Hotpoint AQC9 BF7 E1 User Manual
Displayed below is the user manual for AQC9 BF7 E1 by Hotpoint which is a product in the Tumble Dryers category. This manual has pages.
Related Manuals
1
1
English
GB
TUMBLE DRYER
AQUALTIS
AQC9 BF7
Instruction booklet
Contents
Installation, 2
Laundry, 3
Warnings, 4
Care and Maintenance, 6
Dryer Description, 8
The Display, 9
Start and Programmes, 10
Troubleshooting, 15
Service, 16
is symbol reminds you to read this
instruction manual.
! Keep this manual at hand for immediate reference whenever
necessary. Always store this manual close to the tumble dryer and
remember to pass it on to any new owners when selling or transferring
the appliance, so they may familiarise with the warnings and
suggestions herein contained.
! Read these instructions carefully: the following pages contain
important information on installation and useful suggestions for
operating the appliance.
www.hotpoint.eu
2
GB
10 mm
15 mm 15 mm
Where to install the tumble dryer
If the dryer is installed below a worktop,
ensure there are 10 mm between the upper
panel of the dryer and
any objects above it,
and 15 mm between
the sides of the machine
and the walls or furniture
units adjacent to it. This
ensures adequate air
circulation.
The appliance must be
installed with the rear
surface placed against a wall.
Ventilation
Make sure that the dryer is installed in a room free of
humidity and with adequate air circulation. The flow of air
around the dryer is essential to allow water to condense
during drying; the dryer will not function properly if it is
placed in an enclosed space or inside a cabinet.
Some condensation may form if the dryer is used in a small
or cold room.
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. If the dryer is stacked onto or
installed next to a washing machine it can share the same
drain. The height of the drain must be less than 3’ (1 m) from
the bottom of the dryer.
Remove existing hose from position shown in picture A and fit
a suitable length of hose and connect as shown in picture B.
The drain tube has to be below 1 m from the bottom of
the Dryer
Make sure that the hose is not squashed or kinked
when the dryer is in its nal location.
1
2
H<1m
1
2
Picture A Picture B
We do not recommend that the dryer is
installed in a cupboard but the dryer must never
be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite
side to that of the dryer door.
Electrical connections
Before plugging the appliance into the socket,
check the following:
check the following: check the following:
Make sure your hands are dry.
The socket must have an earth
connection.
The socket must be able to withstand the
machine’s maximum power output as
indicated on the rating plate.
The power supply voltage must fall within
the values indicated on the data plate.
Do not use extension leads. Do not pull the
power supply cable. Do not use multiple
plug adaptors if the appliance is fitted with a
plug. For appliances with fitted plug, if the
plug is not suitable for you socket outlet,
contact a qualified technician.
The dryer must not be installed outdoors,
even if the space is sheltered.
Once installed, the dryer’s electrical wire
and plug must be within reach.
The power cord must not be bent or
squashed.
If the plug being replaced is a non-rewirable
type, then the cut-off plug must be disposed of
safely. DO NOT leave it where it can be inserted
into a socket and create a shock hazard.
The power must be regularly checked. If
the supply cord is damaged, it must be
replaced by service agent . (see Assistance).
The manufacturer denies any
responsibility should any of these rules
not be followed.
If in doubt about any of the above
consult a quali ed electrician.
Preliminary information
Once the tumble dryer is installed, clean the inside of the
drum before operating it and remove any dirt accumulated
during transportation.
Installation
3
GB
10 mm
15 mm 15 mm
Where to install the tumble dryer
If the dryer is installed below a worktop,
ensure there are 10 mm between the upper
panel of the dryer and
any objects above it,
and 15 mm between
the sides of the machine
and the walls or furniture
units adjacent to it. This
ensures adequate air
circulation.
The appliance must be
installed with the rear
surface placed against a wall.
Ventilation
Make sure that the dryer is installed in a room free of
humidity and with adequate air circulation. The flow of air
around the dryer is essential to allow water to condense
during drying; the dryer will not function properly if it is
placed in an enclosed space or inside a cabinet.
Some condensation may form if the dryer is used in a small
or cold room.
Water drain
If your dryer is installed next to a drain the water can be
plumbed into this drain. This does away with the need to
empty the water container. If the dryer is stacked onto or
installed next to a washing machine it can share the same
drain. The height of the drain must be less than 3’ (1 m) from
the bottom of the dryer.
Remove existing hose from position shown in picture A and fit
a suitable length of hose and connect as shown in picture B.
The drain tube has to be below 1 m from the bottom of
the Dryer
Make sure that the hose is not squashed or kinked
when the dryer is in its nal location.
1
2
H<1m
1
2
Picture A Picture B
We do not recommend that the dryer is
installed in a cupboard but the dryer must never
be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite
side to that of the dryer door.
Electrical connections
Before plugging the appliance into the socket,
check the following:
Make sure your hands are dry.
The socket must have an earth
connection.
The socket must be able to withstand the
machine’s maximum power output as
indicated on the rating plate.
The power supply voltage must fall within
the values indicated on the data plate.
Do not use extension leads. Do not pull the
power supply cable. Do not use multiple
plug adaptors if the appliance is fitted with a
plug. For appliances with fitted plug, if the
plug is not suitable for you socket outlet,
contact a qualified technician.
The dryer must not be installed outdoors,
even if the space is sheltered.
Once installed, the dryer’s electrical wire
and plug must be within reach.
The power cord must not be bent or
squashed.
If the plug being replaced is a non-rewirable
type, then the cut-off plug must be disposed of
safely. DO NOT leave it where it can be inserted
into a socket and create a shock hazard.
The power must be regularly checked. If
the supply cord is damaged, it must be
replaced by service agent . (see Assistance).
