Hotpoint LTB 4B019 EU User Manual
Displayed below is the user manual for LTB 4B019 EU by Hotpoint which is a product in the Dishwashers category. This manual has pages.
Related Manuals
English, 1
GB
LTB 4B019
Contents
Product Fiche, 2
Precautions and safety advice, 3-4
General safety
Disposal of old electrical appliances
Saving energy and respecting the environment
Recycling & Disposal Information
Installation, 5-6-7
Positioning and levelling
Connecting the electricity and water supplies
Technical data
Advice regarding the first wash cycle
Description of the appliance, 8
Overall view
Control panel
Loading the racks, 9-10
Lower rack
Cutlery basket
Upper rack
Adjusting the upper rack
Unsuitable crockery
Damage to glass and crockery
Start-up and use, 11
Starting the dishwasher
Measuring out the detergent
Wash cycles, 12
Table of wash cycles
Rinse aid and refined salt, 13
Measuring out the rinse aid
Setting water hardness
Measuring out the refined salt
Care and maintenance, 14
Cutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Troubleshooting, 15
After-Sales Service, 16
Guarantee, 17
Instructions for use
DISHWASHER
2
GB
Product Fiche
Brand HOTPOINT
Model LTB 4B019
Rated capacity in standard place settings (1) 13
Energy efciency class on a scale from A+++ (low consumption) to D (high consumption) A+
Energy consumption per year in kWh (2) 295.0
Energy consumption of the standard cleaning cycle in kWh 1.04
Power consumption of the off-mode in W 0.5
Power consumption of the left-on mode in W 5.0
Water consumption per year in litres (3) 3080.0
Drying efcacy class on a scale from G (low efcacy) to A (high efcacy) A
Programme time for standard cleaning cycle in minutes 190’
The duration of the left-on mode in minutes 10
Noise in dB(A) Re 1pW 49
Built-in model Yes
NOTES
1) The information on the label and che relates to the standard cleaning cycle, this programme is suitable to clean normally soiled
tableware and it is the most efcient programme in terms of combined energy and water consumption. The standard cleaning cycle
corresponds to the Eco cycle.
2) Based on 280 standard cleaning cycles using cold water ll and the consumption of the low power modes. Actual energy
consumption depends on how the appliance is used.
3) Based on 280 standard cleaning cycles. Actual water consumption depends on how the appliance is used.
Product Fiche
GB
3
Precautions and safety advice
The appliance was designed and manufactured in
compliance with current international safety standards.
The following information has been provided for safety
reasons and should therefore be read carefully.
Keep this instruction manual in a safe place for future
reference. If the appliance is sold, given away or
moved, please ensure the manual is kept with the
machine, so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully: it contains
important information regarding the safe installation, use
and maintenance of the appliance.
This appliance is intended to be used in household
and similar applications such as:
- staff kitchen areas in shops, offices and other working
environments;
- farm houses;
- by clients in hotels, motels and other residential type
environments;
- bed and breakfast type environments.
General safety
• Thisapplianceisnotintendedforusebypersons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• Childrenshouldbesupervisedtoensurethatthey
do not play with the appliance.
• Theappliancewasdesignedfordomesticuseinside
the home and is not intended for commercial or
industrial use.
• Theappliancemustbeusedbyadultsonly,towash
domestic crockery according to the instructions in
this manual.
• Theappliancemustnotbeinstalledoutdoors,even
in covered areas. It is extremely dangerous to leave
the machine exposed to rain and storms.
• Donottouchtheappliancewhenbarefoot.
• Whenunpluggingtheappliancealwayspulltheplug
from the mains socket, do not pull on the cable.
• The water supply tap must be shut off and the
plug should be removed from the electrical socket
before cleaning the appliance or carrying out any
maintenance work.
• If the appliance breaks down, do not under any
circumstances touch the internal parts in an attempt
to carry out the repair work yourself.
• Donotleanorsitontheopendooroftheappliance:
this may cause the appliance to overturn.
• Thedoorshouldnotbeleftopenasitmaycreatea
dangerous obstacle.
• Thepackagingmaterialshouldnotbeusedasatoy:
it can become a choking or suffocation hazard.
If your family includes children:
•DONOTallowchildrentoplaywiththeapplianceor
tamper with its controls.
•Keepdetergentsandrinseaidsawayfromchildren.
• Keep children away from the open door of a
dishwasher, there could still be some detergent left
inside.
