Hotpoint NLLCD 947 WD ADW UK User Manual

Displayed below is the user manual for NLLCD 947 WD ADW UK by Hotpoint which is a product in the Washing Machines category. This manual has pages.

Related Manuals

Hotpoint NLLCD 1165 WD ADW UK Manual

Hotpoint NLLCD 1045 WD AW UK Manual

Hotpoint NLLCD 1044 WD AW UK N Manual

Hotpoint NLLCD 1047 WC AD EU Manual

Hotpoint BI WDHL 7128 UK Manual

Hotpoint BI WDHG 75148 UK N Manual

Whirlpool ARG 9470 A+ Manual

www.hotpoint.eu/register

User Manual

Quick Guide

THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.

To receive more comprehensive assistance, register the

appliance on

www.hotpoint.eu/register

Before using the appliance carefully read the Health and Safety guide.

Before using the machine, it is imperative that the transport bolts are removed. For more

detailed instructions on how to remove them, see the Installation Guide.

CONTROL PANEL

WASH CYCLE TABLE

For all testing institutes:

2) Long cotton cycle: set wash cycle 3 with a temperature of 40°C.

3) Long synthetics cycle: set wash cycle 4 with a temperature of 40°C.

* By selecting the 14 cycle and excluding the spin cycle, the washing machine will drain only.

** The duration of the wash cycles can be checked on the display.

The cycle duration indicated on the display or instruction manual is an estimate based on

standard conditions. The actual duration may vary in relation to several factors, such as

the temperature and pressure of the incoming water, ambient temperature, amount of

detergent, load quantity and type, load balancing and any additional options selected.

1) Test wash cycle in compliance with regulation 1061/2010:

This cycle is designed for normally soiled cotton loads and is the most ecient in terms of

both electricity and water consumption; it should be used for garments washable at 60°C or

at 40°C. The actual washing temperature may dier from the indicated value.

1. REMOTE CONTROL button

2. UP / DOWN buttons

3. ON/OFF button

4. ACTIVE CARE button and indicator light

5. START/PAUSE button

6. CONFIRM / KEY LOCK button

7. START DELAY button

8. SPIN button

9. TEMPERATURE button

10. OPTIONS / SETTINGS button

11. STEAM HYGIENE/FAVOURITES button

12. WASH CYCLE SELECTOR KNOB

13. Programme Key

Maximum load 9 kg

Power input in o mode 0.5 W / in left-on mode 8 W

Active

Care

Add

Gar-

ments

()

Detergents and

Additives

Recommended

detergent

Residual damp-

ness %

Energy consump-

tion kWh

Total water l

Wash cycle Temperature Max.

spin speed

(rpm)

Max.

load

(kg)

Duration

(min-

utes)

Pre-

wash Wash Fabric

softener Powder Liquid

Default Range 1 2 3

1 Mixed 40°C - 40°C 1400 9 **      –– – –

2 Eco Cotton (1) 60°C 60°C 1400 9 290 ––    53 0,7 56,5

40°C 1400 9 290 ––    53 0,7 56,5

3 Cotton (2) 40°C - 60°C 1400 9 235 ––    53 1,24 94

4 Synthetics (3) 40°C - 60°C 1200 4,5 175 –      53 0,54 55

5 Delicates 40°C - 40°C 1000 4,5 **   –  –– – –

6Wool 40°C - 40°C 800 2 ** – –  –– – –

7 Anti Allergy 60°C 40°C - 60°C 1400 5 ** – –    – – –

8 Anti Stain 40° 40°C - 40°C 1000 4,5 **   –    – – –

9 White 40°C - 90°C 1400 9 **        – – –

10 Steam Refresh – – – 2 ** – – – – – – – – – –

11 Rapid 30 min 30°C - 30°C 800 4,5 **   –  –– – –

12 Specials

• Bed & Bath 60°C - 60°C 1400 9 **   –    – – –

• Shirts 40°C - 40°C 600 2 ** – –  –– – –

• Business 30°C - 30°C 400 2 ** ––  –– – –

• Baby 40°C - 40°C 800 4 ** – –  –– – –

• Duvet 30°C - 30°C 1000 3,5 ** ––  –– – –

• Silk & Curtains 30°C - 30°C – 1 ** – –  –– – –

• Jeans 40°C - 40°C 800 4 ** ––  –– – –

• Rapid 15 min 30°C - 30°C 800 4,5 ** – –  –– – –

• Fitness 30°C - 30°C 600 4 ** ––  –– – –

• Cuddly toys 30°C - 30°C – 1 ** ––– – – – –

13 Favourites: allows for any wash cycle to be stored.

14 Spin & Drain * – – 1400 9 ** – – – – – – – – – –

15 Rinse & Spin – – 1400 9 ** – – – – – – – – –

 Required dosage  Optional dosage

! Turning the knob to position 12 allows for accessing the menu from which to set additional

washing programmes.