The manufacturer denies any
responsibility should any of these rules
not be followed.
If in doubt about any of the above
consult a quali ed electrician.
Preliminary information
Once the tumble dryer is installed, clean the inside of the
drum before operating it and remove any dirt accumulated
during transportation.
Installation
Drying times
Cottons
High heat
1 kg 2 kg 3 kg 4 kg 5 kg 6 kg 7 kg 8 kg 9 kg
Automatic
minutes 30-40 40-55 55-70 70-80 80-90 95-120 120-140 130-160 140-170
Timed 30 or 60 60 or 90 60 or 90 90 or 120 90 or 120 120 or 160 120 or 160 160 160 or 180
Drying times 800-1000 rpm in washing machine
Synthetics
Low heat
1 kg 2 kg 3 kg
Automatic minutes 30-40 40-50 50-70
Timed Dry setting 30 or 60 30 or 60 60 or 90
Drying times on reduced spin in washing machine
Acrylics
Low heat
1 kg 2 kg
Timed Dry setting 30 60
Sorting laundry
• Check the symbols on the care labels of the various
garments to verify whether the garments can be safely
tumble dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
! Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum.
The following values indicate the weight of dry garments:
Natural fibres: maximum kg
Synthetic fibres: maximum kg
! Do not overload the dryer as this may result is reduced
drying performance.
Care labels
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are
the most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
Drying times
Drying times are approximate and may vary depending on
the following:
• Amount of water retained by items after the spin cycle:
towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different textu-
re and thickness may have different drying times.
• Amount of laundry: single items and small loads may
take longer to dry.
• Drying: if items are to be ironed, they can be removed
from the dryer while still slightly damp. Items that require
complete drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature
of the room, the longer it will take for the dryer to dry
clothing.
• Bulk: certain bulky items require special care during the
drying process. We suggest removing these items and
replacing them in the dryer once they have been sha-
ken out: repeat this procedure several times during the
course of the drying cycle.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep
them soft and fluffy.
The drying times provided refer to the automatic Cupboard
dry programmes.
The Timed drying settings are also indicated to enable you
to select the most suitable timed option.
The weight refers to dry items.
Laundry
9
3
4
GB
! This appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons
and must be followed carefully.
General safety
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
• After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that
children do not use it as a toy.
•Children should be supervised to ensure
that they do not play with the dryer.
• Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
at the front of the dryer should never be
obstructed (see Installation).
• Never use the dryer on carpeting where the
pile height would prevent air from entering
the dryer from the base.
• Check to see if the dryer is empty before
loading it.
• The back of the dryer could become
very hot. Never touch it while in use.
• Do not use the dryer unless the filter,
watercontainer and condenser are securely
in place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are
still warm items inside.
• Clean the filter after each use (see
Maintenance).
• Empty the water container after each use
(see Maintenance).
�• Clean the condenser unit at regular intervals
(see Maintenance).
�• Do not allow lint to collect around the
dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire in your
tumble dryer, the following should
be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed
and been through the spin cycle. It is a fire
hazard to dry items that HAVE NOT been
washed with water.
�• Do not dry garments that have been
treated with chemical products.
• Do not tumble dry items that have
been spotted or soaked with vegetable
or cooking oils, this constitutes a fire
hazard. Oil-affected items can ignite
spontaneously,especially when exposed
to heat sources such as a tumble dryer.
The items become warm, causing
an oxidisation reaction with the oil,
Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent
heat from escaping and so create a fire
hazard.If it is unavoidable that fabrics
containing vegetable or cooking oil or
those that have been contaminated with
hair care products be placed in a tumble
dryer they should first be washed with
extra detergent - this will reduce, but not
eliminate the hazard. They should not
be removed from the dryer and piled or
stacked while hot.
• Do not tumble dry items that have
previously been cleaned in or washed
in, soaked in or soiled with petrol/
gasoline, dry cleaning solvents or other
flammable or explosive substances. Highly
flammable substances commonly used in
domestic environments including cooking
oil, acetone, denatured alcohol, kerosene,
spot removers, turpentine, waxes and wax
removers. Ensure these items have been
washed in hot water with an extra amount
of detergent before being dried in the
tumble dryer.
�• Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
�• Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by the
manufacturer of the fabric softener product.
• Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
�• Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• Remove all objects from pockets such as
lighters and matches.
! WARNING: Never stop the dryer before
the end of the drying cycle unless all
items are quickly removed and spread
out so that the heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water
before tumble drying (if you use a washing
machine first, select a high spin cycle). Doing
this will save time and energy during drying.
• Always dry full loads - you save energy: single
items or small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
Warnings
5
GB
! This appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons
and must be followed carefully.
General safety
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
• After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that
children do not use it as a toy.
•Children should be supervised to ensure
that they do not play with the dryer.
• Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
at the front of the dryer should never be
obstructed (see Installation).
• Never use the dryer on carpeting where the
pile height would prevent air from entering
the dryer from the base.
• Check to see if the dryer is empty before
loading it.
• The back of the dryer could become
very hot. Never touch it while in use.
• Do not use the dryer unless the filter,
watercontainer and condenser are securely
in place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are
still warm items inside.
• Clean the filter after each use (see
Maintenance).
• Empty the water container after each use
(see Maintenance).
�• Clean the condenser unit at regular intervals
(see Maintenance).
�• Do not allow lint to collect around the
dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire in your
tumble dryer, the following should
be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed
and been through the spin cycle. It is a fire
hazard to dry items that HAVE NOT been
washed with water.
�• Do not dry garments that have been
treated with chemical products.
• Do not tumble dry items that have
been spotted or soaked with vegetable
or cooking oils, this constitutes a fire
hazard. Oil-affected items can ignite
spontaneously,especially when exposed
to heat sources such as a tumble dryer.
