Hannspree HG 324 QJB User Manual
Displayed below is the user manual for HG 324 QJB by Hannspree which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
User’s Manual OSD[V6.1]
2
Before operating the monitor, please read this manual thoroughly. This manual should be retained for
future reference.
FCC Class B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
The device complies with Parts 15 of the FCC Rule. Operation is subject to the following two
conditions﹕(1) this device may not cause harmful interference﹔and (2) this device must accept any
interference received, including interference that may cause undesired operations.
CANADA
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulation.
【Optional, depend on selected model】
This device complies with requirement of EMC directive 2014/30/EU with regard to
Electromagnetic Compatibility, and 2014/35/EU and 93/68/EEC with regard to Low Voltage
directive.
【Optional, depend on selected model】
Socket-outlet shall be near the equipment and shall be accessible.
Bemerkung zu den Warenzeichen:
HANNspree -Produkte beinhalten High-Definition Multimedia
Interface-(HDMI™) Technologie.
HDMI, das HDMI-Logo und High-Definition Multimedia Interface sind Marken oder eingetragene
Markenvon HDMI Licensing LLC in den Vereinigten Staaten und anderen Ländern.
HG324QJB
LCD Monitor
(HSG1381)
User’s Manual
2
Before operating the monitor, please read this manual thoroughly. This manual should be retained for
future reference.
FCC Class B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
The device complies with Parts 15 of the FCC Rule. Operation is subject to the following two
conditions﹕(1) this device may not cause harmful interference﹔and (2) this device must accept any
interference received, including interference that may cause undesired operations.
CANADA
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulation.
【Optional, depend on selected model】
This device complies with requirement of EMC directive 2014/30/EU with regard to
Electromagnetic Compatibility, and 2014/35/EU and 93/68/EEC with regard to Low Voltage
directive.
【Optional, depend on selected model】
Socket-outlet shall be near the equipment and shall be accessible.
Trademark Notice:
HANNspree products incorporate High-Definition Multimedia Interface
(HDMI TM) technology.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
User’s Manual
3
RECYCLING INFORMATION
We, the HANNspree care very much about our environment protection strategy and firmly believe
that it helps us have healthier earth via appropriate treatment and recycling of industrial technology
devices at the end-of-life.
These devices contain recyclable materials, which can be re-decomposed and re-integrated into
brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned
substances. We strongly encourage you to contact the provided information to recycle this product.
For more information, please visit
http://www.hannspree.eu/
User’s Manual
4
TABLE OF CONTENTS
SAFETY NOTICE .................................................................................................. 5
PRECAUTIONS ................................................................................................. 5
SPECIAL NOTES ON LCD MONITORS ...................................................... 6
BEFORE YOU OPERATE THE MONITOR ...................................................... 7
FEATURES ......................................................................................................... 7
CHECKING THE CONTENTS OF THE PACKAGE .................................. 7
INSTALLATION INSTRUCTIONS ................................................................ 8
POWER ............................................................................................................... 8
MAKING CONNECTIONS ............................................................................ 10
ADJUSTING THE VIEWING ANGLE .......................................................... 11
OPERATING INSTRUCTIONS ......................................................................... 12
GENERAL INSTRUCTIONS ......................................................................... 12
FRONT PANEL CONTROL .......................................................................... 13
HOW TO ADJUST A SETTINGS .................................................................. 14
PLUG AND PLAY ............................................................................................ 17
TECHNICAL SUPPORT (FAQ) ......................................................................... 18
Q & A FOR GENERAL PROBLEMS ........................................................... 18
ERROR MESSAGE & POSSIBLE SOLUTIONS ....................................... 20
APPENDIX ............................................................................................................ 22
SPECIFICATIONS .......................................................................................... 22
User’s Manual
5
SAFETY NOTICE
1. The changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the
emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment. It is the responsibilities of the user to correct such interference.
4. Only use attachments/accesories specified by the manufacturer.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high
voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified
personnel only.
PRECAUTIONS
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub,
swimming pool or in a wet basement.
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a
person and cause serious damage to the appliance. Use only a cart or stand recommended by the
manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure
reliable operation of the monitor and to protect it from overheating, be sure these openings are not
blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or
cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated on the label. If you
are not sure of the type of power supplied to your home, consult your dealer or local power
company.
Unplug the unit during a lighting storm or when it will not be used for long period of time. This
will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a
fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor by yourself; opening or removing covers can expose you to
dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.
