you to import, export, delete, or restore entries in the Key Exchange Key

(KEK) Database.

Authorized

Signature

Database

Imports, exports, deletes, or restores entries in the Authorized Signature Database

(db).

Forbidden

Signature

Database

Imports, exports, deletes, or restores entries in the Forbidden Signature Database

(dbx).

Creating a system and setup password

Prerequisites

Ensure that the password jumper is enabled. The password jumper enables or disables the system

password and setup password features. For more information, see the System board jumper settings

section.

NOTE: If the password jumper setting is disabled, the existing system password and setup password

are deleted and you need not provide the system password to boot the system.

Steps

1. To enter System Setup, press F2 immediately after turning on or rebooting your system.

2. On the System Setup Main Menu screen, click System BIOS → System Security.

3. On the System Security screen, verify that Password Status is set to Unlocked.

4. In the System Password field, type your system password, and press Enter or Tab.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

A message prompts you to reenter the system password.

5. Reenter the system password, and click OK.

6. In the Setup Password field, type your setup password and press Enter or Tab.

A message prompts you to reenter the setup password.

7. Reenter the setup password, and click OK.

8. Press Esc to return to the System BIOS screen. Press Esc again.

A message prompts you to save the changes.

NOTE: Password protection does not take effect until the system reboots.

Related Links

System board jumper settings

System board jumpers and connectors

System Security

Using your system password to secure your system

If you have assigned a setup password, the system accepts your setup password as an alternate system

password.

Steps

1. Turn on or reboot your system.

2. Type the system password and press Enter.

Next steps

When Password Status is set to Locked, type the system password and press Enter when prompted at

reboot.

NOTE: If an incorrect system password is typed, the system displays a message and prompts you to

reenter your password. You have three attempts to type the correct password. After the third

unsuccessful attempt, the system displays an error message that the system has stopped

functioning and must be turned off. Even after you turn off and restart the system, the error

message is displayed until the correct password is entered.

Related Links

System Security

Deleting or changing system and setup password

Prerequisites

NOTE: You cannot delete or change an existing system or setup password if the Password Status is

set to Locked.

Steps

1. To enter System Setup, press F2 immediately after turning on or restarting your system.

2. On the System Setup Main Menu screen, click System BIOS → System Security.

3. On the System Security screen, ensure that Password Status is set to Unlocked.

4. In the System Password field, alter or delete the existing system password, and then press Enter or

Tab.

5. In the Setup Password field, alter or delete the existing setup password, and then press Enter or Tab.

If you change the system and setup password, a message prompts you to reenter the new password.

If you delete the system and setup password, a message prompts you to confirm the deletion.

6. Press Esc to return to the System BIOS screen. Press Esc again, and a message prompts you to save

the changes.

Related Links

System Security

Operating with a setup password enabled

If Setup Password is set to Enabled, type the correct setup password before modifying the system setup

options.

If you do not type the correct password in three attempts, the system displays the following message:

Invalid Password! Number of unsuccessful password attempts: <x> System Halted!

Must power down.

Even after you turn off and restart the system, the error message is displayed until the correct password is

typed. The following options are exceptions:

• If System Password is not set to Enabled and is not locked through the Password Status option, you

can assign a system password. For more information, see the System Security Settings screen section.

• You cannot disable or change an existing system password.

NOTE: You can use the password status option with the setup password option to protect the

system password from unauthorized changes.

Related Links

Viewing System Security

System Security

System Information

You can use the System Information screen to view system properties such as Service Tag, system model

name, and the BIOS version.

Related Links

System Information details

System BIOS

Viewing System Information

To view the System Information screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Information.

Related Links

System Information

System Information details

The System Information screen details are explained as follows:

Option Description

System Model

Name

Specifies the system model name.

System BIOS

Version

Specifies the BIOS version installed on the system.

System

Management

Engine Version

Specifies the current version of the Management Engine firmware.

System Service

Tag

Specifies the system Service Tag.

System

Manufacturer

Specifies the name of the system manufacturer.

Option Description

System

Manufacturer

Contact

Information

Specifies the contact information of the system manufacturer.

System CPLD

Version

Specifies the current version of the system complex programmable logic device

(CPLD) firmware.

UEFI Compliance

Version

Specifies the UEFI compliance level of the system firmware.

Related Links

System Information

System Information details

Viewing System Information

Memory Settings

You can use the Memory Settings screen to view all the memory settings and enable or disable specific

memory functions, such as system memory testing and node interleaving.

Related Links

Memory Settings details

System BIOS

Viewing Memory Settings

To view the Memory Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Memory Settings.

Related Links

Memory Settings

Memory Settings details

The Memory Settings screen details are explained as follows:

Option Description

System Memory

Size

Specifies the memory size in the system.

System Memory

Type

Specifies the type of memory installed in the system.

System Memory

Speed

Specifies the system memory speed.

Option Description

System Memory

Voltage

Specifies the system memory voltage.

Video Memory Specifies the amount of video memory.

System Memory

Testing

Specifies whether the system memory tests are run during system boot. Options

are Enabled and Disabled. This option is set to Disabled by default.

Memory

Operating Mode

Specifies the memory operating mode. The options available are Optimizer Mode,

Advanced ECC Mode, Mirror Mode, Spare Mode, Spare with Advanced ECC Mode,

Dell Fault Resilient Mode and Dell NUMA Fault Resilient Mode. This option is set

to Optimizer Mode by default.

NOTE: The Memory Operating Mode option can have different default and

available options based on the memory configuration of your system.

NOTE: The Dell Fault Resilient Mode option establishes an area of memory

that is fault resilient. This mode can be used by an operating system that

supports the feature to load critical applications or enables the operating

system kernel to maximize system availability.

Node Interleaving Specifies if Non-Uniform Memory architecture (NUMA) is supported. If this field is

set to Enabled, memory interleaving is supported if a symmetric memory

configuration is installed. If the field is set to Disabled, the system supports NUMA

(asymmetric) memory configurations. This option is set to Disabled by default.

Snoop Mode Specifies the Snoop Mode options. The Snoop Mode options available are Home

Snoop, Early Snoop, and Cluster on Die. This option is set to Early Snoop by

default. This field is available only when the Node Interleaving is set to Disabled.

Related Links

Memory Settings

Viewing Memory Settings

Processor Settings

You can use the Processor Settings screen to view the processor settings, and perform specific functions

such as enabling virtualization technology, hardware prefetcher, and logical processor idling.

Related Links

Processor Settings details

System BIOS

Viewing Processor Settings

To view the Processor Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Processor Settings.

Related Links

Processor Settings

Processor Settings details

The Processor Settings screen details are explained as follows:

Option Description

Logical Processor Enables or disables the logical processors and displays the number of logical

processors. If this option is set to Enabled, the BIOS displays all the logical

processors. If this option is set to Disabled, the BIOS displays only one logical

processor per core. This option is set to Enabled by default.

QPI Speed Enables you to control QuickPath Interconnect data rate settings.

Alternate RTID

(Requestor

Transaction ID)

Setting

Modifies Requestor Transaction IDs, which are QPI resources. This option is set to

Disabled by default.

NOTE: Enabling this option may negatively impact the overall system

performance.

Virtualization

Technology

Enables or disables the additional hardware capabilities provided for virtualization.

This option is set to Enabled by default.

Address

Translation

Service (ATS)

Defines the Address Translation Cache (ATC) for devices to cache the DMA

transactions. This option provides an interface between CPU and DMA Memory

Management to a chipset's Address Translation and Protection Table to translate

DMA addresses to host addresses. This option is set to Enabled by default.

Adjacent Cache

Line Prefetch

Optimizes the system for applications that need high utilization of sequential

memory access. This option is set to Enabled by default. You can disable this

option for applications that need high utilization of random memory access.

Hardware

Prefetcher

Enables or disables the hardware prefetcher. This option is set to Enabled by

default.

DCU Streamer

Prefetcher

Enables or disables the Data Cache Unit (DCU) streamer prefetcher. This option is

set to Enabled by default.

DCU IP Prefetcher Enables or disables the Data Cache Unit (DCU) IP prefetcher. This option is set to

Enabled by default.

Logical Processor

Idling

Enables you to improve the energy efficiency of a system. It uses the operating

system core parking algorithm and parks some of the logical processors in the

system which in turn allows the corresponding processor cores to transition into a

lower power idle state. This option can only be enabled if the operating system

supports it. It is set to Disabled by default.

Configurable TDP Enables you to reconfigure the processor Thermal Design Power (TDP) levels

during POST based on the power and thermal delivery capabilities of the system.

TDP verifies the maximum heat the cooling system is needed to dissipate. This

option is set to Nominal by default.

NOTE: This option is only available on certain stock keeping units (SKUs) of the

processors.

X2Apic Mode Enables or disables the X2Apic mode.

Dell Controlled

Turbo

Controls the turbo engagement. Enable this option only when System Profile is set

to Performance.

Option Description

NOTE: Depending on the number of installed CPUs, there may be up to four

processor listings.

Number of Cores

per Processor

Controls the number of enabled cores in each processor. This option is set to All

by default.

Processor 64-bit

Support

Specifies if the processor(s) support 64-bit extensions.

Processor Core

Speed

Specifies the maximum core frequency of the processor.

Processor 1 NOTE: Depending on the number of CPUs, there may be up to four

processors listed.

The following settings are displayed for each processor installed in the system:

Option Description

Family-Model-

Stepping

Specifies the family, model, and stepping of the processor

as defined by Intel.

Brand Specifies the brand name.

Level 2 Cache Specifies the total L2 cache.

Level 3 Cache Specifies the total L3 cache.

Number of Cores Specifies the number of cores per processor.

Related Links

Processor Settings

Viewing Processor Settings

SATA Settings

You can use the SATA Settings screen to view the SATA settings of SATA devices and enable RAID on

your system.

Related Links

SATA Settings details

System BIOS

Viewing SATA Settings

To view the SATA Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click SATA Settings.

Related Links

SATA Settings

SATA Settings details

The SATA Settings screen details are explained as follows:

Option Description

Embedded SATA Enables the embedded SATA option to be set to Off, ATA, AHCI, or RAID modes.

This option is set to AHCI by default.

Security Freeze

Lock

Sends Security Freeze Lock command to the Embedded SATA drives during POST.

This option is applicable only for ATA and AHCI modes.

Write Cache Enables or disables the command for Embedded SATA drives during POST.

Port A Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port B Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port C Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Option Description

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port D Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port E Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port F Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port G Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

Option Description

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port H Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port I Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Port J Sets the drive type of the selected device. For Embedded SATA settings in ATA

mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS

support.

For AHCI or RAID mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Option Description

Capacity Specifies the total capacity of the hard drive. This field is

undefined for removable media devices such as optical

drives.

Related Links

SATA Settings

Viewing SATA Settings

Integrated Devices

You can use the Integrated Devices screen to view and configure the settings of all integrated devices

including the video controller, integrated RAID controller, and the USB ports.

Related Links

Integrated Devices details

System BIOS

Viewing Integrated Devices

To view the Integrated Devices screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Integrated Devices.

Related Links

Integrated Devices

Integrated Devices details

The Integrated Devices screen details are explained as follows:

Option Description

USB 3.0 Setting Enables or disables the USB 3.0 support. Enable this option only if your operating

system supports USB 3.0. If you disable this option, devices operate at USB 2.0

speed. USB 3.0 is enabled by default.

User Accessible

USB Ports

Enables or disables the USB ports. Selecting Only Back Ports On disables the front

USB ports, selecting All Ports Off disables all USB ports. The USB keyboard and

mouse operate during boot process in certain operating systems. After the boot

process is complete, the USB keyboard and mouse do not work if the ports are

disabled.

NOTE: Selecting Only Back Ports On and All Ports Off disables the USB

management port and also restricts access to iDRAC features.

Option Description

Internal USB Port Enables or disables the internal USB port. This option is set to Enabled by default.

Integrated RAID

Controller

Enables or disables the integrated RAID controller. This option is set to Enabled by

default.

Integrated

Network Card 1

Enables or disables the integrated network card.

Embedded NIC1

and NIC2 NOTE: The Embedded NIC1 and NIC2 options are only available on systems

that do not have Integrated Network Card 1.

Enables or disables the Embedded NIC1 and NIC2 options. If set to Disabled, the

NIC may still be available for shared network access by the embedded

management controller. The embedded NIC1 and NIC2 options are only available

on systems that do not have Network Daughter Cards (NDCs). The Embedded NIC1

and NIC2 option is mutually exclusive with the Integrated Network Card 1 option.

Configure the Embedded NIC1 and NIC2 option by using the NIC management

utilities of the system.

I/OAT DMA Engine Enables or disables the I/OAT option. Enable only if the hardware and software

support the feature.

Embedded Video

Controller

Enables or disables the Embedded Video Controller option. This option is set to

Enabled by default.

Current State of

Embedded Video

Controller

Displays the current state of the embedded video controller. The Current State of

Embedded Video Controller option is a read-only field. If the Embedded Video

Controller is the only display capability in the system (that is, no add-in graphics

card is installed), then the Embedded Video Controller is automatically used as the

primary display even if the Embedded Video Controller setting is set to Disabled.

SR-IOV Global

Enable

Enables or disables the BIOS configuration of Single Root I/O Virtualization (SR-

IOV) devices. This option is set to Disabled by default.

OS Watchdog

Timer

If your system stops responding, this watchdog timer aids in the recovery of your

operating system. When this option is set to Enabled, the operating system

initializes the timer. When this option is set to Disabled (the default), the timer does

not have any effect on the system.

Memory Mapped

I/O above 4 GB

Enables or disables the support for PCIe devices that need large amounts of

memory. This option is set to Enabled by default.

Slot Disablement Enables or disables the available PCIe slots on your system. The slot disablement

feature controls the configuration of PCIe cards installed in the specified slot. Slots

must be disabled only when the installed peripheral card prevents booting into the

operating system or causes delays in system startup. If the slot is disabled, both the

Option ROM and UEFI drivers are disabled.

Related Links

Integrated Devices

Viewing Integrated Devices

Serial Communication

You can use the Serial Communication screen to view the properties of the serial communication port.

Related Links

Serial Communication details

System BIOS

Viewing Serial Communication

To view the Serial Communication screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Serial Communication.

Related Links

Serial Communication

Serial Communication details

The Serial Communication screen details are explained as follows:

Option Description

Serial

Communication Selects serial communication devices (Serial Device 1 and Serial Device 2) in BIOS.

BIOS console redirection can also be enabled and the port address can be

specified. This option is set to Auto by default.

Serial Port

Address

Enables you to set the port address for serial devices. This option is set to Serial

Device 1=COM2, Serial Device 2=COM1 by default.

NOTE: You can use only Serial Device 2 for the Serial Over LAN (SOL) feature.

To use console redirection by SOL, configure the same port address for

console redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX setting

saved in iDRAC. The serial MUX setting can independently be changed in

iDRAC. Loading the BIOS default settings from within the BIOS setup utility

may not always revert the serial MUX setting to the default setting of Serial

Device 1.

External Serial

Connector

Enables you to associate the External Serial Connector to Serial Device 1, Serial

Device 2, or the Remote Access Device by using this option.

NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use

console redirection by SOL, configure the same port address for console

redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX setting

saved in iDRAC. The serial MUX setting can independently be changed in

iDRAC. Loading the BIOS default settings from within the BIOS setup utility

may not always revert this setting to the default setting of Serial Device 1.

Failsafe Baud Rate Specifies the failsafe baud rate for console redirection. The BIOS attempts to

determine the baud rate automatically. This failsafe baud rate is used only if the

Option Description

attempt fails, and the value must not be changed. This option is set to 115200 by

default.

Remote Terminal

Type

Sets the remote console terminal type. This option is set to VT 100/VT 220 by

default.

Redirection After

Boot

Enables or disables the BIOS console redirection when the operating system is

loaded. This option is set to Enabled by default.

Related Links

Serial Communication

Viewing Serial Communication

System Profile Settings

You can use the System Profile Settings screen to enable specific system performance settings such as

power management.

Related Links

System Profile Settings details

System BIOS

Viewing System Profile Settings

To view the System Profile Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Profile Settings.

Related Links

System Profile Settings

System Profile Settings details

The System Profile Settings screen details are explained as follows:

Option Description

System Profile Sets the system profile. If you set the System Profile option to a mode other than

Custom, the BIOS automatically sets the rest of the options. You can only change

the rest of the options if the mode is set to Custom. This option is set to

Performance Per Watt Optimized (DAPC) by default. DAPC is Dell Active Power

Controller.

NOTE: All the parameters on the system profile setting screen are available

only when the System Profile option is set to Custom.

CPU Power

Management

Sets the CPU power management. This option is set to System DBPM (DAPC) by

default. DBPM is Demand-Based Power Management.

Option Description

Memory

Frequency

Sets the speed of the system memory. You can select Maximum Performance,

Maximum Reliability, or a specific speed.

Turbo Boost Enables or disables the processor to operate in the turbo boost mode. This option

is set to Enabled by default.

Energy Efficient

Turbo

Enables or disables the Energy Efficient Turbo option.

Energy Efficient Turbo (EET) is a mode of operation where a processor’s core

frequency is adjusted to be within the turbo range based on workload.