The items become warm, causing
an oxidisation reaction with the oil,
Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent
heat from escaping and so create a fire
hazard.If it is unavoidable that fabrics
containing vegetable or cooking oil or
those that have been contaminated with
hair care products be placed in a tumble
dryer they should first be washed with
extra detergent - this will reduce, but not
eliminate the hazard. They should not
be removed from the dryer and piled or
stacked while hot.
• Do not tumble dry items that have
previously been cleaned in or washed
in, soaked in or soiled with petrol/
gasoline, dry cleaning solvents or other
flammable or explosive substances. Highly
flammable substances commonly used in
domestic environments including cooking
oil, acetone, denatured alcohol, kerosene,
spot removers, turpentine, waxes and wax
removers. Ensure these items have been
washed in hot water with an extra amount
of detergent before being dried in the
tumble dryer.
�• Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
�• Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by the
manufacturer of the fabric softener product.
• Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
�• Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• Remove all objects from pockets such as
lighters and matches.
! WARNING: Never stop the dryer before
the end of the drying cycle unless all
items are quickly removed and spread
out so that the heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water
before tumble drying (if you use a washing
machine first, select a high spin cycle). Doing
this will save time and energy during drying.
• Always dry full loads - you save energy: single
items or small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
Warnings
Maximum load sizes: 9 kg
Power Consumption
O-mode (Po) - Watts 0.17
Left-on mode (Pl) - Watts 0.17
Programmes Kg kWh Minutes
Standard Cotton* 9 5.25 161
Standard Cotton 4.5 2.79 92
Synthetics 3 1.3 80
*This is the reference programme for the energy
label and suitable to dry normal wet cotton laundry.
This is the most ecient programme in terms of
energy consumption for drying wet cotton laundry.
6
GB
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each
cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once
drying is completed, by
rinsing it under running
water or cleaning it
with a vacuum cleaner.
Should the filter become
clogged, the flow of air
inside the dryer will be seriously hampered:
drying times becomes longer and more energy
is consumed. Moreover, the dryer may become
damaged.
The filter is located in
front of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic
handle upwards (see
Picture).
2. Clean the fluff off the filter and replace it
correctly. Ensure that the filter is pushed fully
home.
! Do not use the dryer unless the filter has
been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items
(handkerchiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on
the stainless steel drum surface: it may be caused by a
combination of water and/or cleaning agents such as wash-
softeners. This coloured film does not affect the dryer’s
performance.
Emptying the water container after
each cycle
2
Remove the water container and
empty it into a sink or other
suitable drain outlet, then
replace it correctly.
Always check the water
container and empty it before
starting a new drying cycle.
-Failure to empty the water container may cause
the following:
- The dryer stops heating (thus the load may still be
damp at the end of the drying cycle).
- The “Empty water container” LED activates to
show that the water container is full.
Priming the Water Collection System
When your dryer is new, the Water Container will
not collect Water until the system is primed, this
will take 1 or 2 drying cycles. Once primed it will
collect Water during every cycle.
Cleaning the condenser unit.
• Remove the condenser (see Picture
below) unit regularly (monthly) and clean off
any fluff deposits from the plates by rinsing it
with cold water running on the rear end of the
condenser.
Removing the condenser:
1. Disconnect the dryer from the power
supply and open the
door.
2. Open the
condenser cover (see
Picture below), unlock
the three catches by
turning them 90° anti-
clockwise, then pull on
the grip to remove the
condenser.
3. Clean the surface
of the seals and replace
the unit with the arrows
pointing upwards, while
making sure that the
catches are securely
fixed.
Quick Tips
!Remember to clean your lter and
Condenser unit after each load.
! Remember to empty your water
container after each load.
! Doing this will keep your machine
working at its BEST!
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be
cleaned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and
mechanical parts work safely (see Assistance).
Care and maintenance
Water Contaniner
Condenser
Unit
Condenser Cover
Catches
Filter
Handle
Air Intake
Tap
Rear
Front
Condenser
Unit
2
7
GB
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each
cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once
drying is completed, by
rinsing it under running
water or cleaning it
with a vacuum cleaner.
Should the filter become
clogged, the flow of air
inside the dryer will be seriously hampered:
drying times becomes longer and more energy
is consumed. Moreover, the dryer may become
damaged.
The filter is located in
front of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic
handle upwards (see
Picture).
2. Clean the fluff off the filter and replace it
correctly. Ensure that the filter is pushed fully
home.
! Do not use the dryer unless the filter has
been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items
(handkerchiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on
the stainless steel drum surface: it may be caused by a
combination of water and/or cleaning agents such as wash-
softeners. This coloured film does not affect the dryer’s
performance.
Emptying the water container after
each cycle
2
Remove the water container and
empty it into a sink or other
suitable drain outlet, then
replace it correctly.
Always check the water
container and empty it before
starting a new drying cycle.
-Failure to empty the water container may cause
the following:
- The dryer stops heating (thus the load may still be
damp at the end of the drying cycle).
- The “Empty water container” LED activates to
show that the water container is full.
Priming the Water Collection System
When your dryer is new, the Water Container will
not collect Water until the system is primed, this
will take 1 or 2 drying cycles. Once primed it will
collect Water during every cycle.
Cleaning the condenser unit.
• Remove the condenser (see Picture
below) unit regularly (monthly) and clean off
any fluff deposits from the plates by rinsing it
with cold water running on the rear end of the
condenser.
Removing the condenser:
1. Disconnect the dryer from the power
supply and open the
door.
2. Open the
condenser cover (see
Picture below), unlock
the three catches by
turning them 90° anti-
clockwise, then pull on
the grip to remove the
condenser.
