Hoover HOP3150B/E User Manual
Displayed below is the user manual for HOP3150B/E by Hoover which is a product in the Ovens category. This manual has pages.
Related Manuals
USER INSTRUCTIONS
OVENS
CANDY HOOVER GROUP S.R.L. • Via Comolli 16 • 20861 Brugherio (MB) Italy
EN 02
Safety Indications
EN 02
• Cleaning and maintenance should not be carried out by unsupervised
children.
• Only use the meat probe recommended for this oven.
• Children under 8 must be kept at a safe distance from the appliance if
not continuously supervised.
• During cooking, moisture may condense inside the oven cavity or on the
glass of the door. This is a normal condition. To reduce this effect, wait 10-
15 minutes after turning on the power before putting food inside the
oven. In any case, the condensation disappears when the oven reaches
the cooking temperature.
• Cook the vegetables in a container with a lid instead of an open tray.
• WARNING: the appliance and accessible parts become hot during use.
Be careful not to touch any hot parts.
•WARNING: the accessible parts can become hot when the oven is in use.
Children must be kept at a safe distance.
•WARNING: ensure that the appliance is switched off before replacing
the bulb, to avoid the possibility of electric shocks.
•WARNING: before initiating the automatic cleaning cycle:
- Clean the oven door;
- Remove all accessories and the sliding rack kit (where present);
- Do not place tea towels
• In ovens with meat probe it is necessary, before making the cleaning
cycle, close the hole with the nut provided. Always close the hole with the
nut when the meat probe is not used.
• Children must not play with the appliance. The appliance can be used by
those aged 8 or over and by those with limited physical, sensorial or
mental capacities, without experience or knowledge of the product, only
if supervised or provided with instruction as to the operation of the
appliance, in a safe way with awareness of the possible risks.
• Do not use rough or abrasive materials or sharp metal scrapers to clean
the oven door glasses, as they can scratch the surface and cause the glass
to shatter.
• Avoid leaving food inside the oven after cooking for more than 15/20
minutes.
- Remove large or coarse food residues from the inside of the oven using a
damp sponge. Do not use detergents;
• The oven must be switched off before removing the removable parts
and, after cleaning, reassemble them according the instructions.
EN 03
• Failure to comply with the above can compromise the safety of the
appliance and invalidate the guarantee.
• Any excess of spilled material should be removed before cleaning.
• During the pyrolytic cleaning process, surfaces can heat up more than
usual, children must therefore be kept at a safe distance.
• Connect a plug to the supply cable that is able to bear the voltage,
current and load indicated on the tag and having the earth contact. The
socket must be suitable for the load indicated on the tag and must be
having the earth contact connected and in operation. The earth
conductor is yellow-green in colour. This operation should be carried out
by a suitably qualified professional. In case of incompatibility between the
socket and the appliance plug, ask a qualified electrician to substitute the
socket with another suitable type. The plug and the socket must be
conformed to the current norms of the installation country. Connection to
the power source can also be made by placing an omnipolar breaker
between the appliance and the power source that can bear the maximum
connected load and that is in line with current legislation. The yellow-
green earth cable should not be interrupted by the breaker. The socket or
omnipolar breaker used for the connection should be easily accessible
when the appliance is installed.
• The appliance must not be installed behind a decorative door in order to
avoid overheating.
The shelf must be inserted completely into the cavity
• WARNING: Do not line the oven walls with aluminum foil or single-use
protection available from stores. Aluminum foil or any other protection, in
direct contact with the hot enamel, risk melting and deteriorating the
enamel of the insides.
• WARNING: Never remove the oven door seal.
• If the power cable is damaged, it must be substituted with a cable or
special bundle available from the manufacturer or by contacting the
customer service department.
• No additional operation/setting is required in order to operate the appliance
at the rated frequencies.
• The disconnection may be achieved by having the plug accessible or by
incorporating a switch in the fixed wiring in accordance with the wiring
rules.
• The type of power cable must be H05V2V2-F.
• When you place the shelf inside, make sure that the stop is directed
upwards and in the back of the cavity.
• Do not use a steam cleaner for cleaning operations.
