Hotpoint NLLCD 1165 WD ADW UK User Manual
Displayed below is the user manual for NLLCD 1165 WD ADW UK by Hotpoint which is a product in the Washing Machines category. This manual has pages.
Related Manuals
GB
Quick Guide
THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.
To receive more comprehensive assistance, register the
appliance on
www.hotpoint.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more
detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
WASH CYCLE TABLE
For all testing institutes:
2) Long cotton cycle: set wash cycle 3 with a temperature of 40°C.
3) Long synthetics cycle: set wash cycle 4 with a temperature of 40°C.
* By selecting the 14 cycle and excluding the spin cycle, the washing machine will drain only.
** The duration of the wash cycles can be checked on the display.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test wash cycle in compliance with regulation 1061/2010:
This cycle is designed for normally soiled cotton loads and is the most ecient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may dier from the indicated value.
1. REMOTE CONTROL button
2. UP / DOWN buttons
3. ON/OFF button
4. ACTIVE CARE button and indicator light
5. START/PAUSE button
6. CONFIRM / KEY LOCK button
7. START DELAY button
8. SPIN button
9. TEMPERATURE button
10. OPTIONS / SETTINGS button
11. STEAM HYGIENE/FAVOURITES button
12. WASH CYCLE SELECTOR KNOB
13. Programme Key
Maximum load 11 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Active
Care
Add
Gar-
ments
()
Detergents and
Additives
Recommended
detergent
Residual damp-
ness %
Energy consump-
tion kWh
Total water l
Wash cycle Temperature Max.
spin speed
(rpm)
Max.
load
(kg)
Duration
(min-
utes)
Pre-
wash Wash Fabric
softener Powder Liquid
Default Range 1 2 3
1 Mixed 40°C - 40°C 1600 11 ** –– – –
2 Eco Cotton (1) 60°C 60°C 1600 11 360 –– 43 1,13 62,5
40°C 1600 11 350 –– 43 1,13 62,5
3 Cotton (2) 40°C - 60°C 1600 11 250 –– 43 1,13 102
4 Synthetics (3) 40°C - 60°C 1200 5,5 175 – 53 0,83 56
5 Delicates 40°C - 40°C 1000 5,5 ** – –– – –
6Wool 40°C - 40°C 800 2,5 ** – – –– – –
7 Anti Allergy 60°C 40°C - 60°C 1600 5,5 ** – – – – –
8 Anti Stain 40° 40°C - 40°C 1000 5,5 ** – – – –
9 White 40°C - 90°C 1600 11 ** – – –
10 Steam Refresh – – – 2 ** – – – – – – – – – –
11 Rapid 30 min 30°C - 30°C 800 5,5 ** – –– – –
12 Specials
• Bed & Bath 60°C - 60°C 1600 11 ** – – – –
• Shirts 40°C - 40°C 600 2 ** – – –– – –
• Business 30°C - 30°C 400 2 ** –– –– – –
• Baby 40°C - 40°C 800 4 ** – – –– – –
• Duvet 30°C - 30°C 1000 3,5 ** –– –– – –
• Silk & Curtains 30°C - 30°C – 1 ** – – –– – –
• Jeans 40°C - 40°C 800 4 ** –– –– – –
• Rapid 15 min 30°C - 30°C 800 4,5 ** – – –– – –
• Fitness 30°C - 30°C 600 4 ** –– –– – –
• Cuddly toys 30°C - 30°C – 1 ** ––– – – – –
13 Favourites: allows for any wash cycle to be stored.
14 Spin & Drain * – – 1600 11 ** – – – – – – – – – –
15 Rinse & Spin – – 1600 11 ** – – – – – – – – –
Required dosage Optional dosage
! Turning the knob to position 12 allows for accessing the menu from which to set additional
washing programmes.
4
1 2 3
56
7
8
911 10
12
13
DISPLAY
! The “Programme key” situated inside the detergent dispenser shows all the
available wash cycles together with a graphic guide on how to use the
individual dispenser compartments.
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Mixed
For washing lightly to normally soiled resilient garments in cotton, linen,
synthetic bres and mixed bres.
Eco Cotton 60°/40°
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
ecient in terms of combined water and electricity consumption.
Cotton
Normally to heavily soiled and robust cottons .