The wall socket shall be installed near the equipment and shall be easily accessible.
User’s Manual
6
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the
Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or
less such as a missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may remain after
switching the image, when the same image is displayed for hours. In this case, the screen is
recovered slowly by changing the image or turning off the Power Switch for hours.
If the screen suddenly flashes erratically or the backlighting fails, please contact your dealer or
service center for repair. Do not attempt to repair the monitor yourself.
User’s Manual
7
BEFORE YOU OPERATE THE MONITOR
FEATURES
80cm /31.5”Wide Screen W-LED Backlight Monitor
Resolution 2560 x 1440 pixels
Ergonomic Design
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
LCD Monitor
Cables and User manual
Quick Start Guide
Warranty Card
EUR Energy Label
Power Cord
DP Cable
Screws
Screwdriver
User’s Manual
8
INSTALLATION INSTRUCTIONS
INSTALL
REMOVE
Figure.1. Installing and Removing the Base
INSTALLATION:
1. Align the Arm with the opening in the base.
2. Install the Arm on the base with 3 screws.
3. Install the Arm on Monitor with 4 screws.
4. Pendant snaps on the Arm and gently press down
REMOVAL:
1.Lift the pendant up
2.Remove the screws so that the stand base can be removed
3.Gently pull the stand base from the monitor until they are unattached.
4.Remove the screws,then gently remove the stand base.
Warm prompt: Place the Monitor face down on a soft and flat surface (blanket, foam, cloth, etc) to
Monitor while install and remove.
POWER
POWER SOURCE:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an Internal universal power supply that allows operation in either
100/120V AC or 220/240V AC voltage area (No user adjustment is required.)
3. Connect the AC-power cord one end to your LCD monitor’s AC-input socket, the other end to
wall-outlet.
User’s Manual
9
WALL MOUNTING THE MONITOR:
1. Purchase a VESA compatible wall bracket:
VESA 115×115, 4 holes, M4, 10mm, 8kg.
2. Locate your ideal Monitor position on the
wall.
3. Fix the wall bracket firmly on the wall.
4. Secure the Monitor to the bracket using the 4
mount holes on the back and center of the
Monitor.
Note:
Please read the instructions of your specific wall bracket to properly wall mount the Monitor.
The pitch of the mounting holes is 100mm horizontally and 100mm vertically.
The screws type required is metric: M4, 8mm length.
The Monitor stand base can be screwed on a table or a hard surface using the hole on the back of
the stand base.
For use only with UL listed wall mount bracket.
*Installing the LCD Monitor requires special skill that should only be performed by qualified service
personnel. Customers should not attempt to do the work themselves. HANNspree bears no
responsibility for improper mounting or mounting that results in accident or injury. You can ask a
qualified service personnel about using an optional bracket to mount the Monitor to the wall.
User’s Manual
10
MAKING CONNECTIONS
CONNECTING TO A PC
Turn off your computer before performing the procedure below.
1. Connect one end of the HDMI cable (optional) to the back of the monitor and connect the other
end to the computer’s HDMI port.
2. Connect one end of the DP cable to the back of the monitor and connect the other end to the
computer’s DP port.
3. Connect one end of the Mini DP cable to the back of the monitor and connect the other end to the
computer’s Mini DP port.
4. Connect the audio cable between the monitor audio output and the Speakers or Earphone.
5. Turn on your monitor and computer.
Figure.2. Connecting to a PC
1
HDMI Input
2
DP Input
3
Mini DP Input
4
LINE OUT
5
Power AC Input
User’s Manual
11
ADJUSTING THE VIEWING ANGLE
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the
monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the monitor’s angle.
You can adjust the monitor’s angle from -5 to 15.
You are able to adjust the monitor Height 135mm
You are able to adjust the monitor 45° for left and right
Figure.3. Monitor Angle
NOTES:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD
screen.
Be careful not to place fingers or hands near the hinges when tilting the monitor, otherwise
pinching can result.
User’s Manual
12
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are located on the rear
panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your
personal preferences.
The power cord should be connected.
Connect the Signal cable from the monitor to the VGA card.
Press the power button to turn on the monitor. The power indicator will light up.
Navigation key
Navigation key
Navigation key
Navigation key
Navigation key
Power Button
Figure.4. Control Panel Buttons
User’s Manual
13
FRONT PANEL CONTROL
Power Button:
Press this button to switch ON/OFF of monitor’s power.
Power Indicator:
Blue — Power On mode.