C1E Enables or disables the processor to switch to a minimum performance state when

it is idle. This option is set to Enabled by default.

C States Enables or disables the processor to operate in all available power states. This

option is set to Enabled by default.

Collaborative CPU

Performance

Control

Enables or disables the CPU power management option. When set to Enabled, the

CPU power management is controlled by the OS DBPM and the System DBPM

(DAPC). This option is set to Disabled by default.

Memory Patrol

Scrub

Sets the memory patrol scrub frequency. This option is set to Standard by default.

Memory Refresh

Rate

Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.

Uncore Frequency Enables you to select the Processor Uncore Frequency option.

Dynamic mode enables the processor to optimize power resources across the

cores and uncore during runtime. The optimization of the uncore frequency to

either save power or optimize performance is influenced by the setting of the

Energy Efficiency Policy option.

Energy Efficient

Policy

Enables you to select the Energy Efficient Policy option.

The CPU uses the setting to manipulate the internal behavior of the processor and

determines whether to target higher performance or better power savings.

Number of Turbo

Boot Enabled

Cores for

Processor 1

NOTE: If there are two processors installed in the system, you see an entry for

Number of Turbo Boost Enabled Cores for Processor 2.

Controls the number of turbo boost enabled cores for processor 1. The maximum

number of cores is enabled by default.

Monitor/Mwait Enables the Monitor/Mwait instructions in the processor. This option is set to

Enabled for all system profiles, except Custom by default.

NOTE: This option can be disabled only if the C States option in the Custom

mode is set to disabled.

NOTE: When C States is set to Enabled in the Custom mode, changing the

Monitor/Mwait setting does not impact the system power or performance.

Related Links

System Profile Settings

Viewing System Profile Settings

Miscellaneous Settings

You can use the Miscellaneous Settings screen to perform specific functions such as updating the asset

tag and changing the system date and time.

Related Links

Miscellaneous Settings details

System BIOS

Viewing Miscellaneous Settings

To view the Miscellaneous Settings screen, perform the following steps:

1. Turn on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish

booting, and then restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Miscellaneous Settings.

Related Links

Miscellaneous Settings

Miscellaneous Settings details

The Miscellaneous Settings screen details are explained as follows:

Option Description

System Time Enables you to set the time on the system.

System Date Enables you to set the date on the system.

Asset Tag Specifies the asset tag and enables you to modify it for security and tracking

purposes.

Keyboard

NumLock

Enables you to set whether the system boots with the NumLock enabled or

disabled. This option is set to On by default.

NOTE: This option does not apply to 84-key keyboards.

F1/F2 Prompt on

Error

Enables or disables the F1/F2 prompt on error. This option is set to Enabled by

default. The F1/F2 prompt also includes keyboard errors.

Load Legacy

Video Option

ROM

Enables you to determine whether the system BIOS loads the legacy video (INT

10H) option ROM from the video controller. Selecting Enabled in the operating

system does not support UEFI video output standards. This field is available only for

UEFI boot mode. You cannot set the option to Enabled if UEFI Secure Boot mode

is enabled.

Related Links

Miscellaneous Settings

Viewing Miscellaneous Settings

iDRAC Settings utility

The iDRAC settings utility is an interface to set up and configure the iDRAC parameters by using UEFI. You

can enable or disable various iDRAC parameters by using the iDRAC settings utility.

NOTE: Accessing some of the features on the iDRAC settings utility needs the iDRAC Enterprise

License upgrade.

For more information about using iDRAC, see Dell Integrated Dell Remote Access Controller User's Guide

at Dell.com/idracmanuals.

Related Links

Device Settings

System BIOS

Entering the iDRAC Settings utility

Changing the thermal settings

Entering the iDRAC Settings utility

1. Turn on or restart the managed system.

2. Press F2 during Power-on Self-test (POST).

3. On the System Setup Main Menu page, click iDRAC Settings.

The iDRAC Settings screen is displayed.

Related Links

iDRAC Settings utility

Changing the thermal settings

The iDRAC settings utility enables you to select and customize the thermal control settings for your

system.

1. Click iDRAC Settings → Thermal.

2. Under SYSTEM THERMAL PROFILE → Thermal Profile, select one of the following options:

• Default Thermal Profile Settings

• Maximum Performance (Performance Optimized)

• Minimum Power (Performance per Watt Optimized)

3. Under USER COOLING OPTIONS, set the Fan Speed Offset, Minimum Fan Speed, and Custom

Minimum Fan Speed.

4. Click Back → Finish → Yes.

Related Links

iDRAC Settings utility

Device Settings

Device Settings enables you to configure device parameters.

Related Links

System BIOS

Dell Lifecycle Controller

Dell Lifecycle Controller (LC) provides advanced embedded systems management capabilities including

system deployment, configuration, update, maintenance, and diagnosis. LC is delivered as part of the

iDRAC out-of-band solution and Dell system embedded Unified Extensible Firmware Interface (UEFI)

applications.

Related Links

Embedded system management

The Dell Lifecycle Controller provides advanced embedded systems management throughout the

system’s lifecycle. The Dell Lifecycle Controller can be started during the boot sequence and can

function independently of the operating system.

NOTE: Certain platform configurations may not support the full set of features provided by the Dell

Lifecycle Controller.

For more information about setting up the Dell Lifecycle Controller, configuring hardware and firmware,

and deploying the operating system, see the Dell Lifecycle Controller documentation at Dell.com/

idracmanuals.

Related Links

Dell Lifecycle Controller

Boot Manager

The Boot Manager screen enables you to select boot options and diagnostic utilities.

Related Links

Boot Manager main menu

System BIOS

Viewing Boot Manager

To enter Boot Manager:

1. Turn on, or restart your system.

2. Press F11 when you see the following message:

F11 = Boot Manager

If your operating system begins to load before you press F11, allow the system to complete the

booting, and then restart your system and try again.

Related Links

Boot Manager

Boot Manager main menu

Menu item Description

Continue Normal

Boot

The system attempts to boot to devices starting with the first item in the boot

order. If the boot attempt fails, the system continues with the next item in the boot

order until the boot is successful or no more boot options are found.

One-shot Boot

Enables you to access boot menu, where you can select a one-time boot device to

boot from.

Launch System

Setup

Enables you to access System Setup.

Launch Lifecycle

Controller

Exits the Boot Manager and invokes the Dell Lifecycle Controller program.

System Utilities Enables you to launch System Utilities menu such as System Diagnostics and UEFI

shell.

Related Links

Boot Manager

Viewing Boot Manager

One-shot BIOS boot menu

One-shot BIOS boot menu enables you to select a one-shot boot device to boot from the following

options:

• Launch Diagnostics

• BIOS Update File Explorer

• Reboot System

Related Links

Boot Manager

System Utilities

System Utilities contains the following utilities that can be launched:

• Launch Diagnostics

• BIOS Update File Explorer

• Reboot System

Related Links

Boot Manager

PXE boot

The Preboot Execution Environment (PXE) is an industry standard client or interface that allows

networked computers that are not yet loaded with an operating system to be configured and booted

remotely by an administrator.

Installing and removing system

components

Safety instructions

WARNING: Whenever you need to lift the system, get others to assist you. To avoid injury, do not

attempt to lift the system by yourself.

WARNING: Opening or removing the system cover while the system is powered on may expose

you to a risk of electric shock.

CAUTION: Do not operate the system without the cover for a duration exceeding five minutes.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: Operating the system without the system cover can result in component damage.

NOTE: Dell recommends that you always use a static mat and static strap while working on

components inside the system.

NOTE: To ensure proper operation and cooling, all bays in the system and system fans must be

populated always with either a component or with a blank.

Before working inside your system

Prerequisites

Follow the safety guidelines listed in the Safety instructions section.

Steps

1. Turn off the system, including any attached peripherals.

2. Disconnect the system from the electrical outlet and disconnect the peripherals.

3. If installed, remove the front bezel.

4. If applicable, remove the system from the rack.

For more information, see the Rack Installation placemat at Dell.com/poweredgemanuals.

5. Remove the system cover.

Related Links

Safety instructions

Removing the system cover

Removing the optional front bezel

After working inside your system

Prerequisites

Follow the safety guidelines listed in the Safety instructions section.

Steps

1. Install the system cover.

2. If applicable, install the system into the rack.

For more information, see the Rack Installation placemat at Dell.com/poweredgemanuals.

3. If removed, install the optional front bezel.

4. Reconnect the peripherals and connect the system to the electrical outlet.

5. Turn on the system, including any attached peripherals.

Related Links

Installing the system cover

Installing the optional front bezel

Recommended tools

You need the following tools to perform the removal and installation procedures:

• Key to the bezel lock. This is needed only if your system includes a bezel.

• Phillips #1 screwdriver

• Phillips #2 screwdriver

• Wrist grounding strap

You need the following tools to assemble the cables for a DC power supply unit.

• AMP 90871-1 hand-crimping tool or equivalent

• Tyco Electronics 58433-3 or equivalent

• Wire-stripper pliers to remove insulation from size 10 AWG solid or stranded, insulated copper wire

NOTE: Use alpha wire part number 3080 or equivalent (65/30 stranding).

Front bezel (optional)

The front bezel is attached to the front side of the server and prevents accidents while removing the hard

drive or when pressing the reset or power button. The front bezel can also be locked for additional

security.

Removing the optional front bezel

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

Steps

1. Locate and remove the bezel key.

NOTE: The bezel key is attached to the back of the bezel.

2. Unlock the bezel by using the key.

3. Slide the release latch up and pull the left end of the bezel.

4. Unhook the right end, and remove the bezel.

Figure 16. Removing the optional front bezel

1. bezel lock 2. front bezel

Figure 17. Removing the Quick Sync bezel

1. bezel lock 2. Quick Sync bezel

Related Links

Safety instructions

Installing the optional front bezel

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

Steps

1. Locate and remove the bezel key.

NOTE: The bezel key is attached to the back of the bezel.

2. Hook the right end of the bezel onto the chassis.

3. Fit the free end of the bezel onto the system.

4. Lock the bezel by using the key.

Figure 18. Installing the optional front bezel

1. bezel lock 2. front bezel

Figure 19. Installing the Quick Sync bezel

1. bezel lock 2. Quick Sync bezel

Related Links

Safety instructions

Removing the optional front bezel

System cover

The system cover protects the components inside the system and helps in maintaining air flow inside the

system. Removing the system cover actuates the intrusion switch which aids in maintaining system

security.

Removing the system cover

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. Turn off the system, including any attached peripherals.

3. Disconnect the system from the electrical outlet and disconnect the peripherals.

4. If installed, remove the optional bezel. For more information, see the Removing the optional front

bezel section.

Steps

1. Rotate the latch release lock counter clockwise to the unlocked position.

2. Lift the latch toward the back of the system.

The system cover slides back and the tabs on the system cover disengage from the slots on the

chassis.

NOTE: The position of the latch may vary depending on the configuration of your system.

3. Hold the cover on both sides, and lift the cover away from the system.

Figure 20. Removing the system cover

1. latch release lock 2. latch

3. system cover

Next steps

1. Install the system cover.

Related Links

Safety instructions

Removing the optional front bezel

Installing the system cover

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. Ensure that all internal cables are connected and placed out of the way and no tools or extra parts

are left inside the system.

Steps

1. Align the slots on the system cover with the tabs on the chassis.

2. Push the system cover latch down to move the system cover into the closed position.

The system cover slides forward and the tabs on the system cover engage with the slots on the

chassis. The system cover latch locks into place when the system cover engages with the slots on

the chassis.

3. Rotate the latch release lock clockwise to the locked position.

Figure 21. Installing the system cover

1. latch release lock 2. latch

3. system cover

Next steps

1. If removed, install the bezel.

2. Reconnect the peripherals and connect the system to the electrical outlet.

3. Turn on the system, including any attached peripherals.

Related Links

Safety instructions

Installing the optional front bezel

Removing the system cover

Inside the system

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: Components that are hot swappable are marked orange and touch points on the

components are marked blue.

Figure 22. Inside the system—eight hard drive system

1. control panel assembly 2. cooling fans (7)

3. processor 1 4. DIMMs (6)

5. power supply unit (PSU) connector 6. PSU (2)

7. riser card 3 8. network daughter card

9. riser card 2 10. riser card 1

11. DIMMs (6) 12. processor 2

13. DIMMs (12) 14. hard drive backplane

15. hard drive

Figure 23. Inside the system—24 hard drive system and 10 hard drive system

1. control panel assembly 2. cooling fans (7)

3. processor 1 4. DIMMs (6)

5. PSU connector 6. PSU 2

7. riser card 3 8. network daughter card

9. riser card 1 10. riser card 2

11. DIMMs (6) 12. processor 2

13. DIMMs (12) 14. expander board

15. hard drive

Cooling shroud

The cooling shroud has aerodynamically placed openings that direct the airflow across the entire system.

The airflow passes through all the critical parts of the system, where the vacuum pulls air across the

entire surface area of the heat sink, thus allowing increased cooling.

Removing the cooling shroud

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: Never operate your system with the cooling shroud removed. The system may get

overheated quickly, resulting in shutdown of the system and loss of data.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

Steps

Holding the touch points, lift the cooling shroud away from the system.

Figure 24. Removing the cooling shroud

1. cooling shroud

Next steps

1. Install the cooling shroud.

2. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Installing the cooling shroud

After working inside your system

Installing the cooling shroud

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. If applicable, route the cables inside the system along the chassis wall and secure the cables by using

the cable-securing bracket.

Steps

1. Align the tabs on the cooling shroud with the securing slots on the chassis.

2. Lower the cooling shroud into the chassis until it is firmly seated.

Figure 25. Installing the cooling shroud

1. cooling shroud

Next steps

1. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

After working inside your system

Removing the cooling shroud

System memory

The system supports DDR4 registered DIMMs (RDIMMs) and load reduced DIMMs (LRDIMMs). System

memory holds the instructions that are executed by the processor.

NOTE: MT/s indicates DIMM speed in MegaTransfers per second.

Memory bus operating frequency can be 1866 MT/s, 2133 MT/s, or 2400 MT/s depending on the

following factors:

• DIMM type (RDIMM or LRDIMM)

• Number of DIMMs populated per channel

• System profile selected (for example, Performance Optimized, Custom, or Dense Configuration

Optimized)

• Maximum supported DIMM frequency of the processors

Your system contains 24 memory sockets split into two sets of 12 sockets, one set per processor. Each

12-socket set is organized into four channels. In each channel, the release tabs of the first socket are

marked white, the second socket black, and the third socket green.

Figure 26. Memory socket locations

Memory channels are organized as follows:

Table 36. Memory channels

Process

or Channel 0 Channel 1 Channel 2 Channel 3

Process

or 1

Slots A1, A5, and A9 Slots A2, A6, and A10 Slots A3, A7, and A11 Slots A4, A8, and A12

Process

or 2

Slots B1, B5, and B9 Slots B2, B6, and B10 Slots B3, B7, and B11 Slots B4, B8, and B12

The following table shows the memory populations and operating frequencies for the supported

configurations:

Table 37. Memory population

DIMM

Type DIMMs

Populated/

Channel Voltage Operating

Frequency (in MT/s) Maximum DIMM Rank/

Channel

RDIMM 1

1.2 V

2400, 2133, 1866 Dual rank or single rank

2 2400, 2133, 1866 Dual rank or single rank

3 1866 Dual rank or single rank

LRDIMM 1

1.2 V

2400, 2133, 1866 Quad rank

2 2400, 2133, 1866 Quad rank

3 2133, 1866 Quad rank

General memory module installation guidelines

NOTE: Memory configurations that fail to observe these guidelines can prevent your system from

booting, stop responding during memory configuration, or operating with reduced memory.

The system supports Flexible Memory Configuration, enabling the system to be configured and run in any

valid chipset architectural configuration. The following are the recommended guidelines for installing

memory modules:

• RDIMMs and LRDIMMs must not be mixed.

• x4 and x8 DRAM based memory modules can be mixed. For more information, see the Mode-specific

guidelines section.

• Up to three dual- or single-rank RDIMMs can be populated per channel.

• Up to three LRDIMMs can be populated per channel regardless of rank count.

• If memory modules with different speeds are installed, they will operate at the speed of the slowest

installed memory module(s) or slower depending on system DIMM configuration.

• Populate memory module sockets only if a processor is installed. For single-processor systems,

sockets A1 to A12 are available. For dual-processor systems, sockets A1 to A12 and sockets B1 to B12

are available.

• Populate all the sockets with white release tabs first, followed by the black release tabs, and then the

green release tabs.

• When mixing memory modules with different capacities, populate the sockets with memory modules

with highest capacity first. For example, if you want to mix 4 GB and 8 GB memory modules, populate

8 GB memory modules in the sockets with white release tabs and 4 GB memory modules in the

sockets with black release tabs.

• In a dual-processor configuration, the memory configuration for each processor should be identical.

For example, if you populate socket A1 for processor 1, then populate socket B1 for processor 2, and

so on.

• Memory modules of different capacities can be mixed provided other memory population rules are

followed (for example, 4 GB and 8 GB memory modules can be mixed).