1 2 3

911 10

DISPLAY

! The “Programme key” situated inside the detergent dispenser shows all the

available wash cycles together with a graphic guide on how to use the

individual dispenser compartments.

WASH CYCLES

Follow the instructions on the symbols of the garment’s wash

care label. The value indicated in the symbol is the maximum

recommended temperature for washing the garment.

Mixed

For washing lightly to normally soiled resilient garments in cotton, linen,

synthetic bres and mixed bres.

Eco Cotton 60°/40°

Suitable for washing moderately soiled cotton garments. At 40°C and

60°C it is the standard cycle for washing cotton garments, and is the most

ecient in terms of combined water and electricity consumption.

Cotton

Normally to heavily soiled and robust cottons .

Synthetics

Suitable for washing moderately soiled garments made of synthetic bres

(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.

Delicates

For washing very delicate garments. It is advisable to turn the garments

inside out before washing them. For best results, use liquid detergent on

delicate garments.

Wool - Woolmark Apparel Care - Green:

The “Wool” wash cycle is approved by the Woolmark Company for

washing wool garments classied as “hand-washable”, provided that the

wash complies with the instructions appearing on the garment’s label

and with those provided by the manufacturer of this washing machine.

(M1127)

Anti Allergy

Suitable for removing major allergens such as pollen, mites and cat or dog hair.

Anti Stain 40°

The programme is suitable to heavily-soiled garments with resistant

colours. It ensures a washing class that is higher than the standard class (A

class). When running the programme, do not mix garments of dierent

colours. We recommend the use of powder detergent. Pre-treatment with

special additives is recommended if there are obstinate stains.

White

For washing normally to heavily soiled towels, underwear, table and bed

linen, etc in resilient cotton and linen. Only when the temperature is

selected at 90°C the cycle is provided with a prewash phase before main

washing phase. In this case it is recommended to add detergent both, in

the prewash and main wash section.

Steam Refresh

The garments will be damp once the cycle is completed, so we recommend

hanging them to dry (2 kg, roughly 3 items). This programme refreshes

garments by removing bad odours and relaxing the bres. Insert dry items

only (that are not dirty) and select programme “Steam Refresh”. Garments

will be a little damp at the end of the cycle and can be worn after a few

minutes. The “Steam Refresh” programme makes ironing easier.

! Do not add softeners or detergents.

! Not recommended for wool or silk garments.

Rapid 30 min

For washing lightly soiled garments quickly. This cycle lasts only 30

minutes, saving time and energy.

Specials

• Bed & Bath

For washing home linen in a single cycle. It optimises the use of fabric

softener and allows for saving time and electricity. We recommend the

use of powder detergent.

• Shirts

Use the special wash cycle to wash shirts in dierent fabrics and

colours to guarantee they receive the best possible care.

• Business

Program for clothes used infrequently or only slightly dirty (do not use

for dry clean garment).

Follow the instructions of the garment’s wash care label.

• Baby

Use the special wash cycle to remove the remove the soiling typically

caused by babies, while removing all traces of detergent from nappies

in order to prevent the delicate skin of babies from suering allergic

reactions. The cycle has been designed to reduce the amount of

bacteria by using a greater quantity of water and optimising the eect

of special disinfecting additives added to the detergent.

• Duvet

Designed for washing eiderdown padded items such as double or

single duvets, cushions and anoraks. It is recommended to load such

padded items in the drum with the edges folded inwards and not to

exceed ¾ of the drum’s volume. For optimal washing, we recommend

using a liquid detergent.

• Silk & Curtains

use special wash cycle to wash all silk garments or curtains. We

recommend the use of special detergent which has been designed to

wash delicate clothes.

For washing curtains, fold and place them in a pillow case or mesh bag.

• Jeans

Turn garments inside-out before washing and use a liquid detergent.