Disposal of old electrical appliances
The European Directive 2012/19/EU on Waste
ElectricalandElectronicEquipment(WEEE),requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream.Oldappliancesmustbecollectedseparately
in order to optimise the recovery and recycling of
the materials they contain and reduce the impact on
human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance
it must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
Saving energy and respecting the
environment
Saving water and energy
• Onlystartawashcyclewhenthedishwasherisfull.
Whilewaitingforthedishwashertobefilled,prevent
unpleasantodourswiththeSoakcycle(seeWash
Cycles).
• Select a wash cycle that is suited to the type of
crockery and to the soil level of the crockery using
theWashcycletable:
- for dishes with a normal soil level, use the Eco
wash cycle, which guarantees low energy and water
consumption levels.
- if the load is smaller than usual activate the Half
load* option (see Start-up and use).
• If your electricity supply contract gives details of
electricity saving time bands, run wash cycles
during the periods when a lower tariff is applied.
TheDelayedstart*button(seeStart-upanduse)
helps you organise the wash cycles accordingly.
Phosphate-free and chlorine-free detergents
containing enzymes
• Westronglyrecommendthatyouusedetergents
that do not contain phosphates or chlorine, as
these products are harmful to the environment.
4
GB
• Enzymes provide a particularly effective action
at temperatures around 50°C, and as a result
detergents containing enzymes can be used in
conjunction with low-temperature wash cycles in
ordertoachievethesameresultsasanormal65°C
wash cycle.
•To avoid wasting detergent, use the product in
appropriate quantities based on the manufacturer’s
recommendations, the hardness of the water and the
soil level and quantity of the crockery. Even if they
are biodegradable, detergents contain substances
that may alter the balance of nature.
Recycling & Disposal Information
As part of Hotpoint’s continued commitment
to helping the environment, Hotpoint reserves the right
to use quality recycled components to keep down
customer costs and minimise material wastage.
Please dispose of packaging and old appliances
carefully.
To minimise risk of injury to children, remove the door,
plug and cut mains cable off flush with the appliance.
Disposeofthesepartsseparatelytoensurethatthe
appliance can no longer be plugged into a mains
socket and the door cannot be locked shut.
GB
5
If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be
tilted onto its back.
Positioning and levelling
1.Removetheappliancefromallpackagingandcheckthatit
has not been damaged during transportation.
If it has been damaged, contact the retailer and do not proceed
any further with the installation process.
2.Checkthedishwasherbyplacingitsothatitssidesorback
panel are in contact with the adjacent cabinets or even with
the wall. This appliance can also be recessed under a single
worktop*
(see the Assembly instruction sheet).
3. Position the dishwasher on a level and sturdy floor. If the
floor is uneven, the front feet of the appliance may be adjusted
until it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
4*. Adjust the height of the rear foot from the front of the
appliance on the central lower part of the dishwasher, turning
a hexagonal spanner (red color) with an opening of 8 mm in a
clockwise direction to increase the height or in an anticlockwise
direction to decrease the height.
The dishwasher meets the requirements set out by the
regulations in force concerning safety and electrical equipment.
Any technical checks should be conducted exclusively by
a trained and authorised technician: Repairs carried out by
unaithorised persons will invalidate the guarantee, as well as
posing a potential hazard to the user.
The manufacturer declines all responsibility for damage to
persons or property resulting from failure to observe the above
precautions, from tampering with even a single component or
from the use of non-original spare parts.
Electrical Connection
Before inserting the plug into the electrical socket, make sure
that:
• thesocketisearthedandcomplieswithcurrentregulations;
• thesocketcanwithstandthemaximumloadoftheappliance,
which is indicated on the data plate located on the inside of
the door
(seeDescriptionoftheappliance);
• thepowersupplyvoltagefallswithinthevaluesindicatedon
the data plate on the inside of the door;
• thesocketiscompatiblewiththeplugoftheappliance.Ifthis
is not the case, ask an authorised technician to replace the
plug
(see After Sales Service)
; do not use extension cables
or multiple sockets.
Oncetheappliancehasbeeninstalled,thepowersupply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
to prevent all potential hazards.
(See After Sales Service)
This appliance must be earthed.
Fuses:yourappliancecomesfittedwithapluganda13Afuse.If
youneedtoreplacethefuse,onlythoseratedat13AandASTA
approvedtoBS1362shouldbeused.Ifyoulosethefusecover,a
replacement may be obtained from your local authorised Service
CentreorElectricalcompany.Correctreplacementisidentified
by colour coding or the marking on base of plug.