• Mixing of more than two memory module capacities in a system is not supported.

• Populate four memory modules per processor (one DIMM per channel) at a time to maximize

performance.

Related Links

Mode-specific guidelines

Four memory channels are allocated to each processor. The allowable configurations depend on the

memory mode selected.

Advanced Error Correction Code (lockstep)

Advanced Error Correction Code (ECC) mode extends SDDC from x4 DRAM based DIMMs to both x4 and

x8 DRAMs. This protects against single DRAM chip failures during normal operation.

The installation guidelines for memory modules are as follows:

• Memory modules must be identical in size, speed, and technology.

• DIMMs installed in memory sockets with white release levers must be identical and the same rule

applies for sockets with black release levers. This ensures that identical DIMMs are installed in

matched pair —for example, A1 with A2, A3 with A4, A5 with A6, and so on.

Memory optimized (independent channel) mode

This mode supports Single Device Data Correction (SDDC) only for memory modules that use x4 device

width. It does not impose any specific slot population requirements.

Memory sparing

NOTE: To use memory sparing, this feature must be enabled in System Setup.

In this mode, one rank per channel is reserved as a spare. If persistent correctable errors are detected on

a rank, the data from this rank is copied to the spare rank, and the failed rank is disabled.

With memory sparing enabled, the system memory available to the operating system is reduced by one

rank per channel. For example, in a dual-processor configuration with sixteen 4 GB single-rank memory

modules, the available system memory is: 3/4 (ranks/channel) × 16 (memory modules) × 4 GB = 48 GB,

and not 16 (memory modules) × 4 GB = 64 GB.

NOTE: Memory sparing does not offer protection against a multi-bit uncorrectable error.

NOTE: Both Advanced ECC/Lockstep and Optimizer modes support memory sparing.

Memory mirroring

Memory mirroring offers the strongest memory module reliability mode compared to all other modes,

providing improved uncorrectable multi-bit failure protection. In a mirrored configuration, the total

available system memory is one half of the total installed physical memory. Half of the installed memory

is used to mirror the active memory modules. In the event of an uncorrectable error, the system switches

over to the mirrored copy. This ensures SDDC and multi-bit protection.

The installation guidelines for memory modules are as follows:

• Memory modules must be identical in size, speed, and technology.

• Memory modules installed in memory module sockets with white release levers must be identical and

the same rule applies for sockets with black and green release tabs. This ensures that identical

memory modules are installed in matched pairs—for example, A1 with A2, A3 with A4, A5 with A6, and

so on.

Table 38. Processor configuration

Processor Configuration Memory population

rules Memory population

information

Single CPU Memory population order {1,2}, {3,4} See Memory mirroring note

Sample memory configurations

The following tables show sample memory configurations for one and two processor configurations that

follow the appropriate memory guidelines.

NOTE: 1R, 2R, and 4R in the following tables indicate single, dual, and quad-rank DIMMs

respectively.

Table 39. Memory configurations—single processor

System

capacity

(in GB)

DIMM

size (in

GB)

Number

of DIMMs DIMM rank, organization, and

frequency DIMM slot population

4 4 1 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

8 4 2 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2

16 4 4 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4

8 2 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2

24 4 6 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6

48 4 12 1R, x8, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12

8 6 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6

System

capacity

(in GB)

DIMM

size (in

GB)

Number

of DIMMs DIMM rank, organization, and

frequency DIMM slot population

96 8 12 1R, x8, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12

16 6 2R, x8, 2400 MT/s

2R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6

128 16 8 2R, x8, 2400 MT/s

2R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8

144 8 10 1R, x8, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A11*

16 10 2R, x8, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A11*

256 32 8 2R, x4, 2400 MT/s

2R, x4, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8

384 32 12 2R, x4, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12

512 64 8 4R, x4, 2133 MT/s

4R, x4, 2400 MT/s

A1, A2, A3, A4, A5, A6, A7, A8

768 64 12 4R, x4, 1866 MT/s

4R, x4, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12

* 16 GB DIMMs must be installed in slots numbered A1, A2, A3, A4, A5, A6, A7, and A8 and 8 GB DIMMs

must be installed in slots A9 and A11.

Table 40. Memory configurations—two processors

System

capacity

(in GB)

DIMM

size (in

GB)

Number

of DIMMs DIMM rank, organization, and

frequency DIMM slot population

16 4 4 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, B1, B2

32 4 8 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4, B1, B2, B3, B4

64 4 16 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8, B1,

B2, B3, B4, B5, B6, B7, B8

System

capacity

(in GB)

DIMM

size (in

GB)

Number

of DIMMs DIMM rank, organization, and

frequency DIMM slot population

881R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4, B1, B2, B3, B4

96 4 24 1R, x8, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12, B1, B2, B3, B4, B5,

B6, B7, B8, B9, B10, B11, B12

8 12 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6, B1, B2, B3,

B4, B5, B6

128 8 16 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8, B1,

B2, B3, B4, B5, B6, B7, B8

16 8 2R, x8, 2400 MT/s

2R, x8, 2133 MT/s

A1, A2, A3, A4, B1, B2, B3, B4

160 8 20 1R, x8, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A11, B1, B2, B3, B4, B5, B6, B7, B8,

B9, B11

8 12 1R, x8, 2400 MT/s

1R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6, B1, B2, B3,

B4, B5, B6 *

16 12 2R, x8, 2400 MT/s

2R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6, B1, B2, B3,

B4, B5, B6 *

192 8 24 1R, x8, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12, B1, B2, B3, B4, B5,

B6, B7, B8, B9, B10, B11, B12

16 12 2R, x8, 2400 MT/s

2R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6, B1, B2, B3,

B4, B5, B6

256 16 16 2R, x8, 2400 MT/s

2R, x8, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8, B1,

B2, B3, B4, B5, B6, B7, B8

384 16 24 2R, x8, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12, B1, B2, B3, B4, B5,

B6, B7, B8, B9, B10, B11, B12

32 12 2R, x4, 2400 MT/s

2R, x4, 2133 MT/s

A1, A2, A3, A4, A5, A6, B1, B2, B3,

B4, B5, B6

System

capacity

(in GB)

DIMM

size (in

GB)

Number

of DIMMs DIMM rank, organization, and

frequency DIMM slot population

512 32 16 2R, x4, 2400 MT/s

2R, x4, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8, B1,

B2, B3, B4, B5, B6, B7, B8

64 8 4R, x4, 2400 MT/s

4R, x4, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8, B1,

B2, B3, B4, B5, B6, B7, B8

768 32 24 2R, x4, 1866 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12, B1, B2, B3, B4, B5,

B6, B7, B8, B9, B10, B11, B12

64 16 4R, x4, 2400 MT/s

4R, x4, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12, B1, B2, B3, B4, B5,

1024 64 16 4R, x4, 2133 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12, B1, B2, B3, B4, B5,

1536 64 24 4R, x4, 1866 MT/s

4R, x4, 2133 MT/s

A1, A2, A3, A4, A5, A6, A7, A8, A9,

A10, A11, A12, B1, B2, B3, B4, B5,

B6, B7, B8, B9, B10, B11, B12

* 16 GB DIMMs must be installed in slots numbered A1, A2, A3, A4, B1, B2, B3, and B4 and 8 GB DIMMs

must be installed in slots A5, A6, B5, and B6.

Removing memory modules

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Remove the cooling shroud.

WARNING: The memory modules are hot to touch for some time after the system has been

powered down. Allow the memory modules to cool before handling them. Handle the memory

modules by the card edges and avoid touching the components or metallic contacts on the

memory module.

CAUTION: To ensure proper system cooling, memory module blanks must be installed in any

memory socket that is not occupied. Remove memory module blanks only if you intend to install

memory modules in those sockets.

Steps

1. Locate the appropriate memory module socket.

CAUTION: Handle each memory module only by the card edges, ensuring not to touch the

middle of the memory module or metallic contacts.

2. To release the memory module from the socket, simultaneously press the ejectors on both ends of

the memory module socket.

3. Lift and remove the memory module from the system.

Figure 27. Removing the memory module

1. memory module 2. memory module socket

3. memory module socket ejector (2)

Next steps

1. If you are removing the memory module permanently, install a memory-module blank.

2. Install the memory module.

3. Install the cooling shroud.

4. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

Installing memory modules

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Remove the cooling shroud.

4. Removing the cooling fan assembly.

WARNING: The memory modules are hot to touch for some time after the system has been

powered down. Allow the memory modules to cool before handling them. Handle the memory

modules by the card edges and avoid touching the components or metallic contacts on the

memory module.

CAUTION: To ensure proper system cooling, memory module blanks must be installed in any

memory socket that is not occupied. Remove memory module blanks only if you intend to install

memory modules in those sockets.

Steps

1. Locate the appropriate memory module socket.

CAUTION: Handle each memory module only by the card edges, ensuring not to touch the

middle of the memory module or metallic contacts.

2. Align the edge connector of the memory module with the alignment key of the memory module

socket, and insert the memory module in the socket.

CAUTION: Do not apply pressure at the center of the memory module; apply pressure at both

ends of the memory module evenly.

NOTE: The memory module socket has an alignment key that enables you to install the

memory module in the socket in only one orientation.

3. Press the memory module with your thumbs until the socket levers firmly click into place.

When the memory module is properly seated in the socket, the levers on the memory module socket

align with the levers on the other sockets that have memory modules installed.

Figure 28. Installing the memory module

1. memory module 2. alignment key

3. memory module socket ejector (2)

Next steps

1. Install the cooling shroud.

2. Follow the procedure listed in the After working inside your system section.

3. Press F2 to enter System Setup, and check the System Memory setting.

The system should have already changed the value to reflect the installed memory.

4. If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure

that the memory module is firmly seated in the memory module socket.

5. Run the system memory test in system diagnostics.

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

After working inside your system

Installing the cooling shroud

Removing memory modules

Hard drives

All hard drives connect to the system board through the hard drive backplane. Hard drives are supplied in

hot swappable hard drive carriers that fit in the hard drive slots.

CAUTION: Before attempting to remove or install a hard drive while the system is running, see the

documentation for the storage controller card to ensure that the host adapter is configured

correctly to support hot swappable hard drive removal and insertion.

CAUTION: Do not turn off or reboot your system while the hard drive is being formatted. Doing

so can cause a hard drive failure.

NOTE: Use only hard drives that have been tested and approved for use with the hard drive

backplane.

When you format a hard drive, allow enough time for the formatting to be completed. High-capacity

hard drives can take several hours to format.

Removing a 2.5-inch hard drive blank

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. Perform

troubleshooting and simple repairs as authorized in your product documentation, or as directed

by the online or telephone service and support team. Damage due to servicing that is not

authorized by Dell is not covered by your warranty. Read and follow the safety instructions that

came with the product.

CAUTION: To maintain proper system cooling, all empty hard drive slots must have hard drive

blanks installed.

1. Follow the safety guidelines listed in the Safety instructions section.

2. If installed, remove the bezel.

Steps

Press the release button and slide the hard drive blank out of the hard drive slot.

Figure 29. Removing a 2.5-inch hard drive blank

1. hard drive blank 2. release button

Related Links

Safety instructions

Removing the optional front bezel

Installing a 2.5-inch hard drive blank

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. If installed, remove the front bezel.

Steps

Insert the hard drive blank into the hard drive slot until the release button clicks into place.

Figure 30. Installing a 2.5-inch hard drive blank

1. hard drive blank

Next steps

If removed, install the front bezel.

Related Links

Safety instructions

Removing the optional front bezel

Installing the optional front bezel

Removing a 1.8-inch hard drive blank

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. If installed, remove the front bezel.

CAUTION: To maintain proper system cooling, all empty hard drive slots must have hard drive

blanks installed.

Steps

Press the release button and slide the hard drive blank out of the hard drive slot.

Figure 31. Removing a 1.8-inch hard drive blank

1. hard drive blank 2. release button

Next steps

If applicable, install the front bezel.

Related Links

Safety instructions

Removing the optional front bezel

Installing a 1.8-inch hard drive blank

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. If installed, remove the front bezel.

Steps

Insert the hard drive blank into the hard drive slot until the release button clicks into place.

Next steps

If applicable, install the front bezel.

Figure 32. Installing a 1.8-inch hard drive blank

1. hard drive blank

Related Links

Safety instructions

Removing the optional front bezel

Installing the optional front bezel

Removing a hot swappable hard drive or SSD

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. If applicable, remove the bezel.

4. Using the management software, prepare the hard drive for removal. If the hard drive is online, the

green activity or fault indicator flashes while the drive is turning off. When the hard drive indicators

are off, the hard drive is ready for removal.

For more information, see the documentation for the storage controller.

CAUTION: To prevent data loss, ensure that your operating system supports hot-swap drive

installation. See the documentation supplied with your operating system.

Steps

1. Press the release button to open the hard drive or SSD carrier release handle.

2. Slide the hard drive carrier or SSD out of the hard drive slot.

CAUTION: To maintain proper system cooling, all empty hard drive or SSD slots must have

hard drive or SSD blanks installed.

3. If you are not replacing the hard drive or SSD immediately, insert a hard drive or SSD blank in the

empty hard drive slot.

100

Figure 33. Removing a hot swappable hard drive or SSD

1. release button 2. hard drive or SSD carrier

3. hard drive or SSD carrier handle

Figure 34. Removing a 1.8 inch hot-swappable uSATA SSD carrier

1. release button 2. SSD carrier

3. SSD carrier handle

Related Links

Safety instructions

Removing the optional front bezel

101

Installing a hot swappable hard drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: Use only hard drives that have been tested and approved for use with the hard drive

backplane.

CAUTION: Combining SAS and SATA hard drives in the same RAID volume is not supported.

CAUTION: When installing a hard drive, ensure that the adjacent drives are fully installed.

Inserting a hard drive carrier and attempting to lock its handle next to a partially installed carrier

can damage the partially installed carrier's shield spring and make it unusable.

CAUTION: To prevent data loss, ensure that your operating system supports hot-swap drive

installation. See the documentation supplied with your operating system.

CAUTION: When a replacement hot swappable hard drive is installed and the system is powered

on, the hard drive automatically begins to rebuild. Make absolutely sure that the replacement

hard drive is blank or contains data that you wish to have over-written. Any data on the

replacement hard drive is immediately lost after the hard drive is installed.

1. Follow the safety guidelines listed in Safety instructions section.

Steps

1. If a hard drive blank is installed in the hard drive slot, remove it.

2. Install a hard drive in the hard drive carrier. For more information, see the Installing a hot swappable

hard drive into a hot swappable hard drive carrier section.

3. Press the release button on the front of the hard drive carrier and open the hard drive carrier handle.

4. Insert the hard drive carrier into the hard drive slot until the carrier connects with the backplane.

5. Close the hard drive carrier handle to lock the hard drive in place.

Next steps

Install the optional front bezel.

102

Figure 35. Installing a hot swappable hard drive

1. release button 2. hard drive or SSD carrier

3. hard drive or SSD carrier handle

Figure 36. Installing a 1.8-inch hot swappable uSATA SSD

1. release button 2. SSD carrier

3. SSD carrier handle

Related Links

Safety instructions

Installing a hot swappable hard drive into a hot swappable hard drive carrier

Installing the optional front bezel

Removing a hard drive from a hard drive carrier

Prerequisites

1. Keep the Phillips #1 screwdriver handy.

103

2. Remove the hard drive carrier from the system.

Steps

1. Remove the screws from the slide rails on the hard drive carrier.

2. Lift the hard drive out of the hard drive carrier.

Figure 37. Removing a hard drive into a hard drive carrier

1. screw (4) 2. hard drive

3. hard drive carrier

Installing a hot swappable hard drive into a hot swappable hard drive carrier

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: Hot swappable hard drives are supplied in hot swappable hard drive carriers that fit in the

hard drive slots.

1. Keep the Phillips #2 screwdriver ready.

2. Remove the hot swappable hard drive carrier.

Steps

1. Insert the hot swappable hard drive into the hard drive carrier with the connector end of the hard

drive toward the back.

2. Align the screw holes on the hard drive with the set of screw holes on the hard drive carrier.

When aligned correctly, the back of the hard drive is flush with the back of the hard drive carrier.

3. Attach the screws to secure the hard drive to the hard drive carrier.

Next steps

Install the hard drive carrier into the system.

104

Figure 38. Installing a hot swappable hard drive into a hot swappable hard drive carrier

1. screw (4) 2. hard drive

3. hard drive carrier

Removing a 1.8-inch hard drive from a hard drive carrier

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. Remove the hard drive carrier from the system.

Steps

1. Turn the hard drive carrier.

2. Pull the rails of the hard drive carrier and lift the hard drive out of the hard drive carrier.

Figure 39. Removing a 1.8-inch hard drive into a hard drive carrier

1. hard drive carrier 2. hard drive

Related Links

Safety instructions

105

Installing a 1.8-inch hard drive into a hard drive carrier

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

Insert the hard drive into the hard drive carrier with the connector end of the hard drive toward the

back.

When aligned correctly, the back of the hard drive is flush with the back of the hard drive carrier.