General Instructions
5
1.1 Safety indications
1.2 Electrical safety
1.3 Recommendations
1.4 Installation
1.5 Waste management
1.6 Declaration of compliance
2.1 Overview
2.2 Accessories
2.3 First use
Product Description
7
3.1 Display description
3.2 Using the end of cooking timer
3.3 Cooking modes
Use of the Oven
8
4.1 General notes on cleaning
4.2 Maintenance
• Removal of the oven window
• Removal and cleaning of the glass
door
• Changing the bulb
4.3 Hydro Easy Clean Function
Oven Cleaning and Maintenance
11
5.1 F.A.Q.
Troubleshooting
13
Summary
EN 04
1. General Instructions
NOTE: the oven functions, properties and accessories cited in this manual will vary, depending on the
model you have purchased.
We thank you for choosing one of our products. For the
best results with your oven, you should read this
manual carefully and retain it for future reference.
Before installing the oven, take note of the serial
number so that you can give it to customer service staff
if any repairs are required. Having removed the oven
from its packaging, check that it has not been damaged
during transportation. If you have doubts, do not use
the oven and refer to a qualified technician for advice.
Keep all of the packaging material (plastic bags,
polystyrene, nails) out of the reach of children. When
the oven is switched on for the first time, strong
smelling smoke can develop, which is caused by the glue on the insulation panels surrounding the oven
heating for the first time. This is absolutely normal and, if it occurs, you should wait for the smoke to
dissipate before putting food in the oven. The manufacturer accepts no responsibility in cases where
the instructions contained in this document are not observed.
1.1 Safety Indications
- do not touch the appliance with wet or damp hands or feet;
- in case of malfunction and/or poor operation, switch off the appliance and do not tamper with it.
Only use the oven for its intended purpose, that is only for the cooking of foods; any other use, for
example as a heat source, is considered improper and therefore dangerous. The manufacturer cannot
be held responsible for any damage resulting from improper, incorrect or unreasonable usage.
- in general the use of adaptors, multiple sockets and extension cables is not recommended;
The use of any electrical appliance implies the observance of some fundamental rules:
- do not pull on the power cable to disconnect the plug from the socket;
1.2 Electrical Safety
ENSURE THAT AN ELECTRICIAN OR QUALIFIED TECHNICIAN MAKES THE ELECTRICAL CONNECTIONS.
The power supply to which the oven is connected must conform with the laws in force in the country of
installation. The manufacturer accepts no responsibility for any damage caused by the failure to observe
these instructions. The oven must be connected to an electrical supply with an earthed wall outlet or a
disconnector with multiple poles, depending on the laws in force in the country of installation. The
electrical supply should be protected with suitable fuses and the cables used must have a transverse
section that can ensure correct supply to the oven.
CONNECTION
The oven is supplied with a power cable that should only be connected to an electrical supply with 220-
240 Vac 50 Hz power between the phases or between the phase and neutral. Before the oven is
connected to the electrical supply, it is important to check:
- power voltage indicated on the gauge;
The grounding wire connected to the oven's earth terminal must be connected to the earth terminal of
the power supply.
WARNING
Before connecting the oven to the power supply, ask a qualified electrician to check the continuity of the
power supply's earth terminal. The manufacturer accepts no responsibility for any accidents or other
problems caused by failure to connect the oven to the earth terminal or by an earth connection that has
defective continuity.
- the setting of the disconnector.
EN 05
1.3 Recommendations
After each use of the oven, a minimum of cleaning will helpkeep the oven perfectly clean.
Do not line the oven walls with aluminium foil or single-use protection available from stores. Aluminium
foil or any other protection, in direct contact with the hot enamel, risks melting and deteriorating the
enamel of the insides. In order to prevent excessive dirtying of your oven and the resulting strong
smokey smells, we recommend not using the oven at very high temperature. It is better to extend the
cooking time and lower the temperature a little. In addition to the accessories supplied with the oven,
we advise you only use dishes and baking moulds resistant to very high temperatures.
1.4 Installation
The oven can be located high in a column or under a worktop. Before fixing, you must ensure good
ventilation in the oven space to allow proper circulation of the fresh air required for cooling and
protecting the internal parts. Make the openings specified on last page according to the type of fitting.
The manufacturers have no obligation to carry this out. If the assistance of the manufacturer is required
to rectify faults arising from incorrect installation, this assistance is not covered by the guarantee. The
installation instructions for professionally qualified personnel must be followed. Incorrect installation
may cause harm or injury to people, animals or belongings. The manufacturer cannot be held
responsible for such harm or injury.
NOTE: as the oven could require maintenance work, it is advisable to keep another wall socket available
so that the oven can be connected to this if it is removed from the space in which it is installed. The
power cable must only be substituted by technical service staff or by technicians with equivalent
qualifications.