Synthetics
Suitable for washing moderately soiled garments made of synthetic bres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.
Delicates
For washing very delicate garments. It is advisable to turn the garments
inside out before washing them. For best results, use liquid detergent on
delicate garments.
Wool - Woolmark Apparel Care - Green:
The “Wool” wash cycle is approved by the Woolmark Company for
washing wool garments classied as “hand-washable”, provided that the
wash complies with the instructions appearing on the garment’s label
and with those provided by the manufacturer of this washing machine.
(M1135)
Anti Allergy
Suitable for removing major allergens such as pollen, mites and cat or dog hair.
Anti Stain 40°
The programme is suitable to heavily-soiled garments with resistant
colours. It ensures a washing class that is higher than the standard class (A
class). When running the programme, do not mix garments of dierent
colours. We recommend the use of powder detergent. Pre-treatment with
special additives is recommended if there are obstinate stains.
White
For washing normally to heavily soiled towels, underwear, table and bed
linen, etc in resilient cotton and linen. Only when the temperature is
selected at 90°C the cycle is provided with a prewash phase before main
washing phase. In this case it is recommended to add detergent both, in
the prewash and main wash section.
Steam Refresh
The garments will be damp once the cycle is completed, so we recommend
hanging them to dry (2 kg, roughly 3 items). This programme refreshes
garments by removing bad odours and relaxing the bres. Insert dry items
only (that are not dirty) and select programme “Steam Refresh”. Garments
will be a little damp at the end of the cycle and can be worn after a few
minutes. The “Steam Refresh” programme makes ironing easier.
! Do not add softeners or detergents.
! Not recommended for wool or silk garments.
Rapid 30 min
For washing lightly soiled garments quickly. This cycle lasts only 30
minutes, saving time and energy.
Specials
• Bed & Bath
For washing home linen in a single cycle. It optimises the use of fabric
softener and allows for saving time and electricity. We recommend the
use of powder detergent.
• Shirts
Use the special wash cycle to wash shirts in dierent fabrics and
colours to guarantee they receive the best possible care.
• Business
Program for clothes used infrequently or only slightly dirty (do not use
for dry clean garment).
Follow the instructions of the garment’s wash care label.
• Baby
Use the special wash cycle to remove the remove the soiling typically
caused by babies, while removing all traces of detergent from nappies
in order to prevent the delicate skin of babies from suering allergic
reactions. The cycle has been designed to reduce the amount of
bacteria by using a greater quantity of water and optimising the eect
of special disinfecting additives added to the detergent.
• Duvet
Designed for washing eiderdown padded items such as double or
single duvets, cushions and anoraks. It is recommended to load such
padded items in the drum with the edges folded inwards and not to
exceed ¾ of the drum’s volume. For optimal washing, we recommend
using a liquid detergent.
• Silk & Curtains
use special wash cycle to wash all silk garments or curtains. We
recommend the use of special detergent which has been designed to
wash delicate clothes.
For washing curtains, fold and place them in a pillow case or mesh bag.
• Jeans
Turn garments inside-out before washing and use a liquid detergent.
• Rapid 15 min
for washing lightly soiled garments in a short time. Not suitable for
wool, silk and garments to be washed by hand.
• Fitness
Sportswear in knitwear or microbers with a normal degree of dirt and
sweat.
• Cuddly toys
With this program it is possible to remove dust more easily and wash
better cuddle toys.
Spin & Drain
Spins the load then empties the water. For resilient garments. If you
exclude the spin cycle, the machine will drain only
Rinse & Spin
Rinses and then spins. For resilient garments.
DISPLAY
The display is useful when programming the washing machine and
provides plenty of information.
COTTON
--:--
1:40
140040°
By pressing the and buttons, it is possible to select the desired
option and conrm it with the button.
The rst time the machine is switched on, you will be asked to select the
language and the display will automatically display the language selection
menu.
To select the desired language, press the and buttons; to conrm
the selection, press the button.
Area A will display the following: the icon and selected washing programme,
the washing phases and the time remaining to the end of the wash cycle.
Area B will display: the selected options, the energy and water consumption
for the chosen cycle and the button lock symbol.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
DETERGENT DISPENSER DRAWER
compartment 1: Pre-wash detergent
(powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended
that the removable plastic partition A (supplied)
be used for proper dosage.