Figure 40. Installing a 1.8-inch hard drive into a hard drive carrier

1. hard drive carrier 2. hard drive

Optical drive (optional)

Optical drives retrieve and store data on optical discs such as compact disks(CD), digital versatile disks

(DVD), and Blu-ray discs (BD). Optical drives can be categorized into two basic types: optical disk readers

and optical disk writers.

Removing the optional optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: This procedure applies only to the eight hard drive system.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

106

Steps

1. Disconnect the power and data cable from the back of the drive.

NOTE: Ensure that you note the routing of the power and data cable on the side of the system

as you remove them from the system board and drive. Route these cables properly when you

replace them to prevent them from being pinched or crimped.

2. To release the optical drive, press the release tab.

3. Slide the optical drive out of the system until it is free of the optical drive slot.

4. If you are not adding a new optical drive, install the optical drive blank.

Figure 41. Removing the optional optical drive

1. optical drive 2. power and data cable

3. release tab

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

After working inside your system

Installing the optional optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: This procedure applies only to the eight hard drive system.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

107

Steps

1. Align the optical drive with the optical drive slot on the front of the chassis.

2. Slide in the optical drive until the release tab snaps into place.

3. Connect the power and data cable to the optical drive and system board.

NOTE: Route the cable properly on the side of the system to prevent it from being pinched or

crimped.

Figure 42. Installing the optional optical drive

1. optical drive 2. power and data cable

3. release tab

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

After working inside your system

Removing the optional optical drive

Removing the slim optical drive blank

To remove the slim optical drive, follow the same procedure.

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

108

Steps

1. Locate the touch point for the slim optical drive blank lock inside the system.

2. Press the lock and pull the slim optical drive blank out of the chassis.

Figure 43. Removing the slim optical drive blank

1. slim optical drive blank 2. optical drive blank lock

Related Links

Safety instructions

Before working inside your system

Installing the slim optical drive blank

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Follow the safety instructions listed in the Safety instructions section.

Steps

1. Align the slim optical drive blank with the slim optical drive bay.

2. Slide the optical drive blank into the optical drive bay until the lock clicks into place.

Next steps

Follow the procedure listed in the After working inside your system section.

109

Figure 44. Installing the slim optical drive blank

1. slim optical drive blank 2. optical drive blank lock

Related Links

Safety instructions

After working inside your system

Removing the slim optical drive blank

Cooling fans

Your system supports seven hot swappable cooling fans.

NOTE: In the event of a problem with a particular fan, the fan number is referenced by the system

management software, allowing you to easily identify and replace the proper fan by noting the fan

numbers on the cooling fan assembly.

Removing a cooling fan

Prerequisites

WARNING: Opening or removing the system cover when the system is ON may expose you to a

risk of electric shock. Exercise utmost care while removing or installing cooling fans.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: The cooling fans are hot swappable. To maintain proper cooling while the system is

on, replace only one fan at a time.

CAUTION: Do not operate the system with the cover removed for a duration exceeding five

minutes.

NOTE: The procedure for removing each fan is identical.

110

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

Steps

Hold the fan and lift it out of the system.

Next steps

Figure 45. Removing a cooling fan

1. cooling fan (7) 2. connector on the system board (7)

Related Links

Safety instructions

Before working inside your system

Installing a cooling fan

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

NOTE: Your system supports seven hot-swappable cooling fans.

NOTE: The procedure for installing each fan is identical.

Steps

1. Align the connector at the base of the cooling fan with the connector on the system board.

2. Slide the cooling fan into the securing slot until the tab locks into place.

111

Figure 46. Installing a cooling fan

1. cooling fan (7) 2. connector on the system board (7)

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

After working inside your system

Removing a cooling fan

Internal USB memory key (optional)

An optional USB memory key installed inside your system can be used as a boot device, security key, or

mass storage device.

To boot from the USB memory key, configure the USB memory key with a boot image and then specify

the USB memory key in the boot sequence in System Setup.

The internal USB port must be enabled in Internal USB Port option in the Integrated Devices screen of

System Setup.

NOTE: To locate the internal USB port J_USB_INT on the system board, see the System board

jumpers and connectors section.

Related Links

System board jumpers and connectors

Replacing the optional internal USB memory key

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

112

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

Steps

1. Locate the USB port or USB key on the system board.

To locate the USB port, see the System board jumpers and connectors section.

2. If installed, remove the USB key from the USB port.

Figure 47. Removing the internal USB key

1. USB memory key 2. USB port

3. Insert the replacement USB key into the USB port.

Figure 48. Installing the internal USB key

1. USB memory key 2. USB port

Next steps

1. Follow the procedure listed in the After working inside your system section.

2. While booting, press F2 to enter System Setup and verify that the system detects the USB key.

Related Links

Safety instructions

System board jumpers and connectors

Before working inside your system

After working inside your system

System Setup

113

Expansion cards and expansion card riser

An expansion card in the computer is an add-on card that can be inserted into an expansion slot on the

computer system board or riser card to add enhanced functionality to the system through the expansion

bus.

NOTE: A System Event Log (SEL) event is logged if an expansion card riser is unsupported or

missing. It does not prevent your system from turning on and no BIOS POST message or F1/F2

pause is displayed.

Expansion card installation guidelines

Your system supports PCI Express Generation 3 expansion cards.

Table 41. Guidelines for systems supporting three PCIe expansion cards

Riser PCIe Slot Processor

Connection Height Length Link

Width Slot Width

1 1 Processor 2 Low Profile Half Length x16 x16

1 2 Processor 2 Low Profile Half Length x8 x16

3 3 Processor 1 Low Profile Half Length x16 x16

NOTE: Both the processors must be installed to use riser 1 slots.

Table 42. Guidelines for systems supporting two PCIe expansion cards

Riser PCIe Slot Processor

Connection Height Length Link

Width Slot Width

2 1 Processor 1 Low Profile Half Length x8 x16

Processor 2 Low Profile Half Length x16 x16

3 2 Processor 1 Full height Three-fourth

Length

x16 x16

NOTE: Only a three-fourth length card is supported for the PCIe expansion card slot (slot 2) on riser

3 when no mini-PERC card is installed. Supported length with mini-PERC card installed is half

length.

NOTE: For a system with three PCIe cards, only MiniSAS HD third-party cards are supported in slot

3. For a system with two PCIe cards, only MiniSAS HD third-party cards are supported in slot 1.

NOTE: You can install expansion cards only on one slot on riser 2.

NOTE: Both the processors must be installed to use the x16 PCIe link on the riser 2 slot.

The following table provides a guide for installing expansion cards to ensure proper cooling and

mechanical fit. Install the expansion card by following the card priority and slot priority order as shown in

the table.

114

Table 43. Expansion card installation priority

Card Priority Card Type Systems Supporting up to 2

PCIe Expansion Cards Systems Supporting up to 3 PCIe

Expansion Cards

Slot Priority Max Allowed Slot Priority Max Allowed

1 PCIe Bridge N/A N/A 1 1

2 RAID 1 1 3, 1 2

3 100 G HCA/OPA

HFI

1 1 3, 2 (3, 1 for

CX4/OPA)

4 40 G NICs 2, 1 2 3, 2 2

5 FC16 HBA 2, 1 2 3, 2, 1 3

6 10 Gb NICs 2, 1 2 3, 2, 1 3

7 FC8 HBA 2, 1 2 3, 2, 1 3

8 1 Gb NICs 2, 1 2 3, 2, 1 3

9 Non-RAID 12 Gb

SAS

1 1 3, 1 2

10 Integrated RAID Integrated Slot 1 Integrated Slot 1

11 NDC Integrated Slot 1 Integrated Slot 1

12 NVMe PCIe SSD 1,2 2 3, 2, 1 2

NOTE: To support x16 PCIe link width, the 100 G HCA/OPA HFI in slot 1 needs processor 2 and x16

center_riser2.

Removing expansion card risers

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: The expansion card riser 1 and the x16 link on the riser 2 slot can be used only when both

the processors are installed.

Steps

1. Holding the touch points, lift the expansion card riser from the riser connector on the system board.

115

Figure 49. Removing the expansion card riser 1

1. expansion card riser 1 2. connector

3. riser guide pin

Figure 50. Removing the expansion card riser 3

1. expansion card release latch 2. expansion card riser 3

3. connector

2. If applicable, remove or install an expansion card on the riser.

3. Install the expansion card riser.

116

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Installing an expansion card

Installing expansion card risers

After working inside your system

Removing an expansion card

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Disconnect any cables connected to the expansion card or expansion card riser.

2. To remove the expansion card, lift the expansion card latch.

3. Hold the expansion card by its edges and remove it from the expansion card connector on the riser.

4. If you are removing the card permanently, install a metal filler bracket over the empty expansion slot

opening and close the expansion card latch.

NOTE: You must install a filler bracket over an empty expansion card slot to maintain Federal

Communications Commission (FCC) certification of the system. The brackets also keep dust

and dirt out of the system and aid in proper cooling and airflow inside the system.

117

Figure 51. Removing an expansion card

1. expansion card connector 2. expansion card latch

3. expansion card 4. expansion card connector on the

system board

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

After working inside your system

Installing an expansion card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: The expansion card riser 1 and the x16 link on the riser 2 slot can be used only when both

the processors are installed.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Remove the expansion card riser.

Steps

1. Unpack the expansion card and prepare it for installation.

For instructions, see the documentation that accompanied the card.

2. Locate the expansion card connector on the system board or riser.

118

3. Open the expansion card latch and remove the filler bracket.

4. Holding the card by its edges, position the card so that the card edge connector aligns with the

expansion card connector.

5. Insert the card edge connector firmly into the expansion card connector until the card is fully seated.

6. Slide the expansion card latch into position.

Figure 52. Installing an expansion card

1. expansion card connector 2. expansion card latch

3. expansion card 4. expansion card connector on the

system board

7. Follow the procedure listed in the After working inside your system section.

8. Install any device drivers needed for the card as described in the documentation for the card.

Related Links

Removing expansion card risers

After working inside your system

Removing an expansion card

Installing expansion card risers

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

Steps

1. If removed, install the expansion cards into the expansion card riser.

2. Align the expansion card riser with the connector and the riser guide pin on the system board.

119

3. Lower the expansion card riser into place until the expansion card riser connector is fully seated in

the connector.

Figure 53. Installing the expansion card riser 1

1. expansion card riser 1 2. connector

3. riser guide pin

Figure 54. Installing the expansion card riser 3

1. expansion card release latch 2. expansion card riser 3

3. connector

120

Next steps

1. Follow the procedure listed in the After working inside your system section.

2. Install any device drivers needed for the card as described in the documentation for the card.

Related Links

Installing an expansion card

After working inside your system

Removing expansion card risers

SD vFlash media card (optional)

An SD vFlash card is a Secure Digital (SD) card that plugs into the SD vFlash card slot in the iDRAC port

card. It provides persistent on-demand local storage and a custom deployment environment that enables

automation of server configuration, scripts, and imaging. It emulates USB device(s). For more information,

see the Integrated Dell Remote Access Controller User's Guide at Dell.com/idracmanuals.

Replacing an SD vFlash card

Prerequisites

NOTE: This procedure applies only to the eight hard drive system.

Steps

1. Locate the vFlash media slot on the system.

2. To remove the installed SD vFlash card, push inward on the card to release it and pull the card from

the card slot.

Figure 55. Removing the SD vFlash card

1. SD vFlash card 2. SD vFlash card slot

3. To install the SD vFlash card, with the label side facing up, insert the contact-pin end of the SD card

into the card slot on the module.

NOTE: The slot is keyed to ensure correct insertion of the card.

4. Press inward on the card to lock it into the slot.

121

Figure 56. Installing the SD vFlash card

1. SD vFlash card 2. SD vFlash card slot

Internal dual SD module (optional)

The Internal Dual SD module (IDSDM) provides you with a redundant SD card solution. You can configure

the IDSDM for storage or as the OS boot partition. The IDSDM card offers the following features:

• Dual card operation — maintains a mirrored configuration by using SD cards in both the slots and

provides redundancy.

NOTE: When the Redundancy option is set to Mirror Mode in the Integrated Devices screen of

System Setup, the information is replicated from one SD card to another.

• Single card operation — single card operation is supported, but without redundancy.

Removing an internal SD Card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

Steps

Locate the SD card slot on the internal dual SD module or the backplane expander board and press

inward on the card to release it from the slot and remove the card.

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

After working inside your system

Installing an internal SD card

122

Installing an internal SD card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

NOTE: To use an SD card with your system, ensure that the internal SD card port is enabled in the

System Setup.

Steps

1. Locate the SD card connector on the internal dual SD module or the backplane expander board.

With the label side facing up, insert the contact-pin end of the card into the slot.

NOTE: The slot is keyed to ensure correct insertion of the card.

2. To lock the card into place, press it into the card slot.

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

After working inside your system

Removing an internal SD Card

Removing the optional internal dual SD module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. If installed, remove the SD cards.

NOTE: Temporarily label each SD card with its corresponding slot number before removal.

Reinstall the SD cards into the corresponding slots.

Steps

1. Locate the internal dual SD module (IDSDM) on the system board. To locate the internal dual SD

module connector, see the System board connectors section.

2. Holding the pull tab, lift the IDSDM out of the system.

123

Figure 57. Removing the internal dual SD module (IDSDM)

1. IDSDM 2. pull tab

3. LED status indicator (2) 4. SD card (2)

5. SD card slot 2 6. SD card slot 1

7. IDSDM connector

The following table describes the IDSDM indicator codes:

Table 44. IDSDM indicator codes

Convention IDSDM indicator code Description

A Green Indicates that the card is online.

B Flashing green Indicates rebuild or activity.

C Flashing amber Indicates card mismatch or that the card has

failed.

D Amber Indicates that the card is offline, has failed, or is

write protected.

124

Convention IDSDM indicator code Description

E Not lit Indicates that the card is missing or is booting.

Next steps

1. Install the IDSDM.

2. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Removing an internal SD Card

Installing the optional internal dual SD module

After working inside your system

Installing the optional internal dual SD module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

NOTE: Temporarily label each SD card with its corresponding slot before removal.

Steps

1. Locate the internal dual SD module (IDSDM) connector on the system board. To locate the internal

dual SD module connector, see the System board connectors section.

2. Align the IDSDM with the connector on the system board.

3. Push the IDSDM until it is firmly seated on the system board.

125

Figure 58. Installing the optional internal dual SD module

1. Internal Dual SD module 2. LED status indicator (2)

3. SD card (2) 4. SD card slot 2

5. SD card slot 1 6. IDSDM connector

Next steps

1. Install the SD cards.

NOTE: Re-install the SD cards into the same slots based on the labels you had marked on the

cards during removal.

2. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

System board jumpers and connectors

Before working inside your system

After working inside your system

Removing the optional internal dual SD module

126

Integrated storage controller card

Your system includes a dedicated expansion card slot on the system board for an integrated controller

card. The integrated storage controller card provides the integrated storage subsystem for the internal

hard drives in your system. The controller supports SAS and SATA hard drives and also enables you to set

up the hard drives in RAID configurations. The RAID configurations depend on the version of the storage

controller included with your system.

Removing the integrated storage controller card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Remove the cooling shroud.

4. Remove the expansion card riser 1.

5. Keep the Phillips #2 screwdriver ready.

Steps

1. Loosen the screws that secure the integrated storage controller cable to the integrated storage

controller card connector on the system board.

2. Lift the integrated storage controller cable away from the integrated storage controller.

3. Lift one end of the card and angle it to disengage the card from the integrated storage controller

card holder on the system board.

4. Lift the card out of the system.

127

Figure 59. Removing the integrated storage controller card

1. integrated storage controller cable 2. integrated storage controller card

3. integrated storage controller card

connector on the system board 4. integrated storage controller card

holder

Next steps

1. Install the expansion card riser 1.

2. Install the cooling shroud.

3. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

Removing expansion card risers

Installing expansion card risers

Installing the cooling shroud

After working inside your system

Installing the integrated storage controller card

128

Installing the integrated storage controller card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Remove the cooling shroud.

4. Remove the expansion card riser 1.

5. Keep the Phillips #2 screwdriver ready.

Steps

1. Align the end of the integrated storage controller card with the controller card connector on the

system board.

2. Lower the connector side of the integrated storage controller card into the integrated storage

controller card connector on the system board.

NOTE: Ensure that the tabs on the system board align with the screw holes on the integrated

storage controller card.

3. Align the screws on the integrated storage controller card cable with the screw holes on the

connector.

4. Tighten the screws to secure the integrated storage controller card cable with the integrated storage

controller card connector on the system board.

129

Figure 60. Installing the integrated storage controller card

1. integrated storage controller cable 2. integrated storage controller card

3. integrated storage controller card

connector on the system board 4. integrated storage controller card

holder

Next steps

1. Install the expansion card riser 1.

2. Install the cooling shroud.

3. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

Removing expansion card risers

Installing expansion card risers

Installing the cooling shroud

After working inside your system

Removing the integrated storage controller card

130

Network daughter card

The Network daughter card (NDC) is a small, removable mezzanine card. The NDC provides you with the

flexibility of choosing different network connectivity options, for example—4 x 1GbE, 2 x 10GbE and 2 x

Converged Network Adapter.