1.5 Waste management and environmental protection
- the WEEE should not be treated as domestic waste;
- the WEEE should be taken to dedicated collection areas managed by the town council or a registered
company.
This appliance is labelled in accordance with European Directive 2012/19/EU regarding
electric and electronic appliances (WEEE). The WEEE contain both polluting substances
(that can have a negative effect on the environment) and base elements (that can be
reused). It is important that the WEEE undergo specific treatments to correctly remove and
dispose of the pollutants and recover all the materials. Individuals can play an important
role in ensuring that the WEEE do not become an environmental problem; it is essential to
follow a few basic rules:
In many countries, domestic collections may be available for large WEEEs. When you buy a new
appliance, the old one can be returned to the vendor who must accept it free of charge as a one-off, as
long as the appliance is of an equivalent type and has the same functions as the purchased appliance.
Where possible, avoid pre-heating the oven and always try to fill it. Open the oven door as infrequently
as possible, because heat from the cavity disperses every time it is opened. For a significant energy
saving, switch off the oven between 5 and 10 minutes before the planned end of the cooking time, and
use the residual heat that the oven continues to generate. Keep the seals clean and in order, to avoid any
heat dispersal outside of the cavity. If you have an electric contract with an hourly tariff, the "delayed
cooking" programme makes energy saving more simple, moving the cooking process to start at the
reduced tariff time slot.
SAVING AND RESPECTING THE ENVIRONMENT
1.6 Declaration of compliance
The parts of this appliance that may come into contact with foodstuffs comply with the provisions of EEC
Directive 89/109.
By placing the mark on this product, we are confirming compliance to all relevant European safety,
health and environmental requirements which are applicable in legislation for this product.
EN 06
2. Product Description
2.1 Overview
1. Control panel
2. Shelf positions
(lateral wire grid if included)
3. Metal grill
4. Drip pan
5. Fan (behind the steel plate)
6. Oven door
2.2 Accessories
Drip pan
1
Collects the residues that drip during the cooking
of foods on the grills.
Metal grill
2
Holds baking trays and plates.
EN 07
1
2
3
54
6
2.3 First Use
PRELIMINARY CLEANING
Clean the oven before using for the first time. Wipe over external surfaces with a damp soft cloth. Wash
all accessories and wipe inside the oven with a solution of hot water and washing up liquid. Set the
empty oven to the maximum temperature and leave on for about 1 hour, this will remove any lingering
smells of newness.
EN 08
3. Use of the Oven
3.1 Display description
5. Temperature or clock display
6. LCD display adjustment controls
7. Thermostat selector knob
8. Function selector knob
3. Cooking time
1. Minute minder
2. Clock setting
4. End of cooking
WARNING : the first operation to carry out after the
oven h as be en in stal led o r following the
interruption of power supply (this is recognizable
the display pulsating and showing ) is setting
the correct time. This is achieved as follows.
12:00
•Release all buttons.
•Push the central button.
•Set time with "-" "+" buttons.
ATTENTION: The oven will only operate providing the
clock is set.
MENU
8
3.2 Using the end of cooking timer
This control enables to set the desired cooking time (max. 120 min.) the
oven will automatically switch off at the end of the set time.
The timer will count down from the set time return to the O position and
switch off automatically.
For normal use of oven set the timer to the position.
To set the oven ensure the timer is not on the O position.
EN 09
FUNCTION HOW TO DEACTIVATE WHAT IT DOES WHY IT IS NEEDEDHOW TO USE
KEY LOCK
MINUTE
MINDER
COOKING
TIME
END OF
COOKING
•Child Lock function is
activated by touching Set
(+) for a minimum of 5
s e c o n d s . F r o m t h i s
moment on all other
function are locked and
the display will flash
STOP and preset time
intermittently.
•Child Lock function is
deactivated by touching
touchpad Set (+) again for
a minimum of 5 seconds.
From this moment on all
functions are selectable
again.
•Push the central button
1 times
•Press the buttons "-"
"+"
to set the required time
•Release all the buttons
•When the set time as
e l a p s e d a n a u d i b l e
alarm is activated (this
alarm will stop on its
own, however it can be
stopped immediately by
pressing the button)
SELECT.
•Sounds an alarm at the
end of the set time.
•During the process, the
display shows the
remaining time.
•Allows to use the oven as
a l a r m c l o c k ( c o u l d b e
a c t i v a t e d e i t h e r w i t h
operating the oven or with
out operating the oven)
• Press the buttons "-" or
"+"to set the lenght of
cooking required
• S e t t h e c o o k i n g
function with the oven
function selector
• Push the central button
2 times
• Release all buttons
• To check how long is left
to run press the SELECT
button 2 Times.
