Hoover HDI 1LO38B-80 User Manual

Displayed below is the user manual for HDI 1LO38B-80 by Hoover which is a product in the Dishwashers category. This manual has pages.

Related Manuals

Hoover HDIN 4S613PS-80 Manual

Hoover HDIN 2L360PB-80 Manual

Hoover HDIN 4D620PB-80 Manual

Hoover HDI 3DO623D-80 Manual

Hoover HDI 2T623PWF-80 Manual

Hoover HDIN 4D620PB Manual

Hoover HDI 30 Manual

Hoover HDIMC30 Manual

User instructions

DISHWASHER

CONTENTS

General safety rules

Installation (Technical notes for cabinet fitters)

Water connection

Loading the salt

Adjusting the upper basket

Loading the dishes

Information for test laboratories

Loading the detergent

Types of detergent

Loading the rinse aid

Cleaning the filters

Some practical hints

Routine cleaning and maintenance

Description of the control panel

Technical data

Programme selection and special functions

One Touch

Programme guide

Water softener unit

Identifying minor faults

Your guarantee

pag. 4

pag. 6

pag. 9

pag. 11

pag. 12

pag. 13

pag. 15

pag. 16

pag. 17

pag. 18

pag. 19

pag. 20

pag. 21

pag. 22

pag. 23

pag. 26

pag. 28

pag. 30

pag. 31

pag. 33

Please read the instructions in this booklet carefully because they contain important

information on how to install, use and maintain your dishwasher safely as well as

containing useful tips on how to make the most of it.

Keep this booklet safe for future reference.

Fig. A

GENERAL SAFETY RULES

■This appliances is intended to be

used in household and similar

applications such as:

- staff kitchen areas in shops,

offices and other working

environments;

- farm houses;

- by clients in hotels, motels

and other residential type

environments;

- bed and breakfast type

environments.

A different use of this appliance

from household environment or

from typical housekeeping

functions, as commercial use by

expert or trained users, is

excluded even in the above

applications.

If the appliance is used in a

manner inconsistent with this

it may reduce the life of the

appliance and may void the

manufacturer’s warranty.

Any damage to the appliance or

other damage or loss arising

through use that is not consistent

with domestic or household use

(even if located in a domestic or

household environment) shall not

be accepted by the manufacturer

to the fullest extent permitted by

law.

■This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance in

a safe way and understand the

hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made

by children without supervision.

■Children should be supervised to

ensure that they do not play with

the appliance.

■Children of less than 3 years

should be kept away unless

continuously supervised.

■Should it be necessary to replace

the supply cord, call the After

Sales Service Centre.

■The appliance must be connected

to the water mains using new

hose-sets. The old hose-sets

should not be reused.

■Water pressure must be between

0,08 MPa and 0,8 MPa.

■When the appliance is located on

a carpet floor, attention must be

paid to ensure that there is no

obstruction to the bottom vents.

■After installation, the appliance

must be positioned so that the

plug is accessible.

■For the maximum place loading,

please refer to the "TECHNICAL

DATA" table/section.

WARNING !

Knives and other utensils with

sharp points must be loaded

in the basket with their points

down or placed in a horizontal

position.

■The door should not be left in the

open position since this could present

a potential hazard ( e.g. tripping ).

■To consult the product fiche please

refer to the manufacturer website.

Safety instructions

■Make sure the electrical system

is grounded. Otherwise, seek

qualified professional assistance.

Manufacturer declines all

responsibility for any damage

due to non-earthing of the

machine.

■Ensure that the dishwasher does

not crush power cables.

■In general it is not advisable to use

adaptors, multiple plugs and/or

extension cables.

■Do not remove the plug from the

mains supply socket by pulling the

mains cable or the machine itself.

■Do not leave the appliance expo-

sed to the elements (rain, sun etc).

■Leaning or sitting on the open

door of the dishwasher could

cause it to tip over.

■The dishwasher is designed for

normal kitchen utensils. Objects that

have been contamined by petrol,

paint, traces of steel or iron, corrosi-

ve chemicals, acids or alkalis must

not be washed in the dishwasher.

■If there is a water softening device

installed in the home there is no

need to add salt to the water sof-

tener fitted in the dishwasher.

■If the appliance breaks down or

stops working properly, switch it

off, turn off the water supply and

do not tamper with it. Repair work

should only be carried out by an

approved service agent and only

genuine spare parts should be fit-

ted. Any failure to follow the above

advice may have serious conse-

quences for the safety of the

appliance.

■If it you need to move the machi-

ne after removing the packaging,

do not try to lift it by the bottom of

the door.

Open the door slightly and lift the

machine by holding on the top.

■For the installation of built-in

appliances, please refer to the

specific chapter or to the instruc-

tions enclosed with the booklet.

By placing the mark on this

product, we are confirming

compliance to all relevant

European safety, health and

environmental requirements

which are applicable in legislation

for this product.

■Once the height of the dishwasher has

been defined, it is necessary to fix a

13 mm long screws "A" in the

bottom-frame. This should only be done

on the front feet, as indicated in the

figure 4a.

■To allow for easy adjustment of the

appliance when it is fitted into the cavity,

SOME MODELS are fitted with an adjustable

foot located centrally at the rear. This

can be adjusted by turning a screw

located at the bottom of the front panel of

the machine, as illustrated in fig. 4b.

INSTALLATION

(Technical notes for cabinet

fitters)

This dishwasher model can be embedded

in modular furniture, under a counter top, a

continuous counter top or a sink.

■The housing dimensions must be the

same as those indicated in the figure 1.

■The adjustable feet allow the height of

the machine to be varied from 818 to

898 mm.