Removing the network daughter card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Keep the Philips #2 screwdriver handy.

Steps

1. Remove the expansion card riser 3.

2. Using a Phillips #2 screwdriver, loosen the two captive screws that secure the Network Daughter

Card (NDC) to the system board.

3. Hold the NDC by the edges on either side of the touch points and lift to remove it from the

connector on the system board.

4. Slide the NDC away from the back of the system until the Ethernet connectors are clear of the slot in

the back panel.

5. Lift the NDC out of the system.

131

Figure 61. Removing the NDC

1. captive screw socket (2) 2. connector on the system board

3. captive screw (2) 4. touch point (2)

5. NDC 6. back panel slots for Ethernet

connectors

Related Links

Safety instructions

Before working inside your system

Removing expansion card risers

Installing the network daughter card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: If the GPU card is installed, you cannot install the 10 GbE Network Daughter Card

(NDC).

132

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Keep the Philips #1 screwdriver handy.

NOTE: If the system has three PCIe cards, ensure that you install the PCIe cooling shroud in your

system.

Steps

1. Orient the NDC so that the Ethernet connectors fit through the slot in the back panel.

2. Align the captive screws at the back-end of the card with the screw holes on the system board.

3. To ensure that the connector on the card is in contact with the connector on the system board,

press the touch point on the card.

4. Tighten the two captive screws to secure the NDC to the system board.

5. Install the expansion card riser 3.

Figure 62. Installing the NDC

1. captive screw socket (2) 2. connector on the system board

3. captive screw (2) 4. touch point (2)

5. NDC 6. back panel slots for Ethernet

connectors

Next steps

Follow the procedure listed in the After working inside your system section.

133

Related Links

Safety instructions

Before working inside your system

Installing expansion card risers

After working inside your system

Removing the network daughter card

Processors and heat sinks

Use the following procedure when:

• Removing and installing a heat sink

• Installing an additional processor

• Replacing a processor

NOTE: To ensure proper system cooling, you must install a processor blank in any empty processor

socket.

Removing a heat sink

Prerequisites

CAUTION: Never remove the heat sink from a processor unless you intend to remove the

processor. The heat sink is necessary to maintain proper thermal conditions.

WARNING: The heat sink will be hot to touch. Allow the heat sink to cool for some time after

powering down the system.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Keep the Phillips #2 screwdriver ready.

3. Follow the procedure listed in the Before working inside your system section.

4. If installed, remove the full-length PCIe card(s).

5. Remove the cooling shroud.

Steps

1. Loosen one of the screws that secure the heat sink to the system board.

Allow some time (approximately 30 seconds) for the heat sink to loosen from the processor.

2. Remove the screw diagonally opposite the screw you first removed.

3. Repeat the procedure for the remaining two screws.

4. Remove the heat sink.

134

Figure 63. Removing a heat sink

1. retention screw (4) 2. heat sink

3. processor socket 4. retention screw slot (4)

Next steps

1. Replace the heat sink(s) and processor(s).

2. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

Installing a heat sink

Installing a processor

Removing a processor

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be

performed only by Dell certified service technicians.

NOTE: To ensure proper system cooling, you must install a processor blank in any empty processor

socket.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Keep the Phillips #2 screwdriver ready.

135

4. If installed, remove the full-length PCIe card(s).

5. Remove the cooling shroud.

6. Remove the heat sink.

7. If you are upgrading your system, download the latest system BIOS version from Dell.com/support

and follow the instructions included in the compressed download file to install the update on your

system.

NOTE: You can update the system BIOS by using the Dell Lifecycle Controller.

CAUTION: The processor is held in its socket under strong pressure. Be aware that the release

lever can spring up suddenly if not firmly grasped.

WARNING: The processor is hot to touch for some time after the system has been powered down.

Allow the processor to cool before removing it.

Steps

1. Release the open first socket lever near the unlock icon by pushing the lever down and out from

under the tab.

2. Release the close first socket release lever near the lock icon by pushing the lever down and out

from under the tab. Lift the lever 90 degrees upward.

3. Lower the open first socket-release lever to lift the processor shield.

4. Hold the tab on the processor shield and lift the processor shield until the open first socket-release

lever lifts up.

CAUTION: The socket pins are fragile and can be permanently damaged. Be careful not to

bend the pins in the socket when removing the processor out of the socket.

5. Lift the processor out of the socket and leave the open first socket-release lever up.

NOTE: If you are permanently removing the processor, you must install a socket protective cap

in the vacant socket to protect the socket pins and keep the socket free of dust.

NOTE: After removing the processor, place it in an anti-static container for reuse, return, or

temporary storage. Do not touch the bottom of the processor. Touch only the side edges of

the processor.

136

Figure 64. Processor shield

1. close first socket release lever 2. lock icon

3. processor 4. open first socket release lever

5. unlock icon

137

Figure 65. Removing and installing a processor

1. close first socket-release lever 2. pin-1 indicator of processor

3. processor 4. slot (4)

5. processor shield 6. open first socket-release lever

7. socket 8. socket keys (4)

Next steps

1. Replace the processor(s).

2. Install the heat sink.

3. Reinstall the cooling shroud.

4. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

Removing a heat sink

Installing a processor

Installing a heat sink

Installing the cooling shroud

After working inside your system

138

Installing a processor

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be

performed only by Dell certified service technicians.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Keep the Phillips #2 screwdriver ready.

4. If you are upgrading your system, download the latest system BIOS version from Dell.com/support

and follow the instructions included in the compressed download file to install the update on your

system.

NOTE: You can also update the system BIOS by using the Dell Lifecycle Controller.

5. If installed, remove the full-length PCIe card.

6. Remove the cooling shroud.

NOTE: If applicable, close the expansion card latch on the cooling shroud to release the full

length card.

WARNING: The heat sink and processor are too hot to touch for some time after the system has

been powered down. Allow the heat sink and processor to cool down before handling them.

CAUTION: Never remove the heat sink from a processor unless you intend to remove the

processor. The heat sink is necessary to maintain proper thermal conditions.

NOTE: If you are installing a single processor, it must be installed in socket CPU1.

Steps

1. Unpack the new processor.

NOTE: If the processor has previously been used in a system, remove any remaining thermal

grease from the processor by using a lint-free cloth.

2. Locate the processor socket.

3. If applicable, remove the socket protective cap.

4. Release the open first socket-release lever near the unlock icon by pushing the lever down and

out from under the tab.

5. Similarly, release the close first socket-release lever near the lock icon by pushing the lever down

and out from under the tab. Lift the lever 90 degrees upward.

6. Hold the tab near the lock symbol on the processor shield and lift it up and out of the way.

CAUTION: Positioning the processor incorrectly can permanently damage the system board

or the processor. Be careful not to bend the pins in the socket.

CAUTION: While removing or reinstalling the processor, wipe your hands of any

contaminants. Contaminants on the processor pins such as thermal grease or oil can damage

the processor.

139

7. Align the processor with the socket keys.

CAUTION: Do not use force to seat the processor. When the processor is positioned

correctly, it engages easily into the socket.

8. Align the pin-1 indicator of the processor with the triangle on the socket .

CAUTION: Do not use force to seat the processor. When the processor is positioned

correctly, it engages easily into the socket.

9. Place the processor on the socket such that the slots on the processor align with the socket keys.

10. Close the processor shield.

11. Lower the close first socket-release lever near the lock icon and push it under the tab to lock it.

12. Similarly, lower the open first socket-release lever near the unlock icon and push it under the tab

to lock it.

Next steps

NOTE: Ensure that you install the heat sink after you install the processor. The heat sink is necessary

to maintain proper thermal conditions.

1. Install the heat sink.

2. While booting, press F2 to enter System Setup and verify that the processor information matches the

new system configuration.

3. Run the system diagnostics to verify that the new processor operates correctly.

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

Installing a heat sink

Using system diagnostics

System Setup

Installing a heat sink

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Keep the Phillips #2 screwdriver ready.

3. Follow the procedure listed in the Before working inside your system section.

4. Remove the cooling shroud.

5. Install the processor.

Steps

1. If you are using an existing heat sink, remove the thermal grease from the heat sink by using a clean

lint-free cloth.

2. Use the thermal grease syringe included with your processor kit to apply the grease in a thin spiral on

the top of the processor.

140

CAUTION: Applying too much thermal grease can result in excess grease coming in contact

with and contaminating the processor socket.

NOTE: The thermal grease syringe is intended for one-time use only. Dispose of the syringe

after you use it.

Figure 66. Applying thermal grease on the top of the processor

1. processor 2. thermal grease

3. thermal grease syringe

3. Place the heat sink onto the processor.

4. Tighten one of the four screws to secure the heat sink to the system board.

5. Tighten the screw diagonally opposite to the first screw you have tightened.

NOTE: Do not over-tighten the heat sink retention screws when installing the heat sink. To

prevent over-tightening, tighten the retention screw until resistance is felt, and stop after the

screw is seated. The screw tension should not be more than 6 in-lb (6.9 kg-cm).

6. Repeat the procedure for the remaining two screws.

141

Figure 67. Installing the heat sink

1. retention screw (4) 2. heat sink

3. processor socket 4. retention screw slot (4)

Next steps

1. Install the cooling shroud.

2. If applicable, install the PCIe card.

3. Follow the procedure listed in the After working inside your system section.

4. While booting, press F2 to enter System Setup and verify that the processor information matches the

new system configuration.

5. Run the system diagnostics to verify that the new processor operates correctly.

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

Installing a processor

Installing the cooling shroud

After working inside your system

Power supply units

Your system supports one of the following:

• Two 495 W, 750 W, or 1100 W AC power supply units (PSUs)

• Two 1100 W DC PSUs

• Two 750 W mixed mode PSUs

CAUTION: For AC PSUs, use only PSUs with the Extended Power Performance (EPP) label on the

back. Mixing PSUs from previous generations of systems can result in a PSU mismatch condition

or failure to turn on.

142

NOTE: Titanium PSU is nominally rated for 200 V AC to 240 V AC input only.

NOTE: When two identical PSUs are installed, power supply redundancy (1+1 – with redundancy or

2+0 – without redundancy) is configured in system BIOS. In redundant mode, power is supplied to

the system equally from both PSUs when Hot Spare is disabled. When Hot Spare is enabled, one of

the PSUs will be put into standby when system utilization is low in order to maximize efficiency.

NOTE: If two PSUs are used, they must be of the same maximum output power.

Hot spare feature

Your system supports the hot spare feature that significantly reduces the power overhead associated with

power supply redundancy.

When the hot spare feature is enabled, one of the redundant PSUs is switched to the sleep state. The

active PSU supports 100 percent of the load, thus operating at higher efficiency. The PSU in the sleep

state monitors output voltage of the active PSU. If the output voltage of the active PSU drops, the PSU in

the sleep state returns to an active output state.

If having both PSUs active is more efficient than having one PSU in the sleep state, the active PSU can

also activate the sleeping PSU.

The default PSU settings are as follows:

• If the load on the active PSU is more than 50 percent, then the redundant PSU is switched to the

active state.

• If the load on the active PSU falls below 20 percent, then the redundant PSU is switched to the sleep

state.

You can configure the hot spare feature by using the iDRAC settings. For more information about iDRAC

settings, see the Integrated Dell Remote Access Controller User’s Guide available at Dell.com/

idracmanuals.

Removing the power supply unit blank

If you are installing a second power supply unit (PSU), remove the PSU blank in the bay by pulling the

blank outward.

CAUTION: To ensure proper system cooling, the power supply blank must be installed in the

second PSU bay in a non-redundant configuration. Remove the PSU blank only if you are

installing a second PSU.

143

Figure 68. Removing the PSU blank

1. PSU blank 2. PSU bay

Related Links

Installing the power supply unit blank

Install the power supply unit (PSU) blank only in the second PSU bay.

Align the PSU blank with the PSU bay and push it into the chassis until it clicks into place.

Figure 69. Installing the PSU blank

1. PSU blank 2. PSU bay

Related Links

Removing the power supply unit blank

144

Removing an AC power supply unit

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: The system needs one power supply for normal operation. On power-redundant

systems, remove and replace only one power supply at a time in a system that is powered on.

NOTE: You may have to unlatch and lift the optional cable management arm if it interferes with the

power supply unit (PSU) removal. For information about the cable management arm, see the

system’s rack documentation.

Steps

1. Disconnect the power cable from the power source and from the PSU you intend to remove, and

then remove the cables from the strap.

2. Press the release latch and slide the PSU out of the chassis by using the PSU handle.

Figure 70. Removing an AC PSU

1. release latch 2. PSU cable connector

3. PSU 4. power connector

5. PSU handle

Related Links

Installing an AC power supply unit

145

Installing an AC power supply unit

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: The maximum output power (shown in watts) is listed on the PSU label.

1. Follow the safety guidelines listed in the Safety instructions section.

2. For systems that support redundant power supply units (PSUs), ensure that both the PSUs are of the

same type and have the same maximum output power

3. If installed, remove the PSU blank.

Steps

1. Slide the new PSU into the chassis until the PSU is fully seated and the release latch snaps into place.

NOTE: If you unlatched the cable management arm, relatch it. For information about the cable

management arm, see the rack documentation of your system.

2. Connect the power cable to the PSU and plug the cable into a power outlet.

CAUTION: When connecting the power cable, secure the cable with the strap.

NOTE: When installing, hot swapping, or hot-adding a new PSU, wait for 15 seconds for the

system to recognize the PSU and determine its status. The power supply redundancy may not

occur until discovery is complete. Wait until the new PSU is discovered and enabled before you

remove the other PSU. The PSU status indicator turns green to signify that the PSU is

functioning properly.

Figure 71. Installing an AC PSU

1. release latch 2. PSU cable connector

3. PSU 4. power connector

146

5. PSU handle

Related Links

Safety instructions

Removing the power supply unit blank

Removing an AC power supply unit

Wiring instructions for a DC power supply unit

Your system supports up to two –(48–60) V DC power supply units (PSUs).

WARNING: For equipment using –(48–60) V DC power supply units (PSUs), a qualified electrician

must perform all connections to DC power and to safety grounds. Do not attempt connecting to

DC power or installing grounds yourself. All electrical wiring must comply with applicable local

or national codes and practices. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow all safety instructions that came with the product.

CAUTION: Wire the unit with copper only, unless otherwise specified, use only 10 American Wire

Gauge (AWG) wire rated minimum 90 ºC for source and return. Protect the –(48–60) V DC (1

wire) with a branch circuit over-current protection rated 50 A for DC with a high interrupt

current rating.

CAUTION: Connect the equipment to a –(48–60) V DC supply source that is electrically isolated

from the AC source (reliably grounded –(48–60) V DC SELV source). Ensure that the –(48–60) V

DC source is efficiently secured to earth (ground).

NOTE: A readily accessible disconnect device that is suitably approved and rated shall be

incorporated in the field wiring.

Input requirements

• Supply voltage: –(48–60) V DC

• Current consumption: 32 A (maximum)

Kit contents

• Dell part number 6RYJ9 terminal block or equivalent (1)

• #6-32 nut equipped with lock washer (1)

Required tools

Wire-stripper pliers capable of removing insulation from size 10 AWG solid or stranded, insulated copper

wire

NOTE: Use alpha wire part number 3080 or equivalent (65/30 stranding)

Required wires

• One UL 10 AWG, 2 m maximum (stranded) black wire [–(48–60) V DC]

• One UL 10 AWG, 2 m maximum (stranded) red wire (V DC return)

• One UL 10 AWG, 2 m maximum green/yellow, green with a yellow stripe, stranded wire (safety

ground)

147

Assembling and connecting the safety ground wire

Prerequisites

WARNING: For equipment using –(48–60) V DC power supply units (PSUs), a qualified electrician

must perform all connections to DC power and to safety grounds. Do not attempt connecting to

DC power or installing grounds yourself. All electrical wiring must comply with applicable local

or national codes and practices. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow all safety instructions that came with the product.

Steps

1. Strip the insulation from the end of the green/yellow wire, exposing approximately 4.5 mm (0.175

inch) of copper wire.

2. Using a hand-crimping tool (Tyco Electronics, 58433-3 or equivalent), crimp the ring-tongue

terminal (Jeeson Terminals Inc., R5-4SA or equivalent) to the green/yellow wire (safety ground wire).

3. Connect the safety ground wire to the grounding post on the back of the system using a #6-32 nut

equipped with a locking washer.

Figure 72. Assembling and connecting the safety ground wire

1. #6-32 nut 2. spring washer

3. grounding post 4. safety ground wire

Figure 73. Removing the safety ground wire

1. #6-32 nut 2. spring washer

148

3. grounding post 4. safety ground wire

Assembling the DC input power wires

Prerequisites

WARNING: For equipment using –(48–60) V DC power supply units (PSUs), a qualified electrician

must perform all connections to DC power and to safety grounds. Do not attempt connecting to

DC power or installing grounds yourself. All electrical wiring must comply with applicable local

or national codes and practices. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow all safety instructions that came with the product.