3. Clean the surface
of the seals and replace
the unit with the arrows
pointing upwards, while
making sure that the
catches are securely
fixed.
Quick Tips
!Remember to clean your lter and
Condenser unit after each load.
! Remember to empty your water
container after each load.
! Doing this will keep your machine
working at its BEST!
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be
cleaned with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, fluff or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the filter area, using a
vacuum cleaner every so often.
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and
mechanical parts work safely (see Assistance).
Care and maintenance
Water Contaniner
Condenser
Unit
Condenser Cover
Catches
Filter
Handle
Air Intake
Tap
Rear
Front
Condenser
Unit
2
8
GB
To open door
Dryer Description
Control Panel
e On/Off button/ light , if the dryer is running and this button
is pressed and held for more than 3 seconds the dryer is turned
o. e light signals that your dryer is in use or ready to select a
programme.
e Programmes knob sets the programme: rotate until the
indicator is pointing to the programme you want to select (see
Start and Programmes).
e Option buttons/ lights select available options for your selected
programme. e lights indicate that the option has been selected
(see Start and Programmes).
e Display Panel has three sections: Sensor Dry = Drying level,
Timed dry = Drying time and Time to End / Delay start each with
a corresponding selection button (see The Display).
START/PAUSE button with indicator light : when the
green indicator light ashes slowly, press the button to start the
programme. When the cycle has started, the indicator light is
illuminated in a xed manner. To pause the programme, press
the button again; the indicator light will turn orange and begin to
ash again.
To restart the programme from the point at which it
was interrupted, press the button again (see Start and
Programmes).
The Programme Progress Lights indicate each state of
the programme by turning on as appropriate (see Start and
Programmes).
Note: this light also flashes amber during post care phase.
e Empty Water indicator “h2o” signals that the water container
should be emptied. e light will take a few seconds to go out aer
replacing the empty water container; the dryer must be running for
this to happen (see The Controls).
Note: if the water bottle is full the display shows “h2o” and the
indicator ashes, the heat is turned o and your clothes will not dry.
e Empty Water / Clean Filter Light gives a reminder before
every programme, that its essential to clean the lter and empty the
water container every time the dryer is used (see Maintenance and
Care).
e Clean Condenser Light gives a reminder, that
its essential to clean the condenser at regular intervals (see
Maintenance and Care).
e Child Lock button/light Press and hold this button aer
selecting your programme and any options. is prevents the
programme settings from being changed.
When the light is lit the other buttons and programme knob are
disabled. Hold the button to cancel and the light will go out.
ECO Light - this light is illuminated as you select options that use
less energy (see the controls).
The Features
Pull on handle
Condenser unit
(cover open)
Water
container
Rating
Plate
Condenser
cover handle
(Pull to open)
Filter
Air Intake
Grille
Model
& Serial
Numbers
Option Buttons and Lights
On/Off Button & Light
Display Panel
Child Lock
Button & Light
Start/Pause
Button & Light
Clean
Condenser
Light
Programme
Progress Light
Programme Knob Empty
Water /
Clean Filter
Light
ECO
Light
Sensor Dry
Timed Dry Delay
Timer
9
GB
The Display
The Display has three sections each with its corresponding button.
Sensor Dry
Aer selecting a programme that has a Sensor Dry Option, press and release the button until the required dryness sensing
level is displayed. If the sensing option is not available the display will ash and the buzzer beeps three times.
! Some drying programmes are not compatible with all sensor drying levels.
Dryness levels available
Timed Dry
Aer selecting a Programme that has a Timed Dry Option, press the Timed Button to select a drying time. e display
will reduce the selected time each time you press and release this button (see Start and Programmes). Each press
decreases the set time 180, 160, 120, 90, 60, 30, 20 and then repeats. If the Timed Dry option is not available the display
will ash and the buzzer beeps three times. e selected time remains displayed aer the programme starts and can be
changed during the programme if you wish.
! You can either choose a sensor dry level or a drying time.
Delay Timer
Aer selecting a Programme that has a Delay Start Option a delay start time can be selected.
Each press of the Delay start button advances the delay setting in 1 hour increments from “1h” to “24h” then “OFF”
and then aer ve seconds cancels the delay.
For delays of 10 hours or more the display counts down the time in hours until 10 hours, then the display shows “9:59” and
then counts down in minutes. For delays of 9 hours or less the display shows hours and minutes and then counts down in
minutes for all of the delay.
Aer the Start/Pause Button is pressed the delay time can be changed or cancelled, if you wish.
When the delay period nished the symbol is o and the Time to End is displayed, if you wish.
If you have chosen a timed drying the display during programming will show the drying time only in the timed drying
display in the middle. Aer having pressed start the machine will turn the time display on and visualize the countdown of the
programme time.
Time to End
If the delay icon is o the time displayed is the Time to End of the programme running.
When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.
When an Automatic programme is selected the time displayed is an estimate of the time remaining.
When the programme is selected the display shows the time required to dry a full load. e remaining time is constantly
monitored during the drying cycle and is updated to show the best forecast.
e time to end is displayed in hours and minutes and counts down each minute.
e colon between the hours and minutes display ashes to show that the time is counting down.
e Display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault code
number, the four option lights and the pause light will also ash Orange (see Troubleshooting).
Damp dry: the most delicate level which makes sure that your clothes are not dripping wet.
Aer a hand-wash the perfect level to then hang your clothes if you do not want to tumble dry
them all the way to the end.
Iron Dry: a very delicate drying, It is useful for garments you would like to iron aerwards.
Hanger plus: just the drying status to hang delicate garments up (as curtains).
Hanger Dry: just the drying level to hang the garments up.
Light dry: ideal for delicate clothes to be folded and placed into the cupboard.
Cupboard Dry: the garments are completely dry and are ready to be folded and placed in the
cupboard.