If powder detergent is used, place the partition
into slot B.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overow the grid.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
1
2
3
A
B
PRODUCT DESCRIPTION
A
E
CD
B
G
F
1.
3.
2.
5.
4.
7.
6.
8.
H
Area C will display the default temperature value on the basis of the set
programme; if the programme does not include the setting of the
temperature, the area will display the “-- °” symbol.
Area D will display the default spin cycle speed on the basis of the set
programme; if the programme does not include the setting of the spin
cycle, the area will display the “--” symbol.
Area E will display the time remaining to the start of the selected
programme if the DELAYED START function was set.
Pressing and holding button F for 3 seconds allows for memorising one or
more preferred wash cycles.
To use the memorised cycles, turn the knob to position 13.
Pressing button G allows for accessing the menu from which to set
additional washing options.
Pressing and holding button G for 3 seconds allows for accessing the
settings menu:
- Language: by pressing the and buttons, the user can select the
desired language and conrm it with the button.
- Sound: by pressing the and buttons, the user can activate or
deactivate the sound of the buttons and conrm it with the button.
- Display brightness: by pressing the and buttons, the user can
select the type of display brightness and conrm it with the button.
- Restoring the factory settings: pressing and holding the button for 2
seconds restores the factory settings.
! During a wash cycle if the user does not interact with the display for 5
minutes, the SCREEN SAVER will activate. To return to the previous window,
simply press any button.
Pressing button H allows for accessing the menu from which to set the
washing machine remotely by external device.
Wi Setup (not applicable in Russia)
To enable the appliance to be remotely controlled, you rst have to
complete successfully the connectivity set up process. This process is
necessary to register your appliance and connect to your home network.
The setup procedure has to be carried out only once. You have to carry it
out again only if you change your router setup properties (network name
and password).
Minimum requirements
Smart device: Android with a 1280x720 (or higher) screen or iOS.
See on App store the App compatibility with Android or iOS versions.
Wireless router: 2.4Ghz WiFi b/g/n.
HOW TO SETUP
To use this feature you need to own: a smart phone or a tablet and a
wireless router connected to internet. Please verify with your smart device
that the signal strength of your home wireless network close to the
appliance is good.
1. Download the Hotpoint Home Net app.
The rst step to get your appliance connected is to download the app for
your mobile device. The Hotpoint Home Net app will be your guide and
walk you through all of the steps listed here. You can download the
Hotpoint Home Net app by visiting either iTunes or Google Play and
follow the instructions from app to create an account, connect and
register your appliance.
The SAID code is used to sync a smart device with your appliance. MAC
Address is displayed for the Wi-Fi module.
The pairing procedure has to carry out again only if you change your
router set up properties (network name or password or data provider).
DISPLAY INDICATORS
Failure: Call Service
Refer to Troubleshooting section
Failure: Water lter clogged
Water cannot be drained; water lter might be blocked
Failure: No water
No or not sucient inlet water.
In the event of any failure, refer to the “Troubleshooting” section.
Key Lock
To activate the control panel lock, press and hold the button for
roughly 3 seconds. When the display visualises “KEY LOCK”, the control
panel is locked (except for the ON/OFF button ). This will prevent
accidental modications to wash cycles, especially when children are at
home. To deactivate the control panel lock, press and hold the
button for approximately 3 seconds.
Locked door indicator
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns o before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is o, the door can be opened.
FIRSTTIME USE
Once the appliance has been installed, and before you use it for the rst
time, run a wash cycle with detergent and no laundry, using the wash
cycle 9 (60°).
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
- Press the ON/OFF button ; “HOTPOINT” will appear on the display.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the wash cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments, as described in the “DETERGENT DISPENSER
DRAWER” section.
- Close the door.
- The machine automatically selects the default temperature and spin
speed set for the selected wash cycle.
- Select the desired wash cycle.
- Select the desired options.
- Press the START/PAUSE button to start the wash cycle; the door will
lock ( symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again. To start
the wash cycle from the point at which it was interrupted, press the
START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the symbol turns on to signal that the door cannot
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE button to pause the cycle. If the
symbol is not lit, the door may be opened. Press the START/PAUSE
button again to continue the cycle.
