Hotpoint NLLCD 1047 WC AD EU User Manual

Displayed below is the user manual for NLLCD 1047 WC AD EU by Hotpoint which is a product in the Washing Machines category. This manual has pages.

Related Manuals

Hotpoint RZ 1047 W EU Manual

Hotpoint NLLCD 947 WD ADW UK Manual

Hotpoint NLLCD 1165 WD ADW UK Manual

Hotpoint NLLCD 1045 WD AW UK Manual

Hotpoint NLLCD 1044 WD AW UK N Manual

MSI 14 A10M-1047AU Manual

Hotpoint NM11 946 WC A UK Manual

Quick Guide

THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.

To receive more comprehensive assistance, register the

appliance on

www.hotpoint.eu/register

Before using the appliance carefully read the Health and Safety guide.

Before using the machine, it is imperative that the transport bolts are removed. For more

detailed instructions on how to remove them, see the Installation Guide.

CONTROL PANEL

WASH CYCLE TABLE

For all testing institutes:

2) Long cotton cycle: set wash cycle 3 with a temperature of 40°C.

3) Long synthetics cycle: set wash cycle 4 with a temperature of 40°C.

* By selecting the 14 cycle and excluding the spin cycle, the washing machine will drain only.

** The duration of the wash cycles can be checked on the display.

The cycle duration indicated on the display or instruction manual is an estimate based on

standard conditions. The actual duration may vary in relation to several factors, such as

the temperature and pressure of the incoming water, ambient temperature, amount of

detergent, load quantity and type, load balancing and any additional options selected.

1) Test wash cycle in compliance with regulation 1061/2010:

This cycle is designed for normally soiled cotton loads and is the most ecient in terms of

both electricity and water consumption; it should be used for garments washable at 60°C or

at 40°C. The actual washing temperature may dier from the indicated value.

1. RAPID / ECO button

2. UP / DOWN buttons

3. ON/OFF button

4. ACTIVE CARE button and indicator light

5. START/PAUSE button

6. CONFIRM / KEY LOCK button

7. START DELAY button

8. SPIN button

9. TEMPERATURE button

10. OPTIONS / SETTINGS button

11. STEAM HYGIENE/FAVOURITES button

12. WASH CYCLE SELECTOR KNOB

13. Programme Key

Maximum load 10 kg

Power input in o mode 0.5 W / in left-on mode 8 W

Active

Care

Add

Gar-

ments

()

Detergents and

Additives

Recommended

detergent

Residual damp-

ness %

Energy consump-

tion kWh

Total water l

Wash cycle Temperature Max.

spin speed

(rpm)

Max.

load

(kg)

Duration

(min-

utes)

