Table of Contents
Haier HW80-B14876 User Manual
Displayed below is the user manual for HW80-B14876 by Haier which is a product in the Washing Machines category. This manual has pages.
Related Manuals
EN
User manual
Washing machine
HW80-B14876
HW100-B14876
Thank You EN
2
Legend
Warning – Important Safety information
General information and tips
Environmental information
Disposal
Help protect the environment and human health. Put
the packaging in applicable containers to recycle it.
Help to recycle waste of electrical and electronic ap-
pliances. Do not dispose appliances marked with this
symbol with the household waste. Return the product
to your local recycling facility or contact your municipal
oce.
Thank you for purchasing a Haier Product.
Please read these instructions carefully before using this appliance. The instructions con-
tain important information which will help you get the best out of the appliance and ensure
safe and proper installation, use and maintenance.
Keep this manual in a convenient place so you can always refer to it for the safe and proper
use of the appliance.
If you sell the appliance, give it away, or leave it behind when you move house, make sure
you also pass this manual so that the new owner can become familiar with the appliance
and safety warnings.
WARNING!
Risk of injury or suocation!
Disconnect the appliance from the mains supply. Cut o the mains cable and dispose
of it. Remove the door catch to prevent children and pets to get closed in the appliance.
EN Content
3
1-Safety information ........................................................................................................................... 4
2-Product description ......................................................................................................................... 7
3-Control panel .................................................................................................................................... 8
4-Programmes ...................................................................................................................................12
5-Consumption ..................................................................................................................................13
6-Daily use ...........................................................................................................................................14
7-Eco-friendly washing ....................................................................................................................19
8-Care and cleaning ..........................................................................................................................20
9-Troubleshooting .............................................................................................................................23
10-Installation .....................................................................................................................................26
11-Technical data ...............................................................................................................................30
12-Customer service ........................................................................................................................32
1-Safety information EN
4
Before switching on the appliance for the rst time read the follow-
ing safety hints!:
WARNING!
Before rst use
▶Make sure there is no transport damage.
▶Make sure all transport bolts are removed.
▶Remove all packaging and keep out of children´s reach.
▶Handle the appliance always with at least two persons because it
is heavy.
Daily use
▶This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental ca-
pabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
▶Keep away children under 3 years of age from the appliance un-
less they are constantly supervised.
▶Children shall not play with the appliance.
▶Do not let children or pets come close to the appliance when the
door is open.
▶Store washing agents out of reach of children.
▶Pull up zips, x loose threads and take care for small items to pre-
vent laundry from being entangled. If necessary, use an appropri-
ate bag or net.
▶Do not touch or use the appliance when barefoot or with wet or
damp hands or feet.
▶Do not cover or encase the appliance during operation or after-
wards to allow any moisture or dampness to evaporate.
▶Do not place heavy objects or sources of heat or damp on top of
the appliance.
▶Do not use or store flammable detergent or dry cleaning agent in
close vicinity to the appliance.
▶Do not use any flammable sprays in close vicinity to the appliance.
▶Do not wash any garments treated with solvents in the appliance
without having dried them previously in the air.
EN 1-Safety information
5
WARNING!
Daily use
▶Do not remove or insert the plug in the presence of flammable
gas
▶Do not hot wash foam rubber or sponge-like materials.
▶Do not wash any laundry which is polluted with flour.
▶Do not open detergent drawer during any wash cycle.
▶Do not touch the door during the washing process, it gets hot.
▶Do not open the door if the water level is visibly over the porthole.
▶Do not force the door to open. The door is tted with a self-lock
device and will open shortly after the washing procedure is ended.
▶Switch o the appliance after each wash programme and before
undertaking any routine maintenance and disconnect the appli-
ance from the electrical supply to save electricity and for safety.
▶Hold the plug, not the cable, when unplugging the appliance.
Maintenance / cleaning
▶Make sure children are supervised if they carry out cleaning and
maintenance.
▶Disconnect the appliance from the electrical supply before un-
dertaking any routine maintenance.
▶Keep the lower part of the porthole clean and open door and de-
tergent drawer if appliance is not in use to prevent odours.
▶Do not use water spray or steam to clean the appliance.
▶Replace a damaged supply cord only by the manufacturer, its ser-
vice agent or similarly qualied persons in order to avoid a hazard.
▶Do not try to repair the appliance by yourself. In case of repair
please contact our customer service.
Installation
▶The appliance should be placed in a well-ventilated place. Ensure
a location which allows opening the door fully.
▶Never install the appliance outdoors in a damp place, or in an area
which may be prone to water leaks such as under or near a sink
unit. In the event of a water leak cut power supply and allow the
machine to dry naturally.
1-Safety information EN
6
Intended use
This appliance is intended for washing machine-washable laun-
dry only. Anytime follow the instructions given on the label of each
garment label. It is designed exclusively for domestic use inside the
house. It is not intended for commercial or industrial use.
Changes or modications to the device are not allowed. Unintended
use may cause hazards and loss of of all warranty and liability claims.
WARNING!
Installation
▶Install or use the appliance only where the temperature is above
5 °C.
▶Do not place the appliance directly on a carpet, or close to a wall
or furniture.
▶Do not install the appliance in direct sunlight or in the near of heat
sources(e.g. stoves, heaters).
▶Make sure that the electrical information on the rating plate
agrees with the power supply. If it does not, contact an electri-
cian.