DONOTusetheplugunlessthefusecoverisfitted.
Changing the Plug
Cutoffanddisposeofthesuppliedplugifitdoesnotfityour
socket.
ToavoidashockhazardDONOTinsertthediscarded
plug into a socket anywhere else.
Wiresinthemainsleadarecolouredaccordancewiththe
following code:
Green/Yellow- Earth
Blue - Neutral
Brown - Live
If you change the plug, the colour of the wires in the mains lead
may not correspond with the terminal markings in the plug, which
if not coloured, could be:
EARTH ‘E’or
NEUTRAL ‘N’
LIVE ‘L’
Changing the Mains Lead
A lead can be ordered from Hotpoint Service
UK:08709066066or
RepublicofIreland:1850302220
- If you have damaged the existing lead or require a longer one
a charge will be made. It is strongly advised that this work is
carried out by a qualified electrician.
- If the domestic wiring includes a residual current-operated
circuit breaker, ensure that it conforms to the latest regulations.
The dishwasher must not be connected to the electricity supply
while installation is being carried out.
-Thisapplianceshouldonlybeconnectedtoa230/240VAC
source, via a properly installed earthed socket.
-Usethedishwashersolelyinadomesticenvironment.
-DONOTstandorplaceheavyobjectsonthedoorwhenitis
open, this could damage the door or cause the appliance to
tip forward.
Installation
6
GB
Technical data
Dimensions
width 59,5 cm
height 82 cm
depth 57 cm
Capacity 13 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply voltage See appliance data plate
Total absorbed power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Labelling)
-2012/19/EU Waste Electrical
and Electronic Equipment
(WEEE)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.
Connecting the water supplies
Connectiontothewaterandelectricitysuppliesshould
only be performed by a qualified technician.
The dishwasher should not stand on top of the water
hoses or the electricity supply cable.
Connecting the water inlet hose
The water inlet and outlet hoses and the electricity supply
cable may be positioned towards the right or the left in order
to achieve the best possible installation.
• Toasuitablecoldwaterconnectionpoint:beforeattaching
the hose, run the water until it is perfectly clear so that any
impurities that may be present in the water do not clog the
appliance; after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded connection.
• Toasuitablehotwaterconnectionpoint:yourdishwasher
may be provided with hot water from the mains supply (if
you have a central heating system with radiators) provided
thatitdoesnotexceedatemperatureof60°C.
Screw the hose to the tap as described for connection to
a cold water supply.
If the inlet hose is not long enough, contact a specialist
store or an authorised technician
(see Assistance)
.
The water pressure must be within the values indicated
in the Technical data table
(see Installation).
The hose should not be bent or compressed.
The appliance must be connected to the water supply
network using new hoses.
Donotuseoldhoses.
Ensure that the new hose supplied is connected and the old
hose is disposed of safely.
DONOTovertightenthehoseconnector,handtightis
sufficient.
Ensure the fill hose is not kinked.
Tap connections*: A range of adaptors are available to
suit your tap.
DO NOT connect the dishwasher to a single outlet
instantaneous water heater or an electric heater.
Sink Waste System
Connecttheoutlethose(withoutbendingit)toadrainduct
withaminimumdiameterof32mm.
Theoutlethosemustbeataheightrangingfrom40to80cm
(from15’’to31’’)fromthefloor/surfacewherethedishwasher
rests (A).
• before connecting the drain hose, remove any internal
restrictions; this will prevent a build up of debris which
could cause a blockage
• removeanyrestrictionsfromthewastespigotandensure
that the sealing bung is removed (B).
ItMUSTNOTbeconnectedtoasurfacewaterdrain.
•UntietheendoftheGREYdrainagehosefromtherear
of the appliance.
• If fitting an under sink waste disposal unit, cut out the
membrane, bung or blanking plug.
* Onlyavailableinselectedmodels.
GB
7
Ensure the drain hose is securely
attached, to prevent it coming away
while the machine is in use and
causing a flood.
Fit hose to waste securely using
a “Jubilee” type clip.
Anti-flooding protection*
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply
in the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device New Acqua Stop*, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Undernocircumstanceshouldthewaterinlethosebecutasit
contains live electrical parts.