• Rapid 15 min

for washing lightly soiled garments in a short time. Not suitable for

wool, silk and garments to be washed by hand.

• Fitness

Sportswear in knitwear or microbers with a normal degree of dirt and

sweat.

• Cuddly toys

With this program it is possible to remove dust more easily and wash

better cuddle toys.

Spin & Drain

Spins the load then empties the water. For resilient garments. If you

exclude the spin cycle, the machine will drain only

Rinse & Spin

Rinses and then spins. For resilient garments.

DISPLAY

The display is useful when programming the washing machine and

provides plenty of information.

COTTON

--:--

1:40

140040°

By pressing the and buttons, it is possible to select the desired

option and conrm it with the button.

The rst time the machine is switched on, you will be asked to select the

language and the display will automatically display the language selection

menu.

To select the desired language, press the and buttons; to conrm

the selection, press the button.

Area A will display the following: the icon and selected washing programme,

the washing phases and the time remaining to the end of the wash cycle.

Area B will display: the selected options, the energy and water consumption

for the chosen cycle and the button lock symbol.

1. Top

2. Detergent dispenser drawer

3. Control panel

4. Handle

5. Porthole door

6. Drain pump (behind the plinth)

7. Plinth (removable)

8. Adjustable feet (2)

DETERGENT DISPENSER DRAWER

compartment 1: Pre-wash detergent

(powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

If liquid detergent is used, it is recommended

that the removable plastic partition A (supplied)

be used for proper dosage.

If powder detergent is used, place the partition

into slot B.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overow the grid.

! Use powder detergent for white cotton garments, for pre-washing, and

for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

PRODUCT DESCRIPTION

Area C will display the default temperature value on the basis of the set

programme; if the programme does not include the setting of the

temperature, the area will display the “-- °” symbol.

Area D will display the default spin cycle speed on the basis of the set

programme; if the programme does not include the setting of the spin

cycle, the area will display the “--” symbol.

Area E will display the time remaining to the start of the selected

programme if the DELAYED START function was set.

Pressing and holding button F for 3 seconds allows for memorising one or

more preferred wash cycles.

To use the memorised cycles, turn the knob to position 13.

Pressing button G allows for accessing the menu from which to set

additional washing options.

Pressing and holding button G for 3 seconds allows for accessing the

settings menu:

- Language: by pressing the and buttons, the user can select the

desired language and conrm it with the button.

- Sound: by pressing the and buttons, the user can activate or

deactivate the sound of the buttons and conrm it with the button.

- Display brightness: by pressing the and buttons, the user can

select the type of display brightness and conrm it with the button.

- Restoring the factory settings: pressing and holding the button for 2

seconds restores the factory settings.

! During a wash cycle if the user does not interact with the display for 5

minutes, the SCREEN SAVER will activate. To return to the previous window,

simply press any button.

Pressing button H allows for accessing the menu from which to set the

washing machine remotely by external device.

Wi Setup (not applicable in Russia)

To enable the appliance to be remotely controlled, you rst have to

complete successfully the connectivity set up process. This process is

necessary to register your appliance and connect to your home network.

The setup procedure has to be carried out only once. You have to carry it

out again only if you change your router setup properties (network name

and password).

Minimum requirements

Smart device: Android with a 1280x720 (or higher) screen or iOS.

See on App store the App compatibility with Android or iOS versions.

Wireless router: 2.4Ghz WiFi b/g/n.

HOW TO SETUP

To use this feature you need to own: a smart phone or a tablet and a

wireless router connected to internet. Please verify with your smart device

that the signal strength of your home wireless network close to the

appliance is good.

1. Download the Hotpoint Home Net app.

The rst step to get your appliance connected is to download the app for

your mobile device. The Hotpoint Home Net app will be your guide and

walk you through all of the steps listed here. You can download the

Hotpoint Home Net app by visiting either iTunes or Google Play and

follow the instructions from app to create an account, connect and

The SAID code is used to sync a smart device with your appliance. MAC

Address is displayed for the Wi-Fi module.

The pairing procedure has to carry out again only if you change your

router set up properties (network name or password or data provider).

DISPLAY INDICATORS

Failure: Call Service

Refer to Troubleshooting section

Failure: Water lter clogged

Water cannot be drained; water lter might be blocked

Failure: No water

No or not sucient inlet water.

In the event of any failure, refer to the “Troubleshooting” section.