• It allows to preset the
cooking time required for
the recipe chosen.
• To alter/change the
preset time press SELECT
and "-" "+" buttons.
•Push any button to
stop the signal. Push the
central button to return
t o t h e c l o c k
function.
•When the time is elapsed
the oven will switch off
automatically.
Should you wish to stop
cooking earlier either turn
the function selector to 0, or
s e t t i m e t o 0 : 0 0
(SELECT and "-" "+" buttons)
•At the time set, the
oven will switch off. To
switch off manually,
turn the oven function
selector to position O.
•Enables you to set the
end of cooking time
•To check the preset
time push the central
button 3 times
•To modify the preset
t i m e p r e s s b u t t o n s
SELECT + "-" "+"
• S e t t h e c o o k i n g
function with the oven
function selector.
•
• P r e s s t h e
buttons "-" "+" to set the
time at which you wish
the oven to switch off
Push the central button
3 t i m e s
•Release the buttons
• C o o k i n g w i l l s t a r t
autom atica lly at 1 1:45
(12:30 minus 45 mins) and
will continue until the pre-
set end-of-cooking-time,
when the oven will switch
itself off automatically.
WARNING.
•At the end of the cooking
set time, the oven will
switch off automatically and
an audible alarm will ring.
•This function is typically
used with “cooking time”
function.
For example if the dish has
to be cooked for 45 minutes
and needs to be ready by
12:30, simply select the
required function, set the
cooking time to 45 minutes
and the end of cooking time
to 12:30.
If the END of cooking is
selected without setting the
length of cooking time, the
oven will start cooking
immediately and it will stop
at the END of cooking time
set.
T °C
default
180
210
210
40
L3
T °C
range
40 ÷ 40
50 ÷ 240
50 ÷ 230
50 ÷ 240
L1 ÷ L5
Function
Dial Function (Depends on the oven model)
LAMP: Turns on the oven light.
GRILL:use the grill with the door closed.
The top heating element is used alone and you can adjust the temperature. Five
minutes preheating is required to get the elements red-hot. Success is guaranteed
for grills, kebabs and gratin dishes. White meats should be put at a distance from the
grill; the cooking time is longer, but the meat will be tastier. You can put red meats
and fish fillets on the shelf with the drip tray underneath. The oven has two grill
positions:
Grill: 2140 W Barbecue: 3340 W
Allow about ten minutes extra when cooking foods at the same time.
FAN COOKING: We recommend you use this method for poultry, pastries, fish
and vegetables. Heat penetrates into the food better and both the cooking and
preheating times are reduced. You can cook different foods at the same time
with or without the same preparation in one or more positions. This cooking
method gives even heat distribution and the smells are not mixed.
DEFROST: When the dial is set to this position. The fan circulates air at room
temperature around the frozen food so that it defrosts in a few minutes
without the protein content of the food being changed or altered.
*Tested in accordance with the CENELEC EN 60350-1 used for definition of energy class.
3.3 Cooking Modes
It prevents food from drying and encourages rising in cakes, bread dough and
other bottom-cooked food.
Place the shelf in the bottom position.
FAN + LOWER ELEMENT: The bottom heating element is used with the fan
circulating the air inside the oven. This method is ideal for juicy fruit flans, tarts,
quiches and pâté.
EN 10
220 50 ÷ 280
CONVENTIONAL COOKING: Both top and bottom heating elements are used.
Preheat the oven for about ten minutes. This method is ideal for all traditional
roasting and baking. For seizing red meats, roast beef, leg of lamb, game, bread,
foil wrapped food (papillotes), flaky pastry. Place the food and its dish on a shelf
in mid position.
*
PIZZA: With this function hot air circulated in the oven to ensure perfect result
for dishes such as pizza or cake.
220 50 ÷ 230
*
Try all your recipes and reduce the amount of dressing you usually use and
experience the lightness of this new function!
The " " function allows you to cook in a healthier way, by reducing the amount of
fat or oil required. Thanks to the use of the grill and fan combined with a pulsating
cycle of air, it will retain the moisture content of the food, grilling the surface and
using a shorter cooking time, without compromising on taste.
ECO
It is particularly suitable for cooking meat, roasted vegetables and omelettes. The
cycle of pulsed air keeps the humidity inside the oven and the moisture content of
the food, preserving the nutritional values and ensuring a rapid uniform cooking
process.