Installation under the counter top

■Apply the steam protection adhesive

tape under the counter top when it is

made of chipboard or of any other

non-waterproof material (fig. 2).

■Insert the dishwasher in the housing "A"

then adjust the height and level it by

means of the adjustable feet (fig. 2-3).

■Connect the dishwasher to water and

power following the instruction booklet.

■You should secure the dishwasher into

the housing unit. It is possible to do this

in the following ways:

-THROUGH THE ADJOINING

HOUSING UNIT with the supplied

16 mm long screws "B" (as indicated

in the figure 5).

-TO THE WORKTOP (if possible) with

the supplied 30 mm long screws "C"

(as indicated in the figure 5a).

Wooden panel installation

This dishwasher model is equipped with an

auto-balancing system in the door and

comes ready to mount a wooden panel of

the following size:

Width 596,5 mm max

Height from 645 to 720 mm max

Thickness from 18 to 22 mm max

This allows the use of a regular wing taken

from a drawer furniture weighing from 3 to

8 kg; for coverings weighing more, ask for

information to the Assistance Service.

N.B.:

If you wish to fit a wooden panel with

false drawer, ask for special kit to the

Assistance Service.

Drilling arrangements

■Drill 12 mm deep holes in the panel

using a 2 mm diameter drill according to

the measures indicated in the figure 6.

■Fasten the two supplied frames with 4 of

the 4 x 16 mm diameter screws, setting

them at the center of the eyelets (fig. 7).

■Hang the panel on the dishwasher door

and align it by adjusting the frames with

the eyelets.

■Fix the frames with the other 6 screws

4x16 mm in the specif holes (fig. 7).

■Fasten the panel to the dishwasher door

with the screws 3.5 x 13 mm (fig. 8).

720 max.

645 min.

350 178

596,5 max.

=572

55a

620 min.

lower edge on the base with a pencil; cut

out the interfering part.

FOR MODELS FITTED WITH CANTILEVERED

HINGES the rotation requires only a 3

mm space therefore normally no cut out

is required as shown in fig. 9a.

Adaptation of the base

Sometime, in order to allow the door

rotation, a space must be cut out in the

base as indicated in the figure 9.

Proceed as follows:

■Open slightly the dishwasher door, let

the covering touch the base and mark its

WATER CONNECTION

IMPORTANT

The appliance must be connected to

the water mains using new hose-sets.

The old hose-sets should not be reused.

■The inlet and drain hoses can be directed

to left or right.

IMPORTANT

The dishwasher can be connected to

either cold or hot water, as long as it

is no hotter than 60°C.

■Water pressure must be between

0,08 MPa and 0,8 MPa.

■The inlet hose must be connected to a

tap so that the water supply can be cut

off when the machine is not in use

(fig. 1 B).

■The dishwasher is fitted with 3/4" threaded

connector (fig. 2).

■Connect inlet hose “A” to water tap “B”

with a 3/4" attachment making sure that

it has been properly tightened.

■If it is necessary, the inlet pipe can be

lengthened up to 2,5 m. The extension

pipe is available from the After Sales

Service Centre.

■If the dishwasher is connected to new

pipes or to pipes which have not been in

use for a long time run water through for

a few minutes before connecting the

inlet hose. In this way no deposits of

sand or rust will clog up the water inflow

filter.

Connecting the outlet hose

■The outlet hose should disharge into a

standpipe, making sure that there are no

kinks (fig. 4).

■The standpipe must be at least 40 cm

above floor level and it must have an

internal diameter of at least 4 cm.

■It is advisable to fit an anti-odour air trap

(fig. 4X).

■If necessary the outlet hose can be

extended up to 2,5 m, provided that it is

kept at a maximum height of 85 cm

above floor level. The extension pipe is

available from the After Sales Service

Centre.

■The hose can be hooked over the side of

the sink, but it must not be immersed in

water, in order to prevent water from

being syphoned back to the machine

when this is in operation (fig. 4Y).

■When installing the appliance under a

worktop the hose pipe clamp must be

attached to the wall in the highest possible

position under the worktop (fig. 4Z).

■Check that there are no kinks in the inlet

and outlet hoses.

LOADING THE SALT

■The appearance of white stains on dishes

is generally a warning sign that the salt

container needs filling.

■On the bottom of the machine there is a

container for the salt for regenerating

the softener.

■It is important to use only a salt that is

specifically designed for dishwasher.

Other types of salt contain small quantities

of insoluble particles which over a long

period of time may affect and deteriorate

the softener performance.

■To add salt, unscrew the cap of the con-

tainer on the bottom and then refill the

container.

■During this operation a little water will

overflow; but keep adding salt until the

container is full. When the container is

full, clean the thread of salt residue and

retighten the tap.

■After loading the salt, it is recommended

running a complete washing cycle,

or COLD RINSE programme.

IMPORTANT

After loading the salt, YOU

MUST run a complete washing

cycle, or the PRE-WASH/COLD

RINSE/REFRESH programme.

■The salt dispenser has a capacity of

between 1.5 and 1.8 kg and, for efficient

use of the appliance, it should be refilled

from time to time according to the

regulation of the water softener unit.

IMPORTANT

(Only for first start up)

When the appliance is used for the

first time, after completely filling the

salt container, it is necessary to add

water until the container overflows.

ADJUSTMENT OF THE

UPPER BASKET

If 29 cm to 32,5 cm plates are normally

used, load them onto the lower basket after

the upper basket has been placed in its

upper position and proceed as detailed

below:

1. Turn the front stops “A” outwards;

2. Take out the basket and remount it in the

upper position;

3. Replace the blocks “A” in their original

position.

Dishes that are bigger than 20 cm in

diameter can no longer be loaded onto the

upper basket and the mobile supports

cannot be used when the basket is in the

upper position.