Key Lock

To activate the control panel lock, press and hold the button for

roughly 3 seconds. When the display visualises “KEY LOCK”, the control

panel is locked (except for the ON/OFF button ). This will prevent

accidental modications to wash cycles, especially when children are at

home. To deactivate the control panel lock, press and hold the

button for approximately 3 seconds.

Locked door indicator

When lit, the symbol indicates that the door is locked. To prevent any

damage, wait until the symbol turns o before opening the door.

To open the door while a cycle is in progress, press the START/PAUSE

button ; if the symbol is o, the door can be opened.

FIRSTTIME USE

Once the appliance has been installed, and before you use it for the rst

time, run a wash cycle with detergent and no laundry, using the wash

cycle 9 (60°).

DAILY USE

Prepare the laundry by following the suggestions appearing under the

“TIPS AND SUGGESTIONS” section.

- Press the ON/OFF button ; “HOTPOINT” will appear on the display.

- Open the door. Load the laundry while making sure not to exceed the

maximum load quantity indicated in the wash cycle table.

- Pull out the detergent dispenser drawer and pour the detergent into the

relevant compartments, as described in the “DETERGENT DISPENSER

DRAWER” section.

- Close the door.

- The machine automatically selects the default temperature and spin

speed set for the selected wash cycle.

- Select the desired wash cycle.

- Select the desired options.

- Press the START/PAUSE button to start the wash cycle; the door will

lock ( symbol on).

PAUSING A CYCLE

To pause the wash cycle, press the START/PAUSE button again. To start

the wash cycle from the point at which it was interrupted, press the

START/PAUSE button again.

OPENING THE DOOR, IF NECESSARY

Once a cycle starts, the symbol turns on to signal that the door cannot

be opened. While a wash cycle is running, the door remains locked. To

open the door while a cycle is under way, for example, to add or remove

garments, press the START/PAUSE button to pause the cycle. If the

symbol is not lit, the door may be opened. Press the START/PAUSE

button again to continue the cycle.

ADDING GARMENTS

An icon on the display will signal when additional garments can be

introduced into the washing machine, without decreasing the washing

performance. To add garments, rst stop the washing machine by pressing

the START/PAUSE button then open the door and insert them.

Press the START/PAUSE button again to restart the wash cycle from

the point at which it was interrupted.

CHANGING A RUNNING WASH CYCLE

To change a wash cycle while it is in progress, pause the washing machine

using the START/PAUSE button, then select the desired cycle and press

the START/PAUSE button again.

! To cancel a cycle that has already begun, press and hold the ON/OFF

button. The cycle will be stopped and the machine will switch o.

AT THE END OF THE WASH CYCLE

This will be indicated by the word “CYCLE END” on the display; when the

symbol switches o, the door may be opened. Open the door, unload the

laundry and switch o the machine. If you do not press ON/OFF button,

the washing machine will switch o automatically after about 15 minutes.

OPTIONS

- If the selected option is incompatible with the set wash cycle or with

another previously selected option, in the menu the name of

incompatible option is represented in grey color and the wording “Not

available” will appear on the display, accompanied by a buzzer, the

option will not be activated.

Steam Hygiene

This option enhances washing performance by generating steam during

the wash cycle to remove any bacteria from the bres, which are treated

at the same time. Place the laundry in the drum, choose a compatible

programme and select option Steam Hygiene.

! The steam generated during the operation of the washing machine may

cause the porthole door to become hazy.

Start Delay

To set a delayed start for the selected cycle, press the corresponding

button repeatedly until the desired delay period is reached. When this

option has been activated, the selected values of delay start will appear

on the display. To remove the delayed start setting, press the button until

“--:--” appears on the display.

Active Care

The detergent, premixed with water, creates an unique emulsion able

to better penetrate the bers of the garments, cleaning stains at even

low temperatures, preserving both colors and fabrics. These results are

obtained also due to the multiple dierent specic movements of the

drum which best take care of the garments.

Final Care

The washing machine will perform gentle tumbling through slow

rotations of the drum. Final Care option starts after the cycle ends for a

maximum duration of 6h and you can interrupt at any time by pressing

any button on control panel or turning the knob.

I Rapid / Eco

After pushing the button for the 1st time, option Rapid is selected and the

cycle duration will be reduced.

Otherwise after pushing for the 2nd time, option Eco is selected allowing

more energy saving.