Amber — Power Saving mode.
The OSD Menu and OSD Quick-Menu Symbol explanations and their functional uses are
stated below.
NOTES:
Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a
place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
Save the original shipping box and packing materials, as they will come in handy if you ever have
to ship your monitor.
For maximum protection, repackage your monitor as it was originally packed at the factory.
To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be
removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents
such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
Activation symbol to turn the various modes on when operating
the menu system.
Activation symbol to exit, go back or deactivate the desired
function that is selected.
Toggle the selected options up and down the icon.
Symbol used to go back or revert back to the previously selected
menu.
Left and right icons toggle your selected choice horizontally.
Main menu icon that allows users access the main menu. Hold
down the icon for a few seconds to turn off the main menu.
Adjust the Contrast/Brightness.
User’s Manual
14
HOW TO ADJUST A SETTINGS
INPUT SELECT
MINIDP
DISPLAYPORT
HDMI2
HDMI1
Select the「INPUT SELECT」option to switch signals MiniDP,
DisplayPort, HDMI2, or HDMI1.
AUDIO ADJUST
VOLUME
Select the 「VOLUME」option to change the volume level. Enter
the option and adjust the level. [This function applies only to
models with incorporated audio.]
● By high volume, risk of hearing damage exists.
MUTE
Select the「MUTE」option to switch the function On or Off. [The
availability of this function depends upon the selected model.
Adjusting the volume while muted cancels Mute mode.]
VIEW MODE
(STANDARD)
LOW INPUT LAG
Select the「LOW INPUT LAG」option to switch the function On
or Off.
BLACK STABILIZATION
Select the「BLACK STABILIZATION」option to adjust the Black
Stabilization of the display. Set the value from 0 to 100.
ADVANCED CONTRAST
Select the「ADVANCED CONTRAST」option to adjust the
Advanced Contrast of the display. Set the value from 0 to 100.
RESPONSE TIME
Setup the display response time through the Response time
function. Available settings are Standard, Advanced, and Ultra
Fast. [This feature is limited to specific models only.]
RECALL
Resets the Standard monitor settings.
(GAME)
GAMER 1/ GAMER 2/ GAMER 3
LOW INPUT LAG
Select the「LOW INPUT LAG」option to switch the function On
or Off.
BLACK STABILIZATION
Select the「BLACK STABILIZATION」option to adjust the Black
Stabilization of the display. Set the value from 0 to 100.
ADVANCED CONTRAST
Select the「ADVANCED CONTRAST」option to adjust the
Advanced Contrast of the display. Set the value from 0 to 100.
RESPONSE TIME
Setup the display response time through the Response time
function. Available settings are Standard, Advanced, and Ultra
User’s Manual
15
Fast. [This feature is limited to specific models only.]
RENAME
Adjust the Rename value of the display according to your
preference. Select「RENAME」option to adjust the value.
RECALL
Resets the GAMER 1/ GAMER 2/ GAMER 3monitor settings.
FPS1/FPS2/RTS/MOBA
Select the mode according to your preference:
FPS1/FPS2/RTS/MOBA .
MOVIE/WEB/TEXT
Select the mode according to your preference: Movie/ Web/ Text.
COLOR ADJUST
CONTRAST
Adjust the contrast value of the display according to your
preference. Select「CONTRAST」option to adjust the contrast
value.
BRIGHTNESS
Adjust the brightness value of the display according to your
preference. Select「BRIGHTNESS」option to adjust the brightness
value.
COLOR TEMPERATURE
Adjust the color temperature value of the display according to
your preference: sRGB/Bluish/Cool/Native/Warm/User
Color/Low Blue Enable/ Low Blue Adjust.
COLOR SPACE
Adjust the Color Space value of the display according to your
preference:Auto/RGB Mode/YUV Mode.
COLOR RANGE
Adjust the Color Range value of the display according to your
preference:Auto/Full Range/Limited Range .
MANUAL IMAGE ADJUST
SHARPNESS
Select the「Sharpness」option to adjust the sharpness of the display.
Set the value from 0 to 100.
ASPECT RATIO
When the aspect ratio of screen is distorted, you may make
adjustments by using this function.「FULL SCREEN」indicates
full screen display, which does not ensure the image is shown as is
or in initial scale. 「」indicates scaling by the proportion of
original images, which may cause the screen showing black
bands.
OVERSCAN
Select the「OVERSCAN」option to the function On or Off.