LOADING DISHES

Using the upper basket

■The upper basket is provided with

mobile racks hooked to the sides of the

basket, which can be regulated into 4

positions.

■In the lowered position (A-A1) the racks

may be used for such items as: tea and

coffee cups, kitchen knives and ladles.

Also glasses with stems may be safely

hung on the ends of the racks.

■In the upright position (B-B1) the racks

allow you to load dinner plates and soup

plates. Plates should be loaded

vertically with the underside of the plate

towards the back of the dishwasher with

a space between each plate to allow

water to pass freely.

■It is advisable to load large plates

(approx. 26 or more cm) slightly tilted

towards the rear to facilitate introduction

of the basket into the machine.

■Salad bowls and plastic bowls may also

be loaded on the upper basket. It is

advisable to block these in place so that

the jets of water do not make them

overturn.

■The upper basket has been designed to

offer maximum flexibility in use and can

be loaded with up to 24 plates on two

rows, up to 30 glasses on five rows or a

mixed load.

BB1

AA1

A standard daily load is represented in

figs. 1, 2 and 3.

Upper basket (fig. 1)

A= soup plates

B= dinner plates

C= dessert plates

D= saucers

E= cups

F= glasses

Upper basket (fig. 2)

A= soup plates

B= dinner plates

C= dessert plates

D= saucers

E= cups

F= glasses

G= single section cutlery basket

ABCD

Upper basket (fig. 3)

A= glasses

B= saucers

C= cups

D= small bowl

E= medium bowl

F= large bowl

G= serving spoons

Using the lower basket

■Saucepans, oven dishes, tureens, salad

bowls, lids, serving dishes, dinner

plates, soup plates and ladles can be

loaded on the lower basket.

■Place the cutlery in the plastic cutlery

holder with the handles pointing

upwards.

■Place the cutlery holder on the lower

basket (fig. 4 and 5), making sure that

the cutlery does not get in the way of the

rotating arms.

IMPORTANT

The lower basket has a safety-stop

device, for its safe extraction, also

especially useful with a full load.

For loading salt, cleaning filter and for

ordinary maintenance, the complete

extraction of the basket is necessary.

Please load the dishwasher sensibly to

ensure the best wash results.

A standard daily load is represented in

figs. 4 and 5.

Lower basket (fig. 4)

A= medium-sized saucepan

B= large saucepan

C= frying pan

D= lids

E= tureens, serving dishes

F= cutlery

G= oven dishes

Lower basket (fig. 5)

A= soup plates

B= dinner plates

C= dessert plates

D= serving dish

E= cutlery

DFAG

Cutlery basket (fig. 6)

The cutlery basket is made with two

detachable parts which will enable various

loading options.

The two parts can be detached by sliding

the left section away from the right section.

The top of cutlery basket can be removed,

for enable various loading options.

INFORMATION FOR THE TEST LABORATORIES

Please ask information required for comparison testing and measuring noise levels, according

to EN normative, to the following address:

testinfo-dishwasher@candy.it

In the request, please specify model name and number of the dishwasher (see rating plate).

LOADING THE DETERGENT

The detergent

IMPORTANT

It is essential to use a detergent

that is specifically designed for

dishwashers either in powder, liquid

or tablet form.

Unsuitable detergents (like those for

washing up by hand) do not contain the

proper ingredients for use in a dishwasher,

and stop the dishwasher from working

correctly.

Filling the detergent container

The detergent container is inside the door

(fig. A “2”). If the lid of the container is

closed, press the button (A) to open.

At the end of every wash cycle the lid is

always open and ready for the next time

the dishwasher is used.

WARNING!

When loading the lower basket, please

ensure that the plates or others do not

obstruct the detergent dispenser.

The amount of detergent to be used varies

according to how dirty the dishes are and

on the type of dishes to be washed.

We advise using 20÷30 g of detergent in the

wash section of detergent compartment (B).

After pouring the detergent into the container,

close the lid, firstly pushing (1) and then

pressing on it (2) until you hear the click.

Since not all detergents are the same the

instructions on the boxes of detergent can

vary. We should just like to remind users

that too little detergent does not clean the

dishes properly whilst too much detergent

will not produce better results and is also a

waste.

IMPORTANT

Do not use an excessive amount of

detergent and help limit damage to

the environment at the same time.

TYPES OF DETERGENT

Detergent tablets

Detergent tablets of different manufacturers

dissolve at different speeds, for this

reason, during short programmes, some

detergent tablets may be not fully effective,

because they are not completely dissolved.

If these products are used, is recommended

to choose longer programmes to guarantee

the complete use of the detergent.

IMPORTANT

To get satisfactory washing results,

the tablets MUST be placed in the

wash section of the detergent

container and NOT directly in the

tub.

Concentrated detergents

The concentrated detergents, with reduced

alkalinity and with natural enzymes, in

conjunction with 50°C wash programmes,

have a smaller impact on the environment

and they protect the dishes and the

dishwasher.

The 50°C wash programmes purposely

exploit the dirt-dissolving properties of the

enzymes, allowing therefore, with the use

of the concentrated detergents, to achieve

the same results of the 65°C programmes

but at a lower temperature.

Combined detergents

The detergents that also contain the rinse

aid must be placed in the wash section of

the detergent container. The rinse aid

container must be empty (if it is not empty,

set the rinse aid regulator to lowest position

before using combined detergents).

"ALL in 1" combined detergents

If you are planning to use “ALL in 1” (“3 in 1 “/

“4 in 1”/ “5 in 1”, etc.) combined detergents i.e.

those with built in salt and/or rinse agent,

we would advise the following:

■read carefully and follow the manufacturer’s

instructions given on the packaging;

■the effectiveness of detergents containing

the built in water softener/salt depends

on the hardness of your water supply.