TheCompanyshallnotbeheldresponsibleforanyincidents
that occur if these regulations are not observed.
Advice regarding the first wash cycle
After the installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack, if any.
Immediately before the first washing, completely fill the salt
dispenserwithwaterandaddonlythenapproximately1kgofsalt
(seechapterentitledRinseaidandrefinedsalt).Thewatermay
overflow: this is normal and is not a cause for concern. Select
thewaterhardnessvalue(seechapterentitledRinseaidand
refined salt). - After the salt has been poured into the machine,
theLOWSALTindicatorlight*switchesoff.
If the salt dispenser is not filled, the water softener and the
heating element may get damaged as a result.
The machine has a buzzer/set of tones
(depending on the
dishwasher model
) to inform the user that a command has
been implemented: power on, cycle end etc.
The symbols/indicator lights/LEDs on the control panel/
display may vary in colour and may have a flashing or fixed
light
(depending on the dishwasher model)
.
The display* provides useful information concerning the
type of wash cycle, wash cycle phase, remaining time,
temperature etc.
* Onlyavailableinselectedmodels.
8
GB
Overall view
Description of the
appliance
*** Onlyincompletelybuilt-inmodels* Onlyavailableinselectedmodels.
The number and type of wash cycles and options may vary depending on the dishwasher model.
1. Upperrack
2. Uppersprayerarm
3. Tip-up dispensers
4. Rackheightadjuster
5. Lower rack
6. Lower sprayer arm
7. Washingfilter
8. Salt dispenser
9. Detergentdispenser,rinse-aiddispenserand
ActiveOxygendevice*
10. Dataplate
11. Controlpanel***
Control panel
Select wash cycle button
ON-OFF/Reset button
and indicator light Wash cycle indicator light
GB
9
Loading the racks
Tips
Before loading the racks, remove all food residues from the
crockery and empty liquids from glasses and containers. No
preventive rinsing is needed under running water.
Arrange the crockery so that it is held in place firmly and does
not tip over; and arrange the containers with the openings facing
downwards and the concave/convex parts placed obliquely,
thus allowing the water to reach every surface and flow freely.
Make sure that the lids, handles, trays and frying pans do not
prevent the sprayer arms from rotating. Place any small items
in the cutlery basket.
Since plastic dishes and non-stick frying pans usually retain more
water drops, their drying will be not so good as that of ceramic
or stainless-steel dishes.
Lightweight items such as plastic containers should be placed
in the upper rack and arranged so that they cannot move.
After loading the appliance, make sure that the sprayer arms
can rotate freely.
Lower rack
The lower rack can hold pans, lids, dishes, salad bowls, cutlery
etc. Large plates and lids should ideally be placed at the sides.
Very soiled dishes and pans should be placed in the lower rack
because in this sector the water sprays are stronger and allow
a higher washing performance.
Several dishwasher models are fitted with tip-up sectors*.
They can be used in a vertical position when arranging dishes
or in a horizontal position (lower) to load pans and salad bowls
easily.
Cutlery basket
The modular basket can slide to optimise the space inside the
lower rack. It is equipped with top grilles for improved cutlery
arrangement.
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards or they
must be positioned horizontally in the tip-up compartments on
the upper rack
Upper rack
Load this rack with delicate and lightweight crockery such as
glasses, cups, saucers and shallow salad bowls.
Several dishwasher models are fitted with tip-up sectors*.
They can be used in a vertical position when arranging tea/
dessert saucers or in a lower position to load bowls and food
containers.
*Onlyavailableinselectedmodelswithdifferentnumbersand
positions.
10
GB
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower position.
The height of the upper rack should be adjusted WHEN THE
RACK IS EMPTY.
NEVER raise or lower the rack on one side only.
If the rack is equipped with a Lift-Up device*
(see figure)
, lift
it up by holding its sides. To restore the lower position, press
the levers (A) at the sides of the rack and follow the rack down.
Unsuitable crockery
• Woodencrockeryandcutlery.
• Delicatedecoratedglasses,artistichandicraftandantique
crockery. Their decorations are not resistant.
• Parts in synthetic material which do not withstand high
temperatures.
• Copperandtincrockery.
• Crockerysoiledwithash,wax,lubricatinggreaseorink.
Thecoloursofglassdecorationsandaluminium/silverpiecescan
change and fade during the washing process. Some types of
glass (e.g. crystal objects) can become opaque after a number
of wash cycles too.