Ready to Wear: used for clothes to be worn straight away once the cycle is completed.
10
GB
Start and Programmes
Choosing a Programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see Laundry).
3. Open the door and make sure the lter is clean and in place and the
water container is empty and in place (see Maintenance).
4. Load the machine and make sure that the items are not in the
way of the door seal. Close the door.
5. If the ON/O light is not lit; press the On/O Button .
6. Select the Programmes selection that corresponds with
fabric being dried by checking the Programmes table (see
Programmes) as well as the indications for each type of fabric
(see Laundry).
7. Where available, choose Sensor Dry or Timed Dry
option pressing and releasing the corresponding button until the
desired level or time is displayed.
! See programmes table, for more details.
8. Set a delay time and other options as necessary (see The
Display).
9. If you wish the buzzer to sound at the end of the programme,
press the Sound button . If you have selected the Crease Care
option, this option is not available.
10. Press the START button to begin. e display will show
the estimated time to end.
Special Programmes
Easy Iron Programme
Easy Iron is a short 10 minute programme (8 minutes of heat followed by a 2 minutes cool tumble period) which us the bres of clothing
that has been le in the same position/location for an extended period of time. e cycle relaxes the bres and makes them easier to iron and
fold.
! Easy Iron is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than maximum capacity. ese numbers refer to dry weight:
Fabric: Max
Cotton and Cotton mix 2.5 kg
Synthetics 2
Denim 2
2. Unload the dryer immediately aer the end of the drying cycle, hang, fold or iron the articles and put them away in the closet. Should this
not be possible, repeat the cycle.
e Easy Iron eect varies from one fabric to the next. It works very well on traditional fabrics like Cotton or Cotton mix, and less well on
acrylic bres and on materials such as Tencel.®
Wool Programme
• is is a programme for tumble dryer safe garments marked with the symbol .
• It can be used for load sizes up to 1 kg (approximately 3 sweaters).
• We recommend that garments are turned inside out before drying.
• is programme will take about 60 minutes, but may take longer depending on the size and density of the load and the spin speed used in your washer.
• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly damp. Allow these to
dry naturally as over-drying could damage garments.
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.
! is program is not suitable for Acrylic garments.
Jeans
• is is a programme for Jeans made from Denim Cotton. Before drying your Jeans turn the front pockets inside out.
• It can be used for load sizes up to 3 kg (approximately 4 pairs).
• It can also be used on other garments made from same material such as jackets.
• e duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try turning the jeans
inside out and running the programme again for a short period.
• Use this cycle only for a 100% cotton load, do not mix dark and light coloured items. Do not use this cycle for garments with embroidery
and accessories (pins,...), turn the pockets insideout
! We do not recommend that you use this programme if your jeans have elastic waist bands or embroidery.
During the drying programme, you can check on your laundry and
take out the items that are dry while the others continue drying.
When you close the door again, press START in order to resume
drying.
11. During the last few minutes of Drying Programmes before
the programme is completed, the nal COOL TUMBLE phase is
entered (fabrics are cooled), this phase should always be allowed to
complete.
12.To let you know that your programme is complete the buzzer
will beep 3 times and the display shows END (Note: if the SOUND
option was selected the buzzer beeps 3 times every 30 seconds for 5
minutes).
Open the door, take your laundry out, clean the lter and replace it.
Empty the water container and replace it (see Maintenance).
If the Crease Care option has been selected and you do not take
the clothes out immediately the clothes will tumble occasionally for
10 hours or until you open the door.
13. Switch dryer o using the On/O button.
Standby mode
is tumble dryer, in compliance with new energy saving
regulations, is tted with an automatic standby system which is
enabled aer about 30 minutes if no activity is detected. Press the
On-O button to reactivate the dryer.
11
GB
Silk
• is is a programme for drying your Delicate Silk.
• It can be used for load sizes up to 0.5 kg.
• e duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in your washer.
• Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly damp. If this is found
try removing the load and open them out then run the programme again for a short period.
• Only for garments labelled suitable for tumble drying.
Duvet programmes
! Take care with these programme do not dry any items that are damaged which could result in the lling blocking the lter and air path
resulting in a re hazard.
• Must only be used on Single size duvets not suitable for double or king size items.
• Loads dried using this programme are usually ready to use, but may be slightly damp in places. If this is found try removing the load and
open them out and shake then run the programme again for a short period.
• Also suitable for down lled jackets.
Duvet - High Heat option
• is is a programme for drying your Cotton Duvets. With Cotton outer cover and down lling.
• e duration of this programme will depend on the size of the load and the spin speed used in your washer.
• Only for garments labelled suitable for tumble drying.
Duvet - Low Heat option
• is is a programme for drying your Synthetic Duvets, with synthetic lling.
• e duration of this programme will depend on the size of the load and the spin speed used in your washer.
• Only for garments labelled suitable for tumble drying.
Baby Delicate
• is is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille) and for drying your Delicate
Clothes.
• Do not dry items such as bibs and nappy pants with plastic coverings.
• It can be used for load sizes up to 2 kg.
• e duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in your washer.
• Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly damp. If this is found
try turning them inside out and running the programme again for a short period.
Bed & Bath
• is is a programme for Cotton Towels and sheets.
• It can be used for load sizes up to 9 kg.
• e duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
• Loads dried using this programme are usually ready to use; the edges or seams may be slightly damp especially on large items. If this is
found try opening them out and running the programme again for a short period.
Refresh
anks to a cool air ow, oxygen penetrates the bers and transports unpleasant odors such as cigarette smoke, frying, smog out of the
clothes. With this short program, you can easily refresh your garments in just 20 minutes.
! Airing is not a drying programme and should not be used for wet articles of clothing.