Check that the hardness of your water

supply is within the effective range given

on the detergent packaging.

If when using this type of product, you

don't get satisfactory washing results,

please contact the detergent

manufacturer.

In certain circumstances use of combined

detergents can cause:

■limescale deposits on dishes or in the

dishwasher;

■a reduction in washing and drying

performance.

IMPORTANT

Any problems which arise as a direct

result of the use of these products

are not covered by our warranty.

Please note that using the "ALL in 1"

combined detergents, the rinse aid and

salt indicator lights (only used on

selected models) are superfluous, so you

must ignore the lights.

If washing and/or drying problems occur,

we recommend you return to use traditional

separate products (salt, detergent and

rinse agent). This will ensure that the water

softener in the dishwasher operates

correctly.

In this case, we recommends that you:

■refill both the salt and rinse aid container;

■run one normal washing cycle without a

load.

Please note that on return to the use of

conventional salt, a number of cycles will

be required before the system becomes

fully efficient again.

LOADING THE RINSE AID

The rinse aid

The rinse aid, which is automatically

released during the last rinsing cycle, helps

the dishes to dry quickly and prevents

spots and stains forming.

Filling the rinse aid container

The rinse aid container can be found to the

left of the detergent container (fig. A "3").

To open the lid, push the reference mark

and, in the same time, pull the tab of

opening.

It is always advisable to use rinse aid that

is specifically designed for dishwasher.

Check the rinse aid level through the

indicator eye (C) which is located on the

dispenser.

Regulating the rinse aid from 1 to 6

The regulator (D) is placed under the lid

and can be turned using a coin.

The recommended position is 4.

The limestone content of the water

considerably affects the formation of

limescale and the drying performance.

It is therefore important to regulate the

quantity of rinse aid to achieve good

washing results.

If, after the wash, streaks occur on the

dishes, decrease the amount by one

position. If whitish spots occur, increase the

amount by one position.

FULL EMPTY

dark light

CLEANING THE FILTERS

The filter system (fig.A “4”) consists of:

a central container that traps the larger

particles;

a flat gauze that continuously filters the

wash water;

a micro filter, located beneath the gauze,

that traps the tiniest particles ensuring a

perfect rinse.

■To achieve excellent results every time,

the filters should be checked and

cleaned after each wash.

■To remove the filter unit, simply turn the

handle anticlockwise (fig. 1).

■For ease of cleaning, the central container

is removable (fig. 2).

■Remove the gauze filter (fig.3) and

wash the whole unit under a jet of

water. If necessary a small brush can

be used.

■With the Self-cleaning Micro filter,

maintenance is reduced and the filter

unit need only be checked every two

weeks. Nevertheless, after each wash it

is advisable to check that the central

container and the gauze filter are not

clogged.

WARNING!

After cleaning the filters, make sure

that they are correctly reassembled

and that the gauze filter is properly

positioned at the bottom of the

dishwasher.

Make sure that the filter is screwed

back, clockwise, into the gauze, as

poor seating of the filter unit could

have an adverse effect on the

efficiency of the appliance.

IMPORTANT

Never use the dishwasher without

the filters.

PRATICAL HINTS

How to get really good wash

results

■Before placing the dishes in the

dishwasher, remove any remaining

food (bones, shells, pieces of meat or

vegetables, coffee grounds, skin of fruit,

cigarette ash, tooth picks etc. to avoid

blocking the filters, water outlet and

washing arm nozzles.

■Try not to rinse the dishes before

loading them into the dishwasher.

■If saucepans and oven dishes are

encrusted with the remains of burnt or

roast food, it is advisable to leave them

to soak before washing.

■Place the dishes face downwards.

■Try to place the dishes in such a way

that they are not touching one another.

If they are loaded properly you will get

better results.

■After loading the dishes check that the

washing arms can rotate freely.

■Pans and other dishes that have

particularly stubborn food particles or

remnants of burnt food should be left to

soak in water with dishwasher

detergent.

■To wash silver properly:

a) rinse the silver immediately after

use, especially if it has been used for

mayonnaise, eggs, fish etc.;

b) do not sprinkle detergent onto it;

c) keep it separate from other metals.

How to make savings

■If you want the dishwasher to give a

complete wash, place the dishes in the

dishwasher at the end of each meal and

if necessary turn on the COLD RINSE

cycle to soften the food remains and

remove bigger particles of food from the

new load of dishes.

When the dishwasher is full start the

complete wash cycle programme.

■If the dishes are not very dirty or if the

baskets are not very full select an

ECONOMY programme, following the

instructions in the program list.

What not to wash

■It should be remembered that not all

dishes are suitable for washing in a

dishwasher.We advise against using

the dishwasher to wash items in

thermoplastic, cutlery with wooden or

plastic handles, saucepans with

wooden handles, items in aluminium,

crystal, leaded glass unless otherwise

stated.

■Certain decorations may fade. It is

therefore a good idea before loading the

whole batch to wash just one of the

items first so as to be sure that others

like it will not fade.

■It is a good idea not to put silver cutlery

with non-stainless steel handles into

the dishwasher as there could be a

chemical reaction between them.

IMPORTANT

When buying new crockery or

cutlery always make sure that they are

suitable for washing in a dishwasher.

Useful hints

■In order to avoid any dripping from the

top rack, remove the lower rack first.

■If the dishes are to be left in the

machine for some time, leave the door

ajar, to let some air circulate and to

improve the drying performance.

WHEN CYCLE IS FINISHED

After every wash it is essential to turn off

water supply and to switch off the machine

by pressing the On/Off button to the off

position.