▶Do not use multi-plug adapters and extension cables.
▶Make sure only the delivered electric cable and hose set are used.
▶Make sure not to damage the electric cable and the plug. If dam-
aged have it replaced by an electrician.
▶Use a separate earthed socket for the power supply which is easy
accessible after installation. The appliance must be earthed.
Only for UK: The appliance’s power cable is tted with 3-cord
(grounding) plug that ts a standard 3-cord (grounded) socket.
Never cut o or dismount the third pin (grounding). After the ap-
pliance is installed, the plug should be accessible.
▶Make sure the hose joints and connections are rm and there is
no leakage.
EN 2-Product description
7
2.1 Picture of appliance
Front (Fig. 2-1): Rear side (Fig. 2-2):
2.2 Accessories
Check the accessories and literature in accordance with this list (Fig.:2-3):
Note:
-
2-3
Underwear
Sport
Anti-allergy
Daily Wash
Synthetic
Mix
Baby Care Hygienic
Self Clean
Spin/Drain
Express15 min
Duvet
Delicate
Wool
Temp. SpeedDelay Start/PauseExtra
Rinse
Cotton Cotton+ HW80-B14876
Steam
8kg
I1
R5
R9 R10 R6
R7
R8
1 Detergent /
Softener drawer
2 Work top
3 Display
4 Programme selector
5 Panel
6 Service flap
7 Adjustable feet
8 Door handle
1 Iron bar (I1 - I2)
2 Transportation bolts (T1-T4)
3 Rear wall reinforcement
(HW80:1 pcs;HW100:2 pcs)
4 Power cord
5 Water inlet vave
6 Drain hose
7 Rear wall reinforcement screws
(HW80:4 pcs ,R1-R4;HW100:10 p cs ,R1-R10)
2-1 2-2
Inlet hose-
assembly1) 6 Blanking
plugs
Drain hose
bracket User manual
Warranty
card
1
6
8
7
3 5
1 2 4 5 6 73
42
Noise reduc-
tion pads
2x
2x
3-Control panel EN
8
Underwear
Sport
Anti-allergy
Daily Wash
Synthetic
Mix
Baby Care Hygienic
Self Clean
Spin/Drain
Express15 min
Duvet
Delicate
Wool
Temp. SpeedDelay Start/PauseExtra
Rinse
Cotton Cotton+ HW120-B14876
Steam
3
Note : Acoustic signal
In following cases an acoustic signal sounds:
▶when pressing a button
▶when turning the programme selector
▶at the end of programme
▶in case of failures
The acoustic signal can be deselected if necessary ; see DAILY USE.
1 Detergent / Softener Drawer
2 Display
3 Programme selector
4
5 “Start/Pause“ button
6 Steam
7 Extra rinse
8 Speed
9 Temp.
10
Temp. SpeedDela Sy tart/PauseExtra
Rinse
Steam
3-2
11 Child lock
12 Delay
12 11
89
10
7 6 5
2 31
4
Function buttons
3.1 Detergent drawer
1 Compartment : Bleaching agent for cotton/syn-
thetic programme.
2 Compartment : Liquid detergent for programme
3 Compartment : Softener, Conditioning agent etc.
4 Compartment : Powder detergent for programme
Please refer to the information on detergent package
to obtain recommendation for using detergent in vari-
ous washing temperatures.
3.2 Display
If the appliance is on, display will light up the actual sta-
washing time, spin speed, temperature, etc will appear
(Fig. 3-2).
3-1
EN 3-Control panel
9
Programme status indication Programme cycle indication
Display for washing time, end time
delay as well as error codes and
service information.
Remaining opera-
tion time
Remaining delay
time
Rinse cycle
Wash cycle Spin/drainage cycle
Automatic weighing
Steam
Display symbols:
3.3 Program selector
By turning the knob (Fig. 3-3) one of 16 programmes
can be selected, its default settings will be displayed.
Press this button (Fig. 3-4) gently to switch on, the dis-
play is shining. Press it again for about 2 seconds to
-
vated after a while machine will shut down automatically
3.5 “Start/Pause“ button
Touch this button (Fig. 3-5) gently to start or interrupt
the currently displayed programme.
Underwear
Sport
Anti-allergy
Daily Wash
Synthetic
Mix
Baby Care Hygienic
Self Clean
Spin/Drain
Express15 min
Duvet
Delicate
Wool
Temp. SpeedDelay Start/PauseExtra
Rinse
Cotton Cotton+
HW120-B14876
Steam
3-3
3-4
Start/Pause
3-5
3-Control panel EN
10
3.6 Function buttons
The function buttons (Fig. 3-6) enables additional op-
tions in the selected programme before program start.
The related indicators are displayed.
-
gram, all options are disabled.
If a button has multiple options, the desired option can
be selected by pressing the button sequentially.
To delete the setting or to cancel the setting process,
press the function button until the desired LED lights
Not all functions are available for all programmes (see
PROGRAMMES).
Note: Factory settings
there is no special requirement default settings are recommended.
3.6.1 Function button “Extra Rinse“
Press this button (Fig. 3-6-1) to rinse the laundry more
intense with fresh water. This is recommended for
people with sensitive skin.
By pressing the button several times one to three ad-
ditional cycles (display P1-P3)can be selected.
Different programme has different extra maximum
rinsing times.