190 50 ÷ 230
300 ml
EN 11
4. Oven cleaning and maintenance
4.1 General notes on cleaning
If dirty, the seal can be cleaned with a slightly damp sponge.
The lifecycle of the appliance can be extended through regular cleaning. Wait for the oven to cool before
carrying out manual cleaning operations. Never use abrasive detergents, steel wool or sharp objects for
cleaning, so as to not irreparably damage the enamelled parts. Use only water, soap or bleach-based
detergents (ammonia).
GLASS PARTS
It is advisable to clean the glass window with absorbent kitchen towel after every use of the oven. To
remove more obstinate stains, you can use a detergent-soaked sponge, well wrung out, and then rinse
with water.
OVEN WINDOW SEAL
ACCESSORIES
Clean accessories with a wet, soapy sponge before rinsing and drying them: avoid using abrasive
detergents.
DRIP PAN
After using the grill, remove the pan from the oven. Pour the hot fat into a container and wash the pan in
hot water, using a sponge and washing-up liquid.
If greasy residues remain, immerse the pan in water and detergent. Alternatively, you can wash the pan
in the dishwasher or use a commercial oven detergent. Never put a dirty pan back into the oven.
REMOVAL OF THE OVEN WINDOW
1. Open the front window.
2. Open the clamps of the hinge housing on the right and left side of the front window by pushing them
downwards.
3. Replace the window by carrying out the procedure in reverse.
4.2 Maintenance
2. Set the oven function to Static ( ) or Bottom ( )heater
Make sure that the appliance is cool before you
touch it. Care must be taken with all hot surfaces
as there is a risk of burns. Use distilled or drinkable
water.
5. After 30 minutes switch off the program and allow the oven to cool down.
3. Set the temperature to the HYDRO EASY CLEAN icon
4. Allow the program to operate for 30 minutes.
6. When the appliance is cool, clean the inner surfaces of the oven with a cloth.
Warning
The HYDRO EASY CLEAN procedure uses steam to help remove remaining fat and food particles from
the oven.
1. Pour 300 ml of water into the HYDRO EASY CLEAN container at the bottom of the oven.
4.3 Hydro Easy Clean Function
LOW-E
1
2
3
1.
2.
3.
4.
5.
6.
7.
On all glass, the indication "Low-E" must be legible and positioned on the left side of the door, close to
the left-hand lateral hinge. In this way, the printed label of the first glass will be inside the door.
1. Open the oven door.
2.3.4. Lock the hinges, remove the screws and remove the upper metal cover by pulling it upwards.
5.6. Remove the glass, carefully extracting it from the oven door (NB: in pyrolytic ovens, also remove
the second and third glass (if present)).
REMOVAL AND CLEANING OF THE GLASS DOOR
7. At the end of cleaning or substitution, reassemble the parts in reverse order.
EN 12
CHANGING THE BULB
2. Undo the glass cover, unscrew the bulb and replace it with a new bulb of the same type.
3. Once the defective bulb is replaced, replace the glass cover.
1. Disconnect the oven from the mains supply.
5.
5.1 FAQ
Troubleshooting
PROBLEM POSSIBLE CAUSE SOLUTION
The oven does not heat up The clock is not set Set the clock
A cooking function and
temperature has not been set
Ensure that the necessary
settings are correct
The oven does not heat up
EN 13
Steam and condensation on
the user interface panel
Clean with a microfiber
cloth the user interface
panel to remove the
condensation layer
No reaction of the touch
user interface
42827061•70gr A5•12.2018•REV.B
The manufacturer will not be responsible for any inaccuracy resulting from printing or transcript errors contained in this brochure. We
reserve the right to carry out modifications to products as required, including the interests of consumption, without prejudice to the
characteristics relating to safety or function.
INSTALLATION
EN
EN
If the furniture is coverage with a bottom at the back part,
provide an opening for the power supply cable.
If the oven does not have a cooling fan, create an opening
460 mm x 15 mm
EN
Opening
560 mm x 45 mm
595 mm
595 mm
546 mm
22 mm
580 mm
560 mm
A
600 mm
560 mm
560 mm
560 mm
Opening
460mm x 15 mm
560 mm x 45 mm
If the mounting of the plinth does not allow air
circulation, to obtain the maximum performance of
the oven it is necessary to create an opening of
500x10mm or the same surface in 5.000 mm2
EN
A
A
560 mm
590 mm
EN