ADDING GARMENTS
An icon on the display will signal when additional garments can be
introduced into the washing machine, without decreasing the washing
performance. To add garments, rst stop the washing machine by pressing
the START/PAUSE button then open the door and insert them.
Press the START/PAUSE button again to restart the wash cycle from
the point at which it was interrupted.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE button, then select the desired cycle and press
the START/PAUSE button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch o.
AT THE END OF THE WASH CYCLE
This will be indicated by the word “CYCLE END” on the display; when the
symbol switches o, the door may be opened. Open the door, unload the
laundry and switch o the machine. If you do not press ON/OFF button,
the washing machine will switch o automatically after about 15 minutes.
OPTIONS
- If the selected option is incompatible with the set wash cycle or with
another previously selected option, in the menu the name of
incompatible option is represented in grey color and the wording “Not
available” will appear on the display, accompanied by a buzzer, the
option will not be activated.
Steam Hygiene
This option enhances washing performance by generating steam during
the wash cycle to remove any bacteria from the bres, which are treated
at the same time. Place the laundry in the drum, choose a compatible
programme and select option Steam Hygiene.
! The steam generated during the operation of the washing machine may
cause the porthole door to become hazy.
Start Delay
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the desired delay period is reached. When this
option has been activated, the selected values of delay start will appear
on the display. To remove the delayed start setting, press the button until
“--:--” appears on the display.
Active Care
The detergent, premixed with water, creates an unique emulsion able
to better penetrate the bers of the garments, cleaning stains at even
low temperatures, preserving both colors and fabrics. These results are
obtained also due to the multiple dierent specic movements of the
drum which best take care of the garments.
Final Care
The washing machine will perform gentle tumbling through slow
rotations of the drum. Final Care option starts after the cycle ends for a
maximum duration of 6h and you can interrupt at any time by pressing
any button on control panel or turning the knob.
I Rapid / Eco
After pushing the button for the 1st time, option Rapid is selected and the
cycle duration will be reduced.
Otherwise after pushing for the 2nd time, option Eco is selected allowing
more energy saving.
Multi Rinse
By selecting this option, the eciency of the rinse is increased and optimal
detergent removal is guaranteed. It is particularly useful for sensitive skin.
Press the button once, two or three times to select an additional 1, 2 or 3
rinses after the standard cycle rinse and remove all traces of detergent.
Press the button again to go back to the “Normal rinse” rinse type.
Easy Iron
By selecting this function, the wash and the spin cycles will be modied in
order to reduce the formation of creases.
Cold Wash
This option saves energy by not heating the water used to wash your
laundry – an advantage both to the environment and to your energy bill.
Instead, intensied wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid
detergent.
Prewash
Allows you to perform a prewash.
Temperature
Each wash cycle has a pre-dened temperature. To modify the temperature,
press the “
60°
40°
” button. The value will appear on the display.
Spin
Each wash cycle has a pre-dened spin speed. To modify the spin speed,
press the “ ” button. The value will appear on the display.
DESCALE AND CLEAN PROCEDURE
An icon on the display will regularly (roughly every 50 cycles) remind users
that is time to run a maintenance cycle to clean the washing machine and
combat limescale build-up and bad odours.
To delete the descale alert turn the knob or push any button (including ON/
OFF button).
For optimal maintenance we suggest using WPRO Limescale and grease
remover, according to the instructions shown on the package.
The product can be purchased by contacting the technical assistance service
or through the website www.whirlpool.eu.
Whirlpool declines all liability for any damages to the appliance caused by the
use of other cleaning products for washing machines available on the market.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed bres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash
new coloured garments separately). Delicates (small garments – such as
nylon stockings – and items with hooks – such as bras: insert them in a
fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washing machine and
the drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washing machine
o and disconnect it from the mains power. Do not use ammable liquids to
clean the washing machine.
Cutting o the water and electricity supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and during all
maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance can be cleaned using
a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
Remove the dispenser drawer by lifting and pulling it outwards. Wash it
under running water; this procedure should be eected regularly.
Caring for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant odours
from forming.
Cleaning the pump
The washing machine is tted with a self-cleaning pump that does not require
any maintenance. Small items (such as coins or buttons) may sometimes fall
into the protective pre-chamber situated at the base of the pump.