Damage to glass and crockery
Causedby:
• Typeofglassandglassproductionprocess.
• Chemicalcompositionofdetergent.
• Watertemperatureofrinsecycle.
Tips:
• Only use glasses and porcelain guaranteed by the
manufacturer as dishwasher safe.
• Useadelicatedetergentsuitableforcrockery.
• Collectglassesandcutleryfromthedishwasherassoonas
the wash cycle is over.
The upper rack can be adjusted for height based on requirements:
high position to place bulky crockery in the lower rack and low
positiontomakethemostofthetip-upcompartments/sectors
by creating more space upwards.
Tip-up compartments with adjustable position
The side tip-up compartments can be positioned at three
different heights to optimize the arrangement of crockery inside
the rack.
Wineglassescanbeplacedsafelyinthetip-upcompartments
by inserting the stem of each glass into the corresponding slots.
Cutlery tray*
Some dishwasher models are fitted with a sliding tray which
can be used to hold serving utensils or small cups. For optimum
washing performance avoid positioning bulky crockery directly
below the tray. The cutlery tray can be removed
(see Figure).
Before loading the tray, make sure the supports are properly
coupled to the upper rack
(see Figure).
*Onlyavailableinselectedmodels.
GB
11
Start-up and use
Measuring out the detergent
A good wash result also depends on the correct amount of
detergent being used. Exceeding the stated amount does not
result in a more effective wash and increases environmental
pollution.
Based on how soiled the items are, the amount can
be adjusted to individual cases using powder or liquid
detergent.
In the case of normally soiled items, use approximately either
35 gr (powder detergent) or 35 ml (liquid detergent). If tablets
are used, one tablet will be enough.
If the crockery is only lightly soiled or it has been rinsed
with water before being placed in the dishwasher, reduce
the amount of detergent considerably.
For good washing results also follow the instructions shown
on the detergent box. For further questions please ask the
detergent producers' Advice Offices.
If the detergent dispenser is still closed, use the closing
device “A” to open it.
Introduce the detergent into the dry dispenser “B” only.
Place the amount of detergent for pre-washing directly
inside the tub.
1.WhenmeasuringoutthedetergentrefertotheTableofwash
cyclestoaddtheproperquantity.CompartmentB comprises
a level showing the maximum quantity of liquid or powder
detergent that can be added to each cycle.
2.Removedetergentresiduesfromtheedgesofthedispenser
and close the cover until it clicks.
3.Closethelidofthedetergentdispenserbypullingitupuntil
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the wash cycle.
If all-in-one detergents are used, we recommend using the TABS
option, because it adjusts the cycle so that the best washing
and drying results are always achieved.
Only use detergent which has been specifically designed
for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam residue
remaining in the machine after the cycle has ended.
The use of tablets is only recommended for models which
offer the MULTI-FUNCTIONAL TABLETS option.
To achieve the best results from each washing and drying
cycle, powder detergent, rinse-aid liquid and salt should
be used.
*Onlyavailableinselectedmodels.
Starting the dishwasher
1.Turnthewatertapon.
2.OpenthedoorandpresstheON/OFFbutton.
3. Measure out the detergent.
(see adjacent information).
4. Load the racks (
see Loading the racks
).
5. Select the wash cycle in accordance with the type of crockery
and its soil level
(see Table of wash cycles)
by pressing the P
button.
6. Select the wash options*.
(see Special wash cycles and
Options)
.
7.Startthewashcyclebyshuttingthedoor.
8. The end of the wash cycle is indicated by beeps and by the
flashingoftheindicatorlightoftheselectedwashcycle.Open
the door, switch off the appliance by pressing the ON/OFF
button, shut off the water tap and unplug the appliance from
the electricity socket.
9.Waitafewminutesbeforeremovingthecrockeryinorderto
avoidburns.Unloadtheracks,beginningwiththelowerlevel.
- The machine will switch off automatically during
long periods of inactivity in order to minimise
electricity consumption.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce the
amount of detergent used accordingly.
Changing a wash cycle in progress
If a mistake was made in the wash cycle selection process, it
is possible to change the cycle provided that it has only just
begun: open the door, taking care to avoid the escaping steam,
andpressandholdtheON/OFFbutton;themachinewillswitch
off.SwitchthemachinebackonusingtheON/OFFbuttonand
select the new wash cycle and any options desired; start the
cycle by closing the door.