3.6.2 Function “Delay”
Press this button (Fig. 3-6-2) to start the program with
a delay. End time delay could be increased in steps of
means end of programme cycle will be in 6 hours and
30 minutes. Touch “Start/Pause” button to activate the
time delay.
The time delay must be longer than the programme run
time. Otherwise the programme will start immediately.
For deactivating the time delay; rotate programme se-
lector.
Note: Liquid detergent
If using liquid detergent, it is not recommended to activate the end time delay.
Temp. SpeedDelay Extra
Rinse
Steam
3-6
Extra
Rinse
3-6-1
Delay
3-6-2
EN 3-Control panel
11
Steam
3.6.3 Function “ “
Press the “ ” button (Fig.3-6-3) can choose dif-
ferent washing time. This function does not apply to
“Delicate”,”Self Clean” and “Spin/Drain” programs.
3.6.4 Function “Steam“
Press this button (Fig.3-6-4), the steam program can
be selected. When this program is selected, the de-
fault temperature is the max temperature of this pro-
gram. You can select if you require this function when
programs “Cotton, Mix, Synthetic, Underwear, Baby Care,
Anti-allergy“ are used .When you select the program
“Steam“ the icon light up to warn you, the icon turns
the program, you can not change the temperature. If
you press the temperature button the program will be
canceled. Switch on the washing machine and select
this program. If the washing machine is working you
cannot select this program.
3.6.5 Function “Speed“
Press this button (Fig. 3-6-5) to change or deselect the
spin of the program If no value is illuminated the laundry
will not spun.
3.6.6 Function “Temp”
Press this button (Fig. 3-6-6) to change the washing
temperature of the programme.
3.6.7 Child lock
This option blocks all panel elements against activation.
After programme start press button “ ” and
”Delay” (Fig. 3-6-7 for 3 seconds simultaneously; child
lock symbol is displayed. For unlocking press again the
two buttons.
Temp.
Speed
3-6-3
3-6-4
3-6-5
3-6-6
Delay
3-6-7
4-Programmes EN
12
Max.
load
in kg
HW100/
HW80
Temperature Preset
Spin
speed
in rpm
Function
Delay
Steam
Extra Rinse
i-time
in °C
Program Fibre typemax Preset
Cotton 10/8 902) 40 •º/•Cotton 1400 ••••
Mix 10/8 60 30 •º/•
Lightly soiled mixed
laundry of cotton and
synthetics.
1000 ••••
Synthetic 10/8 60 40 •º/•Synthetics or mixed
fabric 1200 ••••
Underwear 5/4 60 40 •º/•Cotton/Synthetic 1000 ••••
Baby Care 5/4 902) 40 •º/•Cotton/Synthetic 1000 ••••
Anti -all
ergy
5/4 902) 60 •º/•Cotton/Synthetic 1000 ••••
Daily Wash 5/4 60 30 •º/•Cotton 1000 •/• •
Sport 2.5/2 40 30 •º/•Sports Wear 1000 •/• •
Cotton+ 10/8 902) 30 •º/•Cotton; standard pro-
gram for energy labelling 1000 •/• •
Delicate 1/1 30 30 •º/•Silk 600 •/•/
Duvet 2.5/2 40 40 •º/•Cotton fabrics 800 •/• •
Express
15min3) 1/1 40 * •º/•Cotton/Synthetic 1000 •/• •
Hygienic 5/4 902) 902) •º/•Cotton/Synthetic 1000 •/• •
Wool 1/1 40 * •º/•Wollen fabrics 800 •/• •
Self Clean 0 902) 902) º/ /
/
/- 600 ////
Spin/Drain 10/8 / / / / / All fabrics 1000 ////
1) Relating to dry laundry. *: Water is not heated up.
2) Choose 90 °C wash temperature only for special hygienic requirements.
3) Reduce detergent amount because programme duration is short.
1)
Detergent compartment for:
1
Bleaching agent
2
Liquid detergent
3
Softener, conditioning agent etc.
4
Powder detergent
•
Yes, º
Optional, / No
EN 5-Consumption
13
Programme
Temper-
ature
in °C
HW100/
HW80
Max. load
in kg
HW100/HW80
Energy
in kWh
HW100/HW80
Water
in L
HW100/HW80
Washing time
in h:min
HW100/HW80
Spin drying
performance
HW100/HW80
Cotton+ *
40°C 5/4 0.50/0.46 46/37 4:08/3:27 B
60°C 5/4 0.56/0.56 46/37 4:12/3:30 B
60°C 10/8 0.50/0.54 59.5/53 4:12/3:30 B
* Standard programme for the Energy Labelling according to 2010/30 EU:
Cotton+ 60°C /40°C with max. spin speed setting
The standard 60°C and 40°C cotton programmes are suitable to clean normally soiled
cycle temperature.
Note: Auto Weight
The appliance is equipped with a loading recognition. At low loading, energy, water and
washing time will be reduced automatically in some programs. The display shows Auto.
6-Daily use EN
14
6.3 Preparing laundry
▶Sort out clothes according to fabric (cotton, syn-
thetics, wool or silk) and to how dirty they are (Fig.
6-3). Pay attention to the care labelling of wash-
ing labels.
▶Separate white clothes from coloured ones.
they fade or run.
▶Empty pockets (keys, coins, etc.) and remove
harder decorative objects (e.g. brooches).
▶
into a wash bag to care for this delicate laundry
(hand or dry cleaning would be better).