If the machine is not going to be used for

some time, it is advisable to follow these

rules:

1. do an empty wash with detergent in order

to clean the machine of any deposits;

2. pull out the electric plug;

3. turn off the water tap;

4. fill the rinse aid container;

5. Ieave the door ajar;

6. keep the inside of the machine clean;

7. If the machine is left in places where the

temperature is below 0°C any water left

inside the pipes may freeze. Wait until

the temperature rises above zero and

then wait for about 24 hours before

starting up the dishwasher.

CLEANING AND

MAINTENANCE

■To clean the dishwasher outside, do not

use solvents (degreasing action) neither

abrasives, but only a cloth soaked with

water.

■The dishwasher does not require special

maintenance, because the tank is

self-cleaning.

■Regularly wipe the door gasket with a

damp cloth to remove any food remains

or rinse aid.

■Dishwasher cleaning is recommended,

in order to remove limestone deposits or

dirt. We suggest you run a washing cycle

periodically with specialist dishwasher

cleaning products. For all cleaning

operations the dishwasher must be

empty.

■If, in spite of the routine cleaning of the

filters, you notice that the dishes or pans

are not properly washed or rinsed, check

that all the spray heads on the rotor

arms (fig. A “5”) are clear.

If they are blocked, clean them in the

following way:

1. to remove the upper rotor arm, turn it

until it lines up with the stop marked

by the arrow (fig. 1b). Push it upwards

(fig. 1) and, keeping it pushed in,

unscrew it in a clockwise direction

(to reassemble it repeat the same

operation, but turn it anticlockwise).

The lower rotor arm can be removed

simply by pulling it upwards (fig. 2);

2. wash the rotor arms under a jet of water

to clear any blockage in the spray

heads;

3. when you have finished, refit the rotor

arms in the same position, remembering

to re-align the arrow and screw into

position.

■Both the door lining and the tank lining

are in stainless steel; however, should

spots caused by oxidation occur, this is

probably due to a high level of iron salts

presents in the water.

■The spots can be removed with a mild

abrasive agent; never use chlorine

based materials, steel wool, etc.

DESCRIPTION OF THE CONTROL PANEL

A"ON/OFF" button

B"PROGRAMME SELECTION" button

C "DELAY START" button

D "SUPER ECO" option button

E "RESET" button for

"SALT EMPTY" light

F"START"/"RESET" button

(start/cancelling programme)

G "SALT EMPTY" light

H "OPTION SELECTION" light

I "PROGRAMME STATUS" lights/

"DELAY START" time lights

L"PROGRAMME SELECTION" lights

M Programme guide

N ONE TOUCH area

DIMENSIONS

TECHNICAL DATA

CONSUMPTION (main programmes)*

Programme Energy (kWh) Water (L)

INTENSIVE

UNIVERSAL

ECO

RAPID 29'

Width x Height x Depth (cm)

Depth with door open (cm)

EN 50242 place load

Capacity with pans and dishes

Water supply pressure (MPa)

Fuse / Power input / Supply voltage

8 persons

Min. 0,08 - Max. 0,8

See rating plate

Power consumption of the off-mode and of the left-on mode: 0,45 W / 0,45 W

*Values are measured in a laboratory according to European Standard EN 50242 (consumption may

vary according to conditions of usage).

2,08

1,53

1,04

0,73

20,5

14,5

59,8 x 81,8 ÷ 89,8 x 55

117

WARNING!

If you open the door during the

drying cycle, an audible audio signal

advises you that the drying cycle has

not yet finished.

Changing a running programme

Proceed as follows to change or cancel a

running program:

■Open the door.

■Hold the "RESET" button down for at

least 3seconds.

Some audible signals will sound and the

programme indicator lights will turn on

and off individually and sequentially.

■The running programme will be cancelled

and all the programme indicator lights will

flash.

■At this point a new programme can be set.

WARNING!

Before starting a new programme,

you should check that there is still

detergent in the dispenser.

If necessary, top up the dispenser.

Programme operations

When a programme is running the relevant

indicator light will remain on and the 3

“PROGRAMME STATUS” indicator lights

("WASH" , "RINSE" , and "DRY" )

will light singularly and in sequence to

indicate the current phase.

If there is any break in the power supply

while the dishwasher is operating, a

special memory stores the selected

programme and, when the power is

restored, it continues where it left off.

Programme end

A 5 second alarm will sound (if not muted)

3 times at 30 second intervals and the

programme indicator light will flash to

indicate that the washing programme has

finished. The dishwasher will automatically

switch off.

PROGRAMME SELECTION

AND SPECIAL FUNCTIONS

(Use in conjunction with programme guide)

Programme settings

■Open the door and place the dirty dishes

inside the appliance.

■Press the "ON/OFF" button for about 2

seconds.

All the programme indicator lights will

flash.

■Choose a programme by pressing the

"PROGRAMME SELECTION" button.

The selected program indicator light will

flash.

■If you wish to select an option, press the

option button (the corresponding indicator

light will light up).

The option button can be selected or

deselected WITHIN one minute of the

programme commencing.

■Press the "START" button (the selected

programme indicator light will stop

flashing and remain on.

■Close the door (after an audible signal

has sounded, the programme will start

automatically).

WITHIN one minute of the programme

commencing, another programme

can be selected, simply by pressing

the "PROGRAMME SELECTION"

button.

Programme interruption

Opening the door when a programme is

running is not recommended especially

during the main wash and final hot rinse

phases. However, if the door is opened

while a programme is running (for example,

to add dishes) the machine stops

automatically.

Close the door, without pressing any

buttons. The cycle will start from where it

left off.

Option buttons

"SUPER ECO" button

This button provides an energy and time

saving of 25% on average (according to

the select cycle) reducing the wash water

temperature and the drying time during the

final rinse.