Adding extra crockery
Withoutswitchingoffthemachine,openthedoor,takingcare
to avoid the escaping steam, and place the crockery inside the
dishwasher.Closethedoor:thecyclestartsfromthepointat
which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle or there is a power
cut, the cycle stops. It starts again from the point at which it
was interrupted once the door has been shut or the electricity
supply restored.
12
GB
Wash cycles
Notes:
To reduce consumption, only run the dishwasher when it is full.
Note for Test Laboratories: forinformationoncomparativeENtestingconditions,pleasesendanemailtothefollowingaddress:
ASSISTENZA_EN_LVS@indesitcompany.com
Wash cycle
Wash cycle
which
include
drying
Options
Approximate
duration of wash
cycles
Water
consumption
(l/cycle)
Energy
consumption
(KWh/cycle)
Eco Yes No 03:10’ 11 1,04
Intensive Yes No 02:30’ 16,5 1,65
Normal Yes No 02:00’ 16,0 1,35
Soak No No 00:10’ 4 0,01
Wash-cycledataismeasuredunderlaboratoryconditionsaccordingtoEuropeanStandardEN50242.
Based on the different conditions of use, the wash-cycle duration and data can change.
The number and type of wash cycles and options may vary depending on the dishwasher model.
Instructions on wash-cycle selection and detergent dosage
1.TheECOwashcycleisthestandardcycletowhichtheenergylabeldatarefers.Itcanbeusedtowashcrockerywithanormal
soillevelandisthemostefficientcycleintermsofenergyandwaterconsumptionforthistypeofcrockery.27gr/ml+6gr/ml**–1
Tab (**Quantity of pre-washing detergent)
2.Heavilysoileddishesandpans(nottobeusedfordelicateitems).30gr/ml–1Tab
3.Normallysoiledpansanddishes.27gr/ml+6gr/ml**–1Tab
4.Pre-washwhileawaitingcompletionoftheloadwiththedishesfromthenextmeal.Nodetergent.
Standbyconsumption:Left-onmodeconsumption:5W-Offmodeconsumption:0.5W.
GB
13
Rinse aid and refined salt
Only use products which have been specifically designed
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard.
(Follow the instructions given on the packaging).
If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID indicator lights will stay lit.
Measuring out the rinse aid
Rinseaidmakesiteasierforthecrockerytodry,aswaterrunsoff
the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
• WhentheLOWRINSEAIDindicatorlight* on the control panel
is illuminated, a reserve supply of rinse aid is still available
for1-2cycles;
1.Openthedispenser“D” by pressing and pulling up the tab
on the lid;
2. Carefully introduce the rinse aid as far as the maximum
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
can adjust the quantity of rinse aid.
SwitchthedishwasheronandoffusingtheOn/Offbutton.Press
the Pbutton3times.SwitchonusingtheON/OFFbutton,the
indicator light of the set level flashes
(set to factory level)
Adjust the level of rinse aid supply using the P button; during
this procedure the rinse aid indicator light flashes.
Press the ON/OFF button to save the setting.
IftherinseaidlevelissettoZERO(ECOcycle),norinseaidwill
besupplied.TheLOWRINSEAIDindicatorlightwillnotbelitif
you run out of rinse aid.
Uptomaximum4levelscanbesetbasedonthedishwasher
model.
•Iftherearestreaksonthecrockery,settoalownumber(1-2).
•In case ofdropsofwaterorlimescalemarks,settoa high
number number (3-4).
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt specially designed for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the
water hardness level in your area. This information can be
obtained from your local water supplier.
Switch the dishwasher on and off using the ON/OFF button.
Press and hold the P button for a few seconds until you hear
a beep sound. Switch the dishwasher on using the ON/OFF
button, the indicator light of the set level flashes
(water softener
set to medium level).
Duringthisprocedurethesaltindicatorlightflashes.
Adjust the hardness level using the P button,
(1-2-3-4* see water
hardness table)
up to max. 4* levels.
Press the ON/OFF button to save the setting.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
(°dH=hardnessmeasuredinGermandegrees-°f=hardness
measuredinFrenchdegrees–mmol/l=millimolesperlitre)
Measuring out the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refinedsaltremoveslimescalefromthewater,thusavoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(seeDescription)
and should be filled:
• Whenthegreenfloat* cannot be seen by simply looking at
the cap of the salt dispenser;
• WhentheLOWRINSEAIDindicator
light on the control panel is illuminated *;
1.Removethelowerrackand unscrew
the cap (anticlockwise).