▶Close zippers, velco fastener and hooks, make
sure the buttons are sewn on tightly.
▶
hem, delicate underwear (Dessous) and small
items such as socks, belts, bras, etc. in a wash
bag.
▶Unfold large pieces of fabric such as bed sheets,
bedspreads etc.
▶Turn jeans and printed, decorated or color-inten-
sive textiles inside out; possibly wash separately.
6.1 Power supply
Connect the washing machine to a power supply
(220V to 240V~/50Hz; Fig. 6-1). Please refer also to
section Installtion.
6.2 Water connection
▶Before connecting check the cleanliness and clar-
ity of the water inlet.
▶Tun on the tap (Fig.6-2).
Note: Tightness
Before use check for leakage in the joints between the tap and the inlet hose by turning on
the tap.
CAUTION!
Non-textile, as well as small, loose or sharp-edged items may cause malfunctions and
damage of clothes and appliance.
6-3
6-1 6-2
EN 6-Daily use
15
Care chart
Washing
Washable up to 95°C
normal process
Washable up to 60°C
normal process
Washable up to 60°C
mild process
Washable up to 40°C
normal process
Washable up to 40°C
mild process
Washable up to 40°C
very mild process
Washable up to 30°C
normal process
Washable up to 30°C
mild process
Washable up to 30°C
very mild process
Wash by hand
max. 40°C
Do not wash
Bleaching
Any bleaching allowed Only oxygen/
non -chlorine
Do not bleach
Drying
Tumble drying possible
normal temperature
Tumble drying possible
lower temperature
Do not tumble dry
Line drying Flat drying
Ironing
Iron at a maximum
temperature
up to 200 °C
Iron at a medial tem-
perature
up to 150°C
Iron at a low temper-
ature up to 110 °C;
without steam (steam
ironing may cause irre-
versible damage)
Do not iron
Professional Textile Care
Dry cleaning in tetra-
chloroethene
Dry cleaning in hy-
drocarbons
Do not dry clean
Professional wet clean Do not professional
wet clean
6.4 Loading the appliance
▶Put in the laundry piece by piece
▶Don‘t overload. Note the dierent maximum load according to programmes! Rule of
thumb for maximum load: Keep six inches between load and drum top.
▶Close the door carefully. Make sure that no pieces of laundry are pinched.
6-Daily use EN
16
6.5 Selecting detergent
▶
▶Use only machine wash approved detergent.
▶
▶ Mind always detergent manufacturer recommendations.
.
▶Do not use dry cleaning agents such as trichloroethylene and similar products.
Choose the best detergent
Programme
Kind of detergent
Universal Colour Delicate Special Softener
Cotton L/P L/P - - o
Mix L/P L/P - - o
Synthetic L/P L/P L - o
Underwear L/P L/P - - o
Baby Care L/P L/P - - o
Anti-allergy - - - L o
Daily Wash L/P L/P L - o
Sport - - - L o
Cotton+ L/P L/P - - o
Delicate - - L - o
Duvet - - L L o
Express 15 min L/P L/P L - o
Hygienic L/P L/P L - o
Wool - - - L o
Self Clean L/P - - L o
Spin/Drain - - - - o
L = gel-/liquid detergent P = powder detergent O = optional _ = no
If using liquid detergent, it is not recommended to activate the time delay.
We recomment by using:
▶Laundry powder: 20°C to 90°C* (best use:: 40-60°C)
▶Color detergent: 20°C to 60°C (best use: 30-60°C)
▶Wool/delicate detergent: 20°C to 30°C (= best use:)
* Choose 90 °C wash temperature only for special hygienic requirements.
EN 6-Daily use
17
6.7 Switch on the appliance
(Fig. 6-7).
6.6 Adding detergent
1. Slide out the detergent drawer.
2. Put the required chemicals into corresponding
compartments (Fig. 6-6),
3. Push back the drawer gently.
Note:
▶Remove detergent residues before next wash cycle from the detergent drawer.
▶Do not overuse detergent or softener.
▶Please follow the instruction on the detergent package.
▶
▶Concentrated liquid detergent should be diluted before adding.
▶Do not use liquid detergent if function “Delay“ is selected.
▶Carefully choose the programme settings according to the care symbols on all laun-
dry labels and according to the programme table.
6.8 Select a programme
To get the best washing results, select a programme
type.
Turn the programme knob (Fig. 6-8) to select the right
programme. The default settings are displayed.
6.9 Add individual selections
Select required options and settings (Fig. 6-9); refer to
Control Panel.
6-7
Note: Odour removal
amount of detergent in washing agent compartment (2) or special machine cleaner to
remove possibly corruptive residues.
6-6
Temp. SpeedDelay Extra
Rinse
Steam
6-9
Underwear
Sport
Anti-allergy
Daily Wash
Synthetic
Mix
Baby Care Hygienic
Self Clean
Spin/Drain
Express15 min
Duvet
Delicate
Wool
Cotton Cotton+
H
6-8
6-Daily use EN
18
6.12 After washing
1. At programme cycle end END is displayed.
2.
3. Remove laundry as soon as possible to go easy on it and to prevent more wrinkling.
4.