This programme is recommended for light

soil washes, and for slightly wet dishes that

are not fully dry, & improved drying results.

We advise you to leave the door of the

Dishwasher half-open at the end of the

cycle, to allow for a natural circulation of air

inside the dishwasher.

Salt empty indicator

This model is provided with an indicator

light on the control panel which will light up

when it is necessary to reload the salt

container.

The appearance of white stains on dishes

is generally a warning sign that the salt

container needs filling.

"RESET" button for

"SALT EMPTY" light

After filling the salt container, you should

press this button for a few seconds, until

the corresponding indicator light switches

off.

WARNING!

If you press the reset button without

filling the salt container, this will

interfere with the correct functioning

of the salt indicator light.

IMPORTANT

In order to guarantee the correct

functioning of the salt indicator

light, YOU MUST ALWAYS FULLY

REPLENISH THE SALT CONTAINER.

"DELAY START" button

The dishwasher start time can be set with

this button, delaying the start by 3, 6 or 9

hours.

Proceed as follows to set a delayed start:

■Choose a programme by pressing the

"PROGRAMME SELECTION" button.

■ Press the "DELAY START" button (each

time the button is pressed the start

will be delayed by 3, 6 or 9 hours

respectively and the corresponding time

indicator light will illuminate).

■To start the countdown, press the

"START" button (the set time indicator

light will start to flash).

If a 9 hour delay is set, countdown will be

displayed by the 6h indicator light after 3

hours and the 3h indicator light after 6

hours.

At the end of the last 3 hours (at the end

of countdown) the 3h indicator light will

stop flashing and remain on to indicate the

washing phase and the programme will

start automatically.

If countdown has not ended, whereby

the programme has not yet started, it is

possible to change or cancel the delayed

start and select another programme or to

select/deselect the option button, proceeding

as follows:

■Hold the "RESET" button down for at

least 3seconds.

Some audible signals will sound and the

programme indicator lights will turn on

and off individually and sequentially.

■The delayed start and the selected

programme will be cancelled.

The programme indicator lights will flash.

■Press the "DELAY START" button to

set another delayed start time (the

corresponding indicator light will turn on).

■A new programme can be set after a

delayed time has been changed or

cancelled or an option button can be

selected or deselected.

Alarm mute for the PROGRAMME

END

The alarm for the programme end may be

muted as follows:

IMPORTANT

The dishwasher must ALWAYS be off

before start of this procedure.

1. Hold down the "PROGRAMME

SELECTION" button and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME SELECTION"

button pressed for at least 15 seconds

(during this time, 2audible signals will

sound).

3. Release the button when the second

audible signal sounds (3 "PROGRAMME

SELECTION" indicator lights will come

on).

4. Press the same button again: the 3

indicator lights (which indicate that the

alarm is activated) will start flashing (to

indicate that the alarm is off).

5. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

To turn the alarm on again, follow the same

procedure.

Memorization of the last

programme used

The last programme used can be memorized

by following the below:

IMPORTANT

The dishwasher must ALWAYS be off

before start of this procedure.

1. Hold down the "PROGRAMME

SELECTION" button and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME SELECTION"

button pressed for at least 30 seconds

(during this time, 3audible signals will

sound).

3. Release the button when the THIRD

audible signal sounds (all the indicator

lights will flash).

4. Press the same button again: the

flashing indicator light (memorization off)

will stop flashing and remain on

(memorization on).

5. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

To disable the memorization, follow the

same procedure.

Fault signals

If malfunctions or faults occur when a

programme is running the indicator light

that corresponds to the selected cycle

will flash rapidly and the alarm sounds.

In this event, turn the dishwasher off by

pressing the "ON/OFF" button.

After checking to make sure the water

inlet hose tap is open, that the drain

hose is not bent and that the siphon or

filters are not clogged, set the selected

programme again.

If the anomaly persists, contact Customer

Service Department.

IMPORTANT

This dishwasher is equipped with an

anti-overflow safety device which will

automatically discharge any excess

water should a problem occur.

WARNING!

To ensure the correct operation of

the anti-overflow safety device, we

recommend that the dishwasher is

not moved or tilted during operation.

If however it is necessary to tilt or

move the dishwasher, please ensure

that the washing cycle is complete

and that there is no remaining water

inside the dishwasher.

ONE TOUCH

This appliance is equipped with One

Touch technology that allows you to

interact, via the App, with smartphones

based on Android operating system and

equipped with NFC (Near Field

Communication) function.

■Download on your smartphone the

Hoover Wizard App.

The Hoover Wizard App is available

for devices running both Android

and iOS, both for tablets and for

smartphones. However, you can

interact with the machine and take

advantage of the potential offered

by One Touch only with Android

smartphones equipped with NFC

technology, according to following

functional scheme:

FUNCTIONS

The main functions available using the App

are:

■Voice Coach – A guide to help you

choose the ideal cycle with only three

voice inputs (dishes, load level, stain

level).

■Programmes – To select and launch

new additional washing programmes.

■Clever Care – Advanced settings, Water

Hardness, "Clever Check-up",

Filter-Clean and a troubleshooting

guide.

■Reports – Washing statistics and tips for

a more efficient use of your machine.

Get all the details of the One Touch

functions, browsing the App in

DEMO mode or go to:

www.hooveronetouch.com

HOW TO USE ONE TOUCH

FIRST TIME - Machine registration

■Enter the "Settings" menu of your

Android smartphone and activate the

NFC function inside the "Wireless &

Networks" menu.

Depending on the smartphone

model and its Android OS version,

the process of the NFC activation

may be different. Refer to the

smartphone manual for more

details.