Multi Rinse

By selecting this option, the eciency of the rinse is increased and optimal

detergent removal is guaranteed. It is particularly useful for sensitive skin.

Press the button once, two or three times to select an additional 1, 2 or 3

rinses after the standard cycle rinse and remove all traces of detergent.

Press the button again to go back to the “Normal rinse” rinse type.

Easy Iron

By selecting this function, the wash and the spin cycles will be modied in

order to reduce the formation of creases.

Cold Wash

This option saves energy by not heating the water used to wash your

laundry – an advantage both to the environment and to your energy bill.

Instead, intensied wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage of a liquid

detergent.

Prewash

Allows you to perform a prewash.

Temperature

Each wash cycle has a pre-dened temperature. To modify the temperature,

press the “

60°

40°

” button. The value will appear on the display.

Spin

Each wash cycle has a pre-dened spin speed. To modify the spin speed,

press the “ ” button. The value will appear on the display.

DESCALE AND CLEAN PROCEDURE

An icon on the display will regularly (roughly every 50 cycles) remind users

that is time to run a maintenance cycle to clean the washing machine and

combat limescale build-up and bad odours.

To delete the descale alert turn the knob or push any button (including ON/

OFF button).

For optimal maintenance we suggest using WPRO Limescale and grease

remover, according to the instructions shown on the package.

The product can be purchased by contacting the technical assistance service

or through the website www.whirlpool.eu.

Whirlpool declines all liability for any damages to the appliance caused by the

use of other cleaning products for washing machines available on the market.

TIPS AND SUGGESTIONS

Divide the laundry according to:

Type of fabric (cotton, mixed bres, synthetics, wool, garments to be

hand-washed). Colour (separate coloured garments from whites, wash

new coloured garments separately). Delicates (small garments – such as

nylon stockings – and items with hooks – such as bras: insert them in a

fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washing machine and

the drum. Check all buttons.

CARE AND MAINTENANCE

Before performing cleaning and maintenance, switch the washing machine

o and disconnect it from the mains power. Do not use ammable liquids to

clean the washing machine.

Cutting o the water and electricity supplies

Close the water tap after every wash. This will limit wear on the hydraulic

system inside the washing machine and help to prevent leaks.

Unplug the washing machine when cleaning it and during all

maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance can be cleaned using

a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Caring for the door and drum

Always leave the porthole door ajar in order to prevent unpleasant odours

from forming.

ANTIMICROBIAL SEAL

The seal around the porthole door is made from a special mixture

ensuring antimicrobial protection, thus reducing bacterial proliferation

up to 99.99%.

The seal contains zinc pyrithione, a biocidal substance which reduces the

proliferation of harmful microbes (*) such as batteries and mould prone to

causing stains, unpleasant odours and product deterioration.

(*) According to tests performed by the University of Perugia, Italy

on: Staphylococcus aureus, Escherichia coll, Pseudomonas aeruginosa,

Candida albicans, Aspergillus niger, Penicillium digitatum

In rare cases an allergic reaction may be caused by prolonged contact between seal

and skin.

ACCESSORIES

Contact our Technical Assistance Service to check whether the following

accessories are available for this washing machine model.

Stacking kit

With this accessory you can secure the tumble dryer to the upper part of

your washing machine to save space and facilitate loading and unloading

of the tumble dryer.

TRANSPORT AND HANDLING

Do not lift the washing machine by gripping it from the upper section.

Unplug the appliance and close the water tap. Check that the door and

detergent dispenser drawer are tightly closed. Detach the lling hose

from the water tap then detach the drain hose. Empty all the water

remaining in the hoses and secure the latter so that they do not get

damaged during transport. Apply the transport bolts back on. Repeat, in

reverse order, the transport bolt removal procedure described in the

“Installation instructions”.

TROUBLESHOOTING

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily

solved using the following list.

Anomalies Possible causes / Solution

The washing machine does

not start.

The appliance is not plugged into the socket fully, or not enough to make contact.

There is no power in the house.

The wash cycle does not start.

The washing machine door is not closed properly.

The ON/OFF button has not been pressed.

The START/PAUSE button has not been pressed.

The water tap has not been opened.

A delay has been set for the start time.

The Demo Mode is active (see below how to deactivate).

The washing machine does

not ll with water (“ ”

appears on the display).

The water inlet hose is not connected to the tap.