5. Unplug the power cord.
6. Open the door to prevent formation of moisture and odours. Let it open while not used.
6.13 Activate or deactivate the buzzer
The acoustic signal can be deselected if necessary:
1. Switch on the appliance.
2. Select the Spin /Drain programme.
3. Press the “i-time “button and “Speed” button at the same time for about 3 seconds.
“bEEP OFF” will be displayed and the buzzer will be deactivated. For activating the buzzer
press these two buttons at the same time again. “bEEP ON” will be displayed.
6.11 Interrupt - cancel wash programme
To interrupt a running programme press gently “Start/Pause“. Press it again to resume
operation.
To cancel a running programme and all its individual settings:
1. Press “Start/Pause” button to interrupt the running programme.
Press this
2.
3. Run programme “Spin” to drain the water.
4. Select a new programme and start it.
Note: Door lock
▶For safety reasons the door is locked partially during the washing cycle. It is only pos-
sible to open the door at the end of the programme or after the programme was can-
celled correctly (see description above).
▶In case of high water level, high water temperature and during spinning it is not pos-
sible to open the door; Lock is displayed.
Note: Standby mode / energy-saving mode
The switched on appliance will go into standby mode if it will not be activated within 2
minutes before starting the programme or at the end of programme. The display switch-
6.10 Start wash programme
Press “Start/Pause“ button (Fig. 6-10) to start; appli-
ance operates according to present settings. Changes
are only possible by cancelling the programme.
Start/Pause
6-10
button gently to switch on.
EN 7-Eco-friendly washing
19
Environmentally responsible use
▶To achieve best use of energy, water, detergent and time you should use the recom-
mended maximum load size.
▶Do not overload (hand width clearance above laundry).
▶For slightly soiled laundry select the Quick Wash programme.
▶Apply exact dosages of each washing agent.
▶Choose the lowest adequate washing temperature - modern detergents are e-
ciently cleaning below 60°C.
▶Raise default settings only due to heavy staining.
▶Select max. spinning speed if a domestic dryer is used.
8-Care and cleaning EN
20
8.1 Cleaning the detergent drawer
Take always care there are no detergent residues.
Clean the drawer regularly (Fig. 8-1):
1. Pull out the drawer until it stops.
2. Press the release button and remove the drawer.
3. Flush the drawer with water until it is clean and
insert the drawer back in the appliance.
8.2 Cleaning the machine
▶Unplug the machine during cleaning and mainte-
nance.
▶Use a soft cloth with soap liquid to clean the ma-
chine case (Fig. 8-2) and rubber components.
▶Do not use organic chemicals or corrosive sol-
vents.
Note: Hygiene
For regular maintenance, we recommend running the program Self Clean within 100
cycles to avoid possible corrosive residues. Add a small amount of detergent to the de-
tergent compartment (2) - or use a special machine cleaner. If you run more than 100
cycles and do not use the Self Clean program, the Self Clean program light flashes
when the machine is in standby mode. It is recommended to run the Self Clean .
To prevent blockage of water supply by solid substanc-
▶
supply.
▶Unscrew the water inlet hose at the back (Fig.
8-3) of the appliance as well as on the tap.
▶
▶
8.4 Cleaning the drum
▶Remove accidentally washed metal parts such as
pins, coins, etc. from the drum (Fig. 8-5) because
they cause rust stains and damage.
▶Use a non-chloride cleaner for removing rust
stains. Observe the warning hints of the cleaning
agent manufacturer.
▶Do not use any hard objects or steel wool for clean-
ing.
8-1
8-5
8-3 8-4
HW70-BP12758
Wool
R
Under-wear
Sport
Anti-allergy
Daily Wash
Baby Care
Self Clean
Spin/Drain
Express
15 min
Duvet
Cotton
Synthetic
Mix
Cotton+
Delicate
Hygienic
capacity
7kg
°C
60
°C
40
Underwear
Sport
Anti-allergy
Daily Wash
Synthetic
Mix
Baby Care Hygienic
Self Clean
Spin/Drain
Express15 min
Duvet
Delicate
Wool
Temp. SpeedDela Sy tart/PauseExtra
Rinse
Cotton Cotton+ HW120-B14876
Steam
8-2
1
2
EN 8-Care and cleaning
21
1. Turn o and unplug the machine (Fig. 8-8).
2. Open service flap at the right corner of appliance
front (Fig. 8-9).
3. Provide a flat container to catch leach water
(Fig. 8-10). There could be bigger amounts!
4. Pull the drainhose out and hold its end above the
container (Fig. 8-10).
5. Take the sealing plug out of the drainhose (Fig.
8-10).
6. After complete drainage close drainhose and
push it back into the machine (Fig. 8-11).
7. Unscrew and remove counter clockwise the pump
lter (Fig. 8-12).
8. Remove contaminants and dirt (Fig. 8-13).
8.5 Long periods of disuse
If the appliance is left idle for a longer period:
1. Pull out the electrical plug (Fig. 8-6).
2. Turn o water supply (Fig. 8-7).
3. Open the door to prevent formation of moisture
and odours. Let door open while not used.
Before next usage check carefully power cord, water
inlet and drain hose. Make sure everything is properly
installed and without leackage.
WARNING!
Scalding Risk! Water in the pump lter can be very
hot! Before any action please ensure water has
cooled down.
Note: Hygiene
After long periods of disuse we recommended to run programme HYGIENIC with no
load and small amount of detergent in washing agent compartment (2) or special ma-
chine cleaner to remove possibly corruptive residues.