Pre-

wash Wash Fabric

softener Powder Liquid

Default Range 1 2 3

1 Mixed 40°C - 40°C 1400 10 **      –– – –

2 Eco Cotton (1) 60°C 60°C 1400 10 330 ––    53 0,67 60

40°C 1400 10 330 ––    53 0,67 96

3 Cotton (2) 40°C - 60°C 1400 10 235 ––    53 1,4 107

4 Synthetics (3) 40°C - 60°C 1200 5,5 175 –      53 0,83 56

5 Delicates 40°C - 40°C 1000 5,5 **   –  –– – –

6Wool 40°C - 40°C 800 2,5 ** – –  –– – –

7 Anti Allergy 60°C - 60°C 1400 5,5 ** – –    – – –

8 Anti Stain 40° 40°C - 40°C 1000 5,5 **   –  –– – –

9 White 40°C - 90°C 1400 10 **        – – –

10 Steam Refresh – – – 2 ** – – – – – – – – – –

11 Rapid 30 min 30°C - 30°C 800 5,5 **   –  –– – –

12 Specials

• Bed & Bath 60°C - 60°C 1400 10 **   –    – – –

• Shirts 40°C - 40°C 600 2 ** – –  –– – –

• Business 30°C - 30°C 400 2 ** ––  –– – –

• Baby 40°C - 40°C 800 4 ** – –  –– – –

• Duvet 30°C - 30°C 1000 3,5 ** ––  –– – –

• Silk & Curtains 30°C - 30°C – 1 ** – –  –– – –

• Jeans 40°C - 40°C 800 4 ** ––  –– – –

• Rapid 15 min 30°C - 30°C 800 4,5 ** – –  –– – –

• Fitness 30°C - 30°C 600 4 ** ––  –– – –

• Cuddly toys 30°C - 30°C – 1 ** ––– – – – –

13 Favourites: allows for any wash cycle to be stored.

14 Spin & Drain * – – 1400 10 ** – – – – – – – – – –

15 Rinse & Spin – – 1400 10 ** – – – – – – – – –

 Required dosage  Optional dosage

! Turning the knob to position 12 allows for accessing the menu from which to set additional

washing programmes.

1 2 3

911 10

DISPLAY

! The “Programme key” situated inside the detergent dispenser shows all the

available wash cycles together with a graphic guide on how to use the

individual dispenser compartments.

WASH CYCLES

Follow the instructions on the symbols of the garment’s wash

care label. The value indicated in the symbol is the maximum

recommended temperature for washing the garment.

Mixed

For washing lightly to normally soiled resilient garments in cotton, linen,

synthetic bres and mixed bres.

Eco Cotton 60°/40°

Suitable for washing moderately soiled cotton garments. At 40°C and

60°C it is the standard cycle for washing cotton garments, and is the most

ecient in terms of combined water and electricity consumption.

Cotton

Normally to heavily soiled and robust cottons .

Synthetics

Suitable for washing moderately soiled garments made of synthetic bres

(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.

Delicates

For washing very delicate garments. It is advisable to turn the garments

inside out before washing them. For best results, use liquid detergent on

delicate garments.

Wool - Woolmark Apparel Care - Green:

The “Wool” wash cycle is approved by the Woolmark Company for

washing wool garments classied as “hand-washable”, provided that the

wash complies with the instructions appearing on the garment’s label

and with those provided by the manufacturer of this washing machine.

(M1135)

Anti Allergy

Suitable for removing major allergens such as pollen, mites and cat or dog hair.

Anti Stain 40°

The programme is suitable to heavily-soiled garments with resistant

colours. It ensures a washing class that is higher than the standard class (A

class). When running the programme, do not mix garments of dierent

colours. We recommend the use of powder detergent. Pre-treatment with

special additives is recommended if there are obstinate stains.

White

For washing normally to heavily soiled towels, underwear, table and bed

linen, etc in resilient cotton and linen. Only when the temperature is

selected at 90°C the cycle is provided with a prewash phase before main

washing phase. In this case it is recommended to add detergent both, in

the prewash and main wash section.

Steam Refresh

The garments will be damp once the cycle is completed, so we recommend

hanging them to dry (2 kg, roughly 3 items). This programme refreshes

garments by removing bad odours and relaxing the bres. Insert dry items

only (that are not dirty) and select programme “Steam Refresh”. Garments

will be a little damp at the end of the cycle and can be worn after a few

minutes. The “Steam Refresh” programme makes ironing easier.

! Do not add softeners or detergents.

! Not recommended for wool or silk garments.

Rapid 30 min

For washing lightly soiled garments quickly. This cycle lasts only 30

minutes, saving time and energy.

Specials

• Bed & Bath

For washing home linen in a single cycle. It optimises the use of fabric

softener and allows for saving time and electricity. We recommend the

use of powder detergent.

• Shirts

Use the special wash cycle to wash shirts in dierent fabrics and

colours to guarantee they receive the best possible care.

• Business

Program for clothes used infrequently or only slightly dirty (do not use

for dry clean garment).

Follow the instructions of the garment’s wash care label.

• Baby

Use the special wash cycle to remove the remove the soiling typically

caused by babies, while removing all traces of detergent from nappies

in order to prevent the delicate skin of babies from suering allergic

reactions. The cycle has been designed to reduce the amount of

bacteria by using a greater quantity of water and optimising the eect

of special disinfecting additives added to the detergent.