The hose is bent.

The water tap has not been opened.

There is no water supply in the house.

The pressure is too low.

The START/PAUSE button has not been pressed.

The washing machine

continuously loads and

unloads water.

The drain hose is not tted between 65 and 100 cm from the oor.

The free end of the hose is immersed in water.

The wall drainage system is not tted with a breather pipe.

If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the

Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems relating

to back-siphonage, causing the washing machine to ll with water and drain continuously. Special anti-siphon

valves are available in shops and help to prevent this inconvenience.

The washing machines does

not drain and the symbol

(F9E1) on the display.

Clean the pump lter (see Care and maintenance chapter)

The drain hose is bent.

The drainage duct is clogged.

The washing machine

vibrates a lot during the spin

cycle.

Transport bolts have been not removed correctly during installation.

The washing machine is not leveled.

The washing machine is tucked between furniture cabinets and the wall.

The washing machine leaks.

The water inlet hose is not screwed on properly.

The detergent dispenser drawer is obstructed.

The drain hose is not properly attached.

The symbol appear and

the display visualises an error

code (e.g.: F1E1, F4...).

Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

There is too much foam.

The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and

machine wash”, or the like).

Too much detergent was used.

“ ” phase icon blinks, “0”

spin speed displayed .

Unbalance of laundry load prevented spin cycle, to protect the washing machine.

If you want to spin the wet laundry, add more laundry items of dierent sizes and start “Spin&Drain” programme.

Avoid small laundry loads consisting of few big, absorbent pieces of laundry / wash dierent sizes of articles in one

load.

Not possible to connect .

Please verify with your smart device that the signal strength of your home wireless network close to the appliance

is good.

Check connection of router to Internet and eventually contact your Internet service provider.

If router is connected to Internet follow app instructions for connect router to appliance.

Disable the DEMO MODE : The following actions must be carried out in sequence, without breaks. Switch the machine ON and then switch it OFF again. Press

the START/PAUSE button until the buzzer is heard. Switch the machine on again. The “DEMO” indicator ashes and then turns OFF.

CLEANING & MAINTENANCE

For any cleaning and maintenance, switch o and unplug the washing machine.

Do not use ammable uids to clean the washing machine.

CLEANING THE OUTSIDE OF THE WASHING MACHINE

Use a soft damp cloth to clean the outer parts of the washing

machine.

Do not use glass or general purpose cleaners, scouring

powder or similar to clean the control panel – these

substances might damage the printing.

CHECKING THE WATER SUPPLY HOSE

Check the inlet hose regularly for brittleness and cracks. If

damaged, replace it by a new hose available through our

After-Sales Service or your specialist dealer.

Depending on the hose type:

If the inlet hose has a transparent coating, periodically check

if the colour intensies locally. If yes, the hose may have a leak

and should be replaced.

For water stop hoses: check the small safety valve inspection

window (see arrow). If it is red, the water stop function was

triggered, and the hose must be replaced by a new one.

For unscrewing this hose, press the release button (if

available) while unscrewing the hose.

CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE

1. Close water tap and unscrew the inlet hose.

2. Clean the mesh lter at the hose’s end carefully with a

ne brush.

3. Now unscrew the inlet hose on the back of the washing

machine by hand. Pull out the mesh lter from the valve

on the back of the washing machine with pliers and

carefully clean it.

4. Insert the mesh lter again. Connect the inlet hose to

water tap and washing machine again. Do not use a tool

to connect the inlet hose. Open the water tap and check

that all connections are tight.

CLEANING THE DETERGENT DISPENSER

CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER

Switch o and unplug the washing machine before cleaning the water lter or draining residual water. If you used a hot

wash programme, wait until the water has cooled down before draining any water.

Clean the water lter regularly, to avoid that the water cannot drain after the wash due to obstruction of the lter.

If the water cannot drain, the display indicates that the water lter may be clogged.

1. Remove the kick panel: Using a screwdriver, do that which

is shown in the following gure.

2. Container for the drained water:

Place a low and wide container under the water lter in

order to collect the residual water.

3. Drain the water:

Slowly turn the lter counter-clockwise until all the water

has come out. Allow the water to ow out without

removing the lter. Once the container is full, close the

water lter by turning it clockwise. Empty the container.

Repeat the procedure until all the water has been drained.