2.Thefirsttimeyoudothis:fillthewater
tank right up to its edge.
3. Position the funnel*
(see figure)
and
fill the salt dispenser up to the edge
(approximately1kg).Itisnormalforalittlewatertoleakout.
4.Removethefunnel*andwipeanysaltresiduesawayfrom
the opening; rinse the cap under running water and then screw
it on, the head facing downwards so as to let the water flow out
of the four slots (star-shaped arrangement) in the lower part of
the cap (cap with green float*).
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
Whennecessary,measureoutthesaltbeforeawashcycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Onlyavailableinselectedmodels.
M
A
X
Water Hardness Table
Average salt container
capacity duration**
level °dH °fH mmol/l months
1 0 - 11 0 - 20 1,1 - 2 5 months
2 12 - 17 21 - 30 2,1 - 3 3 months
3 17 - 34 31 - 60 3,1 - 6 2 months
4*34 - 50 61 - 90 6,1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the use
of salt.
* this setting may cause a slight increase in the duration of the
cycles. ** for 1 wash cycle per day.
14
GB
Shutting off the water and electricity
supplies
• Turnoffthewatertapaftereverywashcycletoavoidleaks.
• Always unplug the appliance when cleaning it and when
performing maintenance work.
Cleaning the dishwasher
• Theexternalsurfacesofthemachineandthecontrolpanel
can be cleaned using a non-abrasive cloth which has been
dampenedwithwater.Donotuseabrasivedetergentsor.
solvents.
• Anymarksontheinsideoftheappliancemayberemoved
using a cloth dampened with water and a little vinegar.
Preventing unpleasant odours
• Alwayskeepthedooroftheapplianceajarinordertoavoid
moisture from forming and being trapped inside the machine.
• Cleanthesealsaroundthedooranddetergentdispensers
regularly using a damp sponge. This will avoid food becoming
trapped in the seals, which is the main cause behind the
formation of unpleasant odours.
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer arms
and block the holes used to spray the water. It is therefore
recommended that you check the arms from time to time and
clean them with a small non-metallic brush.
The two sprayer arms may both be removed.
To remove the upper sprayer
arm, turn the plastic locking ring
in an anti-clockwise direction.
The upper sprayer arm should be
replaced so that the side with the
greater number of holes is facing
upwards.
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free of
impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked
and damage the dishwasher.
Cleanthewaterinletfilteratthetapoutletregularly.
- Turn off the water tap.
-Unscrewtheendofthewaterinlethose,removethefilterand
clean it carefully under running water.
-Re-placethefilterandscrewthewaterhosebackintoposition.
Cleaning the filters
The filter assembly consists of three filters which remove food
residues from the washing water and then recirculate the water.
They should be cleaned if you wish to achieve the best results
in every wash.
Cleanthefiltersregularly.
The dishwasher should not be used without filters or if the
filter is loose.
•Afterseveralwashes,checkthefilterassemblyandifnecessary
clean it thoroughly under running water, using a non-metallic
brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction and
pull it out
(fig.1).
2.RemovethecupfilterB by exerting a slight pressure on the
side flaps
(fig.2);
3. Slide out the stainless-steel plate filter A.
(fig. 3).
4. Inspect the trap and remove any food residues. NEVER
REMOVE the wash-cycle pump protection
(black detail) (fig.4).
After cleaning the filters, re-place the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
Leaving the machine unused for extended
periods
• Disconnecttheappliancefromtheelectricitysupplyandshut
off the water tap.
• Leavethedooroftheapplianceajar.
•Whenyoureturn,runawashcyclewhenthedishwasheris
empty.
Care and maintenance
*Onlyavailableinselectedmodels.
GB
15
Troubleshooting
*Onlyavailableinselectedmodels.
Whenevertheappliancefailstowork,checkforasolutionfromthefollowinglistbeforecallingforAssistance.
Problem: Possible causes / Solutions:
The dishwasher does not start or
cannot be controlled.
• Switch off the appliance by pressing the ON/OFF button, switch it back on
after approximately one minute and reset the program.
• The appliance has not been plugged in properly.
• The dishwasher door has not been shut properly.
The door won’t close. • The lock was released. Strongly push the door until a “clacking” noise is
heard.
No water drains from the
dishwasher.
• The dishwasher cycle has not finished yet.