8.6 Pump lter
Clean the lter once a month and check the pump lter
for instanvce if the appliance:
▶doesn´t drain the water.
▶doesn´t spin.
▶cause unusual noise while running.
8-6 8-7
8-10 8-11
8-12 8-13
8-8 8-9
8-Care and cleaning EN
22
CAUTION!
▶Pump lter sealing has to be clean and unhurt. If the lid is not full tightened, water
can escape.
▶The lter must be in place, or it may lead to leakage.
9. Clean carefully pump lter, e.g. using running water
(Fig. 8-14).
10. Rex it thoroughly (Fig. 8-15).
11. Close service flap..
8-14 8-15
EN 9-Troubleshooting
23
of a problem please check all shown possibilities and follow below instructions before you
WARNING!
▶Before maintenance, deactivate the appliance and disconnect the mains plug from
the mains socket.
▶
improper repairs can cause considerable consequential damages.
▶A damaged power cable should only be replaced by the manufacturer, its service
9.1 Information codes
Following codes are displayed only for information referring to the washing cycle. No
measures must be performed.
Code Message
1:25
The remaining wash cycle time will be 1 hour and 25 minutes.
6:30
The remaining wash cycle time including chosen end-time delay will be 6 hours and 30 minutes
.
AUtO
Automatic load detection is working; only in some programs.
End
Lock-
Door is closed because of high water level, high water temperature or spinning cycle
.
bEEP OFF The buzzer is deactivated.
bEEP ON The buzzer is activated.
9.2 Troubleshooting with display code
Problem Cause Solution
E1
• Drainage error, water is not fully drained
within 6 minutes.
•
• Check drain hose installation.
E2
• Lock - error. • Shut the door properly.
E4
• Water level not reached after 12 minutes.
• Drain hose is self-syphoning.
• Make sure that tap is fully opened and water
pressure is normal.
• Check drain hose installation.
E8
• Water protective level - error. • Contact the After sales service.
The function keys is closed.The programme changing is invalid.
9-Troubleshooting EN
24
Problem Cause Solution
F3
Temperature sensor - error. Contact the After sales service.
F4
Heating error.
Contact the After sales service.
F7
Motor - error. Contact the After sales service.
FA
Water level sensor error. Contact the After sales service.
FC0, FC1 or
FC2
Abnormal communication error.
Contact the After sales service.
Unb
Unbalanced load - error. Check a .murd eht ni daol yrdnual ecnalab dn
Reduce the load.
9.3 Troubleshooting without display code
Problem Cause Solution
Washing machine
fails to operate.
Programme is not yet started.
Door is not properly closed.
Machine has not been switched on.
Power failure.
Child lock is activated.
Check programme and start it.
Close the door properly.
Switch the machine on.
Check power supply.
Deactivate child lock.
Washing machine
water.
No water.
Inlet hose is kinked.
Water pressure is less than 0.03
MPa.
Door is not properly closed.
Water supply failure.
Check water tap.
Check inlet hose.
Check water pressure.
Close the door properly.
Ensure the water supply.
Machine is draining Height of drain hose is below 80
cm.
Drain hose end could reach into
water.
Make sure that drain hose is
properly installed.
Make sure the drain hose is not
in water.
Drainage failure. Drain hose is blocked.
Drain hose end is higher than 100
cm above floor level.
Unblock drain hose.
Make sure that drain hose is
properly installed.
Strong vibration
while spinning.
Not all transportation bolts have
been removed.
Appliance has no solid position.
Machine load is not correct.
Remove all transportation
bolts.
Ensure solid ground and a ev-
elled position.
Check load weight and balance.
Operation stops
before completing
wash cycle.
Water or electric failure. Check power and water supply.
Operation stops for
a period of time.
Appliance displays error code.
Problem due to load pattern.
Programme performs soaking cycle
Consider display codes.
Reduce or adjust load.
Cancel programme and restart.
Fb
Machine leakage.
Open drain pump to drain,Shut down the machine.
Contact the After sales service.
EN 9-Troubleshooting
25
Problem Cause Solution
Excessive foam
floats drum and/or
detergent drawer.
• Detergent is not a appropriate.
• Excessive use of detergent.
• Check detergent recommen-
dations.
• Reduce amount of detergent.
Automatic adjust-
ment of washing
time.
• Washing programme duration will
be adjusted.
• This is normal and doesn‘t af-
fect functionality.
Spinning fails. • Unbalance of laundry. • Check machine load and laun-
dry and run a spinning pro-
gramme again.
Unsatisfactory
washing result.
• Degree of pollution does not agree
with selected programme
• Detergent quantitiy was not suf-
cient.
• Maximum load has been excee-
ded.
• Laundry was unevenly distribu-
ted in the drum.
• Select an other programme.
• Choose the detergent acc.
to the degree of pollution
and acc. to manufacturer
specications.
• Reduce loading.
• Loose the laundry.
Washing powder
residues are on the
laundry.
• Insoluble particles of detergent can
remain as white spots on the laun-
dry.
• Perform extra rinse.
• Try to brush the points from the
dry laundry.
• Choose an other detergent.
Laundry has grey
patches.
• Caused by fats such as oils, creams
or ointments.
• Pretreat the laundry with a spe-
cial cleaner.
Note: Foam formation
If too much foam is inspected during spin cycle, motor stops and drain pump will be ac-
tivated for 90 seconds. If that elimination of foam fails up to 3 times, programme ends
without spinning.