4. Remove lter: Lay a cotton cloth beneath the water lter,

which can absorb a small amount of rest water. Then

remove the water lter by turning it out anticlockwise.

5. Clean the water lter: remove residues in the lter and

clean it under running water.

6. Insert the water lter and reinstall the plinth: Reinsert the water

lter again by turning it in clockwise direction. Make sure to turn

it in as far as it goes; the lter handle must be in vertical position.

To test water tightness of the water lter, you can pour about 1

liter of water into the detergent dispenser. Then reinstall the

plinth.

Remove the dispenser by raising it and

pulling it out (see gure).

Wash it under running water; this

operation should be repeated frequently.

TRANSPORT AND HANDLING

Never lift the washing machine by holding it at the worktop.

1. Pull out the mains plug, and close the water tap.

2. Make sure that door and detergent dispenser are properly

closed.

3. Disconnect the inlet hose from the water tap, and remove

the drain hose from your draining point. Remove all rest

water from the hoses, and x them so that they cannot get

damaged during transport.

4. Ret the transport bolts. Follow the instructions for

removing the transport bolts in the “Installation Guide” in

reverse order.

Important: Do not transport the washing machine without

having xed the transport bolts.

AFTERSALES SERVICE

BEFORE CALLING THE AFTERSALES SERVICE

1. See if you can solve the problem by yourself with the help

of the suggestions given in the TROUBLESHOOTING

2. Switch the appliance o and back on again to see if the

fault persists.

IF AFTER THE ABOVE CHECKS THE FAULT STILL

OCCURS, GET IN TOUCH WITH THE NEAREST

AFTERSALES SERVICE

To receive assistance, call the number shown on the warranty

booklet or follow the instructions on the website

www.hotpoint.eu

When contacting our Client After sales service, always specify:

• a brief description of the fault;

• the type and exact model of the appliance;

xxxxxxxxxxxx

• the service number (number after the word Service on the

rating plate).

• your full address;

• your telephone number.

If any repairs are required, please contact an authorised after-

sales service (to guarantee that original spare parts will be used

and repairs carried out correctly).

1. 2. 3.

4. 5.

150 ml

100 ml

50 ml

10 mm - 0,39 inch

2 cm - 0,7 inch

6. 7.

10. 11.

12.

13. 14.

max 100 cm

39 inch

min 65 cm

25 inch

max 100 cm

39 inch

min 65 cm

25 inch

max 100 cm

39 inch

min 65 cm

25 inch

9.8.

max 0,5 cm

max 0,2 inch

Before using the appliance, read these safety instruc-

tions. Keep them nearby for future reference. These

instructions and the appliance itself provide impor-

tant safety warnings, to be observed at all times.

The manufacturer declines any liability for failure to

observe these safety instructions, for inappropriate

use of the appliance or incorrect setting of controls.

Very young children (0-3 years) should be kept

away from the appliance. Young children

(3-8years) should be kept away from the

appliance unless continuously supervised.

Children from 8years old and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and knowledge

can use this appliance only if they are supervised

or have been given instructions on safe use and

understand the hazards involved. Children must

not play with the appliance. Cleaning and user

maintenance must not be carried out by children

without supervision. Never open the door forcibly

or use it as a step.

PERMITTED USE

CAUTION: The appliance is not intended to be

operated by means of an external switching

device, such as a timer, or separate remote

controlled system.

This appliance is intended to be used in

household and similar applications such as: sta

kitchen areas in shops, oces and other working

environments; farm houses; by clients in hotels,

motels, bed & breakfast and other residential

environments.

Do not load the machine above the maximum

capacity (kg of dry cloth) indicated in the

programme table.

This appliance is not for professional use. Do

not use the appliance outdoors.

Do not use any solvents (e.g. turpentine,

benzene), detergents containing solvents,

scouring powder, glass or general purpose

cleaners, or ammable uids; do not machine

wash fabrics that have been treated with solvents

or ammable liquids.

INSTALLATION

The appliance must be handled and installed by

two or more persons- risk of injury. Use protective

gloves to unpack and install- risk of cuts.

If you want to stack a dryer on top of your

washing machine, rst contact our After-Sales

Service or your specialist dealer to verify whether

this is possible. This is only possible if the dryer is

attached to the washing machine by means of

appropriate stacking kit available through our

After- Sales Service or your specialist dealer.

Move the appliance without lifting it by the

worktop or top lid.