Steps

1. Strip the insulation from the ends of the DC power wires, exposing approximately 13 mm (0.5 inch)

of copper wire.

WARNING: Reversing polarity when connecting DC power wires can permanently damage

the power supply or the system.

2. Insert the copper ends into the mating connectors and tighten the captive screws at the top of the

mating connector using a Phillips #2 screwdriver.

WARNING: To protect the power supply from electrostatic discharge, the captive screws

must be covered with the rubber cap before inserting the mating connector into the power

supply.

3. Rotate the rubber cap clockwise to fix it over the captive screws.

4. Insert the mating connector into the PSU.

Figure 74. Assembling the DC Input Power Wires

1. DC wire RTN 2. DC power connector

3. captive screw (2) 4. rubber cap

5. DC power socket 6. DC wire –48 V

149

Figure 75. Removing the DC Input Power Wires

1. wire RTN 2. DC power connector

3. captive screw (2) 4. rubber cap

5. DC power socket 6. wire –48 V

Removing a DC power supply unit

Prerequisites

WARNING: For equipment using –(48–60) V DC power supply units (PSUs), a qualified electrician

must perform all connections to DC power and to safety grounds. Do not attempt connecting to

DC power or installing grounds yourself. All electrical wiring must comply with applicable local

or national codes and practices. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow all safety instructions that came with the product.

CAUTION: The system needs one power supply for normal operation. On power-redundant

systems, remove and replace only one power supply at a time in a system that is powered on.

NOTE: You may have to unlatch and lift the optional cable management arm if it interferes with

power supply removal. For information about the cable management arm, see the rack

documentation of your system.

Steps

1. Disconnect the power wires from the power source and the connector from the PSU you intend to

remove.

2. Disconnect the safety ground wire.

3. Press the release latch and slide the PSU out of the chassis by using the PSU handle.

150

Figure 76. Removing a DC PSU

1. release latch 2. power supply status indicator

3. PSU 4. power connector

5. PSU handle

Related Links

Installing a DC power supply unit

Prerequisites

WARNING: For equipment using –(48–60) V DC power supply units (PSUs), a qualified electrician

must perform all connections to DC power and to safety grounds. Do not attempt connecting to

DC power or installing grounds yourself. All electrical wiring must comply with applicable local

or national codes and practices. Damage due to servicing that is not authorized by Dell is not

covered by your warranty. Read and follow all safety instructions that came with the product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. If installed, remove the PSU blank.

4. Verify that both the PSUs are of the same type and have the same maximum output power.

NOTE: The maximum output power (shown in watts) is listed on the PSU label.

Steps

1. Slide the PSU into the chassis until the PSU is fully seated and the release latch snaps into place.

NOTE: If you have unlatched the cable management arm, relatch it. For information about the

cable management arm, see the system’s rack documentation.

2. Connect the safety ground wire.

3. Install the DC power connector in the PSU.

CAUTION: When connecting the power wires, ensure that you secure the wires with the strap

to the PSU handle.

151

4. Connect the wires to a DC power source.

NOTE: When installing, hot-swapping, or hot-adding a new PSU, wait for 15 seconds for the

system to recognize the PSU and determine its status. The PSU status indicator turns green to

signify that the PSU is functioning properly.

Figure 77. Installing a DC PSU

1. release latch 2. power supply status indicator

3. PSU 4. power connector

5. PSU handle

Next steps

• Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

Removing the power supply unit blank

Removing a DC power supply unit

System battery

The system board battery is used for low-level system functions like powering the real-time clock and

storing the computer’s BIOS settings.

Replacing the system battery

Prerequisites

WARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the

battery only with the same or equivalent type recommended by the manufacturer. For more

information, see the safety information that shipped with your system.

152

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Remove the cooling shroud.

Steps

1. Locate the battery socket. For more information, see the System board jumpers and connectors

section.

CAUTION: To avoid damage to the battery connector, you must firmly support the connector

while installing or removing a battery.

2. Place your finger between the securing tabs at the negative side of the battery connector and lift the

battery out of the socket.

Figure 78. Removing the system battery

1. system battery 2. system battery slot

3. To install a new system battery, hold the battery with the "+" facing up and slide it under the securing

tabs.

4. Press the battery into the connector until it snaps into place.

Figure 79. Installing the system battery

1. system battery 2. system battery slot

153

Next steps

1. Install the cooling shroud.

2. Follow the procedure listed in the After working inside your system section.

3. While booting, press F2 to enter System Setup and ensure the battery is operating properly.

4. Enter the correct time and date in the System Setup Time and Date fields.

5. Exit System Setup.

Related Links

Safety instructions

System board jumpers and connectors

Before working inside your system

Removing the cooling shroud

Installing the cooling shroud

After working inside your system

Hard drive backplane

Depending on the configuration, your system supports one of the following:

Eight hard drive

system supports

2.5-inch (x4) SAS/SATA backplane

10 hard drive

system supports

2.5-inch (x10) SAS/SATA backplane that supports X10 and 4 (PCIe SSDs)

24 hard drive

system supports

1.8-inch (x24) SAS/SATA backplane

Removing the hard drive backplane

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: To prevent damage to the hard drives and hard drive backplane, remove the hard

drives from the system before removing the hard drive backplane.

CAUTION: Note the number of each hard drive and temporarily label them before removal so that

you can replace them in the same locations.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Remove all hard drives.

Steps

1. Disconnect the SAS/SATA/SSD data cables and power cable from the backplane.

2. If applicable, disconnect the power and data cable from the optical drive.

3. Push the backplane blue release tabs in the direction of the arrows and lift the backplane upwards.

154

4. Pull the backplane away from the system until the securing slots on the backplane are free from the

tabs on the chassis.

Figure 80. Removing the 2.5-inch (x8) hard drive backplane

1. backplane signal cable 2. backplane signal cable

3. SAS A cable 4. release tabs (2)

5. SAS B cable 6. backplane

155

Figure 81. Cabling diagram—2.5-inch (x8) hard drive systems

1. SAS backplane 2. signal connector on system board

3. system board 4. SAS A connector on system board

5. SAS B connector on system board

156

Figure 82. Removing the 2.5-inch (x10) hard drive backplane

1. release tab 2. SD signal cable

3. SD signal cable connector 4. SAS cables (2)

5. SAS cable connector (2) 6. guide pin

7. guide pin slot 8. backplane

157

Figure 83. Cabling diagram—2.5-inch (x10) hard drive systems

1. SAS backplane expander card 2. signal cable connector on the system

board

3. system board 4. integrated storage controller card

158

Figure 84. Removing the 1.8-inch (x24) hard drive backplane

1. SD signal cable (3) 2. SD signal cable connector (2)

3. SAS cables (4) 4. SAS cable connector (4)

5. guide pin 6. guide pin slot

7. backplane 8. release tab (2)

159

Figure 85. Cabling diagram—1.8-inch (x24) hard drive systems

1. SAS backplane 2. SD signal cable connector

3. SAS backplane expander card 4. SD signal cable connector

5. SD signal cable connector 6. system board

7. integrated storage controller card 8. SAS connector on system board

9. SAS connector on system board

Related Links

Safety instructions

Before working inside your system

Installing the hard drive backplane

160

Installing the hard drive backplane

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Use the hooks on the chassis as guides to align the hard drive backplane.

2. Lower the hard drive backplane until the release tabs snap into place.

3. Connect the SAS/SATA/SSD data, signal, and power cables to the backplane.

Figure 86. Installing the 2.5-inch (x8) hard drive backplane

1. backplane signal cable 2. backplane signal cable

3. SAS A cable 4. release tabs (2)

5. SAS B cable 6. backplane

161

Figure 87. Installing the 2.5-inch (x10) hard drive backplane

1. release tab 2. SD signal cable

3. SD signal cable connector 4. SAS cables (2)

5. SAS cable connector (2) 6. guide pin

7. guide pin slot 8. backplane

Figure 88. Installing the 1.8-inch (x24) hard drive backplane

1. SD signal cable (3) 2. SD signal cable connector (2)

3. SAS cables (4) 4. SAS cable connector (4)

5. guide pin 6. guide pin slot

7. backplane 8. release tab (2)

Next steps

1. Install the hard drives in their original locations.

162

2. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Before working inside your system

After working inside your system

Removing the hard drive backplane

Getting help

Using system diagnostics

Control panel assembly

Removing the control panel board–eight hard drive system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: The display module connector is a ZIF (zero insertion force) connector. Ensure that the

locking tab on the connector is released before removal and insertion. The locking tab must be

engaged after insertion.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Keep the Philips #2 screwdriver ready.

Steps

1. Disconnect the control panel and display module cables from the control panel board.

2. Remove the two screws that secure the control panel board to the chassis.

3. Slide the control panel board toward the back and out of the system.

163

Figure 89. Removing the control panel board

1. control panel board 2. screws (2)

3. control panel cable 4. display module cable

Related Links

Safety instructions

Before working inside your system

Installing the control panel board–eight hard drive system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Keep the Philips #2 screwdriver ready.

Steps

1. Align the screw holes on the control panel board with the standoffs on the chassis.

2. Replace the two screws that secure the control panel board to the chassis.

CAUTION: The display module connector is a ZIF (zero insertion force) connector. Ensure

that the locking tab on the connector is released before removal and insertion. The locking

tab must be engaged after insertion.

3. Connect control panel and display module cables to the control panel board.

164

4. If required, route the power and data cables along the chassis wall.

Figure 90. Installing the control panel board

1. control panel board 2. screws (2)

3. control panel cable 4. display module cable

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

After working inside your system

Removing the control panel board–eight hard drive system

Removing the control panel–eight hard drive system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: The display module connector is a ZIF (zero insertion force) connector. Ensure that the

locking tab on the connector is released before removal and insertion. The locking tab must be

engaged after insertion.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Keep the Philips #1 screwdriver ready.

165

Steps

1. Disconnect the display module cable from the control panel board.

2. Remove the screw (located at the top of the chassis) that secures the control panel to the chassis.

CAUTION: Applying excessive force while pulling upward may damage the control panel.

NOTE: Apart from the screw, the control panel has three tabs (one on the left and two tabs on

top) that secure it to the chassis.

3. Hold the top edge of the control panel at the corners and pull upward until the control panel tabs are

released.

4. Hold the right edge of the control panel and rotate it toward the left until it is released from the

chassis.

5. Pull the control panel away from the chassis.

Figure 91. Removing the control panel for eight hard drive system

1. control panel 2. notch on chassis front wall (2)

3. display module ZIF connector 4. display module cable

Related Links

Safety instructions

Before working inside your system

Installing the control panel–eight hard drive system

166

Installing the control panel–eight hard drive system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Keep the Philips #1 screwdriver ready.

Steps

1. Slide the left side of the control panel into the chassis so that the left tab on the control panel aligns

with the slot on the chassis wall and the top left tab aligns with the slot on the top of the chassis.

2. Pull the display module cable through the opening and into the chassis.

3. Push the right side of the control panel until the top right tab aligns with the top of the chassis and

the panel snaps into place.

4. Using a Philips #1 screwdriver, replace the screw (located at the bottom of the chassis) that secures

the control module to the chassis.

CAUTION: The display module connector is a ZIF (zero insertion force) connector. Ensure

that the locking tab on the connector is released before removal and insertion. The locking

tab must be engaged after insertion.

5. Connect the display module cable to the control panel board.

167

Figure 92. Installing the control panel for eight hard drive system

1. control panel 2. notch on chassis front wall (2)

3. display module ZIF connector 4. display module cable

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

After working inside your system

Removing the control panel–eight hard drive system

Removing the control panel–10 hard drive and 24 hard drive system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Keep the Philips #1 screwdriver ready.

Steps

1. Remove the screw (located at the top of the chassis) that secures the control panel to the chassis.

2. Remove the control panel cable from the connectors on the system board (J_CP and J_FP_USB) and

the hard drive expander card.

168

NOTE: To locate the connectors on the system board, see the System board connectors

section.

3. Slide the control panel out of the chassis.

4. Disconnect the control panel cable from the control panel.

Figure 93. Removing the control panel for 10 and 24 hard drive system

1. control panel 2. screw hole

3. screw 4. cable securing clip

5. J_CP connector on the system board 6. J_FP_USB connector on the system

board

Related Links

Safety instructions

System board jumpers and connectors

Before working inside your system

Installing the control panel–10 hard drive system and 24 hard drive system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

1. Follow the safety guidelines listed in the Safety instructions section.

169

2. Keep the Philips #1 screwdriver ready.

Steps

1. Route the control panel cable through the chassis and connect the control panel cable to the

control panel.

2. Push the control panel into the chassis till it snaps into place.

NOTE: Ensure that the screw hole on the control panel aligns with the screw hole located at

the top of the chassis.

3. Replace the screw that secures the control panel to the chassis.

4. Locate the connectors J_CP and J_FP_USB on the system board.

NOTE: To locate the connectors on the system board, see the Jumpers and connectors

section.

5. Connect the control panel cable to the connectors on the system board (J_CP and J_FP_USB) and

the hard drive expander card.

NOTE: Ensure that the control panel cable inside the system is routed along the chassis wall

and secured by using the cable securing bracket.

Figure 94. Installing the control panel for 10 and 24 hard drive system

1. control panel 2. screw hole on the control panel

3. screw hole on the chassis 4. screw

5. cable securing clip 6. J_CP connector on the system board

7. J_FP_USB connector on the system

board

170

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

System board jumpers and connectors

After working inside your system

Removing the control panel–10 hard drive and 24 hard drive system

VGA module

NOTE: Only the eight hard drive system has a VGA module on the front panel.

Removing the VGA module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: The display module connector is a ZIF (zero insertion force) connector. Ensure that the

locking tab on the connector is released before removal and insertion. The locking tab must be

engaged after insertion.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Keep the Philips #2 screwdriver ready.

Steps

1. Disconnect the display module cable from the control panel board.

2. Remove the control panel.

3. Disconnect the VGA module cable from the VGA module.

4. Remove the screw that secures the VGA module to the chassis.

5. Slide the VGA module out of the chassis.

171

Figure 95. Removing the VGA Module

1. screw 2. VGA module cable

3. VGA module 4. control panel

Related Links

Safety instructions

Before working inside your system

Removing the control panel–10 hard drive and 24 hard drive system

Removing the control panel–eight hard drive system

Installing the VGA module

Safety instructions

Installing the VGA module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: This procedure applies only to the eight hard drive system.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Keep the Philips #2 screwdriver ready.

172

Steps

1. Push the VGA module into the chassis and align the threaded screw hole on the VGA module with

the screw hole on the chassis.

2. Replace the screw (at the bottom of the chassis) that secures the VGA module to the chassis.

3. Replace the control panel.

4. Connect the VGA module cable to the VGA module.

CAUTION: The display module connector is a ZIF (zero insertion force) connector. Ensure

that the locking tab on the connector is released before removal and insertion. The locking

tab must be engaged after insertion.

5. Connect the display module cables to the control panel board.

Figure 96. Installing the VGA module

1. screw 2. VGA module cable

3. VGA module 4. control panel

Next steps

Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

Installing the control panel–10 hard drive system and 24 hard drive system

Installing the control panel–eight hard drive system

After working inside your system

173

System board

Removing the system board

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

CAUTION: If you are using the Trusted Platform Module (TPM) with an encryption key, you may

be prompted to create a recovery key during program or System Setup. Be sure to create and

safely store this recovery key. If you replace this system board, supply the recovery key when you

restart your system or program before you can access the encrypted data on your hard drives.

CAUTION: Do not attempt to remove the TPM plug-in module from the system board. After the

TPM plug-in module is installed, it is cryptographically bound to that specific system board. Any

attempt to remove an installed TPM plug-in module breaks the cryptographic binding, and it

cannot be re-installed or installed on another system board.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

3. Remove the following:

a. Cooling shroud

b. Memory modules

c. Cooling fans

d. Power supply units

e. All expansion card risers and expansion cards

WARNING: The heat sink is hot to touch for some time after the system has been

powered down. Ensure that you do not touch the heat sinks while removing the system

board.

f. Heat sinks or heat sink blanks and processors or processor blanks

CAUTION: To prevent damage to the processor pins when replacing a faulty system

board, ensure that you cover the processor socket with the processor protective cap.

g. Integrated storage controller card

h. Network daughter card

i. Internal dual SD module

j. Internal USB key (if installed)

k. Hot-swap hard drives

l. Hard drive backplane

CAUTION: To avoid damaging the mini SAS cable and connector, follow the correct

procedure when removing the mini SAS cable from the system board.

174

Steps

1. Disconnect the mini SAS cable from the system board:

a. Push the mini SAS cable connector to slide it further into the connector on the system board.

b. Press down and hold the metal tab on the mini SAS cable connector.

c. Pull the mini SAS cable out of the connector on the system board.

2. Disconnect all other cables from the system board.

CAUTION: Do not to damage the system identification button while removing the system

board from the chassis.

3. Grasp the system board holder, lift the blue release pin, slide the system board toward the front of

the system, and lift the system board out of the chassis.

CAUTION: Do not lift the system board by holding a memory module, processor, or other

components.