• Duvet

Designed for washing eiderdown padded items such as double or

single duvets, cushions and anoraks. It is recommended to load such

padded items in the drum with the edges folded inwards and not to

exceed ¾ of the drum’s volume. For optimal washing, we recommend

using a liquid detergent.

• Silk & Curtains

use special wash cycle to wash all silk garments or curtains. We

recommend the use of special detergent which has been designed to

wash delicate clothes.

For washing curtains, fold and place them in a pillow case or mesh bag.

• Jeans

Turn garments inside-out before washing and use a liquid detergent.

• Rapid 15 min

for washing lightly soiled garments in a short time. Not suitable for

wool, silk and garments to be washed by hand.

• Fitness

Sportswear in knitwear or microbers with a normal degree of dirt and

sweat.

• Cuddly toys

With this program it is possible to remove dust more easily and wash

better cuddle toys.

Spin & Drain

Spins the load then empties the water. For resilient garments. If you

exclude the spin cycle, the machine will drain only

Rinse & Spin

Rinses and then spins. For resilient garments.

DISPLAY

The display is useful when programming the washing machine and

provides plenty of information.

COTTON

--:--

1:40

140040°

By pressing the and buttons, it is possible to select the desired

option and conrm it with the button.

The rst time the machine is switched on, you will be asked to select the

language and the display will automatically display the language selection

menu.

To select the desired language, press the and buttons; to conrm

the selection, press the button.

Area A will display the following: the icon and selected washing programme,

the washing phases and the time remaining to the end of the wash cycle.

Area B will display: the selected options, the energy and water consumption

for the chosen cycle and the button lock symbol.

1. Top

2. Detergent dispenser drawer

3. Control panel

4. Handle

5. Porthole door

6. Drain pump (behind the plinth)

7. Plinth (removable)

8. Adjustable feet (2)

DETERGENT DISPENSER DRAWER

compartment 1: Pre-wash detergent

(powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

If liquid detergent is used, it is recommended

that the removable plastic partition A (supplied)

be used for proper dosage.

If powder detergent is used, place the partition

into slot B.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overow the grid.

! Use powder detergent for white cotton garments, for pre-washing, and

for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

PRODUCT DESCRIPTION

Area C will display the default temperature value on the basis of the set

programme; if the programme does not include the setting of the

temperature, the area will display the “-- °” symbol.

Area D will display the default spin cycle speed on the basis of the set

programme; if the programme does not include the setting of the spin

cycle, the area will display the “--” symbol.

Area E will display the time remaining to the start of the selected

programme if the DELAYED START function was set.

Pressing and holding button F for 3 seconds allows for memorising one or

more preferred wash cycles.

To use the memorised cycles, turn the knob to position 13.

Pressing button G allows for accessing the menu from which to set

additional washing options.

Pressing and holding button G for 3 seconds allows for accessing the

settings menu:

- Language: by pressing the and buttons, the user can select the

desired language and conrm it with the button.

- Sound: by pressing the and buttons, the user can activate or

deactivate the sound of the buttons and conrm it with the button.

- Display brightness: by pressing the and buttons, the user can

select the type of display brightness and conrm it with the button.

- Restoring the factory settings: pressing and holding the button for 2

seconds restores the factory settings.

! During a wash cycle if the user does not interact with the display for 5

minutes, the SCREEN SAVER will activate. To return to the previous window,

simply press any button.

DISPLAY INDICATORS

Failure: Call Service

Refer to Troubleshooting section

Failure: Water lter clogged

Water cannot be drained; water lter might be blocked

Failure: No water

No or not sucient inlet water.

In the event of any failure, refer to the “Troubleshooting” section.

Key Lock

To activate the control panel lock, press and hold the button for

roughly 3 seconds. When the display visualises “KEY LOCK”, the control

panel is locked (except for the ON/OFF button ). This will prevent

accidental modications to wash cycles, especially when children are at

home. To deactivate the control panel lock, press and hold the

button for approximately 3 seconds.