• The water drain hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
The dishwasher is too noisy.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers (see
Start-up and use.)
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt.)
• The lid on the salt dispenser was not closed properly.
• The rinse aid has been used up or the dosage is too low.
The dishes and glasses are
streaked or have a bluish tinge. • The rinse aid dosage is too high.
The crockery has not been dried
properly.
• A wash cycle without a drying cycle has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid and
salt).
• The rinse aid setting is not suitable.
• The crockery is made from non-stick material or plastic.
The crockery is not clean.
• The racks are overloaded (see Loading the racks.)
• The crockery has not been arranged properly.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles.)
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers (see
Start-up and use.)
• The lid on the rinse aid compartment was not shut correctly.
• The filter is dirty or blocked (see Care and maintenance.)
• The refined salt level is low (see Rinse aid and salt.)
• Switch off the appliance by pressing the ON/OFF button. Turn off the water
tap to avoid any flooding and unplug the appliance.
Make sure the water inlet filter has not become blocked by impurities (see “
Care and maintenance” chapter.)
The dishwasher does not take
any water in - Tap shut-off
alarm.
(beeps are emitted* and all the cycle
indicator lights ash.
The ON/OFF indicator light ashes rapidly
and the 2nd and 3rd wash cycle indicator
lights ash.
• There is no water in the mains supply.
• The water inlet hose is bent (see Installation.)
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken
when the beeps sounded.
• Switch off the machine using the ON/OFF button, turn on the tap and switch
the machine back on after a few seconds by pressing the same button.
Re-program the appliance and restart the wash cycle.
16
GB
After Sales Service
After Sales Service
No one is better placed to care for your Hotpoint
appliance during the course of its working life than
us - the manufacturer.
Essential Contact Information
Hotpoint Service
Wearethelargestserviceteaminthecountryoffering
youaccessto400skilledtelephoneadvisorsand1000
fully qualified engineers on call to ensure you receive fast,
reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
www.hotpointservice.co.uk
Please note: Our advisors will require the following
information:
Model number:
Serial number:
Parts and Accessories
Wesupplyafullrangeofgenuinereplacementpartsas
well as accessory products that protect and hygienically
clean your appliance to keep it looking good and
functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
www.hotpointservice.co.uk
Appliance Registration
We want to give you additional benefits of Hotpoint
ownership. To activate your free 5 year parts guarantee
you must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
www.hotpointservice.co.uk
Indesit Company UK Ltd. Morley Way, Peterborough,
PE29JB
IndesitCompanyUnit49AirwaysIndustrial
Estate,Dublin17
Recycling and Disposal Information
As part of Hotpoint’s continued commitment to helping
the environment, Hotpoint reserves the right to use quality
recycled components to keep down customer costs and
minimise material wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the door,
plug and cut mains cable off flush with the appliance.
Dispose of these parts separately to ensure that the
appliance can no longer be plugged into a mains socket
and the door cannot be locked shut.
GB
17
Guarantee
12 months Parts and Labour Guarantee
Yourappliancehasthebenefitofourmanufacturer’sguarantee,whichcoversthecostofbreakdownrepairsfor
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
This guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
- The appliance is used only on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our property.
- TheapplianceisusedintheUnitedKingdomorRepublicofIreland.
The guarantee does not cover:
- Damageresultingfromtransportation,improperuse,neglectorinterferenceorasaresultofimproper
installation.
- Replacementofanyconsumableitemoraccessory.Theseincludedbutnotlimitedto:plugs,cables,batteries,
light bulbs, fluorescent tubes and starters, covers and filters.
- Replacementofanyremovablepartsmadeofglassorplastic.
THISGUARANTEEWILLNOTAPPLYIFTHEAPPLIANCEHASBEENUSEDINCOMMERCIALORNON-
DOMESTICPREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for our
engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on 08448 24
24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
Weofferaselectionofprotectionplansthatenableyoutofullycoveryourselfagainsttheexpenseofrepairbills
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of
Ireland 01 230 0233).
Free Helpdesk Service
Wehaveadedicatedteamwhocanprovidefreeadviceandassistancewithyourapplianceifyouexperienceany
technicaldifficultieswithinthefirst90daysofownership.SimplycallourHotpointServiceHotlineon 08448 224 224
(Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an engineer to
call.
Guarantee
18
GB
GB
19
20
GB
195113751.01
08/2013jk-XeroxFabriano