175

Figure 97. Removing the system board

1. system board holder 2. system board

3. release pin

Related Links

Safety instructions

Before working inside your system

Removing the cooling shroud

Removing memory modules

Removing a cooling fan

Removing an AC power supply unit

Removing a DC power supply unit

Removing expansion card risers

Removing an expansion card

176

Removing a heat sink

Removing a processor

Removing the integrated storage controller card

Removing the network daughter card

Removing the optional internal dual SD module

Replacing the optional internal USB memory key

Removing a hot swappable hard drive or SSD

Removing the hard drive backplane

Installing the system board

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Unpack the new system board assembly.

CAUTION: Do not lift the system board by holding a memory module, processor, or other

components.

CAUTION: Do not to damage the system identification button while placing the system board

into the chassis.

2. Hold the touch points and lower the system board into the chassis.

3. Push the system board toward the back of the chassis until the board is seated correctly.

177

Figure 98. Installing the system board

1. system board holder 2. system board

3. release pin

Next steps

1. Install the Trusted Platform Module (TPM). For information about how to install TPM, see the

Installing the Trusted Platform Module section.

2. Replace the following:

a. Cable retention bracket

b. PCIe card holder

c. Integrated storage controller card

d. Internal USB key (if installed)

178

e. Internal dual SD module

f. All expansion card risers

g. Heat sinks or heat sink blanks and processors or processor blanks

h. Memory modules and memory module blanks

i. Network daughter card

j. Cooling fan assembly

k. Cooling shroud

l. Power supply units

3. Reconnect all cables to the system board.

NOTE: Ensure that the cables inside the system are routed along the chassis wall and secured

by using the cable securing bracket.

4. Follow the procedure listed in the After working inside your system section.

5. Import your new or existing iDRAC Enterprise license. For more information, see the Integrated Dell

Remote Access Controller User's Guide at Dell.com/idracmanuals.

6. Ensure that you:

a. Use the Easy Restore feature to restore the Service Tag. For more information, see the

Restoring the Service Tag by using the Easy Restore feature section.

b. If the Service Tag is not backed up in the backup flash device, enter the system service tag

manually. For more information, see the Entering the system service tag section.

c. Update the BIOS and iDRAC versions.

d. Re-enable the Trusted Platform Module (TPM). For more information, see the Re-enabling the

TPM for BitLocker users or Re-enabling the TPM for Intel TXT users section.

Related Links

Replacing the optional internal USB memory key

Installing the optional internal dual SD module

Installing expansion card risers

Installing a processor

Installing a heat sink

Installing memory modules

Installing the network daughter card

Installing the cooling shroud

Installing an AC power supply unit

Installing a DC power supply unit

After working inside your system

Removing the system board

Entering the system Service Tag by using System Setup

If Easy Restore fails to restore the Service Tag, use System Setup to enter the Service Tag.

1. Turn on the system.

2. Press F2 to enter System Setup.

3. Click Service Tag Settings.

4. Enter the Service Tag.

NOTE: You can enter the Service Tag only when the Service Tag field is empty. Ensure that you

enter the correct Service Tag. After the Service Tag is entered, it cannot be updated or changed.

179

5. Click Ok.

6. Import your new or existing iDRAC Enterprise license.

For more information, see the Integrated Dell Remote Access Controller User's Guide at Dell.com/

idracmanuals.

Restoring the Service Tag by using the Easy Restore feature

The Easy Restore feature enables you to restore your system’s Service Tag, license, UEFI configuration,

and the system configuration data after replacing the system board. All data is automatically backed up in

a backup flash device. If BIOS detects a new system board and the Service Tag in the backup flash device,

BIOS prompts the user to restore the backup information.

1. Turn on the system.

If BIOS detects a new system board, and if the Service Tag is present in the backup flash device, BIOS

displays the Service Tag, the status of the license, and the UEFI Diagnostics version.

2. Perform one of the following steps:

• Press Y to restore the Service Tag, license, and diagnostics information.

• Press N to navigate to the Dell Lifecycle Controller based restore options.

• Press F10 to restore data from a previously created Hardware Server Profile.

After the restore process is complete, BIOS prompts to restore the system configuration data.

3. Perform one of the following steps:

• Press Y to restore the system configuration data.

• Press N to use the default configuration settings.

After the restore process is complete, the system restarts.

Trusted Platform Module

Trusted Platform Module (TPM) is a dedicated microprocessor designed to secure hardware by

integrating cryptographic keys into devices. A software can use a Trusted Platform Module to

authenticate hardware devices. As each TPM chip has a unique and secret RSA key burned in as it is

produced, it can perform the platform authentication.

CAUTION: Do not attempt to remove the Trusted Platform Module (TPM) from the system board.

After the TPM is installed, it is cryptographically bound to that specific system board. Any attempt

to remove an installed TPM breaks the cryptographic binding, and it cannot be re-installed or

installed on another system board.

Installing the Trusted Platform Module

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

1. Follow the safety guidelines listed in the Safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

180

Steps

1. Locate the Trusted Platform Module (TPM) connector on the system board.

NOTE: To locate the TPM connector on the system board, see the System board connectors

section.

2. Align the edge connectors on the TPM with the slot on the TPM connector.

3. Insert the TPM into the TPM connector such that the plastic bolt aligns with the slot on the system

board.

4. Press the plastic bolt until the bolt snaps into place.

Figure 99. Installing the TPM

1. TPM 2. TPM connector

3. slot on the TPM connector 4. plastic bolt

5. slot on the system board

Next steps

1. Install the system board.

2. Follow the procedure listed in the After working inside your system section.

Related Links

Safety instructions

System board jumpers and connectors

Before working inside your system

Installing the system board

Initializing the TPM for BitLocker users

Initialize the TPM.

For more information about initializing the TPM, see http://technet.microsoft.com/en-us/library/

cc753140.aspx.

181

The TPM Status changes to Enabled, Activated.

Initializing the TPM for TXT users

1. While booting your system, press F2 to enter System Setup.

2. On the System Setup Main Menu screen, click System BIOS → System Security Settings.

3. From the TPM Security option, select On with Pre-boot Measurements.

4. From the TPM Command option, select Activate.

5. Save the settings.

6. Restart your system.

7. Enter System Setup again.

8. On the System Setup Main Menu screen, click System BIOS → System Security Settings.

9. From the Intel TXT option, select On.

182

Using system diagnostics

If you experience a problem with your system, run the system diagnostics before contacting Dell for

technical assistance. The purpose of running system diagnostics is to test your system hardware without

requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service

and support personnel can use the diagnostics results to help you solve the problem.

Dell Embedded System Diagnostics

NOTE: The Dell Embedded System Diagnostics is also known as Enhanced Pre-boot System

Assessment (ePSA) diagnostics.

The Embedded System Diagnostics provides a set of options for particular device groups or devices

allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

Running the Embedded System Diagnostics from Boot Manager

Prerequisites

Run the Embedded System Diagnostics (ePSA) if your system does not boot.

Steps

1. When the system is booting, press F11.

2. Use the up arrow and down arrow keys to select System Utilities → Launch Diagnostics.

The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the

system. The diagnostics starts executing the tests on all the detected devices.

Running the Embedded System Diagnostics from the Dell Lifecycle

Controller

1. As the system boots, press F11.

2. Select Hardware Diagnostics → Run Hardware Diagnostics.

The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the

system. The diagnostics starts executing the tests on all the detected devices.

183

System diagnostics controls

Menu Description

Configuration Displays the configuration and status of all detected devices.

Results Displays the results of all tests that are executed.

System health Provides the current overview of the system performance.

Event log Displays a time-stamped log of the results of all tests run on the system. This is

displayed if at least one event description is recorded.

184

Jumpers and connectors

This topic provides specific information about the system jumpers. It also provides some basic

information about jumpers and switches and describes the connectors on the various boards in the

system. Jumpers on the system board help to disable system and setup passwords. You must know the

connectors on the system board to install components and cables correctly.

System board jumper settings

For information about resetting the password jumper to disable a password, see the Disabling a forgotten

password section.

Table 45. System board jumper settings

Jumper Setting Description

PWRD_EN

(default)

The password feature is enabled (pins 4–6).

The password feature is disabled (pins 2–4). iDRAC

local access is unlocked at the next AC power

cycle.

NVRAM_CLR

(default)

The configuration settings are retained at system

boot (pins 1–3).

The configuration settings are cleared at the next

system boot (pins 3–5).

Related Links

Disabling a forgotten password

185

System board jumpers and connectors

Figure 100. System board jumpers and connectors

Table 46. System board jumpers and connectors

Item Connector Description

1. J_BP_SIG1 Backplane signal connector 1

2. J_PS2 PSU 2 power connector

3. J_BP_SIG0 Backplane signal connector 0

4 J_SATA_CD Optical drive SATA connector

5. J_SATA_TBU SATA tape backup unit connector

6. J_BP0 Backplane power connector

7. J_TBU Tape backup unit power connector

8 J_PS1 PSU 2 power connector

9. J_IDSDM Internal dual SD module connector

186

Item Connector Description

10. J_NDC Network daughter card connector

11 J_USB USB port

12 J_VIDEO_REAR Video connector

13 J_COM1 Serial connector

14 J_IDRAC_RJ45 iDRAC7 connector

15 J_CYC System identification connector

16 CYC_ID System identification button

17 J_RISER_2AX Riser 2 connector

18 J_RISER_1AX Riser 1 connector

19 J_RISER_2BX Riser 2 connector

20 J_RISER_1BX Riser 1 connector

21 J_RISER_3AX Riser 3 connector

22 J_SATA_B SATA connector

23 J_QS Quick Sync connector

24 J_RISER_3BX Riser 3 connector

25 J_USB_INT Internal USB port

26 J_STORAGE Storage controller card connector

27 J_SATA_A SATA connector

28 BAT Battery connector

29 CPU2 Processor socket 2

30 J_FAN1U_7 Cooling fan connector

31 B1, B5, B9, B2, B6, B10 Memory module sockets

32 J_BP3 Hard drive backplane power connector

33 J_FAN1U_6 Cooling fan connector

34 J_BP_SIG2 Backplane signal connector 2

35 J_FAN1U_5 Cooling fan connector

36 J_BATT_SIG Battery signal connector

37 J_FAN1U_4 Cooling fan connector

38 A1, A5, A9, A2, A6, A10, B3, B7, B11, B4, B8,

B12

Memory module sockets

39 J_FAN1U_3 Cooling fan connector

40 J_FAN2U Cooling fan connector

41 J_FAN1U_2 Cooling fan connector

187

Item Connector Description

42 A12, A8, A4, A7, A11, A3 Memory module sockets

43 J_FAN1U_1 Cooling fan connector

44 J_CTRL_PNL Control panel connector

45 CPU1 Processor socket 1

46 J_FP_USB Front panel USB port

Disabling a forgotten password

The system's software security features include a system password and a setup password. The password

jumper enables the password features or disables them and clears any passwords currently in use.

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Turn off the system, including any attached peripherals, and disconnect the system from the

electrical outlet.

2. Open the system.

3. Move the jumper on the system board jumper from pins 4 and 6 to pins 2 and 4.

4. Close the system.

The existing passwords are not disabled (erased) until the system boots with the jumper on pins 2

and 4. However, before you assign a new system and/or setup password, move the jumper back to

pins 4 and 6.

NOTE: If you assign a new system and/or setup password with the jumper on pins 2 and 4, the

system disables the new passwords the next time it boots.

5. Reconnect the system to its electrical outlet and turn on the system, including any attached

peripherals.

6. Turn off the system, including any attached peripherals, and disconnect the system from the

electrical outlet.

7. Open the system.

8. Move the jumper on the system board jumper from pins 2 and 4 to pins 4 and 6.

9. Close the system.

10. Reconnect the system to its electrical outlet and turn on the system, including any attached

peripherals.

11. Assign a new system and/or setup password.

188

Troubleshooting your system

Safety first — for you and your system

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: Solution validation was performed by using the factory shipped hardware configuration.

Troubleshooting system startup failure

If you boot the system to the BIOS boot mode after installing an operating system from the UEFI Boot

Manager, the system stops responding. To avoid this issue, you must boot to the same boot mode in

which you installed the operating system.

For all other startup issues, note the system messages that appear on the screen.

Troubleshooting external connections

Before troubleshooting any external devices, ensure that all external cables are securely attached to the

external connectors on your system before troubleshooting any external devices.

Troubleshooting the video subsystem

Prerequisites

NOTE: Ensure the Local Server Video Enabled option is selected in the iDRAC Graphical User

Interface (GUI), under Virtual Console. If this option is not selected, local video is disabled.

Steps

1. Check the cable connections (power and display) to the monitor.

2. Check the video interface cabling from the system to the monitor.

3. Run the appropriate diagnostic test.

If the tests run successfully, the problem is not related to video hardware.

Next steps

If the tests fail, see the Getting help section.

Related Links

189

Getting help

Troubleshooting a USB device

Prerequisites

NOTE: Follow steps 1 to 6 to troubleshoot a USB keyboard or mouse. For other USB devices, go to

step 7.

Steps

1. Disconnect the keyboard and/or mouse cables from the system and reconnect them.

2. If the problem persists, connect the keyboard and/or mouse to another USB port on the system.

3. If the problem is resolved, restart the system, enter System Setup, and check if the non-functioning

USB ports are enabled.

NOTE: Older operating systems may not support USB 3.0.

4. Check if USB 3.0 is enabled in System Setup. If enabled, disable it and see if the issue is resolved.

5. In iDRAC Settings Utility, ensure that USB Management Port Mode is configured as Automatic or

Standard OS Use.

6. If the problem is not resolved, replace the keyboard and/or mouse with a known working keyboard

or mouse.

If the problem is not resolved, proceed to step 7 to troubleshoot other USB devices attached to the

system.

7. Turn off all attached USB devices, and disconnect them from the system.

8. Restart the system.

9. If your keyboard is functioning, enter System Setup, verify that all USB ports are enabled on the

Integrated Devices screen. If your keyboard is not functioning, use remote access to enable or

disable the USB options.

10. Check if USB 3.0 is enabled in System Setup. If it is enabled, disable it and restart your system.

11. If the system is not accessible, reset the NVRAM_CLR jumper inside your system and restore the

BIOS to the default settings. See the System board jumper setting section

12. In the IDRAC Settings Utility, ensure that USB Management Port Mode is configured as Automatic

or Standard OS Use.

13. Reconnect and turn on each USB device one at a time.

14. If a USB device causes the same problem, turn off the device, replace the USB cable with a known

good cable, and turn on the device.

Next steps

If all troubleshooting fails, see the Getting help section.

Related Links

Getting help

System board jumper settings

System Setup

190

Troubleshooting iDRAC Direct (USB XML configuration)

For information about USB storage device and server configuration, see the Integrated Dell Remote

Access Controller User's Guide at Dell.com/idracmanuals.

Steps

1. Ensure that your USB storage device is connected to the front USB Management Port, identified by

icon.

2. Ensure that your USB storage device is configured with an NTFS or an FAT32 file system with only

one partition.

3. Verify that the USB storage device is configured correctly. For more information about configuring

the USB storage device, see the Integrated Dell Remote Access Controller User's Guide at Dell.com/

idracmanuals.

4. In the iDRAC Settings Utility, ensure that USB Management Port Mode is configured as Automatic

or iDRAC Direct Only.

5. Ensure that the iDRAC Managed: USB XML Configuration option is either Enabled or Enabled only

when the server has default credential settings.

6. Remove and reinsert the USB storage device.

7. If import operation does not work, try with a different USB storage device.

Next steps

If all troubleshooting fails, see the Getting help section.

Related Links

Getting help

Troubleshooting iDRAC Direct (Laptop connection)

For information about USB laptop connection and server configuration, see the Integrated Dell Remote

Access Controller User's Guide at Dell.com/idracmanuals.

Steps

1. Ensure that your laptop is connected to the front USB Management Port, identified by icon with

a USB Type A/A cable.

2. On the iDRAC Settings Utility screen, ensure that USB Management Port Mode is configured as

Automatic or iDRAC Direct Only.

3. If the laptop is running Windows operating system, ensure that the iDRAC Virtual USB NIC device

driver is installed.

4. If the driver is installed, ensure that you are not connected to any network through WiFi or cabled

ethernet, as iDRAC Direct uses a non-routable address.

Next steps

If all troubleshooting fails, see the Getting help section.

Related Links

Getting help

191

Troubleshooting a serial I/O device

Steps

1. Turn off the system and any peripheral devices connected to the serial port.

2. Swap the serial interface cable with a known working cable, and turn on the system and the serial

device.

If the problem is resolved, replace the interface cable with a known working cable.

3. Turn off the system and the serial device, and swap the serial device with a compatible device.

4. Turn on the system and the serial device.

Next steps

If the problem persists, see the Getting help section.

Related Links

Getting help

Troubleshooting a NIC

Steps

1. Run the appropriate diagnostic test. For more information, see the Using system diagnostics section

for the available diagnostic tests.

2. Restart the system and check for any system messages pertaining to the NIC controller.

3. Check the appropriate indicator on the NIC connector:

• If the link indicator does not glow, the cable connected might be disengaged.

• If the activity indicator does not glow, the network driver files might be damaged or missing.