• If can be used on any load size up to 9 kg, but is more eective on smaller loads.
20-minute programme that airs your clothes with cool air. Use also to cool warm clothes.
Shirts - Low Heat option
• is is a programme for Shirts made from synthetic materials or a mixture of natural and synthetics materials such as Polyester and Cotton.
• It can be used for load sizes up to 3 kg (approximately 14 shirts).
• e duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in your washer.
• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try turning the shirts
inside out and running the programme again for a short period.
Shirts - High Heat option
• is is a programme for Shirts made from Cotton.
• It can be used for load sizes up to 3 kg (approximately 10 shirts).
• e duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in your washer.
• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try turning the shirts
inside out and running the programme again for a short period.
12
GB
Quick Dry
• Your drying time for small loads is very much reduced with a huge time saving up to 53% on cottons (with High Heat option) and 50% on
synthetics (with Low Heat option).
Load: 1 Kg. Dryness level: only Cupboard Dry
Activewear
• is programme is specic for drying water-repellent fabrics and sports jackets (e.g. Gore-Tex, polyester, nylon). Drying the garment aer a
wash cycle has a benecial eect as it reactivates the garment’s water-repellent treatment.
It can be used for loads of up to 2 kg.e duration of this programme will depend on the size of the load, the dryness setting selected and the
spin speed used in your washer. Dryness level: only Cupboard Dry
Cuddly Toys
• With the cuddly toy cycle user can remove dust easier and wash the cuddly toys more oen because the drying time is very much reduced
compared to drying in the open air. It’s a delicate drying cycle that dries at low temperature and with so mechanical action to maintain at
best the original look and the shine of the hair.
Note: For allergy protection, just freeze for 24hrs your cuddly toys, wash and dry. Repeat every 6 weeks. Before drying remove accessories
such as clothes, collars, or sound boxes and protect plastic eyes (using masking tape).
e programme time will vary dependant on the exact make up of the load. e maximum load should not exceed 2.5 kg and no individual
item should be greater than 600 g.
Heat & Enjoy
• e Heat & Enjoy cycle helps to heat towels & bathrobes for a warm sensation aer a bath or a shower. It is also useful for warming clothes
before dressing during winter.
e cycle heats the clothes up to 37° (the body temperature) and keeps the same temperature for a maximum of 4 hours or until the user stops
the cycle by opening the door.
Load: 3 Kg.
! Note: during this programme a icon rotates in the display until the temperature target is reached at which point the dryness level icon
ashes.
Sensor Drying and Timed Drying
First select a programme (see programmes table).
! For the best performance do not open the door before the cycle has nished.
Programme What it does How to set it Notes / Options available
Sensor
Drying
Always use Sensor Dry if pos-
sible for drying your clothes. It
will guarantee you best drying
results.
The heat setting depends
on the programme (material
option) selected.
1. Press and release the sensor Dry button until
the display shows the desired selection. Each
press advances , , , , , , and
then repeats.
! Some sensing programmes do not have all
7 dryness level options.
2. Select any Options if required.
3. Press the Start Button .
Options available
Sound or Crease care . Delay Start . High Heat
. Extra Care .
Consult suggested drying times (see Laundry).
The last few minutes of these programmes is the cool
tumble phase.
Timed
Drying
(180, 160,
120, 90, 60,
30 or 20
minutes)
Always use timed drying
option if you want to decide
the drying time.
The heat setting depends
on the Programme (material
option) selected.
1. Press and release the Timed Button until the
display shows the required selection. Each
decreases time 180, 160, 120, 90, 60, 30, 20
and then repeats.
• Baby Delicates and Synthetics have a maxi-
mum time of 160.
2. Select any Options if required.
3. Press the Start Button .
Options available
Sound or Crease care . Delay Start . High Heat
.
Consult suggested drying times (see Laundry).
The last few minutes of these programmes is the cool
tumble phase.
Anti Allergy
e programme has the ‘Seal of Approval’ endorsement from ‘Allergy UK’, which reects the eective reduction and elimination of allergens
from the clothes. With this programme, thanks to the achievement of constant temperature for an extended period of time, the eects of the
most common allergens (including House Dust Mite) are neutralized.
Can be used on wet load to dry and treat or on a dry load just to treat your laundry.Maximum load is 9 kg for a wet load and 4 kg for a dry
load.
13
GB
Programme What it does How to set it Notes / Options available
Easy Iron
Brief programme (approxima-
tely 10 minutes) that softens
fibres of clothing that is ready
for ironing.
1. Position the PROGRAMME knob on .
2. Select Alarm Option if required.
3. Press the Start Button .
! This is not a drying programme (see previous page).
Options available
Sound .
Refresh
20 min cool programme to air
your clothes 1. Position the PROGRAMME knob on .
2. Select Alarm Option if required.
3. Press the Start Button .
Sound .
Standard
Cotton**
Dries: your Cotton clothes.
N.B: Max. load 6 kg (with
Low Heat option)
1. Position the PROGRAMME knob on .
2. Choose Sensor Dry or Timed Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound or Crease care . Delay Start . High Heat
Extra Care .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry , Ready to Wear *
Shirts
Dries your shirt.1. Position the PROGRAMME knob on .
2. Choose Sensor Dry or Timed Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound or Crease care . Delay Start . High Heat
.
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .
Jeans
Dries denim clothes. 1. Position the PROGRAMME knob on .
2. Choose Sensor Dry (see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound or Crease care . Delay Start .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry . Ready to Wear *
Synthetics
Dries: your synthetics clothes. 1. Position the PROGRAMME knob on .
2. Choose Sensor Dry or Timed Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound or Crease care . Delay Start .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .
Bed & Bath
Dries your Towels and
bedding.