SETUP MENU
LANGUAGE SELECT
Select 「Language」 option to change the language of the OSD.
Enter the option and select a language. [Reference only, the OSD
Language depends on the selected model]
AMD FREESYNC
Select the「AMD FREESYNC」option to the function On or Off.
User’s Manual
16
RESOLUTION NOTICE
Select the「RESOLUTION NOTICE」option to the function On
or Off.
INFORMATION
Display Horizontal frequency/Vertical frequency/Resolution
information.
OSD TIMEOUT
Select 「OSD TIME-OUT」option to set the OSD time out from 5
to 60 seconds. Enter the option and adjust the level.
OSD BACKGROUND
Select the「OSD BACKGROUND」option to the function On or
Off.
POWER INDICATOR
Select the「POWER INDICATOR」option to the function On or
Off.
RAMPAGEX
Adjust the Rampagex value of the display according to your
preference:Red/Green/Blue/Auto/Off .
AUTO POWER OFF
Select the「AUTO POWER OFF」option to the function On or
Off.
SLEEP
Adjust the sleep mode value of the display according to your
preference .
ECO MODE
Adjust the ECO Mode value of the display according to your
preference: Standard/Optimize/Conserve.
DDC/CI
Select the 「DDC/CI」option to switch the function On or Off.
MEMORY RECALL
Select the 「MEMORY RECALL」option to reset to the monitor’
s factory setting.
User’s Manual
17
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD.
It allows the monitor to inform the host system of its identity and, depending on the level of DDC
used, communicate additional information about its display capabilities. The DDC2B is a
bidirectional data channel based on the I²C protocol. The host can request EDID information over the
DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE
MUST BE A VIDEO INPUT SIGNAL.
User’s Manual
18
TECHNICAL SUPPORT (FAQ)
Q & A FOR GENERAL PROBLEMS
PROBLEM & QUESTION
POSSIBLE SOLUTION
Power LED is not on
*Check if the Power Switch is in the ON position.
*Power Cord should be connected.
No Plug & Play
*Check if the PC system is Plug & Play compatible.
*Check if the Video Card is Plug & Play compatible.
*Check if any plug pins on the DP or HDMI
connector are bent.
The display is too dark or too bright.
*Adjust the Contrast and Brightness Controls.
Picture bounces or a wave pattern is
present in the picture
*Move electrical devices that may cause electrical
interference.
The power LED is ON (Amber) but
there’s no video or no picture.
*Computer Power Switch should be in the ON
position.
*Computer Video Card should be snugly seated in its
slot.
*Make sure monitor’s video cable is properly
connected to the computer.
*Inspect monitor’s video cable and make sure none
of the pins are bent.
*Make sure computer is operational by hitting the
CAPS LOCK key on the keyboard while observing
the CAPS LOCK LED. The LED should either turn
ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary colors (RED,
GREEN, or BLUE)
*Inspect the monitor’s video cable and make sure that
none of the pins are bent.
Screen image is not centered or sized
properly.
* Adjust pixel frequency CLOCK and PHASE or
press hot-key ( i Button).
Picture has color defects
(White does not look white)
*Adjust RGB color or select color temperature.
The screen resolution needs to be adjusted
*Use win 2000/ME/XP Right click anywhere on
desktop and select Properties>Settings>Screen
Resolution. Use the silder to adjust the reslution
and click Apply.
User’s Manual
19
Addendum related to Windows 7 / Windows 8
When you encounter display problem under Windows 7/ Windows 8, you need to do the following:
1. Make sure your PC computer (Hardware requirement) can support Windows 7/ Windows 8.
2. Make sure your video card can run Windows 7/ Windows 8.
3. If your video card can support Windows 7/ Windows 8, need to install the latest Windows 7/
Windows 8 driver of your video card.
Suggest to do the following:
1. Install the latest Windows 7/ Windows 8 video driver of your video card.
2. Try to use the recommended display resolution that is supported by the monitor.
3. If the recommended display resolution is not working, try the second recommended display
resolution.