Install or replace the drivers as necessary. For more information, see the NIC documentation.

• If the problem persists, use another connector on the switch or hub.

4. Ensure that the appropriate drivers are installed and the protocols are bound. For more information,

see the NIC documentation.

5. Enter System Setup and confirm that the NIC ports are enabled on the Integrated Devices screen.

6. Ensure that all the NICs, hubs, and switches on the network are set to the same data transmission

speed and duplex. For more information, see the documentation for each network device.

7. Ensure that all network cables are of the proper type and do not exceed the maximum length.

Next steps

If the problem persists, see the Getting help section.

Related Links

Getting help

Using system diagnostics

192

Troubleshooting a wet system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

2. Remove the system cover.

3. Remove the following components (if installed) from the system:

• power supply unit(s)

• optical drive

• hard drives

• hard drive backplane

• USB memory key

• hard drive tray

• cooling shroud

• expansion card risers (if installed)

• expansion cards

• cooling fan assembly (if installed)

• cooling fans

• memory modules

• processor(s) and heat sink(s)

• system board

4. Let the system dry thoroughly for at least 24 hours.

5. Reinstall the components you removed in step 3 except the expansion cards.

6. Install the system cover.

7. Turn on the system and attached peripherals.

If the problem persists, see the Getting help section.

8. If the system starts properly, shut down the system, and reinstall all the expansion cards that you

removed.

9. Run the appropriate diagnostic test. For more information, see the Using system diagnostics section.

Next steps

If the tests fail, see the Getting help section.

Related Links

Getting help

Using system diagnostics

Removing the system cover

Installing the system cover

Removing the hard drive backplane

Replacing the optional internal USB memory key

193

Removing the cooling shroud

Removing memory modules

Removing a cooling fan

Removing an AC power supply unit

Removing a DC power supply unit

Removing expansion card risers

Removing an expansion card

Removing a heat sink

Removing a processor

Replacing the optional internal USB memory key

Removing a hot swappable hard drive or SSD

Removing the hard drive backplane

Troubleshooting a damaged system

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

2. Remove the system cover.

3. Ensure that the following components are properly installed:

• cooling shroud

• expansion card risers (if installed)

• expansion cards

• power supply unit(s)

• cooling fan assembly (if installed)

• cooling fans

• processor(s) and heat sink(s)

• memory modules

• hard drive carriers/cage

• hard drive backplane

4. Ensure that all cables are properly connected.

5. Install the system cover.

6. Run the appropriate diagnostic test. For more information, see the Using system diagnostics section.

Next steps

If the problem persists, see the Getting help section.

Related Links

Getting help

Using system diagnostics

Removing the system cover

Installing the system cover

194

Installing expansion card risers

Installing a processor

Installing a heat sink

Installing memory modules

Installing the cooling shroud

Installing an AC power supply unit

Installing a DC power supply unit

Installing an expansion card

Troubleshooting the system battery

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: If the system is turned off for long periods of time (for weeks or months), the NVRAM may

lose its system configuration information. This situation is caused by a defective battery.

NOTE: Some software may cause the system time to speed up or slow down. If the system seems

to operate normally except for the time set in System Setup, the problem may be caused by a

software, rather than by a defective battery.

Steps

1. Re-enter the time and date in System Setup.

2. Turn off the system, and disconnect it from the electrical outlet for at least an hour.

3. Reconnect the system to the electrical outlet, and turn on the system.

4. Enter System Setup.

If the date and time displayed in System Setup are not correct, check the System Error Log (SEL) for

system battery messages.

Next steps

If the problem persists, see the Getting help section.

Related Links

Getting help

System Setup

Troubleshooting power supply units

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

195

Troubleshooting power source problems

1. Press the power button to ensure that your system is turned on. If the power indicator does not glow

when the power button is pressed, press the power button firmly.

2. Plug in another working power supply unit to ensure that the system board is not faulty.

3. Ensure that no loose connections exist.

For example, loose power cables.

4. Ensure that the power source meets applicable standards.

5. Ensure that there are no short circuits.

6. Have a qualified electrician check the line voltage to ensure that it meets the needed specifications.

Power supply unit problems

1. Ensure that no loose connections exist.

For example, loose power cables.

2. Ensure that the power supply handle or LED indicates that the power supply is working properly.

For more information about power supply indicators, see the Power indicator codes section.

3. If you have recently upgraded your system, ensure that the power supply unit (PSU) has enough

power to support the new system.

4. If you have a redundant power supply configuration, ensure that both the PSUs are of the same type

and wattage.

You may have to upgrade to a higher wattage PSU.

5. Ensure that you use only PSUs with the Extended Power Performance (EPP) label on the back.

6. Reseat the PSU.

NOTE: After installing a PSU, allow several seconds for the system to recognize the PSU and

determine if it is working properly.

If the problem persists, see the Getting help section.

Related Links

Getting help

Power supply unit indicator codes

Troubleshooting cooling problems

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Ensure that the following conditions exist:

• System cover, cooling shroud, EMI filler panel, memory module blank, or back filler bracket is not

removed.

• Ambient temperature is not higher than the system specific ambient temperature.

• External airflow is not obstructed.

• A cooling fan is not removed or has not failed.

196

• The expansion card installation guidelines have been followed.

Additional cooling can be added by one of the following methods:

From the iDRAC web GUI:

1. Click Hardware → Fans → Setup.

2. From the Fan Speed Offset drop-down list, select the cooling level required or set the minimum fan

speed to a custom value.

From F2 System Setup:

1. Select iDRAC Settings → Thermal, and set a higher fan speed from the fan speed offset or minimum

fan speed.

From RACADM commands:

1. Run the command racadm help system.thermalsettings

For more information, see the Integrated Dell Remote Access User’s Guide at Dell.com/idracmanuals.

Troubleshooting cooling fans

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: The fan number is referenced by the systems management software. In the event of a

problem with a particular fan, you can easily identify and replace it by noting down the fan numbers

on the cooling fan assembly.

1. Follow the safety guidelines listed in safety instructions section.

2. Follow the procedure listed in the Before working inside your system section.

Steps

1. Remove the system cover.

2. Reseat the fan or the fan's power cable.

3. Install the system cover.

4. Restart the system.

Next steps

If the problem persists, see the Getting help section.

Related Links

Safety instructions

Getting help

Before working inside your system

Removing the system cover

Installing the system cover

Installing a cooling fan

197

Troubleshooting system memory

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. If the system is operational, run the appropriate system diagnostic test. See the Using system

diagnostics section for the available diagnostic tests.

If the diagnostic tests indicate a fault, follow the corrective actions provided by the diagnostic tests.

2. If the system is not operational, turn off the system and attached peripherals, and unplug the system

from the power source. Wait at least for 10 seconds, and then reconnect the system to the power

source.

3. Turn on the system and attached peripherals, and note the messages on the screen.

If an error message is displayed indicating a fault with a specific memory module, go to step 12.

4. Enter System Setup, and check the system memory setting. Make any changes to the memory

settings, if needed.

If the memory settings match the installed memory but the problem still persists, go to step 12.

5. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

6. Remove the system cover.

7. Check the memory channels and ensure that they are populated correctly.

NOTE: See the system event log or system messages for the location of the failed memory

module. Reinstall the memory device.

8. Reseat the memory modules in their sockets.

9. Install the system cover.

10. Enter System Setup and check the system memory setting.

If the problem is not resolved, proceed with step 11.

11. Remove the system cover.

12. If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace

the module with a known working memory module.

13. To troubleshoot an unspecified faulty memory module, replace the memory module in the first

DIMM socket with a module of the same type and capacity.

If an error message is displayed on the screen, this may indicate a problem with the installed DIMM

type(s), incorrect DIMM installation, or defective DIMM(s). Follow the on-screen instructions to

resolve the problem.

14. Install the system cover.

15. As the system boots, observe any error message that is displayed and the diagnostic indicators on the

front of the system.

16. If the memory problem persists, repeat step 12 through step 15 for each memory module installed.

Next steps

If the problem persists, see the Getting help section.

Related Links

198

Getting help

Using system diagnostics

Removing the system cover

Installing the system cover

Removing memory modules

Installing memory modules

Troubleshooting an internal USB key

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Enter System Setup and ensure that the USB key port is enabled on the Integrated Devices screen.

2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3. Remove the system cover.

4. Locate the USB key and reseat it.

5. Install the system cover.

6. Turn on the system and attached peripherals, and check if the USB key is functioning.

7. If the problem is not resolved, repeat step 2 and step 3.

8. Insert a known working USB key.

9. Install the system cover.

Next steps

If the problem persists, see the Getting help section.

Related Links

Getting help

System board jumpers and connectors

System Setup

Removing the system cover

Installing the system cover

Replacing the optional internal USB memory key

Troubleshooting an SD card

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: Certain SD cards have a physical write-protect switch on the card. If the write-protect switch

is turned on, the SD card is not writable.

199

Steps

1. Enter System Setup, and ensure that the Internal SD Card Port is enabled.

2. Turn off the system, including any attached peripherals, and disconnect the system from the

electrical outlet.

3. Remove the system cover.

NOTE: When an SD card failure occurs, the internal dual SD module controller notifies the

system. On the next restart, the system displays a message indicating the failure. If redundancy

is enabled at the time of SD card failure, a critical alert will be logged and chassis health will

degrade.

4. Replace the failed SD card with a new SD card.

5. Install the system cover.

6. Reconnect the system to its electrical outlet and turn on the system, including any attached

peripherals.

7. Enter System Setup, and ensure that the Internal SD Card Port and Internal SD Card Redundancy

modes are set to the needed modes.

Verify that the correct SD slot is set as Primary SD Card.

8. Check if the SD card is functioning properly.

9. If the Internal SD Card Redundancy option is set to Enabled at the time of the SD card failure, the

system prompts you to perform a rebuild.

NOTE: The rebuild is always sourced from the primary SD card to the secondary SD card.

Related Links

System Setup

Removing the system cover

Installing the system cover

Troubleshooting an optical drive

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Try using a different CD or DVD.

2. If the problem is not resolved, enter System Setup and ensure that the integrated SATA controller and

the drive's SATA port are enabled.

3. Run the appropriate diagnostic test.

4. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

5. If installed, remove the bezel.

6. Remove the system cover.

7. Ensure that the interface cable is securely connected to the optical drive and to the controller.

8. Ensure that a power cable is properly connected to the drive.

9. Install the system cover.

200

Next steps

If the problem persists, see the Getting help section.

Related Links

Getting help

System Setup

Removing the system cover

Installing the system cover

Removing the optional front bezel

Installing the optional front bezel

Troubleshooting a tape backup unit

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Use a different tape cartridge.

2. Ensure that the device drivers for the tape backup unit are installed and are configured correctly. See

your tape drive documentation for more information about device drivers.

3. Reinstall the tape-backup software as instructed in the tape-backup software documentation.

4. Ensure that the interface cable of the tape drive is connected to the external port on the controller

card.

5. Perform the following steps to ensure that the controller card is properly installed:

a. Turn off the system and attached peripherals, and disconnect the system from the electrical

outlet.

b. Remove the system cover.

c. Reseat the controller card in the expansion card slot.

d. Install the system cover.

e. Turn on the system and attached peripherals.

6. Run the appropriate diagnostic test. For more information, see the Using system diagnostics.

Next steps

If you cannot resolve the problem, see the Getting help section.

Related Links

Getting help

Using system diagnostics

Removing the system cover

Installing the system cover

201

Troubleshooting a hard drive

Prerequisites

CAUTION: This troubleshooting procedure can erase data stored on the hard drive. Before you

proceed, back up all files on the hard drive.

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Run the appropriate diagnostic test. See the Using system diagnostics section.

Depending on the results of the diagnostics test, proceed as needed through the following steps.

2. If your system has a RAID controller and your hard drives are configured in a RAID array, perform the

following steps:

a. Restart the system and press F10 during system startup to run the Dell Lifecycle Controller, and

then run the Hardware Configuration wizard to check the RAID configuration.

See the Dell Lifecycle Controller documentation or online help for information about RAID

configuration.

b. Ensure that the hard drives are configured correctly for the RAID array.

c. Take the hard drive offline and reseat the drive.

d. Exit the configuration utility and allow the system to boot to the operating system.

3. Ensure that the needed device drivers for your controller card are installed and are configured

correctly. See the operating system documentation for more information.

4. Restart the system and enter the System Setup.

5. Verify that the controller is enabled and the drives are displayed in the System Setup.

Next steps

If the problem persists, see the Getting help section.

Related Links

Getting help

Using system diagnostics

System Setup

Troubleshooting a storage controller

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: When troubleshooting a SAS or PERC controller, see the documentation for your operating

system and the controller.

1. Run the appropriate diagnostic test. See the Using system diagnostics section.

202

2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3. Remove the system cover.

4. Verify that the installed expansion cards are compliant with the expansion card installation

guidelines.

5. Ensure that each expansion card is firmly seated in its connector.

6. Install the system cover.

7. Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

8. If the problem is not resolved, turn off the system and attached peripherals, and disconnect the

system from the electrical outlet.

9. Remove the system cover.

10. Remove all expansion cards installed in the system.

11. Install the system cover.

12. Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

13. Run the appropriate diagnostic test. See the Using system diagnostics section. If the tests fail, see the

Getting help section.

14. For each expansion card you removed in step 10, perform the following steps:

a. Turn off the system and attached peripherals, and disconnect the system from the electrical

outlet.

b. Remove the system cover.

c. Reinstall one of the expansion cards.

d. Install the system cover.

e. Run the appropriate diagnostic test. See the Using system diagnostics section.

If the problem persists, see the Getting help section.

Related Links

Getting help

Using system diagnostics

Removing the system cover

Installing the system cover

Removing an expansion card

Installing an expansion card

Troubleshooting expansion cards

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

NOTE: When troubleshooting an expansion card, you also have to see the documentation for your

operating system and the expansion card.

Steps

1. Run the appropriate diagnostic test. See the Using system diagnostics section.

2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

203

3. Remove the system cover.

4. Ensure that each expansion card is firmly seated in its connector.

5. Install the system cover.

6. Turn on the system and attached peripherals.

7. If the problem is not resolved, turn off the system and attached peripherals, and disconnect the

system from the electrical outlet.

8. Remove the system cover.

9. Remove all expansion cards installed in the system.

10. Install the system cover.

11. Run the appropriate diagnostic test. See the Using system diagnostics section.

If the tests fail, see the Getting help section.

12. For each expansion card you removed in step 8, perform the following steps:

a. Turn off the system and attached peripherals, and disconnect the system from the electrical

outlet.

b. Remove the system cover.

c. Reinstall one of the expansion cards.

d. Install the system cover.

e. Run the appropriate diagnostic test. See the Using system diagnostics section.

Next steps

If the problem persists, see the Getting help section.

Related Links

Getting help

Using system diagnostics

Removing the system cover

Installing the system cover

Removing an expansion card

Installing an expansion card

Troubleshooting processors

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that are shipped with your product.

Steps

1. Run the appropriate diagnostics test. See the Using system diagnostics section.

2. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3. Remove the system cover.

4. Ensure that the processor and heat sink are properly installed.

5. Install the system cover.

6. Run the appropriate diagnostic test. See the Using system diagnostics section.

7. If the problem persists, see the Getting help section.

204

Related Links

Getting help

Using system diagnostics

Removing the system cover

Installing the system cover

205

Getting help

Contacting Dell

Dell provides several online and telephone-based support and service options. If you do not have an

active internet connection, you can find contact information on your purchase invoice, packing slip, bill,

or Dell product catalog. Availability varies by country and product, and some services may not be

available in your area. To contact Dell for sales, technical assistance, or customer-service issues:

1. Go to Dell.com/support.

2. Select your country from the drop-down menu on the bottom right corner of the page.

3. For customized support:

a. Enter your system Service Tag in the Enter your Service Tag field.

b. Click Submit.

The support page that lists the various support categories is displayed.

4. For general support:

a. Select your product category.

b. Select your product segment.

c. Select your product.

The support page that lists the various support categories is displayed.

5. For contact details of Dell Global Technical Support:

a. Click Global Technical Support.

b. The Technical Support page is displayed with details to call, chat, or e-mail the Dell Global

Technical Support team.

Documentation feedback

You can rate the documentation or write your feedback on any of our Dell documentation pages and

click Send Feedback to send your feedback.

Accessing system information by using QRL

You can use the Quick Resource Locator (QRL) to get immediate access to the information about your

system.

Prerequisites

Ensure that your smartphone or tablet has the QR code scanner installed.

The QRL includes the following information about your system:

About this task

• How-to videos

206

• Reference materials, including the Owner’s Manual, LCD diagnostics, and mechanical overview

• Your system service tag to quickly access your specific hardware configuration and warranty

information

• A direct link to Dell to contact technical assistance and sales teams

Steps

1. Go to Dell.com/QRL and navigate to your specific product or

2. Use your smartphone or tablet to scan the model-specific Quick Resource (QR) code on your Dell

PowerEdge system or in the Quick Resource Locator section.

Quick Resource Locator for R630

207

Table of Contents

DELL R630 User Manual

Related Manuals