1. Position the PROGRAMME knob on .
2. Choose Sensor Dry (see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound or Crease care . Delay Start .
Extra Care .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .Ready to Wear *.
(We suggest to use only Cupboard dry).
Duvet
Dries your Duvet. 1. Position the PROGRAMME knob on .
2. Select any Options if required.
3. Press the Start Button .
Sound or Crease care . Delay Start . High Heat .
Wool
Dries: your Woollen clothes. 1. Position the PROGRAMME knob on .
2. Select any Options if required.
3. Press the Start Button .
Sound .
Silk
Dries your silk items. 1. Position the PROGRAMME knob on .
2. Choose Sensor Dry (see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .
(We suggest to use only Cupboard dry).
Baby
Delicate
Dries your baby clothes. 1. Position the PROGRAMME knob on .
2. Choose Sensor Dry or Timed Dry (see
next page).
3. Select any Options if required.
4. Press the Start Button .
Sound or Crease care .Delay Start .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .
(We suggest to use only Cupboard dry).
Anti Allergy
Anti Allergy treatment for your
cotton clothes. 1. Position the PROGRAMME knob on .
2. Select any Options if required.
3. Press the Start Button .
Sound or Crease care . Delay Start .
Quick Dry
Dries your cotton or synthetic
clothes in less time. 1. Position the PROGRAMME knob on .
2. Select any Options if required.
3. Press the Start Button .
Sound or Crease care . Delay Start . High Heat
* just with High Heat option on ** This is the most effi cient program in terms of energy consumption (EU 392/2012). To
reach maximum effi ciency, select the CUPBOARD DRY level and the highest temperature option (Standard/Default starting
confi guration)
Programmes Table
! If the On/O light is not lit; Press the On/O Button and then select programme.
14
GB
The Controls
• Programme knob
! Warning, if aer pressing the start button the programme
knob position is changed, the new position will NOT change the
programme selected.
To change programme press Start/Pause Button to pause the
programme, the light ashes Amber, select new programme and any
option, the light will then ash green. Press the Start/Pause Button
and the new programme will start.
• Option Buttons/ Lights
ese buttons are used to customise the selected programme
to your requirements. Not all options are available for all
programmes (see Start and Programmes). If an option is not
available and you press the button, the buzzer will beep three
times. If the option is available there will be one beep and the
option light next to the button lights to conrm the selection.
• ECO Light
is light is illuminated when you select programme options
that will use less energy than the default setting. Examples are if
you choose an Automatic or sensing programme or use a timed
dry setting less than the default time. is light does not indicate
that the optimum setting for energy use has been selected; it only
shows you that your selected options will use less energy.
• Progress ( Drying, Cool tumble, ) Lights
e Progress lights show you the status of the programme. At each
stage of the programme the corresponding light turns on.
• Delay Timer
e start of some programmes (see Start and Programmes) can
be delayed for up to 24 hours (see e Display).
Ensure the water bottle is emptied and the lter is cleaned before
setting a delayed start.
• Extra Care
e Anti-ageing function for Cottons helps to maintain the
brightness of your laundry for longer thanks to the use of the
right drum rotation (reduced in the last part of cycle) and the
correct drying temperature.
Note: It cannot be used with the “Ready to Wear”, “Cupboard
Dry” and “Light Dry” dryness levels
• Sound
A buzzer sounds at the end of the drying cycle to signal that the
programme has ended and the garments are ready to be removed.
If you have selected the Crease Care option, this option is not
available.
• Crease Care
When a delayed start and this option have been selected the
clothes are tumbled occasionally during the delayed period to
help prevent creases developing.
Aer end of the drying and cool tumble cycles, the clothes are
occasionally tumbled to help prevent creases developing, should
you not be available to remove the load immediately aer the
programme is complete. e light is on during this phase aer
end of the cycle and the start/pause light ashes amber. ashes
amber. If you have selected the Sound option, this option is not
available.
• High Heat
When a drying time is selected, pressing this button sets a high heat
drying and the indicator light above the button lights up.
• Empty Water Clean Filter Light “h2o”
(If you have plumbed your dryer to a drain the light can be
ignored for the water bottle, as there is no need to empty the water
container). When is on (not ashing) it reminds you to empty
the water container. If the water container lls during a programme,
the heater turns o and the dryer does a period of Cool Tumble
then the light ashes and the buzzer sounds. You must empty the
container and restart the dryer or the clothes will not dry. Aer
re-starting the dryer the light will take a few seconds to go out. To
avoid this always empty the water container each time you use the
dryer (see Maintenance).
! Please note that you ALWAYS have to clean the lter even if you
have plumbed your dryer to a drain.
• Door Opening
Opening the door (or pressing the Start/Pause Button) during a
programme will stop the dryer and have the following eects.
Note: e Start/Pause Light ashes Amber during the Post Care
phase of a programme.
• During a delay phase the delay will continue to count
down. e start button must be pressed to resume the delay
programme. One of the delay lights will ash to show the
current delay setting.
• e start button must be pressed to resume the programme.
e progress lights will change to show the current status and
the Start/Pause light will stop ashing and turn green.
• During the post creasecare phase of a drying program, the
Programme will nish. Pressing the Start/Pause button will
restart a new program at the beginning.
• Changing the Programmes knob will select a new
programme and the Start/Pause Light will ash green. You can
use this to select the “Refresh” programme to cool the clothes
if you nd them dry enough. Pressing the start/pause button
to begin new Programme.
• Note
If you have a power cut, switch o the power or remove the plug.
When power is restored, plug in the machine, press and hold the
ON/OFF button until the dryer reactivates, then press Start/Pause
button.
Programme What it does How to set it Notes / Options available
Activewear
Dries your sports clothes. 1. Position the PROGRAMME knob on .