Locked door indicator

When lit, the symbol indicates that the door is locked. To prevent any

damage, wait until the symbol turns o before opening the door.

To open the door while a cycle is in progress, press the START/PAUSE

button ; if the symbol is o, the door can be opened.

FIRSTTIME USE

Once the appliance has been installed, and before you use it for the rst

time, run a wash cycle with detergent and no laundry, using the wash

cycle 9 (60°).

DAILY USE

Prepare the laundry by following the suggestions appearing under the

“TIPS AND SUGGESTIONS” section.

- Press the ON/OFF button ; “HOTPOINT” will appear on the display.

- Open the door. Load the laundry while making sure not to exceed the

maximum load quantity indicated in the wash cycle table.

- Pull out the detergent dispenser drawer and pour the detergent into the

relevant compartments, as described in the “DETERGENT DISPENSER

DRAWER” section.

- Close the door.

- The machine automatically selects the default temperature and spin

speed set for the selected wash cycle.

- Select the desired wash cycle.

- Select the desired options.

- Press the START/PAUSE button to start the wash cycle; the door will

lock ( symbol on).

PAUSING A CYCLE

To pause the wash cycle, press the START/PAUSE button again. To start

the wash cycle from the point at which it was interrupted, press the

START/PAUSE button again.

OPENING THE DOOR, IF NECESSARY

Once a cycle starts, the symbol turns on to signal that the door cannot

be opened. While a wash cycle is running, the door remains locked. To

open the door while a cycle is under way, for example, to add or remove

garments, press the START/PAUSE button to pause the cycle. If the

symbol is not lit, the door may be opened. Press the START/PAUSE

button again to continue the cycle.

ADDING GARMENTS

An icon on the display will signal when additional garments can be

introduced into the washing machine, without decreasing the washing

performance. To add garments, rst stop the washing machine by

pressing the START/PAUSE button then open the door and insert

them.

Press the START/PAUSE button again to restart the wash cycle from

the point at which it was interrupted.

CHANGING A RUNNING WASH CYCLE

To change a wash cycle while it is in progress, pause the washing machine

using the START/PAUSE button, then select the desired cycle and press

the START/PAUSE button again.

! To cancel a cycle that has already begun, press and hold the ON/OFF

button. The cycle will be stopped and the machine will switch o.

AT THE END OF THE WASH CYCLE

This will be indicated by the word “CYCLE END” on the display; when the

symbol switches o, the door may be opened. Open the door, unload the

laundry and switch o the machine. If you do not press ON/OFF button,

the washing machine will switch o automatically after about 15 minutes.

OPTIONS

- If the selected option is incompatible with the set wash cycle or with

another previously selected option, in the menu the name of

incompatible option is represented in grey color and the wording “Not

available” will appear on the display, accompanied by a buzzer, the

option will not be activated.

Steam Hygiene

This option enhances washing performance by generating steam during

the wash cycle to remove any bacteria from the bres, which are treated

at the same time. Place the laundry in the drum, choose a compatible

programme and select option Steam Hygiene.

! The steam generated during the operation of the washing machine may

cause the porthole door to become hazy.

Start Delay

To set a delayed start for the selected cycle, press the corresponding

button repeatedly until the desired delay period is reached. When this

option has been activated, the selected values of delay start will appear

on the display. To remove the delayed start setting, press the button until

“--:--” appears on the display.

Active Care

The detergent, premixed with water, creates an unique emulsion able

to better penetrate the bers of the garments, cleaning stains at even

low temperatures, preserving both colors and fabrics. These results are

obtained also due to the multiple dierent specic movements of the

drum which best take care of the garments.

Final Care

The washing machine will perform gentle tumbling through slow

rotations of the drum. Final Care option starts after the cycle ends for a

maximum duration of 6h and you can interrupt at any time by pressing

any button on control panel or turning the knob.