! Make sure that the wash cycle has ended and unplug the appliance.
To access the pre-chamber:
1. remove the covering panel on the front side of the machine by inserting
a screwdriver in the centre and sides of the panel and using it as a lever;
2. place a low and wide container under the water lter in order to collect
the residual water.
3. loosen the drainage pump cover by turning it anti-clockwise: it is
normal for some water to leak out;
4. clean the inside thoroughly;
5. screw the cover back on;
6. put the panel back in place, making sure the hooks slot in place before
pushing the panel onto the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If it is cracked or broken, it
must be replaced: during wash cycles, the high pressure of the water
could suddenly split the hose open.
! Never use hoses that have already been used.
ANTIMICROBIAL SEAL
The seal around the porthole door is made from a special mixture
ensuring antimicrobial protection, thus reducing bacterial proliferation
up to 99.99%.
The seal contains zinc pyrithione, a biocidal substance which reduces the
proliferation of harmful microbes (*) such as batteries and mould prone to
causing stains, unpleasant odours and product deterioration.
(*) According to tests performed by the University of Perugia, Italy
on: Staphylococcus aureus, Escherichia coll, Pseudomonas aeruginosa,
Candida albicans, Aspergillus niger, Penicillium digitatum
In rare cases an allergic reaction may be caused by prolonged contact between seal
and skin.
ACCESSORIES
Contact our Technical Assistance Service to check whether the following
accessories are available for this washing machine model.
Stacking kit
With this accessory you can secure the tumble dryer to the upper part of
your washing machine to save space and facilitate loading and unloading
of the tumble dryer.
TRANSPORT AND HANDLING
Do not lift the washing machine by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the lling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Installation instructions”.
TROUBLESHOOTING
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily
solved using the following list.
Anomalies Possible causes / Solution
The washing machine does
not start.
The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power in the house.
The wash cycle does not start.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The Demo Mode is active (see below how to deactivate).
The washing machine does
not ll with water (“ ”
appears on the display).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The washing machine
continuously loads and
unloads water.
The drain hose is not tted between 65 and 100 cm from the oor.
The free end of the hose is immersed in water.
The wall drainage system is not tted with a breather pipe.
If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the
Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems relating
to back-siphonage, causing the washing machine to ll with water and drain continuously. Special anti-siphon
valves are available in shops and help to prevent this inconvenience.
The washing machines does
not drain and the symbol
(F9E1) on the display.
Clean the pump lter (see Care and maintenance chapter)
The drain hose is bent.
The drainage duct is clogged.
The washing machine
vibrates a lot during the spin
cycle.
Transport bolts have been not removed correctly during installation.
The washing machine is not leveled.
The washing machine is tucked between furniture cabinets and the wall.
The washing machine leaks.
The water inlet hose is not screwed on properly.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The symbol appear and
the display visualises an error
code (e.g.: F1E1, F4...).
Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam.
The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and
machine wash”, or the like).
Too much detergent was used.
“ ” phase icon blinks, “0”
spin speed displayed .
Unbalance of laundry load prevented spin cycle, to protect the washing machine.
If you want to spin the wet laundry, add more laundry items of dierent sizes and start “Spin&Drain” programme.
Avoid small laundry loads consisting of few big, absorbent pieces of laundry / wash dierent sizes of articles in one
load.
Not possible to connect .
Please verify with your smart device that the signal strength of your home wireless network close to the appliance
is good.
Check connection of router to Internet and eventually contact your Internet service provider.
If router is connected to Internet follow app instructions for connect router to appliance.
You can download the SAFETY AND INSTALLATION INSTRUCTIONS, OPERATING MANUAL, TECHNICAL
SHEET and ENERGY DATA by:
• Visiting the website http://docs.hotpoint.eu.
• Using the QR code.
• Alternatively, contact our Technical Assistance Service (the telephone number is indicated in the warranty
booklet). When contacting the Technical Assistance Service, provide the codes shown on the adhesive label applied
to the inside of the door.
xxxxxxxxxxxx
xxxx
Disable the DEMO MODE : The following actions must be carried out in sequence, without breaks. Switch the machine ON and then switch it OFF again. Press
the START/PAUSE button until the buzzer is heard. Switch the machine on again. The “DEMO” indicator ashes and then turns OFF.
11253497