2. Select any Options if required.
3. Press the Start Button .
Sound or Crease care . Delay Start .
Cuddly Toys
Dries your cuddly toy. 1. Position the PROGRAMME knob on .
2. Select any Options if required.
3. Press the Start Button .
Sound . Delay Start .
Heat & Enjoy
Heats your towel & bathrobe. 1. Position the PROGRAMME knob on .
2. Press the Start Button .
-
15
GB
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following troublesho-
oting suggestions.
Possible causes / Solutions:
• The plug is not plugged into the socket, or not making contact.
• There has been a power failure.
• The fuse has blown. Try to plug another appliance into the socket.
• You are using an extension cord. Try to plug the dryer’s power cord directly into the
socket.
• The door is not closed securely.
• The programme has not been set properly (see Start and Programmes).
• The START button has not been pressed (see Start and Programmes).
• You have set a delay time (see Start and Programmes).
• You have pressed the start button; there will be a short delay before the dryer starts.
Wait for drying to begin,do not press the start button again or the dryer will pause
and not begin drying.
• The filter has not been cleaned (see Maintenance).
• The water container needs emptying? The empty water light is flashing and “h2o”
message is displayed? (see Maintenance).
• The condenser needs cleaning (see Maintenance).
• The temperature setting is not ideal for the type of fabric you are drying (see Start and
Programmes, and Laundry).
• The correct drying time has not been selected for this load (see Laundry).
• The air intake grille are obstructed (see Installation and see Maintenance).
• The items are too wet (see Laundry).
• The dryer is overloaded (see Laundry).
• The water container was probably not emptied at the start of the programme. Do
not wait for the empty water signal always check and empty the container before
starting a new drying programme (see Maintenance).
• This is normal the empty water flashes when the container is full. If the light is on but not
flashing its just a reminder to empty the container (see Start and Programmes).
! For safety the dryer has a maximum programme time of 5 hours. If an automatic
programme has not sensed the required final moisture in this time the dryer will
complete the programme and stop. Check the above points and run the programme
again, if the results are still to damp, contact the service centre (see Service).
• If the display shows a Fault, Turn off and remove plug, Clean the Filter and Condenser
(see Maintenance). Then replace plug turn on and start another program. If the
Fault is then displayed contact the service centre (see Service). If any other number
is shown; Note down the number and contact the service centre (see Service).
• The dryer is in ‘Demo’ mode. Press and hold both the On/Off and Start/Pause
buttons for 3 seconds. The display will show “dOn” for 3 seconds and then the
dryer will resume normal operation.
• The time to end is continuously monitored throughout the drying cycle and the time
is adjusted to give the best-estimated time. The displayed time may increase during
the cycle and this is normal.
• This is normal, particularly if the dryer has not been used for a while. If the noise
persists throughout the whole drying cycle then contact the service centre.
• The dryer has gone into standby mode to save power. This occurs if you have left the
dryer on or have had a power cut. It occurs after 30 minutes:
- if you leave the dryer without starting a programme;
- after your drying programme has finished.
Press and hold the ON/OFF button until the dryer reactivates
Problem:
The dryer won’t start.
Drying cycle will not begin.
It is taking a long time to dry.
The Empty water light is flashing
but the dryer has only been running
for a short period.
Empty water light is on and the
water container is not full.
Programme finishes and clothes
damper than expected.
The Display shows a fault code F
followed by one or two numbers,
the option lights and pause light are
flashing.
The display briefly shows “dOn”
every 6 seconds.
Time to End display changes during
drying.
The dryer makes a thumping noi-
se during the first few minutes of
operation.
The lights on the dryer control
panel are off although the dryer is
switched on.
16
GB
Service
This appliance has been designed, constructed and distributed in compliance with the
requirements of European Directives:
- LVD 2014/35/EU, EMC 2014/30/EU and RoHS 2011/65/EU.
Information on recycling and disposal
As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality
components to reduce costs for our customers and to minimise materials wastage.
• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the
appliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.
Disposal of old household appliances
European Directive 2012/19/EC concerning Waste Electrical and Electronic Equipment (WEEE) states that household
appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be
collected separately in order to optimise the cost of re-using and recycling materials comprising the machine, while
preventing potential damage to public health and the environment. The crossed-out wheeled bin symbol appears on all
products to remind owners of the obligations regarding separate waste collection.
Owners should contact their local authorities or appliance dealers for further information concerning the correct disposal of
household appliances.
Before contacting the Technical Assistance Centre:
• Follow the troubleshooting guide to check whether problems
can be solved personally (see Troubleshooting).
• If not, switch the dryer o and contact the Technical Assistance
Centre closest to you.
Spare parts
is dryer is a complex machine. Attempting to repair it
personally or with the aid of an unqualied personnel may put
the safety of people at risk, damage the machine or invalidate the
spare parts guarantee.
Always contact a qualied technician when experiencing
problems with this machine.
Product Guarantee And Repair Information
Guarantee
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the
date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or
materials, we will, at our discretion, either repair or replace the appliance at no cost to you:
This guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions.
- The appliance is used only on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a result of improper installation.
- Replacement of any consumable item or accessory. These include but are not limited to: plugs, cables, batteries, light bulbs, fluorescent
tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-DOMESTIC PREMISES.
Repairs and After Sales
For product help and advice, repairs, spare parts or accessories, we’re here to help.
For local repair engineers - 03448 111 606 ROI - 0818 313 413 UK standard local rate applies ROI local Irish rate applies
For Parts and Accessories visit: parts.hotpoint.co.uk/shop
Please remember to register your appliance at www.hotpointservice.co.uk to activate your 10 year parts guarantee.
Please note, our advisors will require the following information: model number, serial number
This information can be found on the data plate located behind the door.
03/2019
19509892510