I Rapid / Eco

After pushing the button for the 1st time, option Rapid is selected and the

cycle duration will be reduced.

Otherwise after pushing for the 2nd time, option Eco is selected allowing

more energy saving.

Multi Rinse

By selecting this option, the eciency of the rinse is increased and optimal

detergent removal is guaranteed. It is particularly useful for sensitive skin.

Press the button once, two or three times to select an additional 1, 2 or 3

rinses after the standard cycle rinse and remove all traces of detergent.

Press the button again to go back to the “Normal rinse” rinse type.

Easy Iron

By selecting this function, the wash and the spin cycles will be modied in

order to reduce the formation of creases.

Cold Wash

This option saves energy by not heating the water used to wash your

laundry – an advantage both to the environment and to your energy bill.

Instead, intensied wash action and water optimisation ensure great

wash results in the same average time of a standard cycle.

For the best washing results we recommend the usage of a liquid

detergent.

Prewash

Allows you to perform a prewash.

Temperature

Each wash cycle has a pre-dened temperature. To modify the temperature,

press the “

60°

40°

” button. The value will appear on the display.

Spin

Each wash cycle has a pre-dened spin speed. To modify the spin speed,

press the “ ” button. The value will appear on the display.

DESCALE AND CLEAN PROCEDURE

An icon on the display will regularly (roughly every 50 cycles) remind users

that is time to run a maintenance cycle to clean the washing machine and

combat limescale build-up and bad odours.

To delete the descale alert turn the knob or push any button (including ON/

OFF button).

For optimal maintenance we suggest using WPRO Limescale and grease

remover, according to the instructions shown on the package.

The product can be purchased by contacting the technical assistance service

or through the website www.whirlpool.eu.

Whirlpool declines all liability for any damages to the appliance caused by the

use of other cleaning products for washing machines available on the market.

TIPS AND SUGGESTIONS

Divide the laundry according to:

Type of fabric (cotton, mixed bres, synthetics, wool, garments to be

hand-washed). Colour (separate coloured garments from whites, wash

new coloured garments separately). Delicates (small garments – such as

nylon stockings – and items with hooks – such as bras: insert them in a

fabric bag).

Empty the pockets:

Objects such as coins or lighters can damage the washing machine and

the drum. Check all buttons.

CARE AND MAINTENANCE

Before performing cleaning and maintenance, switch the washing machine

o and disconnect it from the mains power. Do not use ammable liquids to

clean the washing machine.

Cutting o the water and electricity supplies

Close the water tap after every wash. This will limit wear on the hydraulic

system inside the washing machine and help to prevent leaks.

Unplug the washing machine when cleaning it and during all

maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance can be cleaned using

a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

Remove the dispenser drawer by lifting and pulling it outwards. Wash it

under running water; this procedure should be eected regularly.

Caring for the door and drum

Always leave the porthole door ajar in order to prevent unpleasant odours

from forming.

Cleaning the pump

The washing machine is tted with a self-cleaning pump that does not

require any maintenance. Small items (such as coins or buttons) may

sometimes fall into the protective pre-chamber situated at the base of the

pump.

! Make sure that the wash cycle has ended and unplug the appliance.

To access the pre-chamber:

1. remove the covering panel on the front side of the machine by inserting

a screwdriver in the centre and sides of the panel and using it as a lever;

2. place a low and wide container under the water lter in order to collect

the residual water.

3. loosen the drainage pump cover by turning it anti-clockwise: it is

normal for some water to leak out;

4. clean the inside thoroughly;

5. screw the cover back on;

6. put the panel back in place, making sure the hooks slot in place before

pushing the panel onto the appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If it is cracked or broken, it

must be replaced: during wash cycles, the high pressure of the water

could suddenly split the hose open.

! Never use hoses that have already been used.

ANTIMICROBIAL SEAL

The seal around the porthole door is made from a special mixture

ensuring antimicrobial protection, thus reducing bacterial proliferation

up to 99.99%.