Installation, including water supply (if any) and

electrical connections and repairs must be carried

out by a qualied technician. Do not repair or

replace any part of the appliance unless

specically stated in the user manual. Keep

children away from the installation site. After

unpacking the appliance, make sure that it has not

been damaged during transport. In the event of

problems, contact the dealer or your nearest

After-sales Service. Once installed, packaging

waste (plastic, styrofoam parts etc.) must be

stored out of reach of children- risk of suocation.

The appliance must be disconnected from the

power supply before any installation operation-

risk of electric shock. During installation, make

sure the appliance does not damage the power

cable - risk of re or electric shock. Only activate

the appliance when the installation has been

completed.

Do not install your appliance where it may be

exposed to extreme conditions, such as: poor

ventilation, temperatures below 5 °C or above 35 °C.

When installing the appliance make sure that

the four feet are stable and resting on the oor,

adjusting them as required, and check that the

appliance is perfectly to level using a spirit level.

If the appliance is being installed on wood or

“oating” oors (certain parquet and laminate

materials), secure a 60x60x3cm (at least) sheet

of plywood to the oor then place the appliance

on top of this.

Connect the water inlet hose(s) to the water

supply in accordance with the regulations of your

local water company.

For cold ll only models: do not connect to the

hot water supply.

For models with hot ll: the hot water inlet

temperature must not exceed 60°C.

The washing machine is tted with transport

bolts to prevent any possible damage to the

interior during transport. Before using the

machine, it is imperative that the transport bolts

are removed. After their removal, cover the

openings with the 4 enclosed plastic caps.

After installation of the device, wait a few hours

before starting it so that it acclimates to the

environmental conditions of the room.

Make sure that the ventilation openings in the

base of your washing machine (if available on

your model) are not obstructed by a carpet or

other material.

Use only new hoses to connect the appliance

to the water supply. The old hose-sets should not

be reused.

The supply water pressure must be in the 0.1-1

Mpa range.

SAFETY INSTRUCTIONS IMPORTANT TO BE READ AND OBSERVE

859991556620

ELECTRICAL WARNINGS

It must be possible to disconnect the appliance

from the power supply by unplugging it if plug is

accessible, or by a multi-pole switch installed

upstream of the socket in accordance with the

wiring rules and the appliance must be earthed in

conformity with national electrical safety standards.

Do not use extension leads, multiple sockets or

adapters. The electrical components must not be

accessible to the user after installation. Do not use

the appliance when you are wet or barefoot. Do

not operate this appliance if it has a damaged

power cable or plug, if it is not working properly, or

if it has been damaged or dropped.

If the supply cord is damaged, it must be

replaced with an identical one by the manufacturer,

its service agent or similarly qualied persons in

order to avoid a hazard - risk of electric shock.

CLEANING AND MAINTENANCE

WARNING: Ensure that the appliance is switched

o and disconnected from the power supply

before performing any maintenance operation;

never use steam cleaning equipment - risk of

electric shock.

DISPOSAL OF PACKAGING MATERIALS

The packaging material is 100% recyclable and is marked with the

recycle symbol .

The various parts of the packaging must therefore be disposed of

responsibly and in full compliance with local authority regulations

governing waste disposal.

DISPOSAL OF HOUSEHOLD APPLIANCES

This appliance is manufactured with recyclable or reusable materials.

Dispose of it in accordance with local waste disposal regulations.

For further information on the treatment, recovery and recycling of

household electrical appliances, contact your local authority, the

collection service for household waste or the store where you purchased

the appliance. This appliance is marked in compliance with European

Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent

negative consequences for the environment and human health.

The symbol on the product or on the accompanying documentation

indicates that it should not be treated as domestic waste but must be

taken to an appropriate collection center for the recycling of electrical

and electronic equipment.

DECLARATIONS OF CONFORMITY

The Manufacturer, Whirlpool EMEA S.p.A., declares that this LB 2006

TRF model of household appliance with radio equipment GEN 4 is

compliant with directive 2014/53/UE.

The complete text of the declaration of conformity is present at the

following website: docs.hotpoint.eu.

The radio equipment operates in the 2.4 GHz ISM frequency band,

the maximum radio-frequency power transmitted does not exceed

20 dBm (e.i.r.p.).

This product includes certain open source software developed by

third parties. The open source license usage statement is available at

the following website: docs.hotpoint.eu.