Should the error messages reappear even after the taken measures, switch o the appli-
ance, disconnect the power supply and contact the customer service.
9.4 In case of power failure
The current programme and its setting will be saved.
When power supply is restored operation will be re-
sumed.
If a power failure cuts an operating wash programme
door opening is mechanically blocked. To get out any
laundry water level should not be seen in the glassy
porthole of the door. - Danger of burns! Water level
has to be lowered as described in “Pump lter“. Not till
then pull lever (A) beneath service flap (Fig. 9-1) until
door is unlocked by a gentle click. Afterwards rex all
parts.
9-1
10-Installation EN
26
10.1 Preparation
▶Take the appliance out of the packaging.
▶
keep them out of childrens reach. While opening the package, water drops may be
seen on plastic bag and porthole. This normal phenomenon results from water tests
in the factory.
10.3 Dismantle the the transportation bolts
The transport protection on the rear side is designed
for clamping anti-vibration components inside the ap-
pliance during transportation to prevent inner damage.
All elements (I, R, S and T, Fig 10-2) must be removed
before use.
1. Remove all 4 bolts (T1 - T4) (Fig. 10-3)
Note: Packaging disposal
Keep all packaging materials out of children´s reach and dispose them in an environmen-
tally friendly manner.
10.2 OPTIONAL: Install noise reduction pads
1.
2.
3.
10.1
10-2
I1
R5
R6
R7 R9 R10
S2
S1
R8
T1
T4
T3
T2
10-3
1.When opening the shrink package,you will find four
noise reduction pads.These are used for reducing
noise.(Fig. 10.1)
2. Lay the washing machine down to its side, port-
hole pointing upwards, bottom side towards op-
3.
Take out the noise reduction pads and remove the
double-sided adhesive protective film；Paste around
the bottom；The noise reduction pads under the
washing machine cabinet as shown in Figure 3.(two
longer pads in position 1 and 3, two shorter pads in
position 2 and 4). Finally set the machine upright again.
EN 10-Installation
27
10.5 Aligning the appliance
Adjust all feet (Fig. 10-7) to achieve a complete level
position. This will minimize vibrations and thus noise
during use. It will also reduce wear and tear. We recom-
mend to use a spirit level for adjustment. Floor should
be as stable and flat as possible.
1. Loose the locknut (1) by using a wrench.
2. Adjust the high by turning the foot (2).
3. Tighten lock ut (1) against the housing.
10.4 Moving the appliance
If the machine is to be moved to a distant location, replace the transportation bolts removed
before installation to prevent damage: The assembly takes place in reverse order.
Note: Keep in safe place
Keep all parts of the transport protection in a safe place for later use. Whenever the ap-
2. Remove the 10 screws (R1 - R10) from lower back
reinforcement. take out reinforcements (S1 and
S2) from the machine.*HW100-B14876
Remove the 4 screws (R1 - R4) from lower back
reinforcement. take out reinforcements (S2)
from the machine.*HW80-B14876
(Fig. 10-4)
3. Pull out the 2 iron bars I1 and I2 (Fig. 10-5)
10-4
S2
R1-R4
S1
R5-R10
I1 I2
10-5
10-6
4. Fill the 6 left holes with blanking plugs (Fig. 10-6)
10-7
10-Installation EN
28
Following connections are possible:
10.6.1 Drain hose to sink
▶Hang the drain hose with the U-support over the
edge of a sink with adequate size (Fig. 10-8).
▶Protect the U-support suciently against slip-
ping.
10.6.2 Drain hose to waste water connection
▶The internal diameter of the stand pipe with
vent-hole must be minimum 40 mm.
▶Put the drain hose for approx. 80 mm in the
wastewater pipe.
▶Attach the U-support and secure it suciently
(Fig. 10-9).
CAUTION!
▶The drain hose should not be submerged in water and should be securely xed and
leak-free. If the drain hose is placed on the ground or if the pipe is at a height of less
than 80 cm, the washing machine will continuously drain while being lled (self-si-
phoning).
▶Drain hose is not to be extended. If necessary contact after sales service.
10.6.3 Drain hose to sink connection
▶The junction must lie above the siphon
▶A spigot connection is usually closed by a pad (A).
That must be removed to prevent any disfunc-
tion (Fig. 10-10).
▶Secure the drain hose with a clamp.
10.6 Drain Water Connection
Fix the water drain hose properly to the piping. The hose has to reach at one point a height
between 80 and 100 cm above the appliance bottom line! If possible keep always drain
hose xed to the clip at the appliance back.
WARNING!
▶Use only the supplied hose set for the connection.
▶Never reuse old hose sets!
▶Only connect to cold water supply.
▶Before connection, check whether the water is clean and clear.
10-8 10-9
10-10
EN 10-Installation
29
10.8 Electrical Connection
Before each connection check if:
▶power supply, socket and fusing are appropriate to
the rating plate.
▶the power socket is earthed and no multi-plug or
extension are used.
▶the power plug and socket are strictly according.
▶Only UK: The UK plug meets BS1363A standard.
Put the plug into the socket (Fig. 10-13).
WARNING!
▶Ensure always that all connections (power supply, drain and fresh water hose) are rm,
dry and leack free!
▶Take care these parts are never to be crushed, kinked, or twisted
▶If the supply cord is damaged, it must be replaced by the service agent (see warranty
card) in order to avoid a hazard. .