1
2
35,56cm / 14”
(16:9)
1366×768@60Hz
1366×768@50Hz
39,6cm / 15.6”
(16:9)
1366×768@60Hz
1366×768@75Hz
40,64cm / 16”
(16:9)
1366×768@60Hz
1366×768@50Hz
43,2cm / 17”
(16:10)
1440×900@60Hz
1440×900@75Hz
47cm / 18.5” (16:9)
1366×768@60Hz
1366×768@75Hz
48,3cm / 19” (5:4)
1280×1024@60Hz
1280×1024@75Hz
48,3cm /
19”(16:10)
1440×900@60Hz
1440×900@75Hz
51cm / 20” (16:9)
1600×900@60Hz
1600×900@50Hz
56cm / 22” (16:10)
1680×1050@60Hz
1680×1050@50Hz
54,6cm / 21.5”
(16:9)
60cm / 23.6” (16:9)
60.45cm/23.8”(16:9
)
62,5cm/ 24.6 (16:9)
1920×1080@60Hz
1920×1080@50Hz
68.6cm / 27” (16:9)
1920×1080@60Hz
1920×1080@50Hz
80cm/31.5”(16:9)
2560x1440@60Hz
2560x1440@75Hz
And if you still have display problem after doing the above procedure, please visit Hanns.G
support and Service Website: http://www.hannspree.eu/en/monitors
Windows is a registered trademark of Microsoft Corporation.
User’s Manual
20
ERROR MESSAGE & POSSIBLE SOLUTIONS
CABLE NOT CONNECTED:
1. Check that the signal-cable is properly connected, if the connector is loose, tighten the
connector’s screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode, set the computer to display mode given
in the following table.
FACTORY PRESET TIMING TABLE:
MODE
RESOLUTION
HORIZONTAL
FREQUENCY (KHz)
VERTICAL
FREQUENCY (Hz)
1
640×400 @70Hz
31.469
70.087
2
640×480 @60Hz
31.469
59.940
3
640×480 @70Hz
36.052
70.004
4
640×480 @67Hz
35.000
66.667
5
640×480 @72Hz
37.861
72.809
6
640×480 @75Hz
37.500
75.000
7
720×400 @70Hz
31.469
70.087
8
800×600 @56Hz
35.156
56.250
9
800×600 @60Hz
37.879
60.317
10
800×600 @72Hz
48.077
72.188
11
800×600 @75Hz
46.875
75.000
12
832×624 @75Hz
49.725
75.000
13
1024×768 @60Hz
48.363
60.004
14
1024×768 @70Hz
56.476
70.069
15
1024×768 @75Hz
60.023
75.029
16
1152×870 @75Hz
68.681
75.062
17
1152×864 @75Hz
67.500
75.000
18
1280×720 @60Hz
45.000
60.000
19
1280×960 @60Hz
60.000
60.000
20
1280×960 @75Hz
74.592
74.443
21
1280×768 @60Hz
47.776
59.870
22
1280×768 @75Hz
60.289
74.893
23
1280×1024 @60Hz
63.981
60.020
24
1280×1024 @75Hz
79.976
75.025
25
1360×768 @60Hz
47.712
60.015
26
1440×900 @60Hz
55.469
59.901
27
1440×900 @75Hz
70.635
74.984
28
1400×1050 @60Hz
64.744
59.948
User’s Manual
21
29
1680×1050 @60Hz
65.290
59.954
30
1920×1080 @60Hz
67.500
60.000
31
2560×1 440 @60Hz
88.787
59.951
User’s Manual
22
APPENDIX
SPECIFICATIONS
LCD Panel
Driving system
TFT Color LCD
Size
80cm /31.5” Diagonal
Pixel pitch
0.0908(H) x 0.2724(V) mm
Video
H-Frequency
31KHz – 215KHz
V-Frequency
56Hz – 144Hz
Display Colors
16.7M Colors
Max. Resolution
2560 x 1440 pixel / 144Hz
Plug & Play
VESA DDC2BTM
Power consumption
ON Mode
45W (Typical)
Power Saving Mode
≤0.5W
OFF Mode
≤0.3W
Audio output
Rated Power 1.5 W rms (Per channel)
Input Terminal
HDMI
DP
Mini DP
Maximum Screen Size
Hor. : 697.344mm
Ver. : 392.256mm
Power Source
100–240V , 50–60Hz
Environmental
Considerations
Operating Temp:5° to 35°C
Storage Temp.: -20° to 60°C
Operating Humidity: 20% to 85%
Dimensions
711.2 (W)×649.9 (H)×199.2 (D) mm
28.0”(W)×25.6 ”(H)×7.8”(D)
Weight (NW)
7.3 kg (16.1 lb)
*** The above specification is subject to actual product specification and is subject to change
without prior notice.
NOTES:
The Maximum Resolution will depends on the display card supporting. Related issue can refer to
http://www.hannspree.eu/en/monitors. FAQ section.