The seal contains zinc pyrithione, a biocidal substance which reduces the

proliferation of harmful microbes (*) such as batteries and mould prone to

causing stains, unpleasant odours and product deterioration.

(*) According to tests performed by the University of Perugia, Italy

on: Staphylococcus aureus, Escherichia coll, Pseudomonas aeruginosa,

Candida albicans, Aspergillus niger, Penicillium digitatum

In rare cases an allergic reaction may be caused by prolonged contact between seal

and skin.

ACCESSORIES

Contact our Technical Assistance Service to check whether the following

accessories are available for this washing machine model.

Stacking kit

With this accessory you can secure the tumble dryer to the upper part of

your washing machine to save space and facilitate loading and unloading

of the tumble dryer.

TRANSPORT AND HANDLING

Do not lift the washing machine by gripping it from the upper section.

Unplug the appliance and close the water tap. Check that the door and

detergent dispenser drawer are tightly closed. Detach the lling hose

from the water tap then detach the drain hose. Empty all the water

remaining in the hoses and secure the latter so that they do not get

damaged during transport. Apply the transport bolts back on. Repeat, in

reverse order, the transport bolt removal procedure described in the

“Installation instructions”.

TROUBLESHOOTING

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily

solved using the following list.

Anomalies Possible causes / Solution

The washing machine does

not start.

The appliance is not plugged into the socket fully, or not enough to make contact.

There is no power in the house.

The wash cycle does not start.

The washing machine door is not closed properly.

The ON/OFF button has not been pressed.

The START/PAUSE button has not been pressed.

The water tap has not been opened.

A delay has been set for the start time.

The Demo Mode is active (see below how to deactivate).

The washing machine does

not ll with water (“ ”

appears on the display).

The water inlet hose is not connected to the tap.

The hose is bent.

The water tap has not been opened.

There is no water supply in the house.

The pressure is too low.

The START/PAUSE button has not been pressed.

The washing machine

continuously loads and

unloads water.

The drain hose is not tted between 65 and 100 cm from the oor.

The free end of the hose is immersed in water.

The wall drainage system is not tted with a breather pipe.

If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the

Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems relating

to back-siphonage, causing the washing machine to ll with water and drain continuously. Special anti-siphon

valves are available in shops and help to prevent this inconvenience.

The washing machines does

not drain and the symbol

(F9E1) on the display.

Clean the pump lter (see Care and maintenance chapter)

The drain hose is bent.

The drainage duct is clogged.

The washing machine

vibrates a lot during the spin

cycle.

Transport bolts have been not removed correctly during installation.

The washing machine is not leveled.

The washing machine is tucked between furniture cabinets and the wall.

The washing machine leaks.

The water inlet hose is not screwed on properly.

The detergent dispenser drawer is obstructed.

The drain hose is not properly attached.

The symbol appear and

the display visualises an error

code (e.g.: F1E1, F4...).

Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

There is too much foam.

The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and

machine wash”, or the like).

Too much detergent was used.

“ ” phase icon blinks, “0”

spin speed displayed .

Unbalance of laundry load prevented spin cycle, to protect the washing machine.

If you want to spin the wet laundry, add more laundry items of dierent sizes and start “Spin&Drain” programme.

Avoid small laundry loads consisting of few big, absorbent pieces of laundry / wash dierent sizes of articles in one

load.

You can download the SAFETY AND INSTALLATION INSTRUCTIONS, OPERATING MANUAL, TECHNICAL

SHEET and ENERGY DATA by:

• Visiting the website http://docs.hotpoint.eu.

• Using the QR code.

• Alternatively, contact our Technical Assistance Service (the telephone number is indicated in the warranty

booklet). When contacting the Technical Assistance Service, provide the codes shown on the adhesive label applied

to the inside of the door.

xxxxxxxxxxxx

xxxx

Disable the DEMO MODE : The following actions must be carried out in sequence, without breaks. Switch the machine ON and then switch it OFF again. Press

the START/PAUSE button until the buzzer is heard. Switch the machine on again. The “DEMO” indicator ashes and then turns OFF.