■Switch the appliance on, then enable the

One Touch mode by selecting the

programme "P3", then pressing the

“SUPER ECO” button.

■Open the App, create the user profile

and register the appliance following the

instructions on the phone display or the

"Quick Guide" attached on the

machine.

More information, F.A.Q. and the

video for an easy registration are

available on:

www.hooveronetouch.com/how-to

Android smartphone

with NFC technology

Android smartphone

without NFC technology

Android Tablet

Apple iPhone

Apple iPad

Interaction with the

machine + contents

Contents only

NEXT TIME – Regular usage

■Every time you want to manage the

machine through the App, first you have

to enable the One Touch mode by

switching the appliance on, then selecting

the programme "P3", then pressing the

“SUPER ECO” button.

■Make sure you have unlocked your

phone (from stand-by mode) and you

have activated the NFC function; then,

follow the steps mentioned earlier.

■If you want to start a washing cycle, load

the dishes and the detergent.

■Select the desired function in the App

(e.g.: starting a programme, the

"Clever Check-up" cycle, update

statistics, etc…).

■Follow the instructions on the phone

display, KEEPING IT ON the OneTouch

logo on the machine dashboard, when

requested to do so by the App.

■Close the door of the appliance.

NOTES:

Place your smartphone so that the

NFC antenna on its back matches

the position of the One Touch logo

on the appliance (as illustred below).

If you do not know the position of

your NFC antenna, slightly move the

smartphone in a circular motion

over the One Touch logo until the

App confirms the connection. In

order for the data transfer to be

successful, it is essential TO KEEP

THE SMARTPHONE ON THE

DASHBOARD DURING THESE THE

FEW SECONDS OF THE PROCEDURE;

a message on the device will inform

about the correct outcome of the

operation and advise you when it is

possible to move the smartphone

away.

Thick cases or metallic stickers on

your smartphone could affect or

prevent the transmission of data

between machine and telephone. If

necessary, remove them.

The replacement of some components

of the smartphone (e.g. back cover,

battery, etc...) with non-original

ones, could result in the NFC

antenna removal, preventing the full

use of the App.

The management and the control of

the machine via App is only possible

"by proximity": it is therefore

not possible to perform remote

operations (e.g.: from another room;

outside of the house).

Intensive

Universal

Eco

Rapid 29’

Pre-wash

Once a day - for heavily soiled pans and any

other items that have been left all day for

washing.

Once a day - for normal soiled pans and any

other items that have been left all day for

washing.

Programme for normally soiled tableware (the

most efficient in terms of its combined energy

and water consumption for that type of

tableware).

Programme standardised to EN 50242.

Quick wash for dishes which are to be

washed immediately after the meal. Wash

load of 6 persons.

Short cold pre-wash for items that are stored

in the dishwasher until you are ready to wash

a full load.

Activation of One Touch mode, to enable the

interaction between the appliance and the

Hoover Wizard App. Before the first use with

the App, this position will be occupied by

Intensive program.

Wash with prewash

For wash programmes with prewash, it is advisable to add a second dose of detergent (max.

10 g) directly in the machine.

Description

PROGRAMME GUIDE

Programme

•••••••

75°C

130

••••

••

••••

45°C

190

••

•••

50°C

••

•N/A

•••N/A

•

••••

60°C

120

••

YES

Check list

Avarage

duration

in minutes

Special function

buttons

available

Detergent for soaking

(Prewash)

Detergent for washing

Clean filter

Check rinse aid

dispenser

Check salt container

Hot pre-wash

Cold pre-wash

Main wash

First cold rinse

Second cold rinse

Hot rinse with rinse aid

With cold water (15°C)

-Tolerance ± 10%-

"DELAY START" button

“SUPER ECO” button

Programme contents

N/A= OPTION NOT AVAILABLE

* The water softener unit is set in the

factory at level 3, as this is suitable for

the majority of users.

According to the degree of hardness of

your water, regulate the softener unit in the

following way:

IMPORTANT

The dishwasher must ALWAYS be

off before start of this procedure.

1. Hold down the "PROGRAMME

SELECTION" button and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME SELECTION"

button pressed for at least 5seconds,

UNTIL an audible signal sounds. Some

"PROGRAMME SELECTION" indicator

lights will come on to indicate the

current water softener setting level.

3. Press the same button again to select

the required water softener level: each

time the button is pressed, one indicator

light will come on (the water softener

level is indicated by the number of lights

on). For level 0 all lights will be off.

4. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

WARNING!

If any problem occurs, turn the

dishwasher off by pressing the

"ON/OFF" button and start the

procedure again from the beginning

(STEP 1).

WATER SOFTENER UNIT

Depending on the source of the supply,

water contains varying amounts of limestone

and minerals which are deposited on the

dishes leaving whitish stains and marks.

The higher the level of these minerals

present in the water, the harder the water is.

The dishwasher is fitted with a water

softener unit which, through the use of

special regenerating salt, supplies

softened water for washing the dishes.

The degree of hardness of your water can

be obtained from your water supply

company.

Regulating the water softener

The softener unit can treat water with a

hardness of up to 90°fH (French grading)

or 50°dH (German grading) through 6

different settings.

The table below lists different degrees of

water hardness with the corresponding

setting for the softener unit.

Level

ºfH

(French

grading)

ºdH

(German

grading)

YES

No indicator

lights

Indicator light

Indicator lights

1,2

Indicator lights

1,2,3

Indicator lights

1,2,3,4

Indicator lights

1,2,3,4,5

flashing

Water

hardness

Water

softener

setting

Use of

regenerating

salt

0-5

6-15

16-30

31-45

46-60

61-90

0-3

4-9

10-16

17-25

26-33

34-50

IDENTIFYING MINOR FAULTS

Should the dishwasher fail to operate, before contacting the Service Centre, make

the following checks:

FAULT CAUSE REMEDY

1 - Machine completely dead

2 - Machine does not

draw water

3 - Machine does not

discharge water

4 - Machine discharges

water continuously

5 - Spray arms are not heard

to rotate

6 - On electronic appliances

without a display: one or

more indicator lights

flashing quickly.