10-13
10.7 Fresh Water Connection
Make sure that the gaskets are inserted.
1. Connect the water inlet hose with the angled
end to the appliance (Fig. 10-11). Tighten the
screw joint by hand.
2. The other end connect to a water tap with a
3/4“ thread (Fig. 10-12).
10-12
10-12
10-11
11-Technical data EN
30
Suppliers name or trade mark Haier
HW80-B14876 HW100-B14876
Rated capacity (kg) 8 10
A+++ A+++
Energy consumption per year (AEC in kWh/year) 1) 117 118
Energy consumption of standard cotton programme
60°C, full load (kWh/cycle) 0.54 0.50
Energy consumption of standard cotton programme
60°C, partial load (kWh/cycle) 0.56 0.56
Energy consumption of standard cotton programme
40°C, partial load (kWh/cycle) 0.46 0.50
0.42 0.45
Weighted power consumption of the left-on mode (W) 0.52 0.58
Water consumption per year (AWC in L/year) 2) 9500 11400
3) B
Max. spin speed (rpm) 4) 1330
Remaining moisture content (%) 4) 53
Standard 60°C cotton programme 5)
Cotton+ + 60°C + max. spin
Standard 40°C cotton programme 5)
Cotton+ + 40°C + max. spin
Programme time of cotton 60°C full load (min) 235 270
Programme time of cotton 60°C partial load (min) 233 265
Programme time of cotton 40°C partial load (min) 233 260
Duration of the left-on mode (TI in min) 6) 3
Airborne accustical noise (washing/spinning)
in dB(A) re 1pW 7) 53/66 53/65
Type freestanding
1) Based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and
the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is
used.
2) Based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load.
Actual water consumption will depend on how the appliance is used.
3)
4) Based on the standard 60°C cotton programme at full load and the standard 40°C cotton programme at
partial load.
5) “Standard 60°C cotton programme“ and “standard 40°C cotton programme“ are standard washing programmes
-
tion.
6) In case there is a power management system.
7) Based on the standard 60°C cotton programme at full load.
EN 11-Technical data
31
HW80-B14876 HW100-B14876
Dimension (HxDxW in mm) 845x460x595 845x530x595
Dimension (D in mm) 510 600
Voltage in V 220-240 V~/50Hz
Current in A 10
Max power in W 2000
Water pressure in MPa 0.03≤P ≤1
Netto weight in kg 72 77
11.2 Additional technical data
11.3 Standards and Directives
This product meets the requirements of all applicable EC directives with the correspon-
ding harmonised standards, which provide for CE marking.
12-Customer service EN
We recommend our Haier Customer Service and the use of original spare parts.
If you have a problem with your appliance, please rst check section TROUBLESHOOTING.
If you cannot nd a solution there, please contact
▶your local dealer or
▶the Service & Support area at www.haier.com where you can nd telephone numbers
and FAQs and where you can activate the service claim.
To contact our Service, ensure that you have the following data available.
The information can be found on the rating plate.
Model ____________________ Serial No. _____________________
Also check the Warranty Card supplied with the product in case of warranty.
For general business enquiries please nd below our addresses in Europe:
European Haier addresses
Country* Postal address Country* Postal address
Italy
Haier Europe Trading SRL
Via De Cristoforis, 12
21100 Varese
ITALY
France
Haier France SAS
3-5 rue des Graviers
92200 Neuilly sur Seine
FRANCE
Spain
Portugal
Haier Iberia SL
Pg. Garcia Faria, 49-51
08019 Barcelona
SPAIN
Belgium-FR
Belgium-NL
Netherlands
Luxembourg
Haier Benelux SA
Anderlecht
Route de Lennik 451
BELGIUM
Germany
Austria
Haier Deutschland GmbH
Hewlett-Packard-Str. 4
D-61352 Bad Homburg
GERMANY
Poland
Czechia
Hungary
Greece
Romania
Russia
Haier Poland Sp. zo.o.
Al. Jerozolimskie 181B
02-222 Warszawa
POLAND
United
Kingdom
Haier Appliances UK Co.Ltd.
One Crown Square
Church Street East
Woking, Surrey, GU21 6HR
UK
*For more information please refer to www.haier.com
32
EN 12-Customer service
European Haier addresses
Country* Postal address Country* Postal address
Italy
Haier Europe Trading SRL
Via De Cristoforis, 12
21100 Varese
ITALY
France
Haier France SAS
3-5 rue des Graviers
92200 Neuilly sur Seine
FRANCE
Spain
Portugal
Haier Iberia SL
Pg. Garcia Faria, 49-51
08019 Barcelona
SPAIN
Belgium-FR
Belgium-NL
Netherlands
Luxembourg
Haier Benelux SA
Anderlecht
Route de Lennik 451
BELGIUM
Germany
Austria
Haier Deutschland GmbH
Hewlett-Packard-Str. 4
D-61352 Bad Homburg
GERMANY
Poland
Czechia
Hungary
Greece
Romania
Russia
Haier Poland Sp. zo.o.
Al. Jerozolimskie 181B
02-222 Warszawa
POLAND
United
Kingdom
Haier Appliances UK Co.Ltd.
One Crown Square
Church Street East
Woking, Surrey, GU21 6HR
UK
33
34
GB
35
GB
HW80/100-B14876_V02_EN_190130
0020508374AA