Plug is not connected to wall

socket

O/I button has not been pressed

Door is open

No electricity

See causes for no. 1

Water tap is turned off

Programme selector is not at

correct position

The inlet hose is bent

The inlet hose filter is not

correctly connected

Filter is dirty

Outlet hose is kinked

The outlet hose extension is

not correctly connected

The outlet connection on the

wall is pointing downwards not

upwards

Position of outlet hose is too

low

Excessive amount of detergent

Item prevents arms from rotating

Plate and cup filter very dirty

Water inlet tap turned off

Connect electric plug

Press button

Close door

Check the fuse in the plug and

the electricity supply

Check

Turn water tap on

Turn programme selector to

correct position

Eliminate the bends in the hose

Clean the filter at the end of the

hose

Clean filter

Straighten outlet hose

Follow the instructions for

connecting the outlet hose

carefully

Call a qualified technician

Lift outlet hose to at least 40 cm

above floor level

Reduce amount of detergent

Use suitable detergent

Check

Clean plate and cup filter

Switch off the appliance.

Turn on the tap.

Re-set the cycle.

N.B.: Should any of the situations occur and should the machine give a bad wash performance,

it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the

deposits which a second wash in the machine would not be able to remove.

If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.

This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee.

This information will make it possible to take more effective action more quickly.

The manufacturers decline any responsibility for any printing mistakes in this instruction booklet.

They also reserve the right to modify their own appliances as necessary without altering the

essential characteristics.

FAULT CAUSE REMEDY

7 - Load of dishes is only

partially washed

8 - Detergent not dispensed

or partially dispensed

9 - Presence of white spots

on dishes

10 -Noise during wash

11 -The dishes are not

completely dry

See causes for no. 5

Bottom of saucepans have not

been washed well

Edge of saucepans have not

been washed well

Spray arms are partially blocked

The dishes have not been

properly loaded

The end of the outlet hose is in

the water

The incorrect amount of

detergent has been measured

out; the detergent is old and hard

The wash programme is not

thorough enough

The lower basket dishes have

not been washed

Cutlery, dishes, pans, etc... stop

the detergent dispenser opening

Water is too hard

The dishes knock against one

another

The revolving arms knock against

the dishes

Inadequate air flow

Rinse aid missing

Check

Burnt on food remains must

be soaked before putting pans

in dishwasher

Reposition saucepans

Remove spray arms by

unscrewing ring nuts clockwise

and wash under running water

Do not place the dishes too

closely together

The end of the outlet hose

must not come into contact

with the outflow water

Increase the measure

according to how dirty the

dishes are and change detergent

Choose a more vigorous

programme

Depress half load button

Position dishes not to obstruct

the dispenser

Check salt and rinse aid level

and regulate amount.

Should the fault persist,

Contact Service Centre

Re-check loading of dishes in

the basket

Again re-check loading

Leave the dishwasher door ajar

at the end of the wash program

to allow the dishes to dry naturally

Fill the rinse aid dispenser

Hoover guarantees all parts of this product for 5 years from

the date of purchase. During that time Hoover will replace or

repair all defective parts free of charge, except for parts

subject to fair wear and tear such as belts. The call out fee and

labour costs are chargeable after the first 12 months. To

qualify for benefits under the guarantee, you must be able to

provide proof of date of purchase and the appliance must

have been installed and used in accordance with the

instructions described in this manual. Consequential losses and

accidental damage to the machine is not covered by the

guarantee.

Hoover cannot be responsible for the results of using this

machine for any purposes other than those described in this

manual.

This guarantee does not effect your statutory or common law

rights.

For service and repairs please call our national number:

Always use genuine Hoover spares, available direct from GIAS

Service:

Hoovercare

To maintain your Hoover product in peak condition you may

wish to take out a Hoovercare policy, which for an annual

payment provides a comprehensive maintenance and repair

scheme. For more information please call 08444 995599.

The Hoovercare scheme is not available in Eire.

The manufacturer declines all responsibility in the event of any

printing mistakes in this booklet. The manufacturer also

reserves the right to make appropriate modifications to its

products without changing the essential characteristics.

GIAS Service - Tel: 08444 995599

Support Service [Eire 0818 200021]

Hoover Spares Service

Tel: 01204 556111

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment

(WEEE).

WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic

components (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and

dispose properly all pollutants, and recover and recycle all materials.

Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow

some basic rules:

- WEEE should not be treated as household waste;

- WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In

many countries, for large WEEE, home collection could be present.

In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of

charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied

equipment.

The manufacturer declines all responsibility in the event of any printing mistakes in this

booklet. The manufacturer also reserves the right to make appropriate modifications to

its products without changing the essential characteristics.

To consult the product fiche, please refer to the manufacturer website.

17.07 - 41904022

08444 995599

HOOVER SERVICE

FOR YOUR LOCAL ENGINEER PLEASE CALL OUR NATIONAL NUMBER

Areas covered by HOOVER SERVICE DEALERS

Also Channel Islands, Scilly Isles, Orkney, Shetlands

See local telephone directory

Hoover policy is one of continuous development and for this reason

we reserve the right to change specifications without prior notice

HOOVER LIMITED DRAGONPARC ABERCANAID MERTHYR TYDFIL MID-GLAMORGAN CF48 1PQ

EIRE

0818 200021

- HDI LO -